Inter-m VCD-412VIM Operating Manual

Operating Manual * Before starting use of this product, be sure to check the broadcasting mechanism and the power voltage.

Although it is neither complicated to install nor difficult to operate your set, a few minutes of your time is required to read this manual for a properly wired installation and becoming familiar with its many features and how to use them. Please take a great care in unpacking your set and do not discard the carton and other packing materials. They may be needed when moving your set and are required if it ever becomes necessary to return your set for service. Never place the unit near radiators, in front of heating vents, in excessively humid or dusty location to avoid early damage and for your years of quality use. Connect your complementary components as illustrated in the following page. Accessory

Contents Definition............................................................................1 Features..............................................................................1 Precautions........................................................................2 Components and Operation.............................................4 Function Setting................................................................7 How to Install.....................................................................9 Using to Ring Core..........................................................10 How to Connect Monitor and Peripheral Devices........11 Specifications..................................................................12 Trouble Shooting ............................................................13 Definition This camera is designed for easy installation in a luxury apartment or hotel. Its has a high resolution of 410,000 pixels with SONY CCD.

Features ■ ■Refined interior dome design ■ ■Adopted 1/3” 410,000 pixel Sony SUPPER HAD CCD, providing a clear picture quality with the horizontal resolution of over 480 TV image ■ ■Realized a high illumination with the minimum intensity of illumination of 1 Lux ■ ■Equipped with functions of automatic white balancing (AWB) and high speed automatic electric level control (ELC) ■ ■Equipped with backlight compensation function(BLC) ■ ■Possible to compensate for image blinking with flickering function in areas of frequency-interference ■ ■Simple to install and adjust the angles of camera ■ ■Audio Function Supported

RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operation and maintenance (servicing) instructions in the literature accompanying the appliance. Caution: These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do not any perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Attentions: Pour prévenir les chocs électriques ne pas utiliser cette fiche polarisée avec un prolongateur, une prise de courant on une autre sortie de courant, sauf si les lames peuvent étre insérées à fond sans en laisser aucune partie à découvert. Precautions

Warning DO NOT ATTEMPT TO INSTALL THE PRODUCT YOURSELF. WHEN SMOKE OR ABNORMAL HEAT EMISSION IS DETECTED, STOP USING THE CAMERA. It can result in fire. In this case, stop using the camera and refer servicing to a local agency or the Customer Service Department in the headquarters. This product must be installed by qualified personnel. Trying to install the product yourself can cause a risk of fire or electric shock. Thus, the user should consult with a nearby agency for proper permitting. DO NOT INSTALL THE PRODUCT IN DUSTY OR DAMP PLACES WITH POOR VENTILATION OR PLACES WITH OIL OR GAS. DO NOT PLACE THE PRODUCT IN UNSTABLE PLACES WITH VIBRATION OR ON A SLANTED SURFACE OR IN PLACES WITHOUT SECURE MOUNTINGS. The product must be securely fastened to avoid mounting failure that can inflict damage to the product and even jeopardize a person’s life. It will cause the abnormal operation of the product or result in a risk of electric shock or fire. DO NOT GRASP OR PULL THE POWER CORD OR PLUG WITH WET HANDS. DO NOT DISSEMBLE THE PRODUCT OR INSERT UNDESIRED FOREIGN SUBSTANCES. When the cord or plug is damaged or frayed, it can cause fire or electric shock. It will result in the abnormal operation of the product and fire. This sign is provided to alert the user to the presence of possible hazards that could cause serious injury or even death. Warning This sign is intended to alert the user to the presence of possible hazards that could cause personal injury or property damage. Caution

Precautions DO NOT INSTALL THE CAMERA IN EXTREME TEMPERATURE CONDITION DO NOT INSTALL THE CAMERA UNDER UNSTABLE LIGHTING CONDITION Unstable lighting can cause the camera to work improperly. If the camera is exposed to spotlight or object reflecting strong light, smear or blooming may occur. Do not use the camera under condition where temperature is over -10°C to 50°C. Especially be careful for ventilation under high temperature. DO NOT DROP OR SHAKE THE CAMERA DO NOT INSTALL THE CAMERA FACE UNDER STRONG LIGHTING CONDITION It can cause malfunction of CCD. It can cause malfunction. DO NOT TOUCH THE LENS DO NOT INSTALL THE CAMERA UNDER WET OR RAIN It can cause the image quality to be poor. If it gets wet, it can cause the camera out of order. DO NOT INSTALL THE CAMERA CLOSELY AT THE MAGNETIC DO USE A DRY CLOTH TO CLEAN THE CAMERA It can cause malfunction. To sweep the camera, use a dry and soft cloth. This sign indicates practices considered ‘unacceptable’ during use of the product. This sign illustrates mandated practices during use of the product. * Please check that the power satisfies the normal specification before connecting the camera.

111. WINDOW DISPLAY Transparent plastic cover to protect the camera lens. Be careful not to give any scratch to it. 22. DC JACK Usable to connect to a power source. This device is com- partible with static voltage DC12V 400mA. Be sure to use the appropriate adaptor. 33. DIP SWITCH To set various functions ON/OFF. 44. DC AUTO IRIS LENS Built-in DC AUTO IRIS LENS. This device is designed with built-in DC AUTO IRIS (VARIFOCAL 4~9mm). Lens so that users can easily adjust the image level and angle. Be careful to keep the surface of the lens from dust or foreign materials. 55. PCB BOARD Camera’s functions are performed here. Be careful when handling this board. 66. TOP BASE Cover to protect the camera. Possible to turn the camera lens right or left when installed 77. MIC Audio microphone, Possible to check the site situation by audio . It is available to communicate from center. 88. BOTTOM BASE The body of camera can be used to attach the camera to a wall.

999. BNC JACK VIDEO output jack. Possible to connect the video image to a monitor or other peripheral equipment through this jack. 1100. RCA JACK Audio voice output port, through which you can connect voice to a monitor or other peripherals. 1111. BRIGHTNESS-ADJUSTING VOLUME You can adjust the brightness of image the iris of DC AUTO IRIS LENS at VCD-412VIM. 1122. MIC BOARD A microphone board which enables you to hear voice. By attaching a mike to this device, you can identify what's going on at the site; and adjust a switch between MIN and MAX as you want. 1133. AUDIO OUTPUT LEVEL SWITCH By adjusting this switch between MIN and MAX, you can control the audio output level. If you put the switch to MAX position, the output level is 0 ±3dB.

ON 1 2 3 4 1 2 3 4 Function Setting Use the four switches to set each function. 11. FLK (FLICKERLESS) ON/OFF Set the FLK switch ON to prevent any flicker. ON : The shutter speed is set at 1/100, it is possible to see good image in a FLICKER area. OFF: Set the switch OFF in other areas than FLICKER. 22. AGC(AUTO GAIN CONTROL) ON/OFF If you need the automatic gain control, set the AGC switch ON/OFF as necessary. ON : When the input image is dark, this function will make it bright. At this time, the image becomes bright, and the noise also increases. OFF: The gain function does not function when it is dark.

333. ELC(ELECTRIC LEVEL CONTROL) ON/OFF Automatically adjusts the speed of the electronic shutter according to the amount of light coming into the camera. ON : Automatically adjusts the speed of the shutter according to the amount of light coming into the camera within the scope of 1/60 ~ 100,000 seconds. OFF: At this time, the electronic shutter does not work, so adjust the iris of the lens for a desired image level according to circums tances. How to adjust the iris of lens: Please refer to No.4-3 for the brightness- adjusting volume. If you turn the volume left, the iris will be closed, and if you turn the volume left, the iris will be closed, and if you turn it right, it will be opened. 44. BLC (BACK LIGHT COMPENSATION) ON/OFF You can see the object clearly with this function when it is in a strong backlight. ON : Possible to see the object clearly in a strong back-light. OFF: The backlight compensation function does not work. When a bright spot and a dark spot come in the monitor at the same time(EX. such as the windowside where strong sunlight comes in), the back-ground (bright part) becomes white.

78mm How to Install 11. Open the Top Base, and fix the camera at the place to install by using the screw. * To separate the Top Base, turn it while pulling it slightly. When it sounds “click”, pull the over off. 22. Adjust the camera position to the target area right, left, up or down, and put the cover on the camera.

Using to Ring Core 11. Open the cover of RING CORE, then put the cable in the center of RING CORE. 22. Close the cover of RING CORE after pass the cable two times over RING CORE.

■ ■Refer to the product manual because the method of connection varies depending on the devices. ■ ■Before connecting, make sure that all power switches of all the devices are turned off. ■ ■When connecting, set the 75Ω switch on the middle controller of each device to OFF or HI and the final monitor to 75Ω. ■ ■Use coaxial cable with 75Ω impedance when connecting. 13 VCD-412VIM(COLOR DOME CAMERA) BNC Cable Middle Controller Final Monitor RCA Cable Audio Audio Video Out Jack Audio Voice Out Jack Power

Specifications ■ ■ELECTRICAL ■ ■GENERAL Image Sensor 1/3IT SUPER HAD SONY CCD(410,000 pixels) Effective Pixels NTSC 768(H) x 494(V) PAL 752(H) x 582(V) Scanning System 2:1 INTERLACE Synchronizing System INTERNAL Scanning Frequency NTSC H 15.734kHz V 59.94Hz PAL H 15.625kHz V 50Hz Min. Illumination 1 Lux(F1.2) Video Output 1.0Vp-p COMPOSITE OUTPUT, 75Ω Horizontal Resolution more than 480 TV LINES S/N Ratio 50dB(AGC OFF) Shutter Speed NTSC 1/60~1/100,000sec PAL 1/50~1/100,000sec Operating Temperature -10°C ~ +50°C Applied Lens DC AUTO IRIS LENS 4~9mm White Balance ELECTRONIC AUTO TRACKING AUDIO(SWICH MAX) Input Sensitivity -60dB S/N Ratio more than 40dB Audio Output 0±3dB THD Less than 3% Power Source DC 12, 400mA Power Consumption 2.5W Weight 230g Dimensions 115(ø) x 90(H) mm

REFER TO THE FOLLOWING. * White blemish Cosmic rays or alpha rays affected to the CCD pixel and make white dot from the CCD surface in the condition of dark. Problem Solution THE IMAGE ON THE SCREEN IS DARK ★Check the line of power source. THE IMAGE ON THE SCREEN IS DARK ★Check the cable of video signal THE IMAGE ON THE SCREEN IS DIM ★Check if the lens is stained. THE IMAGE ON THE SCREEN IS DIM ★Adjust the focus of the lens again. ★Check the condition of Monitor. THE CAMERA IS NOT WORK PROPERLY. AND ★Check that you have connected the THE SURFACE OF THE CAMERA CASE IS HOT ★camera to a proper power source ★(DC 12V 400mA). SCREEN IS DARK. ★Adjust the monitor status. ★Check if the inter-system connection is normal. CAMERA OPERATION STATUS IS ABNORMAL. ★Check if the voltage input to a camera is ITS SURFACE IS TOO HOT, AND BLACK out of the specifications, or varies from LINES ARE DISPLAYED ON A SCREEN. time to time. 15 VCD-412VIM(COLOR DOME CAMERA) It may show white blemish in the condition of darkness. This dot appeared in use by external factors.