International Datacasting STAR Generation 2 Operation & User’s Manual
Read Online
Read the International Datacasting STAR Generation 2 Operation & User’s Manual online using the built-in PDF viewer.
Text of the manual
S T A R G e n 2 R e c e i v e r U s e r ’ s G u i d e
Page 2 of 47
Table of Contents
SAFETY WARNINGS ................................................................................................................................ 4
GETTING STARTED ................................................................................................................................. 5
Models .................................................................................................................................................. 5
How to Use This Guide ........................................................................................................................ 5
QUICK START ........................................................................................................................................... 5
What You Should Have Received ........................................................................................................ 5
The Front Panel .................................................................................................................................... 6
The Rear Panels – STAR-Four & STAR-Two ...................................................................................... 7
Default Settings .................................................................................................................................... 7
First Installation and Configuration of the STAR ............................................................................... 7
USER INTERFACE .................................................................................................................................... 9
Remote Control with a WEB Browser .................................................................................................. 9
The Menu Bar ....................................................................................................................................... 9
Identity .................................................................................................................................................... 9
Input ...................................................................................................................................................... 10
SAT-IN ............................................................................................................................................. 10
IP-IN ................................................................................................................................................. 11
DVB-TS ................................................................................................................................................. 12
Decoder ................................................................................................................................................ 13
Decoder Audio ................................................................................................................................. 13
Decoder Backup Channel x ............................................................................................................. 14
Decoder Data .................................................................................................................................. 15
Output ................................................................................................................................................... 15
Control .................................................................................................................................................. 16
Control MGMT IP ............................................................................................................................. 16
Control MGMT Notification Mode .................................................................................................... 17
Control MGMT Notification Priority .................................................................................................. 18
Control MGMT Notification Destination ........................................................................................... 18
Control I/O ....................................................................................................................................... 18
Control ACMM ................................................................................................................................. 18
Alarm .................................................................................................................................................... 19
Alarm Menus and Sub Menus ......................................................................................................... 20
Status ................................................................................................................................................... 21
Utility .................................................................................................................................................... 25
Logout .................................................................................................................................................. 28
ADVANCED TOPICS .............................................................................................................................. 29
Using your PMR ................................................................................................................................... 29
Time Shifting ....................................................................................................................................... 29
Using Date and Time .......................................................................................................................... 30
Recording and Playback Reports ....................................................................................................... 31
GUI TIPS .................................................................................................................................................. 32
Drop down Menus .............................................................................................................................. 32
Valid numeric Ranges ........................................................................................................................ 32
Text in Red ......................................................................................................................................... 32
FAQ’S ...................................................................................................................................................... 33
Why are there periods of silence in my playback? ............................................................................. 33
If a reboot occurs during playback what happens to the playback? .................................................. 33
S T A R G e n 2 R e c e i v e r U s e r ’ s G u i d e
Page 3 of 47
Why can I not always edit active time shift recording or playbacks? ................................................. 33
I changed my SD card; do I lose all the recording and playback schedules? .................................... 33
How many recordings can I store? ..................................................................................................... 33
Can I take information off the receiver? ............................................................................................. 33
If a playback is interrupted, what will happen? ................................................................................... 33
How many playbacks can I add to a scheduled event? ..................................................................... 34
How long does the recording and playback information stay on the receiver? .................................. 34
What happens to recordings over Daylight Savings Time changes and on a leap year? .................. 34
The Warning LED is illuminated, what does this mean? .................................................................... 34
The Alarm LED is showing, what does this mean? ............................................................................ 34
REMOTE CONTROL BY SNMP.............................................................................................................. 36
CONNECTOR SPECIFICATIONS ........................................................................................................... 37
KEYPAD CONTROL ............................................................................................................................... 38
Measurement Displays ....................................................................................................................... 38
Settings Menu Flowchart .................................................................................................................... 39
WEEE DISPOSAL INSTRUCTIONS ....................................................................................................... 45
WARRANTY & SERVICE INFORMATION ............................................................................................. 45
S T A R G e n 2 R e c e i v e r U s e r ’ s G u i d e
Page 4 of 47
Safety Warnings
THE UNIT MUST BE INSTALLED BY A QUALIFIED SERVICE PERSON AND THE EXTERNAL
EARTH CONNECTION MUST BE MADE BEFORE CONNECTING THE AC SUPPLY. USE A
GROUNDED POWER OUTLET ONLY.
AN ANTI-SHOCK DEVICE MUST BE INSTALLED ON THE ANTENNA CABLE CONNECTING TO
THE UNIT.
THE UNIT MUST BE GROUNDED AT THE REAR PANEL GROUND CONNECTION.
DO NOT OPERATE THE UNIT IN DIRECT SUNLIGHT, A DUSTY OR DAMP ENVIRONMENT AND
DO NOT BLOCK THE VENTILATION HOLES. THE UNIT IS DESIGNED TO OPERATE IN A
TEMPERATURE RANGE OF 0ºC TO 40ºC. THE POWER RATING AND HEAT GENERATION OF
THE UNIT ARE SUCH THAT IT CAN BE PLACED IN A 19” CABINET WITHOUT SPECIAL
COOLING FACILITIES. HOWEVER, SUFFICIENT CLEARANCE MUST BE MAINTAINED
BETWEEN THE UNIT AND OTHER EQUIPMENT (A 1RU GAP).
DO NOT OPEN THE UNIT FOR ANY REASON. THIS IS DANGEROUS AND MAY VOID YOUR
WARRANTY.
IF THE UNIT FAILS TO OPERATE CALL YOUR SERVICE PROVIDER CUSTOMER SUPPORT.
THE STAR IS A 19” 1U RACK-MOUNTING UNIT WITH CONNECTOR ACCESS AT THE
REAR. THE UNIT CAN BE MOUNTED AT THE FRONT OF A 19” RACK USING AN
APPROPRIATE MOUNTING SET. HOWEVER, THE USE OF LATERAL SUPPORT IS
STRONGLY RECOMMENDED.
S T A R G e n 2 R e c e i v e r U s e r ’ s G u i d e
Page 5 of 47
Getting Started
International Datacasting Corporation (IDC) would like to thank you for purchasing this STAR Generation 2
receiver (herein referred to as the “receiver”). This User’s Guide provides step by step instructions on how to
connect the receiver, access satellite services, and set system and audio output configurations.
Models
Your STAR Generation 2 receiver is one of a family of STAR receivers. A datasheet at the end of this document
provides the Technical Specifications of your STAR receiver. Readers of this manual who use a STAR-Two
receiver should ignore any references to audio 3 & 4, decoder 3 & 4 or channel 3 & 4.
How to Use This Guide
This guide describes the operation of your receiver through the GUI and through the keypad interface. Within
the document you will find:
o
a Quick Start section about connecting to the receiver and what the displays mean.
o
a User Interface section explaining how to use the GUI interface to configure the receiver and
enable the outputs.
o
an Advanced Topics section on how to use the Professional Media Recorder (if installed).
o
a GUI Tips section explaining extra information and on-screen choices.
o
a FAQ section.
o
a Keypad Control section for local control of your receiver.
Quick Start
If you have installed IDC products before, you can skip this section. If not, you will be familiarized with the status
and controls of the STAR receiver prior to being shown how to find the receivers IP Address and how to connect
to it through the GUI to configure the receiver for use.
What You Should Have Received
You should have received the following package:
o
One (1) STAR- Generation 2 Receiver;
o
One (1) power cord, suitable for use in your country;
o
One (1) copy of this User’s Guide – also available online from the IDC Customer Service FTP site.
You will need audio cables to connect the receiver to your system. Please keep one set of packaging that your
receiver came in, to allow for a safe return for repair if required.
S T A R G e n 2 R e c e i v e r U s e r ’ s G u i d e
Page 6 of 47
The Front Panel
The STAR front panel contains nine LED indicators, a headphones jack and a keypad LCD combination.
[1]
Headphones
[2]
Status information: STAR-Four
STAR-Two
The status information of the receiver is shown in the LEDs as described in the table below. A blank cell shows
an unused status/colour combination.
[3]
LCD
The LCD display is used to view receiver status, view receiver configurations and/or set receiver configurations.
How to access these settings is described in the section Keypad Control.
[4]
Keyboard
LED status indication
Indication
OFF
GREEN / Flashing Green
RED
YELLOW
LOCK
Unit disconnected
or power failure
Locked to carrier
Not locked to carrier
WARNING No warning
Warning
ALARM
No alarm
Alarm
AUDIO 1/2 No service
Audio OK / Playing local file
PID/MPE-IP or audio error
REMOTE
No M & C link
Link connected remotely
Local control; link available
AUDIO 3/4 No service
Audio OK / Playing local file PID/MPE-IP or audio error
OPTION
Future Use
RECORD
Recording
/ Recording programming
1
2
3
4
Scroll buttons (4)
Select button
Cancel button
S T A R G e n 2 R e c e i v e r U s e r ’ s G u i d e
Page 7 of 47
The Rear Panels – STAR-Four & STAR-Two
[1]
Grounding
[2]
Mains AC 100-240v built in fuse 2.5A
[3]
Alarm contacts (3)
[4]
Audio In (Future use)
[5]
Audio Channels & Relays 1, 2, 3 & 4
[6]
ASI In or ASI Out [Factory installed option]
[7]
Data LAN
[8]
RS232 Comm port
[9]
Monitor & Control LAN
[10]
L-band input and loopthrough
[11]
SD card slot
[12]
Recovery reset
Default Settings
Your STAR receiver is supplied with these default settings:
1. Control mode is: remote
2. IP mode is: DHCP
First Installation and Configuration of the STAR
1. Connect power to the power inlet without connecting the L-band cable to your STAR receiver. The front
panel LCD will show “Star Four G2 Booting OS”. The LEDs on the front panel show (on the left):
2. After a few seconds all LEDs flash once and the LCD screen will display “Initializing”. When initialization
is complete after a few seconds, the LEDs show (on the right), with no external connections:
1
3
5A
5C
7
9
10
12
11
8
4
2
5B
5D
6
S T A R G e n 2 R e c e i v e r U s e r ’ s G u i d e
Page 8 of 47
INDICATIONS
COLOR
LOCK
NONE
WARNING
YELLOW
ALARM
RED
AUDIO 1
NONE
AUDIO 2
NONE
REMOTE
NONE
AUDIO 3 /OPTION 1
NONE
NONE
AUDIO 4 /OPTION 2
NONE
NONE
RECORD
NONE
INDICATIONS
COLOR
LOCK
RED
WARNING
RED
ALARM
RED
AUDIO 1
RED
AUDIO 2
RED
REMOTE
NONE
AUDIO 3 /OPTION 1
RED
NONE
AUDIO 4 /OPTION 2
RED
NONE
RECORD
NONE
3. Connect the STAR to a DHCP IP network. If a DHCP network is not available you can use the LCD to
configure a static IP address (Control>MGMT> IP Static Address). The STAR default is 192.168.0.1. Then
connect the STAR with a switch or computer; and set your computer IP address in the same range.
4. Connect a personal computer to the receiver, open a web browser and connect to the receiver by typing the
IP address of the receiver in your browsers address bar.
5. Login with: Username: admin. Password: 12345. You can change the login username and password
with the web GUI in the “CONTROL>MGMT>IP” menu under “Web”.
Your STAR receiver is now ready for use.
Note: On subsequent startup of the STAR receiver a comprehensive check of the SD card structure and content
takes place. This can delay the appearance of Trigger information on the Utility Trigger page by up to 20
seconds.
S T A R G e n 2 R e c e i v e r U s e r ’ s G u i d e
Page 9 of 47
User Interface
The receiver can be configured through the Graphical User Interface or from the front panel Keypad.
Remote Control with a WEB Browser
When you have logged in, you will see the Web Configuration Manager page.
The Menu Bar
There are 8 top level menus and a logout button in the menu bar presented here in order left to right.
Identity
In the Identity page you can fill in specific information that will be visible on the Welcome page and you can also
include a link that points to a manual.
Device name, Device type,
Serial number, Firmware
version and activated Options.
Menu bar (see below for details).
Follow the Link to an online
Manual. Define the link in the
“IDENTITY” menu. See next page.
Monitoring Status & Routing.
Warning & alarms indicator.
Log and Syslog viewing links.
Time, Date& Synchronization
with SNTP server.
S T A R G e n 2 R e c e i v e r U s e r ’ s G u i d e
Page 10 of 47
DEVICE NAME, DEVICE LOCATION, DEVICE CONTACT, and DEVICE INFO 1-12: enter additional
information which will be visible at the WELCOME page of the WEB GUI. This information can be a link to
another website.
DEVICE MANUAL LINK: this link to a server can be defined to point to a manual. The link button MANUAL will
be found on the menu bar when a link is defined. Link Examples are: file://///server/share/path, ftp://server/file,
ftps://server/file, http://sitelink, https://sitelink.
Input
There are 2 input sources: SAT-IN (which is a satellite L-Band signal) and IP-IN (a Transport Stream over IP
input). A factory installed optional ASI input is also available, and is set up under Menu: DVB-TS> INPUT.
SAT-IN
Different types of outdoor LNBs are supported. For easy setup, the Local Oscillator (LO) frequency can be
entered. However, when the STAR receiver is used with Netmanager control the LO frequency needs to be set
to 0 KHz, and all receiver frequencies need to be entered in the L-band range only.
NCC = Network Control Channel, which contains the network control data generated by IDC’s Netmanager2.
Polarization in the Carrier definition menu’s are only available when the LNB mode is set to “Universal”.
The preferred carrier setting is useful when a transition to a carrier is needed. This function is also supported
and controlled by NCC. If only one Carrier setting is required the Prefered can be set to “Carrier A (or B) only.
S T A R G e n 2 R e c e i v e r U s e r ’ s G u i d e
Page 11 of 47
The options to set the other carrier will be removed from the receivers interface when “Carrier A (or B) only” is
selected. This feature is not controlled by NCC.
The 12 digit BISS session keys A and B are normally provided from the head end. They can be entered here
and show as “- - - - “ when not present and “ * * * *” when present.
IP-IN
LOCAL PORT Mode: Select between AUTO (up to 1Gbit) or 100 Mbit (Half or Full duplex).
LOCAL PORT IP Address: This is the IP Address in the LAN network.
S T A R G e n 2 R e c e i v e r U s e r ’ s G u i d e
Page 12 of 47
INPUT STREAM IP Address/UDP Port: This is the IP Address/Port number on which the MPEG2 TSoverIP
stream is received.
DVB-TS
INPUT: Decoder input can be selected between SAT-IN (L-band tuner), IP-IN (TSoIP) or ASI-IN (As Factory
installed option only). .
PID LIST: This allows you to enter and enable the Network Time Protocol (NTP) PID, the Network Control
Channel (NCC) PID, the Electronic Channel Guide (ECG) PID and the FlexKey (ECM) PID if the option is
installed. MPE PIDs that are required to decode IP Audio services are automatically loaded to each decoder’s
PID list and are not shown here.
DVB-TS FLEXKEY: (Optional) This setting is needed to identify the IP address and port number which contains
the ECM messages sent by Flexkey Encryptor. Requires ECM PID.
S T A R G e n 2 R e c e i v e r U s e r ’ s G u i d e
Page 13 of 47
Decoder
Decoder Audio
CHANNEL x Audio:
STREAM: when stream is set to MPE then select from:
MODE: OFF, CHAN.GUIDE, USER DEFINED, TONE.
Note: If Channel Guide mode is selected, the receiver will populate the service list automatically.
The channel information is provided by the SDP packets from the Event Managers at the head-
end. The MPE PID (ECG PID) for the SDP packets must be added to the receiver PID list to get
the list of Services. The Channel Guide is the list of programs you can select in MPE mode. The
user selects the wanted service, and the unit will select the appropriate IP address and PORT
number. In MPE mode this address and port has to be done manually.
Note: If tone is selected the receiver outputs a 1Khz note.
STREAM: when stream is set to PES then select from:
MODE: OFF, PSI, PID, TONE.
Note: In PSI mode the receiver will populate its service list from the PSI table in the DVB carrier.
The user selects the wanted service, and the unit will select the appropriate PID. In PID mode this
PID has to be set manually.
Note: If tone is selected the receiver outputs a 1Khz note.
SERVICE: shows the list of services available. When there is no list “SIGNAL?” will be shown.
15 kHz LOWPASS: ON/OFF. Enabling the low pass filter limits the upper frequency range to 15Khz
with a 3db/octave attenuation.
GAIN: Set the gain from -18 to +18 dB, in steps of 1 dB.
STEREO/MONO: Select Stereo (Dual), Mono L+R, Mono L, Mono R.
DELAY: Input presentation delay from 0 to 8000 milliseconds.
S T A R G e n 2 R e c e i v e r U s e r ’ s G u i d e
Page 14 of 47
OPTIONAL (not shown):
LIMITER ENABLED: ON/OFF.
LIMITER LEVEL: -50 to 0 dBFS, in steps of 1 dB.
LIMITER RECOVERY: 20 (Fast) to 100 (Slow) Milliseconds recovery time.
Decoder Backup Channel x
The backup for each audio channel can be enabled/disabled and the order of choice for the backup
source can be defined. Additionally each backup source can be viewed and or configured. As delivered
there are no audio backup files on the SD card. Multiple audio files (.mp2 or .mp3) can be stored in the
SD card root directory, but only one can be identified as the default file for each decoder. If the Service
Operator has delivered a backup playlist this will be played instead of the default file (If enabled). Consult
Service Operator for full details.
PRIORITY: Select the order of the available backup sources.
BACKUP PLAYLIST: Select the audio file from the SD card to be played as backup for this Decoder.
Note: If a Backup Playlist is available from the Head end it will be played instead. If the Backup
Playlist has any missing content, that content will be skipped over and the playlist will continue to
play (loop playback). If there is no Backup Playlist the receiver will go to the next priority Backup.
IP STREAM: Choose the SOURCE of the Backup audio from: INTERNET SERVICE; RTP/IP AUDIO or
MPEG TS OVER IP. Once selected the required SOURCE calls up the appropriate set of parameters to
specify the addressing.
Note: In INTERNET SERVICE source, Port Mapping uses the Service ID+10,000 as the port
number (User equipment configuration is required). User Defined allows the user to specify the
port number.
Note: In MPEG TS over IP, Auto in PID Mode uses as backup any PID in the IP-IN transport
stream that matches the current program. Manual allows the user to specify the PID played.
S T A R G e n 2 R e c e i v e r U s e r ’ s G u i d e
Page 15 of 47
Decoder Data
CHANNEL x Data:
STREAM: when stream = MPE (in menu DECODER>AUDIO) then:
MODE: OFF, ANC. DATA AUDIO CH1 (Data on Channel xA), ASYNC. DATA (Data on channel xB).
Note: ANC. DATA is data transport in the ancillary field of coded audio. ASYNC. DATA is data
transport in the MPE RTP header of audio stream.
STREAM: when stream = PES (in menu DECODER>AUDIO) then:
MODE: OFF, ANC. DATA (data on Channel xA), PRIV. DATA (data on Channel xB).
Note: ANC. DATA is data transport in the ancillary field of coded audio. PRIV. DATA is data
transport in a separate PID of the transport stream.
FORMAT: IRT, J.52.
Note: these formats for embedded Async data are only available if Device Special 2 is installed.
PROCESS: MUX, OFF.
BAUD: Output baud rate of the Anc/Async data: 1200, 2400, 4800, 9600, 19k2, 38k4, 57k6 baud.
Output
MODE: Auto (up to 1GB), 100Mb HD, 100Mb FD.
IP ADDRESS: The source address of the output stream.
OUTPUT STREAM: Enabled,
Note: In Disabled mode the (multicast) IP Address and UDP Port are not available.
Note: ASI-OUT is available only with Factory installed option: ASI-OUT.
S T A R G e n 2 R e c e i v e r U s e r ’ s G u i d e
Page 16 of 47
Control
Control MGMT IP
Choose the parameters to configure the network connections, utilize SNMP, specify the SNTP server, a
Syslog server, configure the web access and change the username/password combination.
S T A R G e n 2 R e c e i v e r U s e r ’ s G u i d e
Page 17 of 47
MODE: DCHP, MANUAL
Note: In DCHP mode Static Address, Subnet Mask and Gateway Address are not available. .
Control MGMT Notification Mode
Choose the parameter (ALL; HEARTBEAT; SETTING CHANGED; CONTROL MODE CHANGED;
CONTROL MODE LOCAL SUPPRESS) that produces a notification and the type of that notification (OFF;
WARNING; WARNING+ALARM) to the SNMP trap set under Control>MGMT>Notification>Destination.
S T A R G e n 2 R e c e i v e r U s e r ’ s G u i d e
Page 18 of 47
Control MGMT Notification Priority
Select the priority for the notifcation of an alarm in a parameter. Each parameter shown on the Control MGMT
Notification Mode Alarm Mode list can be assigned a priority between 1 and 4294967295 with 1 being the
highest priority. The default value is 0 and indicates No Priority
Control MGMT Notification Destination
Enable/Disable notifications to the chosen SNMP destinations.
Control I/O
This will allow operators to view and change the status of the contacts manually for testing. Please note that
Decoder Data Process needs to be switched to OFF. (Support depends on the device configuration).
Control ACMM
View and enter the Trigger PID parameters and the PID, IP address and corresponding port for each of
the XD packet streams received by your Star receiver. Do not change these parameters without
consulting your Service Operator.
ENABLE /DISABLE: Enable/Disable participation in network-wide trigger activation.
Note: Allow or prevent triggering of receiver by head end regardless of channel being played.
TRIGGER PID: PID containing trigger list.
S T A R G e n 2 R e c e i v e r U s e r ’ s G u i d e
Page 19 of 47
Alarm
The following settings are available in the ALARM submenus:
MODE
: OFF
=
Warning and Alarm are switched off.
: Warning Only
Upon an error condition the Warning light on the front
will be activated.
: Warning+RelayA
Upon an error condition, after the warning delay period
has passed, the Warning light on the front panel will
illuminate. It will remain illuminated until the alarm delay
period has passed, at which point the Warning LED will
turn off, the Alarm Led will flash red and relay A will
become active.
: Warning+RelayB
Upon an error condition, after the warning delay period
has passed, the Warning light on the front panel will
illuminate. It will remain illuminated until the alarm delay
period has passed, at which point the Warning LED will
turn off, the Alarm Led will flash red and relay B will
become active.
: Warning+RelayC
Upon an error condition after the warning delay period
has passed, the Warning light on the front panel will
illuminate. It will remain illuminated until the alarm delay
period has passed, at which point the Warning LED will
turn off, the Alarm Led will flash red and relay C will
become active.
S T A R G e n 2 R e c e i v e r U s e r ’ s G u i d e
Page 20 of 47
LEVEL
Not present for all parameters. When present it is
programmable between the limits revealed when you
hover your mouse over the Level field.
W- DELAY
Delay in seconds before the warning light will be activated.
A- DELAY
Delay in seconds before the alarm light and relay will be
activated.
Note: to receive an alarm on the relay outputs, the alarms must be properly configured.
1. Warning Delay (W-DELAY) is programmable between 0 and 599 seconds.
2. Alarm Delay (A-DELAY) is programmable between 1 and 600 seconds.
The warning-delay should always be less than the alarm-delay. When a warning-delay is entered which is larger
than the alarm-delay, the alarm-delay will automatically be set to the warning-delay-time + 1 second.
It is good practice to disable Alarms for items that do not need to be monitored. For example, if you are using
IP- IN and are not connected to a Satellite feed, then disable the SAT- IN related alarms.
Alarm Menus and Sub Menus
Shows information about and allows setting of the alarms for input and audio levels including backup and
data. The alarm information can also be printed. Three sub-menus with multiple sub-menus contain the
information:
INPUT: the ASI- IN, SAT- IN or IP- IN parameters.
DECODER: the PSI, AUDIO, BACKUP and DATA parameters for all channels.
PMR: the Recording and Playback parameters for the PMR.
The Alarm mode contains multiple pull down menus for selection of the item to monitor.
After selection, in the EDIT mode, each selected item (MODE, LEVEL, WARNING DELAY and ALARM
DELAY) can be independently set (see examples below). Hover over a field underlined “…………” to see the
valid range. Individually alarmed items (RF LOCK, POWER etc.,) on a page can be saved individually or the
page can be completed then saved.
S T A R G e n 2 R e c e i v e r U s e r ’ s G u i d e
Page 21 of 47
With the mouse cursor in the editable field, an information field will pop up with the value limits:
Status
Information about the input and audio levels and the status information can also be printed. Five
submenus contain the information:
INPUT: the ASI- IN, Satellite SAT- IN and IP- IN parameters:
S T A R G e n 2 R e c e i v e r U s e r ’ s G u i d e
Page 22 of 47
DECODER: the source indication with Transport Stream info, four channels of audio with the
left/right dynamic level and the selected service. Transport Stream and RTP/IP audio show their
respective data rates if used as the input.
INPUT: shows the live source.
TRANSPORT STREAM: shows the data rate; Network name or “- - -“, if unavailable.
MEMORY SLOT: shows the presence or absence of the SD memory card.
Note: Audio files for backup can be written to the root directory of the SD card using a PC.
The file used by each decoder can be chosen on page DECODER>BACKUP>Channel x.
Warning: Before removing the SD card, all write access must be halted. If you can accept a
break in service, alter the INPUT>SAT-IN>Carrier Frequency to cause an Out of Lock
condition and then remove the card. If a break in service is not possible, contact your
Service Provider for a quiet time when no write accesses are planned.
Failure to do this may prevent proper operation of both triggers and the audio backup
CHANNEL x Audio:
AUDIO: shows Service type, SID, and BACKUP type
CONTACTS: shows relay contacts as “C” Closed or “O” open, L to R; 1 to 10
BACKUP PLAYLIST: shows as AVAILABLE if the default audio file “audiox.mp3” (or an
alternative as specified on page DECODER>BACKUP>Channel x) is present on the SD Card.
MPEG TS over IP; RTP/IP audio show their respective data rates or NOT AVAILABLE,
INTERNET SERVICE shows as AVAILABLE/NOT AVAILABLE
S T A R G e n 2 R e c e i v e r U s e r ’ s G u i d e
Page 24 of 47
NETMANAGER: indicates if the receiver is connected to a Network Command Channel (NCC)
and the date and time when this receiver last accepted a valid set of NCC-commands. To
operate correctly, the NCC PID must be included in the DVB-TS>PID List.
DEVICE CONFIG: shows all device specific information:
S T A R G e n 2 R e c e i v e r U s e r ’ s G u i d e
Page 25 of 47
Utility
There are 9 submenus: CLOCK, CLEAR LOG, PRINT SETTINGS, DEFAULT SETTINGS,
IMPORT/EXPORT, FORMAT SD CARD, SCHEDULE, TRIGGER, INSTALL OPTIONS, UPDATE
FIRMWARE & REBOOT DEVICE.
CLOCK: The unit clock can be switched on. The clock can be set Manualy; synchronized with the
NTP or with SNTP over the management LAN. To use NTP, the NTP PID must be configured in
the DVB-TS PID List. The IP address/Port for the SNTP server and the refresh interval can be
configured in the menu CONTROL>MGMT IP.
CLEAR LOG: The log file can be cleared.
PRINT SETTINGS: The complete settings of the unit can be printed in one overview.
DEFAULT SETTINGS: The default settings can be loaded.
Warning: Loading the default settings reboots the receiver resulting in IP service downtime. The
settings of the LINK, TCP/IP and NAME group of CONTROL IP TCP/IP will not be reset to the default
value in order to be able to reconnect to the device again.
IMPORT/EXPORT: All settings of this unit can be exported in a file (binary format) to a selectable
location and a user editable filename. The same settings file can be imported as well, to make an
easy copy possible. When imported, a tickbox can be selected to choose if the IP settings and
Identity have to be excluded.
FORMAT SD CARD: Erase all files on the card and refresh the file structure. Equivalent to a
disk format. All content files are lost.
SCHEDULE: A channel can be recorded and the recording played back anytime within 24 hours
of the recording start time on the decoder of choice using the Time Shift option. For longer
playback delays, or multiple playbacks of the same recording use the Date and Time option. The
Reports option allows viewing or printing of all recorded events and playbacks with complete
status information. The use of the Schedule tab is fully explained in the Advanced Topics
section.
TRIGGER: A decoder or All Decoders can be selected. A full list of all utility triggers can be
viewed from the All Decoders page or by using the View the full List for ALL decoders radio
button on any decoder trigger page. No triggers can be fired from the full list page; triggers can
be selected from a list of available triggers loaded by the head end and fired on the specific
decoder page only.
S T A R G e n 2 R e c e i v e r U s e r ’ s G u i d e
Page 26 of 47
In the capture below, trigger 20035 is missing one or more content files as shown by the red blocking.
Selecting the trigger and clicking “Show Details” reveals which file (or files) is missing. If this trigger is
fired, the missing file will be skipped over, regardless of its position in the Playlist.
S T A R G e n 2 R e c e i v e r U s e r ’ s G u i d e
Page 27 of 47
Timed Playlists (e.g. 20037) can not be triggered. Attempting to fire the trigger will give an error
message. The fields revealed by the Show Details button are explained below:
EARLIEST VALID: The earliest date on which the action becomes valid.
EXPIRY: The latest date on which this action may be commenced. May show “Does not expire”.
FADE (TYPE ,TIME): The type and duration of the fading used. (X-fade, V-fade or ½ fade).
REPEAT: If this trigger is to be repeated.
RECURRENCE: The days of the week within the Earliest Valid up to the Expiry date on which
this action will be valid.
START METHOD: How the action is commenced.
ELEM ID: Internally allocated reference.
S T A R G e n 2 R e c e i v e r U s e r ’ s G u i d e
Page 28 of 47
ACTION: What the receiver will do when the action is triggered.
INSTALL OPTIONS: In this section all options can be activated or de-activated with code from an
.xml file.
UPDATE FIRMWARE: Firmware can be uploaded from any accessible location and will result in
service downtime.
REBOOT DEVICE: This will trigger a reboot of the device, which will result in a service
downtime. The unit will start up again with the last saved settings.
Logout
You will be asked to confirm your log out.
S T A R G e n 2 R e c e i v e r U s e r ’ s G u i d e
Page 29 of 47
Advanced Topics
Using your PMR
The PMR capabilities of the Star 4 G2 audio receiver are subject to license restrictions and these pages and
option tabs will not appear in your receiver unless properly licensed. To see which options are installed on your
unit go to STATUS>DEVICE CONFIG and look under Device Options at the bottom of the page.
Time Shifting
Time shifting allows programming to be recorded and played back at a later time within the next 24 hours. To
create a Time shift event go to UTILITY>Schedule>Time Shift and click the Add button to open up a new event
line in the schedule (see below). Complete the entries for Days of the Week; Start and Stop time; Channel to be
recorded, Name, up to 16 characters (if required) and Data PIDs. This specifies the programming that will be
recorded.
To setup the playback, chose a playback time and decoder for the playback and click the disc symbol
to
save the entry. Up to 20 such Time Shift events can be created.
NOTE:
Recordings may not overlap
The minimum time shift is 10 seconds and the maximum 24hours (from the recording start time).
If the entered playback time is less than the recording time, playback will be on the following day.
Playback start time uses receiver time.
Recording can be set as disabled until required.
Only one playback is allowed per recording.
Simultaneous playback of two programs on one decoder is not allowed.
S T A R G e n 2 R e c e i v e r U s e r ’ s G u i d e
Page 30 of 47
Your receiver responds normally to triggers received during playback except for channel changes
which are ignored.
Time Shifted recordings are deleted within 24 hours of their playback. This deletes the recording
schedule, the playback schedule and their associated recording files.
The schedule may be printed out using the print button.
The event can be edited
or deleted
using the appropriate buttons. For the rules governing the editing
of recordings and playbacks see FAQ – “Why can I not always edit active time shift recording or playbacks?”
Using Date and Time
Date and Time shifting allows programming to be recorded and played back at a later date and time. To create
a Date and Time shift event goto UTILITY>Schedule>Date & Time and click the Add button to open up a new
event line in the schedule (see below). Complete the entries for Date; Start and Stop time; Channel to be
recorded, Name, up to 16 characters (if required) and Data PIDs. This specifies the programming that will be
recorded.
To setup the playback, chose a playback date, time and decoder for the playback and click the
symbol to
save the entry. Each recording can support up to five playback schedules. Up to 20 such Date and Time Shift
events can be created.
Recordings may not overlap
The minimum time shift is 10 seconds (from the recording start time).
Playback start time uses receiver time.
Recording can be set as disabled until required
Up to five playbacks are allowed per recording.
Simultaneous playback of two programs on one decoder is not allowed.
Your receiver responds normally to triggers received during playback except for channel changes
which are ignored.
Date and Time Shifted recordings and playbacks must be deleted by the user. This deletes the
recording schedule, the playback schedule and their associated recording files.
The schedule may be printed out using the print button.
The recording and playback events can be separately edited
or deleted
. For the rules governing the
editing of recordings and playbacks see “Why can I not always edit active time shift recording or playbacks?” in
the FAQ section.
S T A R G e n 2 R e c e i v e r U s e r ’ s G u i d e
Page 31 of 47
Recording and Playback Reports
The status of recordings and playbacks can be explored under the UTILITY>Schedule>Reports tab. Up to 100
scheduled recordings and playbacks are shown beginning 7 days prior to today’s date. The report can be
sorted on any column, and shows the status of each recording and playback as one of:
o
Recording Status
OK (recording complete, no alarms or warnings)
Warning
Alarm
in progress (recording active without warning or alarm)
no status (recording has not started yet)
o
Playback Status
OK (playback complete, no alarms or warnings)
Warning
Alarm
in progress (playback active without warning or alarm)
no status (playback has not started yet)
Click the individual status to open a detailed window for that event (see above) showing the Time into Recording
or Playback, Time left in Recording or Playback, the total Missed Audio and the 10 largest audio outages, their
time and duration.
The report page size can be selected and the selected page printed using the Print button. Multiple prints may
be required to print the complete report.
S T A R G e n 2 R e c e i v e r U s e r ’ s G u i d e
Page 32 of 47
GUI Tips
Finding extra Help
On many Web pages, hovering your mouse pointer over the information button
will produce extra
information related to the parameter:
Drop down Menus
In several menus, drop down sub-menus are available to help in selecting a value.
Valid numeric Ranges
In other cases a value can be set in an edit field shown as “…………………….” (the valid range is shown if you
hover over the field with the mouse pointer).
Text in Red
When saving a change, if the GUI refreshes with the change shown in red the changes were not made. An
explanation bar will appear with specific details of the error.
S T A R G e n 2 R e c e i v e r U s e r ’ s G u i d e
Page 33 of 47
FAQ’s
Why are there periods of silence in my playback?
If a signal loss occurs during recording (for example due to a loss of signal, a reboot or a loss of data)
then silence is played out for the periods where no audio frames were available.
If a reboot occurs during playback what happens to the playback?
A reboot during a playback of a file results in silence being played out for the duration of the reboot and then the
original file playout restarts at the same point in time as if it had continued to play during the outage and
terminates at the original expected time.
Why can I not always edit active time shift recording or playbacks?
To maintain the integrity of both content and output playbacks some restrictions are placed on editing and
deletion actions as follows:
Recording is active
o
Do not allow
Recording edits
o
Allow
Playback edits
Deletes (issue a warning prompt, playback stops and content deleted)
Playback is active
o
Do not allow
Recording edits
Playback edits
o
Allow
Deletes (issue a warning prompt, playback stops and content deleted).
I changed my SD card; do I lose all the recording and playback schedules?
No, when you change an SD card, you keep both the recording and playback schedules, but all content
recorded on the original SD card is lost.
How many recordings can I store?
Up to 20 Time shift and 20 Date and Time shift recordings can be stored by your Star receiver.
Can I take information off the receiver?
Yes, two methods of extracting data are available on your STAR G2 receiver: The Time Shift, Date and Time,
and the Reports screen all feature a Print button, allowing the page content to be sent to a printer connected to
your PC. Secondly, the Syslog file, sent to the Syslog server at the address specified in Control>Management
IP>Syslog contains additional information.
If a playback is interrupted, what will happen?
If a playback on a decoder is interrupted by another playback, the last playback takes precedence and
the playback terminates at the end of the interrupting playback, even if the end of the original playback
was later.
S T A R G e n 2 R e c e i v e r U s e r ’ s G u i d e
Page 34 of 47
If a playback is interrupted by a channel change, timed playlist, local activation of triggers on
a decoder, the playback shall stop and the live channel will take precedence.
How many playbacks can I add to a scheduled event?
For a time shifted event only 1 playback is allowed. For a Date and Time shifted event up to 5 playbacks can be
added. A warning is given if this number is exceeded.
How long does the recording and playback information stay on the receiver?
Playback and the associated recording status information remains on the Utility>Schedule>Report page of the
receiver for a period starting 7 days before the present and lasting for 7 days from today up to a maximum of
100 entries.
What happens to recordings over Daylight Savings Time changes and on a
leap year?
The recording last the entire demanded duration regardless of leap year and daylights savings time and
will playback for the exact period of time recorded (+/- 250ms).
The Warning LED is illuminated, what does this mean?
The Warning (Orange) LED illuminates for interrupted record and playback warning conditions:
Warning RECORDING conditions occur when:
o
Missing audio frames received greater than 1 second (i.e. no lock, RF
interference, no TS input)
o
The receiver is not powered at start time
Warning state occurs after power up
o
The receiver reboots during recording
Warning state occurs after power up
Warning PLAYBACK conditions occur when:
o
The decoder channel change occurs during playback
o
The receiver is not powered at start time
Warning state occurs after power up
o
The receiver reboots during recording
Warning state occurs after power up
When a recording or playback warning condition takes place:
o
A Warning log entry will be created
o
The Warning LED will be activated (if programmed)
o
The Warning LED remains on for the period of the recording or playback
The Alarm LED is showing, what does this mean?
The Alarm (Red) LED shows for interrupted record and playback alarm conditions:
Alarm RECORDING conditions occur when:
o
Recording channel does not exist at start time
o
No SD card available during recording (at start and during recording)
o
No more space is available on SD card.
Alarm PLAYBACK conditions occur when:
S T A R G e n 2 R e c e i v e r U s e r ’ s G u i d e
Page 35 of 47
o
Content is unavailable (i.e.no SD card, content deleted).
When an alarm condition takes place the following occurs:
o
Playback or recording is aborted
o
Alarm log entry is created
o
Alarm LED is activated (if programmed)
o
Alarm LED remains active for the period of the recording or playback
o
Alarm Relay is activated (if programmed)
o
Alarm Relay remains active for the period of the recording or playback.
S T A R G e n 2 R e c e i v e r U s e r ’ s G u i d e
Page 36 of 47
Remote control by SNMP
SNMP is the abbreviation for “Simple Network Management Protocol”. It is connected over the Monitor &
Control LAN connector at the rear of the unit. To have a list of all functions supported in this device, a MIB
file is available on request.
Remote control is based upon different types of messages: GET, SET, TRAPS, INFORMS etc. To
define further communication between the STAR and other SNMP devices/applications, a package with
MIB files is made available on request. Included in the MIB package is an application note describing all
available settings.
Please note that all SNMP connection related settings are available in the CONTROL/MGMT/IP and
CONTROL/MGMT/NOTIFICATION menus.
The STAR supports SNMP v1 TRAPS, SNMP v2c TRAPS and SNMP v2c INFORMS.
STAR default community names are:
GET=”usr_read_access”
SET=”usr_write_access”
The community names are configurable in the CONTROL>MGMT>NOTIFICATION>DESTINATION
menu.
Note: None of the CONTROL>MGMT>IP settings are available on the SNMP tree, as each
setting would cause a re-boot. Set these parameters through the GUI and save as a page once
only.
S T A R G e n 2 R e c e i v e r U s e r ’ s G u i d e
Page 37 of 47
Connector Specifications
Alarm output connector
9-pole Sub-D female connector
Pin
Description
1
Relay A common
2
Relay A normally open
3
Relay B normally closed
4
Relay C common
5
Relay C normally open
6
Relay A normally closed
7
Relay B common
8
Relay B normally open
9
Relay C normally closed
Audio output connector (per channel)
Relay connector (per channel)
9-pole Sub-D male connector
15-pole male connector
Pin
Description
Pin
Description
1
Analog Left Out +
1
Reserved (future RS-232 Data
out)
2
Analog Ground
2
Relay 1 NO
3
AES +
3
Relay 2 NO
4
Analog Ground
4
Relay 3 NO
5
Analog Right Out +
5
Relay 4 NO
6
Analog Left Out -
6
Ground
7
Analog Ground
7
Relay 5 NO
8
AES -
8
Relay 6 NO
9
Analog Right Out -
9
TX data Out (RS-232 Data Out)
10
Common
11
Common
RS232 comm connector
12
Relay 7 NO
13
Relay 8 NO
9-pole Sub-D female connector
14
Relay 9 NO
Pin
Description
15
Relay 10 NO
1
DCD
2
RX (In)
ASI Connector (Option)
3
TX (Out
5
DTR
75 Ohm BNC Female
6
Ground
7
RTS
8
CTS
9
RI
Normally closed is the switch status
when AC power is not connected or
when power is connected and the
alarm status is activated.
S T A R G e n 2 R e c e i v e r U s e r ’ s G u i d e
Page 38 of 47
Keypad Control
Measurement Displays
Press the ◄/► keys to navigate through these measurement displays:
Press the ▲/▼ (up down) or enter key to show the Settings menu display mode.
Superflex PA
Booting OS...
Initializing...
C/N(dB) EbNo(dB)
13,5 13,2
PWR(dBm) BER
-62 <1.0E-7
FE(kHz) CARRIER
-67 A
MGMT IP Address
10.0.1.14
CH1[audio vu bar
-30 -9 -3 0
CH2[audio vu bar
-30 -9 -3 0
NCC LAST UPD
NO NO SYNC
CH4[audio vu bar
-30 -9 -3 0
CH3[audio vu bar
-30 -9 -3 0
CH1 CH2 CH3 CH4
[▄ ][▄ ][▄ ][▄ ]
S T A R G e n 2 R e c e i v e r U s e r ’ s G u i d e
Page 39 of 47
Settings Menu Flowchart
Grey shows Optional or Special Order Item
1 IDENTITY Control Mode
LOCAL / REMOTE
Device Type
STAR G2
Version
V002
Serial
XXXX
Mgmt LAN MAC
Data LAN MAC
2 INPUT
2.1 SAT-IN
2.1.1 LNB
Mode
2.1.2 RF-IN
Preferred
2.1.3 CARRIER A
2.1.4 CARRIER B
Polarization
Frequency (kHz)
Mode
Rate (sym/s)
NCC PID
2.2 IP-IN
2.2.1 LOCAL PORT
Mode
IP Address
MAC Address
2.2.2 INPUT STRE
IP Address
UDP Port
2.3 ASI-IN
3 DVB-TS
3.1 STREAM
Input
SAT-IN / IP-IN
3.2 PID LIST
3.2.1 PID1
3.2.2 PID2
3.2.3 PID3
3.2.4 PID4
3.2.5 PID5
3.2.6 PID6
3.2.7 PID7
3.2.8 PID8
Mode
MPE PID
S T A R G e n 2 R e c e i v e r U s e r ’ s G u i d e
Page 40 of 47
3.3 FLEXKEY
IP Address
UDP Port
4 DECODER
4.1 AUDIO
4.1.1 CHANNEL 1
4.1.2 CHANNEL 2
4.1.3 CHANNEL 3
4.1.4 CHANNEL 4
Stream
Mode
Service
15KHz Lowpass
Gain
Stereo/Mono
Delay
Limiter
4.2 BACKUP
4.2.1 CHANNEL 1
4.2.2 CHANNEL 2
4.2.3 CHANNEL 3
4.2.4 CHANNEL 4
Enabled
Priority
4.3 DATA
4.3.1 CHANNEL 1A
4.3.2 CHANNEL 1B
4.3.3 CHANNEL 2A
4.3.4 CHANNEL 2B
4.3.5 CHANNEL 3A
4.3.6 CHANNEL 3B
4.3.7 CHANNEL 4A
4.3.8 CHANNEL 4B
Mode
Format
IRT/J.52
Process
Process only in
Baud
PES mode
5. OUTPUT
5.1 IP-OUT
5.1.1 Local Port Mode
IP Address
MAC Address
5.1.2 Output Str Enable
6 CONTROL
6.1 MGMT
IP Mode
IP Link
IP Static Addr.
IP Subnet Mask
IP Gateway
S T A R G e n 2 R e c e i v e r U s e r ’ s G u i d e
Page 41 of 47
WEB Enabled
SNMP Enabled
Syslog Srv. Add.
6.2 IO
6.2.1 CHANNEL 1
6.2.2 CHANNEL 2
6.2.3 CHANNEL 3
6.2.4 CHANNEL 4
CONTACT 1
CONTACT 2
CONTACT 3
CONTACT 4
CONTACT 5
CONTACT 6
CONTACT 7
CONTACT 8
CONTACT 9
CONTACT 10
6.3 ACMM
6.3.1 TRIG PID
Enable
PID
7 ALARM
7.1 INPUT
7.1.1 SAT-IN
7.1.1.1 RF-Lock
Mode
Warning Delay(s)
Alarm Delay (s)
7.1.1.2 POWER
Mode
Level (dBm)
Warning Delay(s)
Alarm Delay (s)
If BER alarm
7.1.1.3 BER
Mode
is set active,
Level Mantissa
all audio will
Level Exponent
be muted.
Warning Delay(s)
Alarm Delay (s)
7.1.1.4 C/N
Mode
Level (dB)
Warning Delay(s)
Alarm Delay (s)
7.1.1.5 Eb/No
Mode
Level (dB)
Warning Delay(s)
S T A R G e n 2 R e c e i v e r U s e r ’ s G u i d e
Page 42 of 47
Alarm Delay (s)
7.1.1.6 TS
Mode
Warning Delay(s)
Alarm Delay (s)
7.1.2 IP-IN
Mode
Warning Delay(s)
Alarm Delay (s)
7.2 DECODER
7.2.1 PSI
Mode
Warning Delay(s)
Alarm Delay (s)
MODE; WARNING DELAY & ALARM DELAY are settable for 7.2.2 Audio, 7.2.3 Backup and 7.2.4 Data
items. LEVEL is also settable for Audio LEFT, RIGHT and L+R
7.2.2 AUDIO
7.2.2.1 CH 1
7.2.2.2 CH 2
7.2.2.3 CH 3
7.2.2.4 CH 4
7.2.2.1.1 LEFT
7.2.2.1.2 RIGHT
7.2.2.1.3 L+R
7.2.2.1.4 STREAM
7.2.3 BACKUP
7.2.3.1 CH 1
7.2.3.2 CH 2
7.2.3.3 CH 3
7.2.3.4 CH 4
7.2.3.4.1 MPEGTS
7.2.3.4.2 RTP/IP
7.2.4 DATA
7.2.4.1 CH 1A
7.2.4.2 CH 1B
7.2.4.3 CH 2A
7.2.4.4 CH 2B
7.2.4.5 CH 3A
7.2.4.6 CH 3A
7.2.4.7 CH 4A
7.2.4.8 CH 4B
7.2.4.1.1 T.OUT
7.2.4.1.2 O.FLOW
S T A R G e n 2 R e c e i v e r U s e r ’ s G u i d e
Page 43 of 47
8 STATUS
8.1 CONFIG
Device Firmware
Device Decoder
NCC Address
8.2 XD LICENSE GLOBAL
Decoder1
Decoder2
Decoder3
Decoder4
Net ID
Site ID
Expiry Date
Class ID
Serv. Prod.
8.3 OPTIONS
VLSR
MPEG4
LIMITER
ACMM
8.4 SPECIALS
----
10 Phones
Channel Select
Level (dB)
11 Display Contrast
Backlight
Backl. Timeout
PID Editmode
S T A R G e n 2 R e c e i v e r U s e r ’ s G u i d e
Page 45 of 47
WEEE Disposal Instructions
Disposal Instructions
Do not dispose of this device with unsorted household waste.
Improper disposal may be harmful to the environment and human health.
Please refer to your local waste authority for information on return and collection systems in your area.
Directives de mise au rebut
Ne mettez pas cet appareil au rebut avec les déchets ménagers non triés.
La mise au rebut incorrecte peut être nocive à l’environnement et à la santé humaine.
Veuillez vous renseigner auprès des autorités compétentes de votre localité sur les procédures de renvoi
et de collecte dans votre région.
Instruzioni per lo smaltimento
Smaltire questo dispositivo solo in un contenitore previsto per la raccolta municipale di rifiuti separata.
Uno smaltimento improprio può inquinare l’ambiente ed essere pericoloso per la salute delle persone. Per
informazioni sui centre di raccolta locali rivolgersi alle autorità locali competenti per lo smaltimento dei
rifiuti.
Instruções de disposição
Não disponha a eliminação deste dispositivo como resíduo municipal não classificado.
Disposição imprópria pode ser danosa ao meio-ambiente a à saúde de seres humanos. Por gentileza
consulte a sua autoridade local de eliminação de resíduos para informações sobre os sistemas de
retorno e coleta na sua área.
Instrucciones de deshecho
No tire este dispositivo en los contenedores municipales de basura no clasificados para reciclaje. Tirar
residuos inapropia-damente puede resultar nocivo para el medio ambiente y para la salud de las
personas. Por favor diríjase a las autoridades locales responsables de la eliminación de residuos para
obtener información sobre los sistemas de devolución y recolección en su área.
Anweisungen für die Entsorgung
Dieses Gerät darf nicht mit unsortiertem Hausmüll entsorgt werden. Eine unangemessene Entsorgung
kann sich schädlich auf die Umwelt und die Gesundheid auswirken. Bitte beachten Sie die Hinweise der
für Ihren Ort zuständigen Behörden zu Rückgabe und Sammelverfahren.
To whom it may concern:
International Datacasting EMEA has done its utmost best to design and manufacture the family of STAR
receivers in compliance to the latest current standards with the least environmental impact. They are a 100%
RoHS free product, they are designed as “Green” (low power) and they are tested against and in compliance
with FCC regulations and CE approvals.
Arnhem, July 18th, 2012
F. Peters-Sengers,
Managing Director IDC EMEA
S T A R G e n 2 R e c e i v e r U s e r ’ s G u i d e
Page 46 of 47
Warranty & Service Information
International Datacasting Corporation (Seller) warrants the items manufactured and sold by the Seller to be free of
defects in material and workmanship for a period of one (1) year from date of shipment to the original purchaser.
International Datacasting agrees to repair or replace the product, at no charge, within the warranty period, providing
the product is delivered to IDC in its original packaging or equivalent, fully insured and with all shipping charges pre-
paid.
To honor this warranty and to ensure the best possible service to you, IDC requires the following information to be
included with the returned product:
o
A detailed description of the problem and when it occurs;
o
The model and serial number of the unit.
o
A copy of the original invoice for the product
o
Specify “Made In Canada” on your paper work
o
An RMA number obtained prior to the return of the unit clearly printed on the exterior of your shipping
container. To obtain an RMA number, log on to www.datacast.com and follow the link at the top of the page
to “RMA Submission”.
The following are expressly NOT COVERED under warranty. Any loss, damage and/or malfunction relating in any
way to shipping, storage, accident, abuse, alteration, misuse, neglect, failure to use products under normal operating
conditions, failure to use products according to any operating instructions provided by the Seller, lack of routine care
and maintenance as indicated in any operating maintenance instructions, or failure to use or take any proper
precautions under the circumstances.
This warranty is expressly in lieu of and excludes all other expressed and implied warranties, including but not limited
to warranties of merchantability and of fitness for particular purpose, use or applications, and all other obligations or
liabilities on the part of the Seller, unless such other warranties, obligations or liabilities are expressly agreed upon to
in writing by the Seller. All obligations of the Seller under this warranty shall cease in the event of its products or
parts thereof have been subject to accident, abuse, alteration, misuse or neglect, or which have not been operated
and maintained in accordance with proper operating instructions. In no event shall the Seller be liable for incidental,
consequential, special or resulting loss or damage of any kind howsoever caused. The Seller’s responsibility for
damages shall not exceed the payment, if any, received by the Seller for the unit or product or service furnished or to
be furnished, as the case may be, which is the subject of claim or dispute.
If you have determined that the unit is malfunctioning, DO NOT ATTEMPT TO ALTER OR REPAIR THE UNIT.
Please contact either your Network Service Provider or IDC at www.datacast.com/customer-service/rma-sumbission.
International Datacasting Corporation
50 Frank Nighbor Place, Kanata, Ontario K2V 1B9 Canada
Attn: Customer Service
Tel: 613-596-4120 | Fax: 613-596-9208
Email: [email protected]
S T A R G e n 2 R e c e i v e r U s e r ’ s G u i d e
Page 47 of 47
STAR Gen 2 User’s Guide
International Datacasting Corporation Part No. 92087070-50
This product (“Product”) from International Datacasting Corporation (IDC) contains software (including firmware)
origination from IDC and its suppliers and may also contain software from the open source community.
Software components from the open source community included in IDC products are covered by license terms
identified at www.datacast.com By using the software, you or the entity or company you represent (“You”)
acknowledge that You have reviewed such license terms and that You agree to be bound by the terms of such
licenses. Where such specific license terms entitle you to the source code of such software, that source code is
available on request at cost from IDC for at least three years from the purchase date of this product.
For additional information on open source software in IDC products please visit the IDC website at:
www.datacast.com
If you would like a copy of the GPL or certain other open source software source code in this Software (if provided for
in the applicable license) on a CD, IDC will mail to you a CD, with such code for U.S. $9.99 plus the cost of shipping,
upon request.
International Datacasting Corporation (TSX: IDC) is a global leader in digital content distribution for the world’s
premiere broadcasters in radio, television and digital cinema. IDC offers a broad portfolio of advanced solutions
including Pro Audio, Pro Video, Pro Cinema and Pro Data for implementing broadcast content contribution and
distribution applications. IDC’s solutions are in demand for radio and television networks, digital cinema, 3D live
events, satellite news gathering, sports contribution, and IPTV among others. IDC is headquartered in Ottawa,
Canada, with regional offices in Arnhem, the Netherlands and in San Diego, California. IDC has installations in over
100 countries and service offices in Australia, Singapore and China with an international network of value-added
partners and distributors.
HEADQUARTERS: 50 Frank Nighbor Place, Kanata, ON Canada K2V 1B9
Tel: +1 613.596.4120
WEBSITE: www.datacast.com
EMAIL: [email protected]
SuperFlex® is a trademark of International Datacasting Corporation. All other trademarks are property of their
owners. Copyright © 2013-15 International Datacasting Corporation. Information in this document is subject to
change without notice.
