Marksman X6 Installation Manual

(1) This device may not cause harmful interference; and (2) This device must accept any interference received, including interference that may cause undesired operation. Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. For Technical Assistance, please call (800) 638-3600, or visit www.magnadyne.com

Installer Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Component Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Wiring Harness Quick Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 Wiring Starter and Power Harness Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7 Door Lock Output Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10 Accessory Alarm and Remote Start Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-15 Plug-In Harness Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-16 Transmitter Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Keyless Entry Feature Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-19 Remote Start Feature Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-21 Engine Crank Detection Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-23 Remote Start Shutdown Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Return to Factory Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-25 Safety Testing the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 2

professional installer. This remote start and alarm system is NOT a “Do It Yourself” product. • This remote starter and alarm system is designed to be installed on fuel injected gasoline or diesel vehicles with an automatic transmission ONLY. Installation of this system on a vehicle with a manual transmission (Stick Shift) is dangerous and is contrary to it’s intended use. • This system must be installed and wired through a safety switch so it will not start the engine while in any forward or reverse gear. This is normally accomplished by connecting the systems provided safety wire to the vehicles electronic Neutral Safety switch located on the transmission shifter. • Some automatic transmission vehicles may have a mechanical type park safety lock system instead of electrical safety switch. This mechanical type system does not interrupt the starter circuit when the transmission is any gear and does not offer the 100% level of safety required for remote starting purposes. The next best safety connection point on this type of vehicle would be the vehicle parking brake switch. This requires the user to set the parking brake prior to activating the remote starting system. • Once you install this system, you must verify that the vehicle will not start in any forward or reverse gear. Regardless of the type of vehicle. • Do not install any component near the brake, gas pedal or steering linkage. • Some vehicles have a factory installed transponder immobilizer system that can severely complicate the installation. There is a possibility that this system can not be installed on some immobilizer equipped vehicles. • Most vehicles have an SRS air bag system. Use extreme care and do not probe any wires of the SRS system. Disconnect the vehicle (+) or (-) battery cable before installing this system on the vehicle. • Use conventional crimp lock type connectors on all low current wiring connections. Poor wiring, i.e. taped joints, will introduce unreliability into the remote start and alarm system and may result in false alarms, incorrect or failed operation. • All wires that operate at currents higher than 10A should be soldered to insure a long lasting connection. • Install wiring neatly under carpets or behind trim to prevent possible damage to wires. • For dealer technical assistance, please call (800) 638-3600 or visit www.magnadyne.com Installer Warnings

• We suggest you mount it on the lower or upper left-hand side of the windshield. Warning! Do not mount in such a manner that it obstructs the driver’s view. • The receiver/antenna whip can be vertical or horizontal. 1. Remove the protective tape backing. 2. Carefully align the receiver/antenna and apply to windshield. 3. Route the black connecting cable behind the trim and connect to receiver/antenna. 4. Connect the other end to the control module. HC1 6-Pin Remote Start Harness Violet Remote Starter Output Red +12VDC Battery Input #2 Yellow +Ignition 1 Output Red +12VDC Battery Input #1 Brown +ACC / Heater-Air Conditioner Output Pink +Ignition 2 / ACC 2 Output 4 Component Placement Wiring Harness Quick Reference Valet Switch Select a mounting location for the switch that is easily accessible to the driver of the vehicle. The switch does not have to be concealed, however, concealing the switch is always recommended, as this provides an even higher level of security to the vehicle. Mount the valet switch in a hidden but accessible location. Route the valet switch wires to the control module. Mount the antenna horizontally for best reception.

Red/White Park Light Relay Input Black Chassis Ground Brown (-) Programmable Output (Horn - Default) White Parking Light Relay Output Red +12VDC Battery Input HC3 3-Pin Door Lock Harness Green (-) Lock Output Blue (-) Unlock Output 5 Wiring Harness Quick Reference Violet/White Tach Input Gray (-) Remote Start Hood Pin Safety Input Brown (+) Brake Switch Input Black/White (-) Neutral Safety Switch Input HC4 9-Pin Accessory Harness Pink (-) Ignition #3 Output White/Blue AUX Start and Turn Off Input White (-) Programmable Output (Dome Lt - Default) Red/White (-) Channel #3 Output (Trunk Release) Light Blue (-) Programmable Output (2nd Unlock Ouput)

The method that the remote starter uses to start the vehicle is a duplicate of the ignition switch function. Below, is an explanation of the 3 basic functions of the ignition switch. Since this installation will require analysis of the ignition switch functions, it is recommended that you make the three connections below at the ignition switch harness directly. Careful consideration for the connection of this wire must be made to prevent the vehicle from starting while in gear. Understanding the difference between a mechanical and an electrical Neutral Start Switch will allow you to properly identify the circuit and select the correct installation method. In addition you will realize why the connection of the safety wire is required for all mechanical switch configurations. WARNING! Failure to make this connection properly can result in personal injury and property damage. In all installations it is the responsibility of the installing technician to test the remote start unit and assure that the vehicle can not start via RF control in any gear selection other than park or neutral. In both mechanical and electrical neutral start switch configurations, the connection of the Violet wire will be made to the low current start solenoid wire of the ignition switch harness. This wire must have +12 volts when the ignition switch is turned to the “START” (crank) position only. This wire have 0 volts in all other ignition switch positions. Note: If a starter disable relay is installed, the connection of the violet wire must be at the starter side of the relay, not the ignition switch side. Failure to connect this wire to the ignition switch side of the neutral safety switch can result in personal injury and property damage (See Neutral Start Safety Test for further details). Remove the two 20A fuses prior to connecting these wires and do not replace them until the harness has been plugged into the control module. These wires are the source of current for all the circuits the relay harness will energize. They must be connected to a high current source. Connection to 12V battery terminal recommended. Connect the Yellow wire to the ignition 1 wire from the ignition switch. The ignition wire should receive +12 volts when the ignition key is in the “ON” or “RUN” and “START” or “CRANK” position. When the ignition is turned “OFF”, the ignition wire should receive “0” voltage. The yellow wire must be connected. "ACC" "START" "OFF" "ON" Starter Start Cut Relay (When Used) Violet Wire Closed in Park or Netral Only Neutral Safety Switch 6-Pin White Connector 6 Wiring Violet Wire: Starter Output Red Wires (2): +12V Power Input Yellow Wire: Ignition 1 Output

Some vehicles have 2 ignition wires that must be powered. Connect the “Pink” wire to the ignition 2 wire from the ignition switch. No connection required on vehicles without second ignition. Connect the Brown wire to the accessory wire that powers the climate control system. An accessory wire will show +12 volts when the ignition switch is turned to the “ACCESSORY” or “ON” and “RUN” positions, it will show 0 volts when the key is turned to the “OFF” and “START” or “CRANK” position. There will often be more than one accessory wire in the ignition harness. The correct accessory wire will power the vehicle’s climate control system. Some vehicles may have separate wires for the blower motor and the air conditioning compressor. In such cases, it will be necessary to add a relay to power the second accessory wire. HC2: White 5-Pin Power Harness The Red/White wire has already been assembled to work with a +12 volt switched parking light system (most vehicles). For vehicles with ground switched parking light activation cut this wire and connect it to ground. Connect the White wire to the parking light wire coming from the headlight switch. Do not connect the White wire to the dashboard lighting dimmer switch (damage to the dimmer will result). The limitation of the White wire is 10 amp maximum. Do not exceed this limit or damage to the alarm and parking relay will result. This is the main ground connection of the alarm module. Make this connection to a solid section of the vehicle chassis. Do not connect this wire to any existing ground wires supplied by the factory wire loom, make the connection to the vehicle’s chassis directly. By default, the Brown wire is the negative (-) output connection for the horn. Current capacity is 200mA. Make the connection to the horn relay trigger wire. Typically, this wire can be found at the steering column near the ignition switch. Some vehicle horn systems may be (-) trigger and a relay will need to be added for proper operation as shown. Option: (-) Factory Alarm Re-Arm Output (See “Alarm Feature Programming” to change this function) Connect this wire to the existing vehicle’s alarm ARM trigger wire. The “Red” wire supplies power to the system. Connect this wire to a constant +12 volt source. 87 87a 86 85 30 Brown Wire To Ground To Horn +12V or Ground Depending on System Requirements Fuse White 5-Pin Connector Wiring (continued) Pink Wire: Ignition 2 Output Brown Wire: Accessory Output, Heater/AC Output Red/White Stripe: Parking Light Relay Input White Wire: Parking Light Relay Output, + or - Selectable Black Wire: System Ground Brown Wire: (+) Programmable Output - Horn Default Setting Red Wire: System Power, +12V Constant

lock switch . If the door lock control system on the vehicle is not (-) type, locate the diagram enclosed that matches your application and follow that diagram. If the door lock control system on the vehicle is (-) type, connect the Green wire to the lock wire from the door lock switch . If the door lock control system on the vehicle is not (-) type, locate the diagram enclosed that matches your application and follow that diagram Green Wire: (-) Door Lock Control 8 HC3: Black 3-Pin Door Lock Harness Wiring (continued) Blue Wire: (-) Door Lock Control 3 Wire Ground Trigger Door Lock System (-) Lock Out Ground Input (-) Unlock Out To Door Lock Control Relays Lock Control Switch Blue Wire: Connect to Unlock Green Wire: Connect to Lock Black 3-Pin Mini Connector 3 Wire Positive Door Locking Systems 87 87A 85 86 30 87 87A 85 86 30 To +12 Volts (Battery +) Black 3-Pin Mini Connector Green Wire Blue Wire Note: ALA-DL1 relay pack can be used (+) Lock Out +12 Volts Input (+) Unlock Out Lock Control Switch To Factory Door Lock SYstem 5 Wire Ground at Rest Door Locking Systems 87 87A 85 86 30 87 87A 85 86 30 To +12 Volts (Battery +) To Power Lock Switch To Power Lock Motors White Wire: Lock Brown Wire: Unlock Green Wire: Lock Blue Wire: Unlock Violet Wire ALA-DL1 Relay Pack Red Wire: Lock Black Wire: Unlock Black 3-Pin Mini Connector Green Wire Blue Wire Note: Orange wire from ALA-DL1 must be connected to +12V

87 87A 85 86 30 87 87A 85 86 30 To +12 Volts (Battery +) To Ground To Newly Installed Power Door Lock Motors White Wire Brown Wire Green Wire: Lock Blue Wire: Unlock Violet Wire ALA-DL1 Relay Pack Red Wire: Lock Black Wire: Unlock Black 3-Pin Connector Green Wire Blue Wire Note: Orange wire from ALA-DL1 must be connected to +12V Wiring (continued) HC3: Black 3-Pin Door Lock Harness (continued) Unlock Driver's Door First for 3-Wire Negative Door Lock Systems Unlock Driver's Door 87 87A 85 86 30 Unlock Wire Passenger's Door Lock Unlock To +12V or Ground To +12V or Ground Driver's Door Rear Door Passenger's Door Switch Door Lock Relay Control Module Lock Unlock +12V ALA984H Relay Driver's Door Switch Cut Black 3-Pin Connector Light Blue Wire White 9-Pin Mini Connector Green Wire Blue Wire

87 87A 85 86 30 87 87A 85 86 30 To +12 Volts (Battery +) To Power Door Lock Switch Lock/ Unlock Wires Lock Unlock 87 87A 85 86 30 + Unlock Cut Driver's Door Motor White 9-Pin Mini Connector Light Blue Wire Black 3-Pin Mini Connector Green Wire Blue Wire Unlock Driver's Door First Wiring for 5-Wire Ground at Rest Door Locking Systems 87 87A 85 86 30 87 87A 85 86 30 To +12 Volts (Battery +) To Power Lock Switch To Power Lock Motors Lock Lock Unlock Unlock 87 87A 85 86 30 + Unlock Cut Driver's Door Motor White 9-Pin Mini Connector Light Blue Wire Black 3-Pin Mini Connector Green Wire Blue Wire 10 HC3: Black 3-Pin Door Lock Harness (continued) Wiring (continued) White Wire No Connection To Vehicles Lock/Unlock Wire Brown Wire No Connection Green Wire Lock Blue Wire Unlock Violet Wire To +12 Volts or Ground as Required Lock Fuse 1 Unlock Fuse 2 ALA-DL1 Red Wire Black Wire Black 3-Pin Mini Connector Green Wire Blue Wire Note: Orange wire from ALA-DL1 must be connected to +12V. Orange Wire +12 Volts One Wire Multiplexing Door Locking Systems Some vehicle’s use one wire to lock and unlock the doors. Some require 2 resistors, one for lock and one for unlock. We have developed patented plug-in fuse resistors for this application. Simply remove the fuse from the ALA-DL1 door lock module and replace with correct resistor value fuses that matches the vehicles door lock switch system. Wiring: 1. Connect both the green (lock) and the blue (unlock) wires to the vehicles one wire lock/unlock wire. 2. Connect the violet polarity input wire to +12v or to ground. To match vehicles door lock polarity. 3. The white and the brown wires will not be used.

This input provides the remote start system with information about the engine’s revolutions per minute (RPM). It can be connected to the negative side of the coil in vehicle with conventional coils. In multi-coil ignition system, the system can have individual coil wires. Individual coil wires in a multi-coil ignition system will register lower amounts of AC voltage. Common locations for a tachometer wire are the ignition coil itself, the back of the gauges, engine computers, and automatic transmission computers. Note: This wire requires programming (See “Remote Start Feature Programming” for the proper programming procedure). Important! Do not test tachometer wires with a test light or logic probe. Electronic components of the ignition system will be damaged. You must us a Digital Multi-meter. Note: If you use the voltage or timer checking method for remote start detection, this wire does not need to be connected. How to find a tachometer wire with your multi-meter: 1. Set the meter to read ACV or AC voltage (12 or 20V). 2. Attach the (-) probe of the meter to chassis ground. 3. Start the vehicle’s engine. 4. Probe the wire you suspect of being the tachometer wire with the red probe (+) of the meter. 5. If the probed wire is the correct wire, the meter will read between 1V and 6V at idle and will increase with RPM. The Black/White wire is a safety input wire. The remote start unit will not activate unless this wire is grounded. When this wire is disconnected from ground, the remote start system is disabled. 1. The primary connection point for the Black/White wire is at the Neutral Safety Switch located on/at the transmission shifting lever. The switch output must be GROUNDED when the shifter lever is in the PARK position. 2. The second best connection point for the Black/White wire is at the Parking Brake Switch output wire. Make sure that when the parking brake is engaged that the output wire of the switch is grounded. 3. An optional remote start toggle switch can be added to temporarily disable the Remote Start Device. It can prevent the vehicle from being remote started accidentally. This feature is useful if the vehicle is being serviced or stored in an enclosed area. To disable the remote start, move the optional remote start enable toggle switch to the OFF position. To enable the remote start, move the optional remote start enable toggle switch to the ON position. Note: When the Black/White wire is not used for it’s intended safety purpose, connect the Black/White wire to the “Ground” or remote start system will not function. Wiring (continued) 11 Black/White Wire: (-) Neutral Safety Switch Input Black/White Wire Neutral Safety Switch Input P R N 2 1 Optional Enable Switch Ignition Electronic Control Module (ECM) Solid State, Do Not Measure Resistance White 9-Pin Mini Connector Violet/WhiteWire: (-) Tachometer Signal Connection

This wire provides instant shutdown for the remote start, when it receives +12 volts. If the brake lights switch in the vehicle switches +12 volts to the brake light circuit, connect this wire to the output side of the brake switch. This will allow the remote start to shut down if an attempt is made to operate the vehicle without the key while running under the control of the remote start. A relay may be required if the brake light switch is (-) type. White 9-Pin Mini Connector Brake Light Bulbs +12 Volts Switch Closes when Brake is Depressed Brown Wire Brake Pedal To Lights Gray Wire: (-) Hood Safety Shut Down Input The Gray wire provides instant shutdown for the remote start when it is grounded. Connect the Gray wire to an existing hood pin switch or install the one provided in this kit. This wire must be routed through a grommet in the firewall and connected to the hood pin switch. If the hood pin switch is also to be used as an alarm system trigger, diodes are required as shown. Important! This connection is a safety wire and must be connected as shown and tested as specified. Failure to do so may result in personal injury or property damage. Note: The Gray wire can also be used as the “Brake Safety” connection if the vehicle brake light circuit switches a ground signal to the brake lights. An isolation diode must be used and connected to the output of the brake switch. Hood Pin Switch Gray Wire Negative Safety Diode Diode To Alarm Instant Trigger Blue Wire White 9-Pin Mini Connector White/Blue Wire: AUX Start and Turn Off Input This wire can turn on and off the remote start system each time it sees a momentary ground signal. This wire is normally used for testing or activating the remote starter from an after-market alarm system. A common connection point would be at the trunk release wire or the door lock wire. HC4: White 9-Pin Accessory Harness (continued)

Dome Light Control Output : This wire becomes grounded when the system is unlocked. The current capacity of this wire is 200mA. This wire can control the operation of the interior lights. Use of optional relay as shown is recommended. Upon unlocking, the interior lights will remain on for 30 seconds. Ground Output During Crank Option: (See “Alarm Feature Programming”): This wire can be used to control another device as needed when the remote start is cranking the engine. This wire will supply a constant ground while the engine is cranking. Driver’s Door Priority 2nd Unlock Output: By default the Light Blue wire provides a second (-) unlock output to unlock the passenger’s doors. Follow the diagrams on pages 8-10 for proper connection. Factory Security Disarm Output: The Light Blue wire can be programmed to provide a (-) pulse output every time the X6 is unlocked. This connection can be used to disarm the vehicles factory security system at the same time the X6 is unlocked. See Alarm Feature Programming (Group 1), page 18. Start Status Output: The Light Blue wire can be programmed to provide a constant (-) output during the time that the vehicles engine is running under the control of the X6. In this configuration, the Light Blue wire can be used as sensor bypass control. Connect a relay to the sensor power wire and use the Light Blue wire to trigger the relay. See Alarm Feature Programming (Group 1), page 18. Some newer vehicles use a third ignition wire which is required to start and keep the vehicle’s engine running. The Pink wire provides a 200mA (-) ground output that becomes active 4 seconds before the remote start unit initializes. This wire remains grounded while the engine is running. This is a low current output wire and will require a 30a/40a relay (not supplied) for correct operation. Wire the relay as shown. Note: This wire can an also be used to control an ignition immobilizer bypass module. 87 87a 86 85 30 White Wire White 9-Pin Mini Connector +12V Courtesy Light Door Switch Fuse +12 Volts or Ground Depending on Vehicle Requirement White Wire : (-) 200mA Programmable Output (Dome Light Supervision Default Setting) Light Blue Wire : (-) 200mA Programmable Output (2nd Unlock Output Default Setting) Pink Wire : (-) 200mA Ignition 3 Output 87 87a 86 85 30 Pink Wire +12 V Constant Fused 25A Capable Ignition 3 Wire from Ignition Key Switch White 9-Pin Mini Connector

Pink Wire White 9-Pin Mini Connector HC4: White 9 Pin Accessory Harness (continued) Transponder Interfacing Using ALA984 Relay: Can also use optional RS-TIM bypass module. If the vehicle has transponder system installed, you will need to bypass the system while the vehicle is operating under the control of the Remote Start Unit. To do this, follow these steps: 1. You will need a transponder key that’s already programmed to the vehicle. 2. Remove the trim around the ignition switch. 3. Wrap a thin (30 awg) wire tightly around ignition switch 6 to 8 times and secure it. 4. About 6" down line make another loop of approximately 2" diameter. 5. Place the key inside this loop and secure it to the loop. 6. Connect on end of the 30 awg wire to pin (87) of the relay module. 7. Connect the other end of the loop wire to Pin (30) of relay module. 8. Connect (86) to ignition, connect (85) to the Yellow wire of 5-pin mini white connector. GM VATS Key Override Using ALA984: Can also use RS-PLM bypass module. Passkey/Vats: Anti-Theft Bypass 87 87A 85 86 30 To Ignition White 9-Pin Mini Connector Passkey Wire Computer Side Orange or Black Plastic Tube at Steering Column Resistor Cut Passkey Wire Key Side Pink Wire

The Red/White will become grounded for 1 second when activated by the remote transmitter. The current capacity of this wire is 200mA and may require an additional relay to operate properly. 87 86 85 30 (Relay Not Supplied) Output to Power Trunk Switch To Constant +12 Volts Input to Relay (+ or -) White 9-Pin Mini Connector Red/White Wire Wiring (continued) Resistor Yellow Trucks: Orange/Black or Cars: Black Passkey II Passive Anti-Theft Bypass 87 87A 85 86 30 To Vehicle's Ignition Wire Trucks: Red/White or Cars: White White 9-Pin Mini Connector Pink Wire HC4: White 9 Pin Accessory Harness (continued) P2 Valet Switch Plug-In Harnesses

Plug-In Harnesses (continued) Black Wire No Connection Red Wire No Connection DBI Conection Harness (supplied) P7 Data Adapter Communication Data Interface Harness: Allows direct communication between Marksman Remote Start and the vehicle’s data bus communication. (Data Interface Modules sold separately) Note: The DBI Connection Harness provides power and ground to the Data Interface Module. Do not connect power and ground from Data Interface Module Harness.

ignition switch On - Off - On - Off - On. Before 15 seconds has passed, push and release the valet switch 3 times holding the button down on the 3rd press. Wait until you hear a long chirp from the siren/horn. Release the button. You are now in “Programming the Transmitter” mode. Step 1 Step 2 The transmitters included with this system have been pre-programmed and should not need re-programming. Note: This system will accept codes from 4 transmitters. If more than 4 transmitters are programmed, the system will only operate from the last (4) programmed transmitters. Follow the enclosed procedure to program additional transmitters: 3X 2X + 1X (Hold) Step 3A Press the “Lock” button on the first transmitter until you hear a confirmation chirp/beep. The transmitter is now coded into the system. Step 3B Repeat Step 1 for each additional transmitter. Step 4: Exit Programming When finished, either turn off the ignition key or wait for 15 seconds to get out of transmitter programming mode. You will hear 3 long chirp/beeps to indicate you are out of the “Programming the Transmitter” mode. Programming the Transmitter

Two LED Pulses Three LED Pulses Four LED Pulses (Default Setting) With the ignition switch in the OFF position, turn the ignition switch On - Off - On - Off - On - Off. Before 15 seconds has passed, push and release the valet switch 2 times holding the button down on the 2nd press. Wait until you hear 1 short and 1 long chirp/beeps. Release the button. You are now in “Alarm Feature Programming (Group 1)” mode. Step 1 Step 2 3X 1X + 1X (Hold) Step 3 Remote Feature Programming Press the transmitter buttons as illustrated to adjust the features required. Keep re-pressing the transmitter button that relates to the feature you want to adjust until the correct amount of chirp/beeps is heard then move on to the next feature. All Chirps On All Chirps Off Parking Light On for 30 sec. after Unlock Signal Parking Light On 10 sec. after Lock and 30 sec. after Unlock Pathway Illumination Off HC4 Light Blue Wire: 2nd Unlock Output HC4 Light Blue Wire: Fact. Security disarm Output HC2 Brown Wire: (-) Horn Output HC4 White Wire: (-) Domelight Supervision Output HC4 White Wire: (-) Output During Starting Normal Horn Output Pulse Duration PVID 1 Horn Output S-S-S - L-L-L - S-S-S PVID 2 Horn Output S-L-S-L PVID 3 Horn Output S-S-S-L PVID 4 Horn Output S-M-L-S-M-L PVID 5 Horn Output S-S - L - S-S Five Chirps Five LED Pulses Six Chirps Six LED Pulses Keyless Entry Feature Programming (Group 1) HC4 Light Blue Wire: Start Status Output HC2 Brown Wire: Fact. Security Re-arm Output + +

3 long chirps and 3 flashes of the parking lights will confirm exit of the programming mode. Note: Waiting 15 seconds after the last command will also cause the system to automatically exit the programming mode. Step 4 Exit Programming With the ignition switch in the OFF position, turn the ignition switch On - Off - On - Off - On - Off. Before 15 seconds has passed, push and release the valet switch 4 times holding the button down on the 4th press. Wait until you hear 2 short chirps/beeps + 1 long chirp/ beep. You are now in “Alarm Feature Programming (Group 2)” mode. Step 1 Step 2 3X 3X + 1X (Hold) One Chirp Two Chirps Three Chirps Four Chirps Button One LED Pulse Two LED Pulses Three LED Pulses Four LED Pulses (Default Setting) Step 3 Double Unlock Pulse Ignition Controlled Door Lock Only Ignition Controlled Door Unlock Only Ignition Key Controlled Door Lock and Unlock Doors Lock Before Start All Door Lock / Unlock Control Off HC4 White/Blue Wire: One (-) input pulse to activate Remote Start HC4 White/Blue Wire: Three (-) input pulses to activate remote start 3.5 Second Door Lock Pulse 0.8 Second Door Lock Pulse Ignition Key Door Lock Control Off Door Lock with "Comfort Features" Doors Lock After Shutdown Doors Lock Before Start and Doors Lock After Shutdown Remote Feature Programming Press the transmitter buttons as illustrated to adjust the features required. Keep re-pressing the transmitter button that relates to the feature you want to adjust until the correct amount of chirp/beeps is heard then move on to the next feature. Comfort Feature: Some vehicles (Mercedes, BMW, VW,etc.) have a special “Comfort Feature”. When you lock the door with the ignition key, you keep the key in the “lock” position for about 5 or 7 seconds and the windows will close. If the vehicle has a “Comfort Feature” and you want the windows to closed upon Lock/Arm the security system, you can set the door lock output to “Comfort Feature”. Keyless Entry Feature Programming (Group 1) (continued) Keyless Entry Programming (Group 2)

Two LED Pulses Three LED Pulses Four LED Pulses (Default Setting) Before 15 seconds has passed, push and release the valet switch 8 times holding the button down on the 8th press. Wait until you hear 4 short chirps/beeps + 1 long chirp beep. Release the button. You are now in “Remote Start Feature Programming” mode. 3X 7X + 1X (Hold) Step 3 10 Minute Run Time Factory Alarm Disarm with Channel 3 “On” Diesel Engine and 10 Second Warm-up Gasoline Engine Diesel Engine and 15 Second Warm-up Diesel Engine and 20 Second Warm-up 20 Minute Run Time 30 Minute Run Time 5 Minute Run Time Without this Feature Constant Parking Light Output Flashing Parking Light Output Step 1 Step 2 Press the (*) Button = Activates Remote Start Press the (* - *) Button = Activates Remote Start 3 Hour Time Start 2 Hour Time Start With the ignition switch in the OFF position, turn the ignition switch On - Off - On - Off - On - Off. Remote Feature Programming Press the transmitter buttons as illustrated to adjust the features required. Keep re-pressing the transmitter button that relates to the feature you want to adjust until the correct amount of chirp/beeps is heard then move on to the next feature. Remote Start Feature Programming (Group 1) Five Chirps Diesel-DBI + +

Tw o C rih ps On e C rih p Button One LED Pulse Two LED Pulses Three LED Pulses (Default Setting) Turbo Timer Control is Active Press the ( + ) buttons before removing the ignition key to activate the 1 minute Turbo timer control. The keyless entry system can lock the doors while the engine is running 21 Turn On the Ignition 3 long chirps and 3 flashes of the parking lights will confirm exit of the programming mode. Note: Waiting 15 seconds after the last command will also cause the system to automatically exit the programming mode. Step 4: Exit Programming Remote Start Feature Programming (Group 1) (continued) (Default Setting) Turbo Timer Control Function is Off. The keyless entry system can not lock the doors while the engine is running. Turbo Timer Control is Active Press the ( + ) buttons before removing the ignition key to activate the 3 minute Turbo timer control. The keyless entry system can lock the doors while the engine is running Turbo Timer Control is Active Press the ( + ) buttons before removing the ignition key to activate the 5 minute Turbo timer control. The keyless entry system can lock the doors while the engine is running Four Chirps Four LED Flashes Notice: The Turbo Timer feature will not operate when using the 1 button transmitter Five Chirps Four LED Flashes The vehicle has an aftermarket turbo timer installed. The keyless entry system can lock the doors while the vehicle is running. +

LED Two Pulse LED Three Pulse LED Four Pulse (Factory Default Setting) Exit the Programming Mode (3 long chirps and 3 parking light flashes to confirm this exit) Tachometer Checking Type RPM Learning Start Timer: 0.6 second (1 chirp) 0.8 second (2 chirps) 1.0 second (3 chirps) 1.2 second (4 chirps) 1.4 second (5 chirps) 1.6 second (6 chirps) 1.8 second (7 chirps) 2.0 second (8 chirps) 3.0 second (9 chirps) 4.0 second (10 chirps) Voltage Checking Type Fixed Crank Mode + Low Check Level High Check Level 22 9X + 1X (Hold) Step 2 Step 1 3X Enter the crank detection programming mode, select the engine checking type, then follow the procedures to test and re-set the cranking parameters as needed. Note: The default detection setting is “Voltage Detection”. Once your wiring is completed, you can press the button (2) times and start the engine to make sure all your connections are good to this point. With the ignition switch in the OFF position, turn the ignition switch On - Off - On - Off - On - Off. Before 15 seconds has passed, push and release the valet switch 10 times holding the button down on the 10th press. Wait until you hear 5 short chirps/beeps + 1 long chirp/beep. Release the button. You are now in “Engine Crank Detection Programming” mode. Engine Crank Detection Programming Use the transmitter buttons as illustrated to adjust the features required. Keep re-pressing the transmitter button that relates to the feature you want to adjust until the correct amount of chirp/beeps is heard. Move on to the next feature. In this programming group you will set the type of engine starting detection you want to use in your installation. There are 3 types available: 1. Tachometer (RPM) Detection: (Most reliable and recommended) This type of detection requires a wire connection to the vehicles ignition coil. You must also “teach” the remote start unit the engine idle RPM level before you can start the engine by remote 2. Voltage Detection: This method detects the drop and rise in the battery voltage when the vehicle is started by remote. This type of detection requires a solid main power input connection but it does not require any additional hard wire connections. 3. Elapsed Timer: This method is the easiest for installation but is not always the best method for year round usage (Summer and Winter). To operate this method, you will program a specific time window for the remote start to crank the engine. Battery strength, environment and the aging process of the vehicle may require the timer to reset from time to time or season to season. Engine Crank Detection Programming Explanations

1 Voltage Type A. Press the button two times to start the engine. Allow engine to run for more than 10 seconds. A1. If the engine shuts off before 10 seconds, follow the “Engine Crank Detection Programming” Step 1 and Step 2 procedure on page 22 to change “low check level” to “hi check level” (2 chirps). Exit the programming mode and Repeat A above. A2. If the engine cranks too long or too little, follow the “Engine Crank Detection Programming” Step 1 and Step 2 procedure on page 22 to select a different crank duration (see chart enclosed). Exit the programming mode and Repeat A/A1 above. Press Buttons Chirp/ LED Flash Checking Type Test and Adjustment Procedure 2 Tachometer Type Step 3B Crank Detection Programming and Procedure Step 3A Crank Detection Programming and Procedure Press Buttons Chirp/ LED Flash Checking Type Test and Adjustment Procedure 3 Fixed Crank Mode A. Press two times to start the engine. Allow engine to run for more than 10 seconds. A1. If the engine cranks too long or too little, follow the “Engine Crank Detection Programming” Step 1 and Step 2 procedure on page 22 to select a different crank duration (see chart enclosed). Repeat A above. Engine Crank Detection Programming (continued) Step 3C Crank Detection Programming and Procedure A. Learn the engine idle RPM. 1. Press and release the button on the transmitter. 2. Start the engine with the ignition key and allow the choke to turn off. 3. With the engine at true idle speed, press and hold the valet switch until you hear (1) long chirp and the LED is on solid for two seconds. Note: If you do not get a response from holding down the valet switch, check your tach connection. It may be loose or incorrect. 4. Turn off the ignition key. B. Press the button two times to start the engine. Allow engine to run for more than 10 seconds. B1. If the engine shuts off before 10 seconds, follow the “Engine Crank Detection Programming” Step 1 and Step 2 procedure on page 22 to change “high check level” to “low check level” (2 chirps). Repeat B above. B2. If the engine cranks too long or too little, follow the “Engine Crank Detection Programming” Step 1 and Step 2 procedure on page 22 to select a different crank duration (see chart enclosed). Repeat B/B1 above. + + +

OFF position to the ON position 3 times leaving it in the Off position the third time. 3X Step 1 Before 15 seconds has passed, push and release the valet switch 12 times holding the button down on the 12th press. Wait until you hear 6 short beeps. Release the button. 11X + 1X (Hold) Step 2 Press the (Lock) and (Car) button on the transmitter together for 6 seconds, there will be a confirmation six chirp with 3 long chirp and 3 parking light flashes to confirm the system “Alarm Features 1, 2 and 3 Programming” all returns to factory default setting. Step 3 Turn On the Ignition 3 long chirps and 3 flashes of the parking lights will confirm exit of the programming mode. Note: Waiting 15 seconds after the last command will also cause the system to automatically exit the programming mode. Step 4: Exit Programming The unit has the ability to report the cause of the last shutdown of the remote start system. Enter the Vehicle: 1. Turn the Ignition switch to “On” position. 2. Press the button on the transmitter 3. The LED will now report the last system shutdown by flashing for 3 cycles in the following grouped patterns: LED Shutdown Mode Flashes 1 (-) Safety Shutdown Input (Hood) 1. Close the Hood (+)Safety Shutdown Input (Brake) 2. Check White/Black Wire Connection (7-Pin Mini Black) or Neutral Safety Switch Input 3. Check White/Violet Wire Connection (7-Pin Mini Black) n oitis On p ” o “ ot h w cti S elg og T elb E e na ht e .4 Mov F lia (If Installed) 5. Move the gear selector to “Park”/”Neutral” Position. 6. Check Black/White Wire Connection (7-Pin Mini Black) 3 No RPM or Low Voltage: Tachometer Checking Type: Check White/Red wire Connection Voltage Checking Type: Program the “Check Level” from “Hi Check Level” to “Low Check Level” 5 Over-Rev 6 System Timed Out 7 Transmitter is Off 8 Tach. Signal has not been learned Re-learning the RPM Remote Start Shutdown Diagnostics Returning to Factory Default Settings (Reset Keyless Features Only)

OFF position to the ON position 3 times leaving it in the Off position the third time. 3X Step 1 Before 15 seconds has passed, push and release the valet switch 12 times holding the button down on the 12th press. Wait until you hear 6 short beeps. Release the button. 11X + 1X (Hold) Step 2 Press and release the (Car) button first. Step 3 Turn On the Ignition 3 long chirps and 3 flashes of the parking lights will confirm exit of the programming mode. Note: Waiting 15 seconds after the last command will also cause the system to automatically exit the programming mode. Step 5: Exit Programming Return to Factory Default Settings (Resets All Programmable Features) Press and hold the (Lock) and (Car) button on the transmitter together for 6 seconds, there will be a six chirp confirmation with 3 long chirp and 3 parking light flashes to confirm the system “All Features return to factory default setting. Step 4

responsibility of the installing technician to complete these tests. Failure to test the unit in the following manner may result in personal injury, property damage, or both. 1. Test the brake shutdown circuit: With the vehicle in “Park” (P), start the vehicle using the remote transmitter, Once the engine is running, press the brake pedal. The vehicle should shut down immediately. If the vehicle continues to run, check the brake circuit White/Violet wire. 2. Test the “Hood Pin” shutdown circuit: Start the vehicle using the remote transmitter, Once the engine is running, pull the hood release and raise the hood. The vehicle should shut down immediately. If the vehicle continues to run, check the hood pin “White/Black” wire connection. 3. Neutral Start Safety Test: A. Set the vehicle parking brake. B. Block the drive wheels to prevent vehicle movement. C. Sitting in the vehicle, turn the ignition switch “On” or “Run” position. But do not start the engine. D. Step on the brake pedal and shift the gear selector into “Drive” (D). E. Put you foot over the brake pedal but do not press down on it. Be ready to step on the brake to shut down the Remote Start Device. F. Start the vehicle using remote transmitter. a. If the starter does not engage, the test is complete. b. If the starter engages, immediately step on the brake pedal to shut down the system, recheck your Violet wire (6-Pin White, Starter Output) connection. The heavy gauge Violet wire must be connected to the ignition switch side of the Neutral Start Switch. If the vehicle you are working on does not have an Electrical Neutral Safety Switch, it will be necessary to reconfigure the Remote Starts Wiring to accommodate this vehicle. The information concerning the Mechanical Neutral Safety Switch provided below will help you to determine if the vehicle you are working on has this type of safety switch and will provide alternate wiring methods to accommodate this situation. Safety Testing the Installation

© Copyright 2008/ 2009 Magnadyne Corporation (-) (-) (-) (-) Valet Switch Transceiver LED Indicator HC1 White 6-Pin HC2 White 5-Pin HC3 Black 3-Pin HC4 White 9-Pin P2 Blue 2-Pin P6 White 3-Pin P7 Brown 4-Pin Data Port Wiring Diagram