GoMax Electronics SP-1014 Operation & User’s Manual

with HDCP Support User Manual rev: 111209 Made in Taiwan SSPP--11001144

conformance to safety regulations and requirements, and has been certified for international use. However, like all electronic equipments, the SP-1014 should be used with care. Please read and follow the safety instructions to protect yourself from possible injury and to minimize the risk of damage to the unit. ● Follow all instructions and warnings marked on this unit. ● Do not attempt to service this unit yourself, except where explained in this manual. ● Provide proper ventilation and air circulation and do not use near water. ● Keep objects that might damage the device and assure that the placement of this unit is on a stable surface. ● Use only the power adapter and power cords and connection cables designed for this unit. ● Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning. TABLE OF CONTENTS INTRODUCTION................................................................................................................. 1 FEATURES ......................................................................................................................... 1 PACKAGE CONTENTS ...................................................................................................... 1 SPECIFICATIONS .............................................................................................................. 2 PANEL DESCRIPTIONS ..................................................................................................... 3 HARDWARE INSTALLATION ............................................................................................. 4 CONNECTION DIAGRAM .................................................................................................. 4 DIP SWITCH ....................................................................................................................... 5 PIN DEFINITION ................................................................................................................. 6 NOTICE .............................................................................................................................. 7 WARRANTY ....................................................................................................................... 8

solution by which the high definition video and high quality audio can be transmitted to different locations over a long distance. The devices are cascadable, allowing you to extend DVI compliant displays almost anywhere. The input DVI source can be duplicated and distributed to up to 4 DVI-enabled displays through cost effective Cat-5/5e/6 cables and Cat.X receiver (CV-711) and/or mini-receivers (CV-711S). FEATURES ● HDMI founder Silicon Image chipsets embedded for superior compatibility and reliability ● DVI 1.0 compliant ● Supports HDCP ● Supports default DVI EDID and has the ability to learn the EDID of displays ● Extends up to 30m (100ft) at UXGA 1600x1200@60Hz ● Extends up to 60m (200ft) at 1024x768@60Hz ● Allows cascading ● Perfectly integrated with other DVI over CAT5 series products ● Wall mountable PACKAGE CONTENTS ● 1x SP-1014 ● 1x DC 5V 4A in-line with C7 power cord ● 1x User Manual The length depends on the characteristics and quality of the cables. Higher resolutions and longer transmission distances require low skew cables (<25ns/100m) for best performance. Unshielded CAT6 with metal RJ45 connectors is recommended.

1x4 Distribution Amplifier Transmitter [TX] Receiver [long range RX] Receiver [short range RX] DVI compliance DVI 1.1 HDCP compliance No Yes Yes Video bandwidth Single-link 165MHz [4.95Gbps] Video support Up to (Single) WUXGA 1920 × 1200 @ 60 Hz Video transmission over category cable With CV-17-RX: 30m (100ft) at 1600x1200 60m (200ft) at 1024x768 With CV-117: 15m (50ft) at 1600x1200 30m (100ft) at 1024x768 Equalization N/A 8-level digital None Input TMDS signal 1.2 Volts [peak-to-peak] Input DDC signal 5 Volts [peak-to-peak, TTL] ESD protection [1] Human body model — ±19kV [air-gap discharge] & ±12kV [contact discharge] [2] Core chipset — ±8kV PCB stack-up 4-layer board [impedance control — differential 100Ω; single 50Ω] Input 1x DVI 1x RJ45 1x RJ45 Output 4x RJ45 1x DVI 1x DVI DVI connector DVI-I [29-pin female] DVI-I A [29-pin female] DVI-D [25-pin male] RJ45 connector WE/SS 8P8C with 2 LED indicators Rotary switch 2-pin None None Mechanical SP-1014[TX] CV-17[RX] CV-117[RX] Housing Metal enclosure Metal enclosure Plastic molding Dimensions [L x W x H] Model 215 x 85 x 40mm [8.5" x 3.3" x 1.6"] 82 x 62 x 24mm [3.2" x 2.4" x 1"] 40 x 50 x 20mm [1.6" x 2" x 0.8"] Package 330 x 200 x 95mm [1'1" x 7.9" x 3.7"] 170 x 115 x 40mm [6.7" x 4.5" x 1.6"] Carton 495 x 440 x 380mm [1'7" x 1'5" x 1'3"] 450 x 370 x 300mm [1'5.7" x 1'2.6" x 11.8"] Weight Model 525 [1.2 lbs] 182g [6.4oz] 50g [1.8oz] Package 985 [2.2 lbs] 140g [5oz] Fixedness Wall-mount with screws Wall-mount with screws Direct plug-in Power supply 5V 4A DC 5V 2A DC None Power consumption 10 Watts [max] 1 Watt [max] 0.5 Watt [max] Operation temperature 0~40°C [32~104°F] Storage temperature -20~60°C [-4~140°F] Relative humidity 20~90% RH [no condensation]

Rear Panel 2. DIP SWITCH: see more detail in the next page 3. DVI-D INPUT: connect to one DVI source here 4. DVI-D Signal OUTPUT 1~4: link to each DVI display via a Cat-5/5e/6 cable with a DVI over Cat.X receiver CV-711 or CV-711S. 5. USB: For firmware update use only 6. +5V DC: interlocking power jack for 5V DC power supply unit When the connected DVI / HDMI monitor is verified as DVI or HDMI and HDCP compliant, the corresponding green LED will blink.

1. Switch off all devices, including displays. 2. Connect the DVI source to the DVI-D INPUT port. 3. Connect the receivers (CV-711 or CV-711S) via solid Cat-5/5e/6 cables to each DVI-D Signal OUTPUT port. 4. Plug in the 5V 4A DC interlocking power supply unit. 5. Power on the DVI displays. 6. Power on the DVI source. CONNECTION DIAGRAM

Default Mode 1 1 – EDID preferred timing is 1920x1080 OFF [] ON [] Up to 1024x768 Default Safe Mode 1 – EDID preferred timing is 1024x768 ON [] OFF [] Up to 1680x1050 Default Mode 1 2 – EDID preferred timing is 1680x1050 ON [] ON [] Learn Display EDID Learning 2 Mode – for learning EDID from the display Note 1 If you want to change default EDID Mode, please set DIP switch position which you want and power cycle the device. 2 If you want to learn the display EDID, please connect display DVI connector to machine DVI-IN connector and set DIP switch to ON-ON, then power cycle the device and wait for 5-10 seconds. 3 Unless you want to change the EDID, do not change the DIP setting.

Pin 1 TMDS Data 2- Pin 10 TMDS Data 1+ Pin 18 TMDS data 0+ Pin 2 TMDS Data 2+ Pin 11 TMDS Data 1/3 shield Pin 19 TMDS data 0/5 shield Pin 3 TMDS Data 2/4 shield Pin 12 TMDS Data 3- Pin 20 TMDS data 5- Pin 4 TMDS Data 4- Pin 13 TMDS Data 3+ Pin 21 TMDS data 5+ Pin 5 TMDS Data 4+ Pin 14 +5V Pin 22 TMDS data 5+ Pin 6 DDC clock Pin 15 Ground Pin 23 TMDS clock+ Pin 7 DDC data Pin 16 Hot plug detect Pin 24 TMDS clock- Pin 8 Analog vertical sync Pin 16 Hot plug detect Pin 9 TMDS Data 1- Pin 17 TMDS data 0- RJ45 / Cat.X

provide DVI display EDID information. 2. All DVI over Cat.X transmission distances are measured using Belden 1583A CAT5e 125MHz UTP cable and ASTRODESIGN Video Signal Generator VG-859C. 3. The transmission length is largely affected by the type of Cat-5/5e/6 cables, the type of DVI sources, and the type of DVI display. The testing result shows solid UTP cables (usually in the form of 330m [1,000ft] bulk cables) can transmit a lot longer signals than stranded UTP cables (usually in the form of fixed length patch cords). Shielded STP cables are better suited than unshielded UTP cables. A solid UTP Cat-5e cable shows longer transmission range than stranded STP Cat-6 cable. For long extension applications, solid UTP/STP cables are the only viable choice. 4. EIA/TIA-568-B termination (T568B) for Cat-5/5e/6 cables is recommended for better performance. 5. To reduce the interference among the unshielded twisted pairs of wires in Cat-5/5e/6 cable, one can use shielded STP cables to improve EMI problems, which is worsen in long transmission. 6. Because the quality of the CAT5/6 cables has the major effect on how long the transmission limit can achieve and how good is the received picture quality, the actual transmission range is subject to one's choice of Cat-5/5e/6 cables. For desired resolutions greater than 1080i or 1280x1024, a Cat-6 cable is recommended. Performance Guide for HDMI over Category Cable Transmission Performance rating Type of category cable Wiring Shielding CAT5 CAT5e CAT6 Solid Unshielded (UTP)    Shielded (STP)    Stranded Unshielded (UTP)    Shielded (STP)    Termination Please use EIA/TIA-568-B termination (T568B) at any time

from defects in the material and workmanship for 1 year from the date of purchase from the SELLER or an authorized dealer. Should this product fail to be in good working order within 1 year warranty period, The SELLER, at its option, repair or replace the unit, provided that the unit has not been subjected to accident, disaster, abuse or any unauthorized modifications including static discharge and power surge. This warranty is offered by the SELLER for its BUYER with direct transaction only. This warranty is void if the warranty seal on the metal housing is broken. Unit that fails under conditions other than those covered will be repaired at the current price of parts and labor in effect at the time of repair. Such repairs are warranted for 90 days from the day of reshipment to the BUYER. If the unit is delivered by mail, customers agree to insure the unit or assume the risk of loss or damage in transit. Under no circumstances will a unit be accepted without a return authorization number. The warranty is in lieu of all other warranties expressed or implied, including without limitations, any other implied warranty or fitness or merchantability for any particular purpose, all of which are expressly disclaimed. Proof of sale may be required in order to claim warranty. Customers outside Taiwan are responsible for shipping charges to and from the SELLER. Cables and power adapters are limited to a 30 day warranty and must be free from any markings, scratches, and neatly coiled. The content of this manual has been carefully checked and is believed to be accurate. However, The SELLER assumes no responsibility for any inaccuracies that may be contained in this manual. The SELLER will NOT be liable for direct, indirect, incidental, special, or consequential damages resulting from any defect or omission in this manual, even if advised of the possibility of such damages. Also, the technical information contained herein regarding the SP-1014 features and specifications is subject to change without further notice.