GMC GPSM006 Manual 

GPSM006 Power Magnetic GPS Tracker Manual (GSM+GPS+GPRS+SMS) [MAGNETIC GPS CAR TRACKER]

LED Lights Blue LED light is for the GPS. Blinking means it’s connected and constantly means it’s searching for satellites. Green LED light is for the GSM. Blinking means it’s connected and constantly means it’s searching or that the GPRS setting are incorrect/not set. Quick Start Guide Installing the SIM card *Please make sure the SIM card is not password protected Sim card slot Off/On button USB charged Port Alarm Sensor Power Magnetic mAGmagnets USB charged USB micro 5 pin

Content Specs. Content Specs. Dim. 115mm x 60mm x 25mm Weight 204g Network GSM/GPRS Band 850/900/1800/1900Mhz GPS chip UBLOX GPS sensitivity -159dBm GPS accuracy 5m Time To First Fix Cold status 35-80s Warm status 35s Hot status 1s Car charger 12—24V input 5V output Wall charger 110－220V input 5V output Battery Chargeable changeable 3.7V 8000mAh Li-ion battery Standby 100 days Storage Temp. -40°C to +85°C Operation Temp. -20°C to +55°C Humidity 5%--95% non-condensing Userage: SIM card installation 1.Open the rubber plug . 2. Insert the GSM SIM card. 3.Close the rubber plug. Battery and Charger Do charge the battery to capacity in 8 -12 hours for first time. Please use the battery and charger provided by the manufacturer. This unit adopts built-in Li-ion battery, and full battery can standby 80days. After first use, the battery usually should be charged fully in 5--8 hours. Cautions: a: For it’s Li-ion battery, which contains harmful chemicals and may burst, please don’t bump, puncture it violently and keep it off fire. b: Please charge the battery in time to keep it working normally.

Startup  Put the SIM card and battery in place.  Turn on the unit outdoors by pressing the “on/off” button until the indicator is on.  Eg: Step 1. pw,123456,zx,016*******#(GPS SIM Card Number) Step 2. admin 123456+space+your phone number Step 3. apn123456+space+local apn contect Step 4. adminip123456+space+101.1.16.228+space+7700 In 10 or 40 seconds, the unit will begin to work and acquire the GSM signals as well as the GPS signals. The indicator will keep flashing every 3 seconds when the unit has received the signals.  When this unit receives GPS signals normally, you can use it and do any setting as the instructions of this manual. Green LED for GPRS working status Status of indicator Meaning Slow flash (flash 1s after every 2s) GSM / GPRS conversation start Continuously in bright status No GPRS signal Green Led off Device fault or dormant Blue LED for GPS working status Status of indicator Meaning Slow flash (flash 1s after every 2s) GPS location successful Continuously in bright status Searching GPS signal Blue led off Device fault or dormant Red LED for power charging status 1.Google link: click link, there is map when positioning ok, no map means no positioning. 2.V:A GPS signal ok.V:V no GPS signal 3.2016-04-18 11:26:48: the last time receive GPS signal. 4.Spd:000km/h: the speed of tracker ran. 5.Bat:6 battery balance（the range is from 1 to 6） 6.ID:4209504543: ID code of device(used for connect tracking website or APP) 7.S31G07；plmn：50216 GSM operator data 8.Lac：21042，cellid:12543 LBS data Status of indicator Meaning Red led on all the time Charging red led flash Low battery red led off Full battery or charged full

Change the password Set Password: Send sms: “password+old password+space+new password” to the unit to change the password. For Example, pls send sms: “ password123456 000000” to terminal device, it will reply sms: “password OK”. New password 000000 changed in success. Be keep the new password in mind,you have to upload the software to restore the original setting in case of losing the new password. Make sure the new password is in 6 digits Arabic numbers, or the tracker can’t recognize the password. Make sure that all the symbol“+”in sms commends is just for quick understanding, which don’t need to enter “+” in sms, and “space” means press the spacebar button of the cell phone. Authorization Send SMS：“ admin+password+space+cell phone number” to set up a authorized number. The other authorized numbers should be set by the first authorized number. If the number is successfully authorized, the unit will reply “admin ok!” in SMS. Send SMS：“ noadmin+password+space+authorized number” to delete the authorized number. for example, please send：“ admin123456 0126366366” to tracker to set 0126366366 as an authorized number. When the authorized number call the device, it will hang up your phone and reply a real-time latitude and longitude information, as below:

Single Locating If there is no authorized number, when any number dials up the unit, it will report a Geo- info; If there is already an authorized number, then it will not respond when an unauthorized number calls it up. Single message inquires the latitude and longitude information, any telephone number can send instruction “where” to the equipment, the equipment will reply the latitude and longitude information to this telephone. When an authorized number dials up the unit, it will hang up and report a real-time Geo-info as below: Tracking location, When GPS signals is weak, the position of latitude and longitude included in the SMS is the position that the tracker received GPS signals at last. If it is different with its exact current location, pay attention to check the time included in the SMS you got. Auto Track Send SMS command “t030s005n+password” to the tracker device, it will report the “no reply” at 30s intervals for 5 times. (s:second, m:minute, h:hour). This command setting must be in 3 digits and the maximum value is 255. Unlimited times auto track: Send SMS “t030s***n+password” to the tracker device, it will reply the “no reply” continuously at 30 seconds intervals. Cancellation: Send SMS “notn+password” to the tracker device, it will report the “notn ok”. Note: the interval must not less than 20s. Monitor (Voice Surveillance) The command to switch between Track and Monitor are “tracker” and “ monitor”. The default mode is “track” (Track mode). Send SMS “monitor+password” to the unit, and it will reply “monitor ok!” and switch to “monitor” mode. Send SMS “tracker+password” to the unit, it will reply “tracker ok!” and restore to “track” mode

Geo-fence Set up a geo-fence for the unit to restrict its movements within a district. The unit will send the message to the authorized numbers when it breaches the district. Set up: When the unit stays immobile in a place for 3-10 minutes, the user can Send SMS: “stockade+password+space+latitude,longitude; latitude,longitude” to unit to set the restricted district. Remark: The first latitude & longitude is coordinate of the top left corner of the Geo-fence, while the second latitude & longitude is the coordinate of the bottom right corner. Cancel: Send SMS:” nostockade+password” to deactivate this function, tracker will reply “nostockade ok”. Movement alert Set up: When the unit stays immobile in a place for 3-10 minutes, the user can send SMS: “move+password” to the unit, then the unit will reply “move ok!”. In case of such a movement（the unit default distance is 100M）, it will send SMS “Move ALARM+ Latitude and longitude” to the authorized number Cancel: Send SMS:” nomove+password” to deactivate the movement alert, tracker will reply “nomove ok”.

Overspeed alert: Set up: Send SMS: “speed+password+space+050” to the unit (suppose the speed is 50km/h), and it will reply “speed ok!”. When the target moves exceeding 50 km/h, the unit will send SMS :”speed ALARM !+ Latitude and longitude” to the authorized numbers every 5 minutes. Cancel: Send SMS “nospeed+password” to deactivate the overspeed alarm, tracker will reply “nospeed ok”. Remark: The recommended speed should be not less than 50km/h. For below that rate, it will be effected the accuracy by gps signals drift etc. Low battery alert When GPS device battery is going to be about 3.7V, it will send SMS: “bat:l” at 30 minutes interval. Terminal (local) Time Setting Send SMS “time+space+zone+password+space+local time”. For example, Send SMS “time zone123456 8” (time zone of China). If the local time zone is negative as “-3”, then it should set as SMS: “time zone123456 -3”. Bat:low http://maps.google.com/maps? q=00.00000%2c000.00000 v:V,2016-04-18 11:26:48 Spd:000km/h,bat:2,ID:4209504543 ,S31G07;plmn:50216,lac:21042,cell id:12543

Sleeping power-save mode On normal status, when the unit stoped over 10minutes, it will change to sleeping mode, on this mode, the power consumption is 4mah/h only. When it get any command or been moved, it will start GPS locating automatically. Forced sleeping mode, Setting: Send SMS “sleep+password”, the unit will reply “sleep ok”, it enter to forced sleeping power-save mode. Start device, send SMS “nosleep+password”,the unit will reply “nosleep ok”, it start GPRS and GPS locating. Restore factory settings Note: It is effective sending by authorized number Send SMS command “format”, the unit will reply “The tracher will immediateiy restore the factory setting. All previous settings will be canceled.” OR Send “begin+password” in SMS to the unit, it will replay “begin ok” and initialize all the setting. (Default Password:123456) For example, send SMS “begin123456” to the tracker via a cell phone, If succeeded, it will replay “begin ok”

GPRS setting User must send SMS via cell phone to set up IP, port and APN before starting GPRS. Setting up APN APN standards for Access Point Name and differs from country to country. For more information about the local APN, inquire with your local GPRS network operator. Text the tracker a SMS “apn+password + Space + your local APN” via a cell phone and if succeeded in setup, the tracker will return the message “apn ok”. e.g. send SMS command “apn123456 cmnet”. If succeeded, “apn ok” is returned by the tracker in SMS. Notes: 123456 refer to password of tracker and CMNET is the APN of China Mobile (One of GSM Operator in china). Set IP Send SMS command：adminip123456,101.1.16.228.7700 if succeeded, “adminip ok” Dropped Alarm When device have been attracted on metal 10 minutes after ( the Dropped button have been pressed 10 minutes ) ,if it device was dropped , it would alarm to the user by SMS or calling .

Shock alert Note: It is effective sending by authorized number Send SMS command“shock+password”, the unit will reply “shock ok.” Cancel: Send SMS command “noshock+password”, the unit will reply “noshock ok.” Faults & The Solutions Faults Solution Startup Fail Check the battery and see if it is fully charged or correctly installed. Hang up Fail In existence of an authorized number, and unauthorized number dials up the unit. Please initialize the unit and re-set up the authorized numbers. Monitoring Failure Please check sure authorization number is set to the correct time. No GSM Signal Please make sure SIM Card is GSM Net and installed correctly; also call display should be on; but no call transfer and PIN code off. Command List (Please note 123456 is the default password). Feature name Active command Replay Cancel command Replay Begin(blank before set) begin123456 Begin ok Admin number admin123456+space+numb er Admin ok noadmin123456+s pace+number Noadmin ok Sos number sos123456+space+number Sos number ok nosos123456+spac e+number Nosos number ok Sossms sosms123456 Sossms ok nosossms123456 Nosossms ok Soscall soscall123456 Soscall123456 ok nososcall123456 Nososcall ok Password password123456+space+ne w Password ok Sever ip & port adminip123456+space+ip+s pace+port Adminip ok

APN apn123456+space+local apn content Apn ok LBS Addjz=1 Open LBS Addjz=0 Close LBS GPRS gprs123456 Gprs ok nogprs123456 Nogprs ok Time Zone Timezone123456+space+8 Timezone ok Timezone123456+ space+-8 Timezone ok Restore factory setting farmat No replay Upload frequency(10-180s) upload123456+time Upload ok Sleep working mode sleep123456+space+time Sleep time ok Wake up by sms,call press button Shock working mode No sleep working mode nosleep123456 Nosleep ok Get location where or G123456# Google map link One way communication monitor123456 Monitor ok In this mode,you could hear the voice araound units after call it Shock alarm shock123456 Shock ok noshock123456 Noshock ok Shock call alarm vibcall123456 Shock call alarm ok Shock sms alarm vibsms123456 Shock sms alarm ok Move alarm (distance:100- 5000m) move123456+ space+distance Move ok nomove123456 Nomove ok Overspeed alarm(50-120km/h) speed123456+space+max speed Speed ok nospeed123456 Nospeed ok Set a geo- fence(stockade) stockade+123456+space+lo ng,lat;long,lat Stockade ok nostockade123456 Nostockade ok Check setting of device Param1 Software version,date, imei,ip & port,apn,web platform Param2 Admin number,sos number,move distance,speed,etc Status of device status Bat:4,gprs:1,gsm:3,gsm: 1,acc:0,oil:0,power:1,s:0 Language Lag1 Switched to english

Webplatform and GMGPS app If you wish to use the web platform or GMGPS application you’ll need the server and port settings to be able to connect to them. Below you can find the default server settings: Server URL Sever IP Port www.gm63gps.com 101.1.16.228 7700 Login on web platform Go to the following url: www.gm63gps.com and login with your IMEI number (see image) and password (default: 123456). Keep this information to yourself and please be aware who you share this information with. It is wise to change your password from day 1. This can be done on the website by clicking on “change password” in the top-right corner. Login in iOS and Android app GMGPS app is compatible with iOS and android. After downloading the application start the app, press on “log in by IMEI” and login with your IMEI (see 5.1) and password (default: 123456). By default the server must be set to www.gm63gps.com. App download Android & iOS version: scan below QR code or Search GMGPS & “GMGPS”in app store Login using your IMEI and password. IMEI Number

Functionalities in the GMGPS APP Real-time Follow the selected tracker on a map Historical See all previous location updates Geofence Manually set a safezone Issue Command Send commands to the tracker by SMS or GPRS Device Info View and edit the tracker information Device (message) This is where you can view all given alert message Alarm Setting This is where you can turn on/off each alarm message

Realtime/实时跟踪 Historical/历史轨迹

Geofence/ 电子栅栏

Issue Command /命令下发

Command/ 常用指令 Set Master number/ 设置主控号码

Set SOS number/ 设置亲情号码 Set Move Alarm/ 开启移位报警

Set OverSpeed alarm/ 开启超速报警 General/ 普通指令

SOS alarm/ SOS 报警 Language/ 语言选择

Device info/ 设备信息 Alarm setting/ 报警提醒

Functionalities on www.gm63gps.com web platform In the top area we have the following functionalities: Monitor This is where you can view all your trackers on a map and see their current/last known position. Statistics Statistics gives you insight of the usage, like the amount of kilometres made in a certain period

Device For an overview of all the trackers you can use device page. It shows you all your trackers and their status. You can edit them straight away from here. Your profile The name shown after the “Hello!” is a clickable link which grands you access to your profile. You can edit your preference and contact information. Change Password Change your default password (123456) to any wanted password you want. In the side bar area you have the following functionalities: Tracking Start tracking the selected device from this moment on. The map will show a path of each location update. Playback See all previous location updates here with a extra option to export it to a EXCELL file. Click on the following link”download track” to download the EXCELL. Target Info Edit and view the device information.

Geo-Fence This gives you the possibility to setup geo-fences with a given name. GPS Position When your car is stolen or if you wish to track your car real-time for a certain period this option gives you the possibility. Please keep in mind using this option reduces the battery lifetime. So please keep in mind when using this option to turn it off after you found your car or when your done using real time tracking. Time Value: Use real time tracking for a period of 5 ~ 360 minutes. It will stop real time tracking by itself after the given period. On: Turns on real time tracking till you turn it off yourself with the “OFF” option. Off: turns off real time tracking.

FAQ (Problems solving) 1. The tracker is on but I don’t see any location information on the webplatform/app Please make sure the device is connected to the GSM/GPRS network. If the green LED light is not blinking this means it is trying to connect to the GSM/GPRS network. This could indicate you have set the wrong APN settings. But this could also mean you don’t have enough credits on your SIM card. Please check and test the SIM card on a other device with SIM card support. 2. The GSM LED (green) keeps chining constantly This indicates that the device is connecting to the GSM/GPRS network or that it failed to connect the GSM/GPRS network. Please make sure the SIM card is inserted ( correctly) in the slot and that the SIM card has no PIN code active. If this is correctly done check FAQ1. 3. The GPS (blue) keeps shining constantly This indicates the device is trying to connect with GPS satellites. If this takes longer than 120 seconds it would be smart to find a new spot a new spot to place/attach the tracker. The tracker was unable to connect to any GPS satellite. 4. I can’t call the tracker Please make sure you are calling with the admin number. If this is not the cause please check if the device is on (green LED blinking) 5. I can’t login on my account (webplatform/app) Please follow the steps in chapter 4 first. If this won’t solve the problem contact us on www.gmgps63.com 6. The tracker won’t turn on anymore Please check if the power switch is set to “on” (on the side of the SIM card slot). 7. I don’t receive a responds after sending a command Please check if the device in on (green LED burning) and please make sure your SIM card supports sending SMS. To force the device to come online, press and hold the blue button for 15 seconds and wait for the green LED to start blinking. check if you have enough credits on your account of the SIM card. 8. The green lines on the playback are not the actual route I took This is correct. The green lines are only there to show you the timeline between location updates. So this is not a indication of how you walked, drove or what so ever. 9. The LED lights are all off This means the device is off or it’s in sleep mode. If the power switch is on press and hold the blue button for 15 seconds. The device should wake up from its sleep mode. You will see LED light shine/blink again.

Start up Setting / 简易设置 Step 1 *Tracker setting / 定位器设置* pw,123456,zx,01********# (GPS Device SIM Card Number) Step 2 * APN setting / APN 设置* apn123456,****** ( local apn content ) Step 3 *Server IP / IP 设置* adminip123456,101.1.16.228.7700 #Apn for telco in Malaysia /APN 对应表： 1.Digi = diginet 2.Maxis = unet 3.Celcom = celcom3g 4.Umobile = my3g 5.Tune Talk = tune talk 6.Altel = altel 7.RedOne = redone #APN for telco in Singapore / APN 对应表： 1.Singtel = (Prepaid) hicard , (Postpaid) e-ideas 2.StarHub = shppd 3.M1 = sunsurf