Inter-m TP-6231 Operation Manual

and the Caribbean) do not have handles installed due to customer preference.

All of the co-workers here at Inter-M are dedicated to providing excellent products with inherently good value, and we are delighted you have purchased one of our products. We sincerely trust this product will provide years of satisfactory service, but if anything is not to your complete satisfaction, we will endeavor to make things right. Welcome to Inter-M, and thank you for becoming part of our worldwide extended family! RISK OF ELECTRIC SHOCK DO NOT OPEN Caution CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WaRninG To prevent fire or shock hazard, do not expose the unit to rain or moisture. *WARNING FOR YOUR PROTECTION PLEASE READ THE FOLLOWING-WATER AND MOISTURE: Unit should not be used near water(e.g. near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc). Care should be taken so than objects do not fall and liquids are not spilled into the enclosure through openings. *Do not install this equipment in a confined space such as a book case or similar unit. *This apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such vases, shall be placed on the apparatus. *This apparatus shall be connected to a mains socket outlet with a protective earthing connection. *It has heed to be easy to disconnect the device. To disconnect the device from power, separate AC input cable from inlet or unplug the AC Cord. Caution *These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. notE *This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operation and maintenance (servicing) instructions in the literature accompanying the appliance. Caution: To prevent electric shock do not use this (polarized) plug with an extension cord, receptacle or other outlet unless the blades can be fully inserted to prevent blade exposure. Attentions: Pour prévenir les chocs électriques ne pas utiliser cette fiche polarisée avec un prolongateur, une prise de courant on une autre sortie de courant, sauf si les lames peuvent étre insérées à fond sans en laisser aucune partie à découvert.

Features............................................................................................................................................3 Equipment Set-up and Check List ................................................................................................4 Front Panel ......................................................................................................................................7 Rear Panel .......................................................................................................................................8 Operation Flow Chart..................................................................................................................12 Applications ..................................................................................................................................13 Block Diagram ..............................................................................................................................14 Specifications ................................................................................................................................15 Service Procedures....................................................................................................................................17 Schematic.....................................................................................................................................17 Parts List .......................................................................................................................................17 Variations and Options ...............................................................................................................17 Warranty .......................................................................................................................................17

read this brief manual and familiarize yourself with the important information regarding product features, setup and operation. As with most electronic devices, we strongly recommend you retain the original packaging. In the unlikely event the product must be returned for servicing, the original packaging (or reasonable equivalent) is required. Installation Environment Never place this product in an environment which could alter its performance or reduce its service life. Such environments usually include high levels of heat, dust, moisture, and vibration. IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. S3125A

When connected to a regular telephone line (trunk) or via telephone switching station and a regular telephone this device can perform paging or broadcasting by using normal telephone, cell phone and public telephone. - SELECT 2 OR 4 WIRE CONNECTION TYPE 2 wire: same method as general telephone 4 wire: Exchange interface type (2W E&M) - OFF HOOK SIGNAL DETECT (CALL END) - AUTO RESPONSE SERVICE (ARS) ARS function is available with voice prompts and broadcasting services for user convenience. Message can directly be recorded by the user. - SET PASSWORD User password can be set. - BROADCAST MODE SELECTION Depending on user requirement, broadcasting mode can be selected. - VOICE RECORD FUNCTION Broadcasting messages can be recorded by the user. Up to 20 seconds can be recorded.

Equipment Set-up and Check List 1. Make sure system is turned off before configuring the set-up. 2. PD-6359 REMOTE CONTROL If remote control of PD-6359 is required, connect the power remote terminal of the TP-6231 (Terminal 5 on rear diagram of TP-6231) to the remote terminal of PD-6359. 3. Telephone line connection (2 configurations). - 2 WIRE TELEPHONE INTERFACE Connect a standard telephone (RJ11) line wire to the TP-6231(Terminal 13 on rear diagram of TP-6231) - 4 WIRE (2W E&M) Refer to figure below for connector pin assignment. Used if you want to install a 2W E&M where private exchange is installed. 4. Broadcast Management Dial CODE Telephone broadcasting Dial Codes. (Based on dial buttons) ※Note: When the paging broadcasting must be finish an asterisk (*), please exit by pressing the button. An asterisk (*) If you do not press the broadcast button and you can not finish properly. In this case, the power switch OFF then ON if it is restored. ① ⑥ ⑤ ② ③④ TELEPHONE INTERFACE ①MOUTH ②GND ③RING ④TIP ⑤EAR ⑥-48V TYPE Broadcasting Group Zone Broadcasting Normal Broadcasting Additional Functions CODE ✽7 7 # ✽7 0 # ✽7 1 # ✽? ? # ✽# ✽# ✽8 8 # ✽9 9 # REMARK ALL Broadcasting ✽70# : 01~08 Local ALL Broadcasting ✽71# : 09~16 Local ALL Broadcasting ✽??# : Select one from C01 to 16 ✽# # : Recording function ✽88# : Switch to user mode ✽99# : Release user mode

Serial Communication type: 1stop bit, non-parity, 8bits data, 9600 bps. CONTROL COMMANDS (If serial communication terminal is used) TP-6231 enables each commends. 6. Address Setting 1) ECS-6216P / RME-6108 If connected with ECS-6216P or RME-6108, set address number for proper connection conditions. 2) When connecting to ECS-6216P directly (Can also be used with RM-6024) - If Connected to RM1 terminal of ECS-6216P set address number of TP- 6231 to 1. - If Connected to RM2 terminal of ECS-6216P set address number of TP- 6231 to 9. CHANNEL 1. START CODE 2. SET 3. Command types 4. Operation commands 5. CHANNEL Number 6. SPACE CHANNEL 1 54Hex 60Hex + SET Number (Top 4BITS: MSB) 70Hex + SET Number (Sub 4BITS: LSB) 50Hex + Type of Number 23Hex : ON, 26Hex : OFF 30 - 3FHex FFHex REMARK SET number equal to the area code (01 - FFH) 50Hex=ALL, 51Hex=GROUP, 52H=EACH 23Hex : When you choosing broadcast local 26Hex : HOOK-OFF Select CHANNEL 1-16 END CODE RM1 INPUT AUDIO OUT AUDIO OUT RM2 INPUT ECS-6216P RM1 RM2 TP-6231 or RM-6024 TP-6231 or RM-6024 Address No: select 9 Address No: select 1

- If TP-6231 is connected to RME-6108 connected with RM1 terminal, address number should be selected among 1~8. - If TP-6231 is connected to RME-6108 connected with RM2 terminal, address number should be selected among 9~16. 4) How to set up equipment address number for TP-6231. Setting should be as table below: *Data value when Dip Switch is in ON position (Ex: when Dip Switch number 1 and 3 are ON, Data value 1 and 4 is added, so equipment address number will be 5.) 7. Setup the SECURUTY NUMBER, DELAY TIME switch of rear panel. If setup is wrong, BROADCASTING LED on the front panel will be ON. 8. Adjust the line output level by using volume on the rear panel. RM1 INPUT AUDIO OUT AUDIO OUT RM2 INPUT ECS-6216P RME-6108 RME-6108 RM1 RM2 TP-6231 or RM-6024 TP-6231 or RM-6024 Address No: select 9~16 Address No: select 1~8 RM 1 RM 2 RM 3 RM 4 RM 5 RM 6 RM 7 RM 8 INPUT OUTPUT ϊۑ@Ţ۩م@ێԟێ@ۘڽ@Ĉڐ@Ê۾@̝ɜট۩ۉ@کॼێ@ۘںɩ@ ࠭ҿșڽ@ّçǦ@ǷҜθ@ϊݖݖ@ψֲ֫٤N ܆ॄϿࠤ@Z@REMOTE MIC EXTENDER ЂʠϿ@Z RME 6108 ܄ÿۖͶ@Z DC 24V, 150mA ܆ܖۜϿ@Z ďÖݖڜࣶTEL : 1588 7074 DC 24V RM 1 RM 2 RM 3 RM 4 RM 5 RM 6 RM 7 RM 8 INPUT OUTPUT ϊۑ@Ţ۩م@ێԟێ@ۘڽ@Ĉڐ@Ê۾@̝ɜট۩ۉ@کॼێ@ۘںɩ@ ࠭ҿșڽ@ّçǦ@ǷҜθ@ϊݖݖ@ψֲ֫٤N ܆ॄϿࠤ@Z@REMOTE MIC EXTENDER ЂʠϿ@Z RME 6108 ܄ÿۖͶ@Z DC 24V, 150mA ܆ܖۜϿ@Z ďÖݖڜࣶTEL : 1588 7074 DC 24V Pin No. 1 2 3 4 5 Data 1 2 4 8 16 1 ON 2 ON 3 ON ON 4 ON Address 5 ON ON 15 ON ON ON ON 16 ON

LED illuminates when the phone is connected. 2. OPERATING LED This LED displays the operating status of equipment. When the state is normal, the LED flashes, and when Off indicates fault. 3. BROADCASTING LED LED will be ON if broadcasting is connected or being broadcasted. 4. AC OUTLET SWITCH Turns rear AC OUTLET on or off manually. 5. AC OUTLET LED It will be on when AC OUTLET switch is pushed ON. 6. POWER LED Indicated power on/off status. 7. POWER SWITCH Turns TP-6231 ON/OFF. 6 1 2 7 3 5 4

AC power output terminal, max 3A can be connected. Outlet is on if broadcasting or if manually activated by front AC OUTLET. 2. AC INLET AC power input connecting terminal. 3. ADDRESS Switch Sets the equipment address number. Should be set only when it is connected to ECS-6216P or RME-6108. Refer to page 5 of Equipment Setting for more detailed information 4. DATA & AUDIO Terminal (RJ-45) Connects to ECS-6216P or RME-6108 and supplies data and audio signal. 1 2 5 6 7 8 9 10 11 12 13 14 15 3 4 PIN NO. Functions 1 RS-422 Data - TX+ 2 RS-422 Data - TX- 3 RS-422 Data - RX- 4 Live Data 5 GND 6 RS-422 Data - RX+ 7 Balanced Audio Output - HOT 8 Balanced Audio Output - COLD

Connects to PD-6359 and once connected, the output contacts will be broadcast. 6. CONTROL OUTPUT TERMINAL 17 OPEN COLLECTOR output triggers with common ground which can be used to connect to remote 1 or 2 of ECS-616. 7. SECURITY NUMBER SETTING SWITCH - A TYPE : The tens input value - B TYPE : The first number input value 8. DELAY TIME SETTING SWITCH - TEL OFF Signal Time Adjustment (1~4) This switch sets the telephone off time. Set as table below, will HANG-UP or put the phone On-hook if thetelephone is left Off-hook. 1 2 3 4 5 6 7 8 TEL OFF Signal timing adjustment Determine the number Device operation of RING method installation 1 2 3 4 MODE OFF OFF OFF OFF 0 ON OFF OFF OFF 1 OFF ON OFF OFF 2 OFF OFF ON OFF 3 OFF OFF OFF ON 4 MODE SETTING CONNECT LINE 0 500±10 m/s Extension 250±60 m/s Outside wire 1 500±20 m/s Extension 250±60 m/s Outside wire 2 500±40 m/s Extension 250±60 m/s Outside wire 3 500±60 m/s Extension 250±60 m/s Outside wire 4 500±80 m/s Extension 250±60 m/s Outside wire 1 2 3 4 5 6 7 8 9 10 S/W SETTING 1 2 3 4 5 6 7 8 9 0 Input Value 1 2 3 4 5 6 7 8 9 10 S/W SETTING 1 2 3 4 5 6 7 8 9 0 Input Value

Determines the number of RINGs before the TP-6231 will answer when receiving a call. - Operational Method Setup Select from 2 possible operation modes as per table below: ※DIP switches during operation, must not operated, press the RESET switch. 9. UNIT ADDRESS SETUP SWITCH It is the switch which allocates the equipment number. (Input in hex. Value) MSB LSB This switch is used when sending the equipment address number or status information via the RS232 communication port terminal (Connector 15 on rear panel). ※[Reference] SERIAL OUT terminal. If used, remove the top cover and set the slide switch on the PCB board (S7) to the RS-232 position. 10. LINE OUT GAIN VOLUME Adjusts volume output level. 11. LINE OUTPUT TERMINAL 600ΩBALANCED OUTPUT. 12. 4 & 2 WIRE SELECTOR SWITCH SELECTOR SLIDE switch selects between 4 & 2 WIRE operation mode. 13. TELEPHONE INTERFACE RJ12 Connector. This terminal connects to the Telephone Line. Used for both 4 wire and 2 wire mode. Pin 1 Mouth, Pin 2 Ground, Pin 3 Ring, Pin 4 Tip, Pin 5 Ear, Pin 6 -48V 14. RESET SWITCH Status will be restored if normal operation. 5 6 RING 횟수 OFF OFF 0 OFF ON 1 ON OFF 2 ON ON 3 7 8 운용 방법 OFF OFF ALL 기능 ON OFF SECURITY 입력 생략 6* 7* DIP 스위치 1 2 3 4 5 6 7 8 실제 값 8 4 2 1 8 4 2 1 예 OFF OFF ON ON OFF ON OFF ON 결과 63 75

RS-232C SERIAL communication terminal (RX/TX). Figure below shows pin configuration and proper wiring. TP-6231(Female) Controller Pin No. 1 2 3 4 5 6 7 8 9 TP-6231 Definition NC RxD TxD NC GND NC NC NC NC # 2 RxD # 3 TxD # 5 GND # 2 RxD # 3 TxD # 5 GND D-SUB 9Cable(Twisted RS-232C Cable) Controller 6 7 8 9 1 2 3 4 5 6 7 8 9 1 2 3 4 5

Operation Flow Chart Telephone bell number of times O.K.=? CH1. Thank you. Connected to Tele-Paging Broadcasting. Operator Mode CH2. Insert Password Password Input O.K.=? Code Input O.K.=? Recorded voice announce in case of operator mode CH3. Wrong P/W and input again P/W input error 4 times O.K.=? CH12. Sorry and please try again Telephone Off Telephone Off CH4. Press * star and push zone selection 01~16 and press #. For all zone broadcasting, press 77. CH10. Wrong zone No. press again Broadcasting Mode CH9. Operator mode On CH11. Operator mode Off Busy Checking CH5. Broadcasting connected and make announce after the chime. Press * after finishing broadcasting CH7. To recorded message press 1. To stop press 2. To listen to the message press 3. To finish press “star”. CH8. Recorded and press 0 for confirmation, confirmation action. CH6. Chime sound Broadcasting Telephone Hook Off signal confirmation OK - CH16. End Message ※Note: When the paging broadcasting must be finish an asterisk (*), please exit by pressing the button. An asterisk (*) If you do not press the broadcast button and you can not finish properly. In this case, the power switch OFF then ON if it is restored.

BROADCASTING 5 9 4 8 3 7 2 6 1 P1 RDED 9P CONNECTION CPU I/O PART 2 & 4 WIRE METHOD SELECTOR 12V AC OUTLET AC IN2 AC IN1 SERIAL DATA COMMUNICATION SUB PROCESSOR CPU RS-232C BUFFER RX TX TX RX RJ-485 Transceivers RJ-45 JACK

place. ※Specifications and design are subject to change without notice. TP-6231 Frequency Response (0dB , +1/-3dB Decrease) 80Hz - 8kHz THD (0dB, 1kHz) Less than 1% Signal to Noise ratio (S/N) Better than 65dB AC OUTLET Switched : AC 230V/50Hz, 3A Remote Power control Circuit number 1 Circuit Speaker control circuit number 16 Circuit Output control All, Zone(2group), Individual Indicate Lamp STATUS LED of Four LINE OUT BALANCED 600Ω, -∞dB~12dB Communication Protocol RS-422(Maximum 1km/3,280 feet) Operation Temperature -10°C ~ +40°C Power Source AC 230V, 50Hz Power Consumption 700W (AC OUTLET + Equipment power consumption) Weight (SET) 4.2kg/9.3lb Dimensions (SET) 482(W)x88(H)x280(D)mm/19(W)x3.5(H)x11(D)in

provided in the troubleshooting portion of this manual may help with this process. Once it is certain that the problem is related to the product contact your warranty provider as described in the warranty section of this manual. Schematic A Schematic is available by contacting your warranty provider. Parts List A Parts List is available by contacting your warranty provider. Variations and Options Variations and Options Variations Products supplied through legitimate sources are compatible with local AC power requirements. Options No optional items are available for this product. Warranty Warranty Warranty terms and conditions vary by country and may not be the same for all products. Terms and conditions of warranty for a given product may be determined first by locating the appropriate country which the product was purchased in, then by locating the product type. To obtain specific warranty information and available service locations contact Inter-M directly or the authorized Inter-M Distributor for your specific country or region.

July 2014 131254 Inter-M, Ltd. (Korea) began operations in 1983. Since then, Inter-M has grown to become one of the largest manufacturers of professional audio and commercial sound electronics equipment in the world. Inter-M has gained worldwide recognition for its own branded products, as well as private label manufacturing of electronics sold under other names (OEM). The company is no longer just a Korean company, but rather a global company that is truly international in scope, with factories and offices in Korea and China, and sales and marketing operations located in Japan, Europe, and the U.S.A. With more than 850 employees around the globe, Inter-M is well-poised for further growth and expansion. Inter-M Americas, INC. 13875 ARTESIA BLVD. CERRITOS, CA 90703 USA TEL : +1-562-921-0313, FAX : +1-562-921-0370 Home Page : http://www.inter-m.net, E-mail : [email protected] Inter-M Corporation SEOUL OFFICE:653-5 BANGHAK-DONG, DOBONG-KU, SEOUL, KOREA TEL : +82-2-2289-8140~8, FAX : +82-2-2289-8149 Home Page : http://www.inter-m.com, E-mail : [email protected]