Johnson & Starley Reno HE30C User Instructions

Johnson & Starley www.johnsonandstarley.co.uk Model: HE30C GC No: 47-416-01 User’s Instructions Tel: 01604 762 881 Publication ZZ1184/1 Product Identification No: 87B 074

82 12 1.0 PRE- HEAT Temperature of the central heating flow. Pump is running. Pre-heat is selected. Anti-cycle feature is in operation Outside temperature, when OTC sensor is connected. Pressure in heating circuit Fan is running oC oC bar 65 Temperature of the domestic hot water Ignitor is sparking Summer mode Flame modulation Opentherm boiler management system is connected Error code oC ER88 : RESET

Power On/Off switch Domestic hot water control (P2) Reset button Central Heating water temperature control (P1) Preheat button View of user control panel Control PPanel The flip door at the bottom of the boiler is held in the closed posision by a concealed latch that has a push and release mechanism and is located on the upper edge of the door in the centre. To gain access to the control panel, apply light pressure on the upper edge of the flip door at the centre, the latch will then release allowing the door to drop into the open position. To close the flip door, swing it into the closed position and apply light pressure to the upper edge in the centre of the door and the latch mechanism will lock the door into place.

carry out the following steps: • Check that the electrical supply to the boiler is ON at the external isolator. • Ensure all hot taps are closed. • Set any remote controls as required. • Turn the CH and DHW controls to the minimum setting. Switch on the appliance at the on/off switch on the control panel. The boiler will then be in the STANDBY mode. • Check the heating system pres- sure displayed in the RH lower corner of the display. This should read at least 1.0 bar. A sealed pressurised system must be filled by a competent person. Only operate the boiler when you are sure that the system has been filled and pressurised. If you are in any doubt about the boiler being filled with water contact your installer. Operation oof CCentral Heating In order to turn on the central heating and adjust the temperature, turn the control knob P1 to the desired setting between off and max 82°C. When the control knob is turned the central heating water temperature will flash and indicate the new temperature setting. After a delay of 5 seconds the display will revert to a steady display of actual central heating water temperature. This will disappear if there is no central heating demand. During a central heating demand the radiator symbol and the central heating water temperature will be illuminated on the display. If central heating is not required for any extended period turn the control knob P1 fully anti-clockwise to the off position. In this position the “heating off “ symbol will be displayed, the domestic hot water and frost protec- tion will still be active. This is also the “summer mode”. Operation oof DDomestic Hot W Water The domestic hot water temperature is adjustable between 30°C and 65°C by the control knob P2. When the control knob is turned the DHW water temperature will flash and indicate the new temperature setting. After a delay of 5 seconds the dis- play will revert to a steady display of actual DHW temperature. This will disappear if there is no DHW demand. During a DHW demand, the tap symbol and the DHW temperature will be illuminated on the display. Pre-heat BButton With the pre-heat button selected the boiler is maintained in a hot condition to enable a fast response to any DHW demand. When selected, PRE-HEAT will be illuminated on the display. If required this can be selected for all year round use, but will be of maximum benefit in the summer months, or when there is little or no demand for central heating, in which case the boiler would become cold without the pre-heat button selected. The pre-heat function has a built-in intelligent function that will turn itself off if there is no DHW demand for a 24 hour period. If previously selected, once DHW water has been drawn off, the function will automatically re- enable. Reset BButton Should a fault occur this button can be pressed to reset the controls and initiate a new start up sequence.

times in any 4 minute period then the boiler will lockout and an error code will be displayed in the centre of the display. Pressing the reset will enable the boiler to relight. If the fault recurs, turn off the boiler and consult a CORGI registered installer. Boiler ooverheat In the event of the boiler overheating the boiler will lockout and an error code will be displayed in the centre of the display. Pressing the reset will enable the boiler to relight. If the fault recurs, turn off the boiler and consult a CORGI registered installer. Water SSystem PPressure The water system pressure is shown in the bottom right hand of the display. If the pressure drops below 1.0 bar it will begin to flash indicating the system needs to be topped up by a competent person. If the pressure continues to drop and reaches 0.6 bar, an error code will appear in the centre of the display and all heat demands will be blocked. This may indicate a leak and the system should be checked before being re-pressurised. Condensate DDrain The condensate drain must not be modified or blocked. Blockage of the condensate drain caused by debris or freezing, can cause the boiler to lockout. If freezing is suspected and the pipe run is accessible, then an attempt to free the obstruction by pouring hot water on to the pipe may be made. If this fails to remedy the problem, the assistance of a CORGI registered installer should be sought. Service aand M Maintenance It is recommended that a full mainte- nance check be carried out annually on the appliance. It is also recommended to take out a further service agreement on the expiry of the guarantee period. You can obtain further information on this from your gas supplier. The appliance should be checked /servicedby a CORGI registered installer. If you require service on your appliance please contact your local installer or gas supplier. On completion of the service the installer should fill in the service sec- tion at the rear of the BENCHMARK log book. All installers registered with CORGI carry an identification card. This card will have an ID number which should be recorded in your logbook. If you have any queries regarding your installer you can contact CORGI by telephone on 01256 372400. Escape oof GGas Should a gas leak be suspected contact your gas supplier with out delay. Do not search for leak with a naked flame. Cleaning tthe AAppliance The appliance casing should only be cleaned with a damp cloth then dried. Do not use abrasive or solvent cleaners. Error CCodes For any other error codes that you may encounter on your boiler, please refer to your Installation & Maintenance Instructions or contact your local CORGI registered installer. 1.0bar bar 0.9 ER:26 RESET ER:37 RESET ER:?? RESET ER:03 RESET

Setting the time • Rotate the dial clockwise, by hand, until the indicator arrow is pointing to the current time. Note the time is set in 24 hour format. Setting the central heating on and off times • Select the on times by pushing the black tappets to the outside. • Select the off times by pushing the black tappets to the inside Overriding the clock The clock has a manual on off switch which operates as follows 1 Heating on continuously Heating on timed 0 Heating off Indicator Arrow 1 0 Black Tappets Digital PProgrammer ((if ffitted) Button Description Time/Automatic Run mode selection Prog Programme selection Res. Reset clears all settings ON/OFF selection in Prog mode, Manual override selector in run mode +/-1h Summer/Winter time settings h Sets the hour m Sets the minute Day Sets days LCD DDisplay The LCD display incorporates a number of different elements to display vari- ous data and information Programmes The Digital Programmer will accept up to 20 events Each event consists of: • An ON or OFF command • Time of Day (hour and minute) • Single day or multiple days An event is required for each ON and OFF. NOTE: MULTIPLE ON OR OFF EVENTS MAY BE PRO- GRAMMED, SEE EXAMPLE. BEFORE PROCEEDING WITH SETTING THE TIME AND PROGRAMMING THE UNIT, PRESS THE RESET KEY TO CLEAR ALL DATA FROM THE MEMORY. Run mode: Off Continous off On Continous on 1 2 3 4 5 6 7 +1h AM 8 88 8 : Days of week Time of day Manual override on

key during the following: (If British summer time is in effect, press +/- 1h first) • Press h to advance the current hour (While holding down the key) • Press m to advance to the current minute (While hold- ing down the key) • Press DAY repeatedly to advance to current day (While holding down the key) Selecting AAM/PM oor 224 hhour cclock After pressing reset the display may show AM, numbered days will be flashing on and off. If the display does not show AM. It is in 24 hour mode, press and hold the h key and press the +/-1h key once. AM will appear in the display If display is in AM/PM mode and 24 hour time mode is desired, press and hold the h key, press the +/- key once Setting tthe TTime If the h and m keys are held down longer than 2 sec- onds, the numbers will advance rapidly. Day KKey SSelections Press Day Key Display shows Days 0 times 1234567 Every day 1 time 123456 mon-sat 2 times 12345 Mon-fri 3 times 67 sat & sun 4 times 1 Monday 5 times 2 Tuesday 6 times 3 Wednesday 7 times 4 Thursday 8 times 5 Friday 9 times 6 Saturday 10 times 7 Sunday Note: if the days are flashing, it indicates the day of the week was not set when setting the time. The timer cannot be programmed unless the day of the week is entered. Manual GGMT/BST ttime cchangeover Each year, in the spring press +/- 1h to advance the time an hour. In the Autumn press +/- 1h to set back an hour. Programming 224 hh oor 77 dday SSchedules It may be helpful to write out the programme schedules before beginning. Example Event 1: On at 7.00AM Monday through to Saturday Event 2: Off at 5.00PM Monday through to Friday Event 1: Off at 7.00PM Saturday Three events need to be entered. Event 1 (ON at 7:00AM Monday through Saturday) Press key once. ON symbol appears Press h key to 07AM Press m key once to 00 Press Day key once 123456 is displayed Press Prog key to enter Event 2 (Off at 5.00PM Monday through to Friday) Press key twice. Off symbol appears Press h key to 05PM Press m key once to 00 Press Day key twice 12345 is displayed Press Prog key to enter Event 3 (Off at 7.00PM Saturday) Press key twice. ON symbol appears Press h key to 07PM press m key once to 00 Press Day key 9 times 6 is displayed Press Prog key to enter Press key to enter run mode IF 24 HOUR TIME CONTROL (SAME SCHEDULE EVERY DAY OF THE WEEK) IS DESIRED IGNORE Day KEY. 1 2 3 4 5 6 7 AM - -- - : Event RReview To review the programs at any time, press Prog key. Events will appear in the order they were entered with repeated presses of the Prog key. After all events have been reviewed the display will go blank in order to allow you to enter another event. Another press of the Prog key will display the number of free events spaces. Manual OOverride While in the run mode, pressing the key will reverse the current mode i.e on to off or off to on. 1 2 3 4 5 6 7 +1h AM 8 88 8 : Time of day

www.johnsonandstarley.co.uk Tel: 01604 762 881 Continuous ooperation While in the run mode, press the key twice to turn the output to permanently on. The symbol appears in the display. To revert back to timed operation press the until the symbol appears in the display. Changing aan EEvent Select the event to be changed with the Prog key. A new set of days may be selected with Day key just as in initial programming. Hours and minutes can be changed with the h and m keys Press the Prog key to store the new programme. Troubleshooting Problem: days are flashing and pressing any key does nothing BUT key turns output ON and OFF. Solution: Time of Day and DAY of Week have not been set. This may occur if the power has been off to boiler for longer than 3 days. Problem: Time of day was set while holding the key down but the days are still flashing. Solution: Current day of the week has not been set. Problem: It is 10AM and an ON event for 8AM was entered but the output symbol is not ON. Display shows the and the symbols Solution: After programming the timer does not look back and will not take place until the event recurs at 8AM tomorrow. In order to turn the boiler ON use the manual override.