HP 12C Operating Instructions

Operating Modes and Clearing Procedures Number representation Settings and annunciators Memory organization How to selectively clear memory contents

Number representation There are many different settings that allow the user to customize the HP12C Platinum according to personal needs. One of the basic settings is related to number representation. Basic financial operations usually show two decimals of currency, requiring two digits after the radix mark (decimal point), and this is the default representation. The HP12C Platinum allows the number of decimal digits of the number in the display to be changed with the following keystroke sequence: f[number key] where [number key] refers to any key from 0 to 9. Example 1: Calculate 4/7 and show the resulting value with four, six and seven digits after the radix mark. Solution: The following keystroke sequence can be used: In RPN mode: 4 \ 7 z f4 In algebraic mode: 4 z 7 ³ f4 Figure 1 f6 Figure 2 f7 Figure 3 Note that an automatic rounding occurs with the representation of the number, but internally there is always a ten-digit mantissa and a two-digit exponent of ten for each number. If it is necessary to check the mantissa of the number in display: fX (hold for as long as needed) Figure 4 hp calculators - 2 - HP 12C Platinum Operating modes and clearing procedures - Version 1.0

• • • There is also a scientific notation mode that shows numbers with seven significant digits and the exponent of ten. This is useful if a number is too large to be displayed normally or if a number needs to be displayed in this manner to be consistent with other values. f. Figure 5 If there is a need to change the radix mark from dot (default) to comma and conversely, the HP12C Platinum allows toggling from one to the other with the following sequence: with the calculator off, press and hold .; turn the calculator on; release .. Figure 6 Settings and annunciators Figure 7 shows all annunciators other than ALG and RPN (that affect the calculating mode) that may become visible in an HP12C Platinum display when in normal operation: Figure 7 Their meanings are: the batteries are nearly exhausted and must be replaced; ALG RPN Algebraic and RPN mode annunciators, respectively. f or g the corresponding f or g key was pressed and its action is still active; press fX to override BEGIN the keystroke sequence g× was performed to indicate that payments occur in the beginning of the composition periods; to change back to end mode and deactivate the annunciator, press gÂ. D.MY the keystroke sequence gÔ was performed to indicate that dates are entered and shown in DD.MMYYYY format; to changes modes to M.DY and deactivate the annunciator, press gÕ. C the keystroke sequence ?É was performed to indicate that odd-periods are considered with compound interest rate when TVM operations are performed; press ?É again to toggle the annunciator condition and use simple interest for odd-periods. PRGM either program mode is active or a program is running. If program mode is active, press fs to return to normal operation and deactivate the annunciator; if is flashing in the display then a program is being executed and pressing t will stop it. hp calculators - 3 - HP 12C Platinum Operating modes and clearing procedures - Version 1.0

Note that if is flashing in the display and the PRGM annunciator is not shown, then an internal function is being performed and pressing t will not stop it. Memory Organization In the HP12C Platinum, memory is organized as a set of registers that can hold a valid number representation. There are a total of 20 data registers, R0 to R9 and R.0 to R.9, that are available for use. There are 309 program lines available to the user for holding program instructions. If programs are entered that are larger than this, registers are converted as needed into 8 program lines each, beginning with R.9 and working down through R7, for a maximum of 400 program lines. Registers R0 to R9 and R.0 to R.9 are "general purpose" registers, and they can be accessed either directly by the user or by some internal functions. The shaded area represents the registers that can be automatically converted into program steps. Although registers R1 to R6 are general purpose registers as any other, their contents are used by statistical functions. Financial registers n, ¼, $, P and M are used by TVM, Bond, Depreciation and Cash- Flow functions, but can also be used to hold any valid number. n i PV PMT FV Stack Registers Cash flow Nj T R0 CF0 N0 Z (n) R1 CF1 N1 Y (Σx) R2 CF2 N2 X Σ (Σx2) R3 CF3 N3 (Σy) R4 CF4 N4 L (Σy2) R5 CF5 N5 (Σxy) R6 CF6 N6 R7 CF7 N7 R8 CF8 N8 ... ... ... R.8 CF18 N18 R.9 CF19 N19 --- CF20 N20 ... ... ... --- CF28 N28 --- CF29 N29 N30 ... These program steps are also available, as you key them in Permanently available program steps Figure 8 hp calculators - 4 - HP 12C Platinum Operating modes and clearing procedures - Version 1.0

• • • How to selectively clear memory contents The "master clear" of the HP12C Platinum is accomplished when the following sequence is executed: with the calculator off, press and hold -; turn the calculator on; release -. If the operation is successful, the display shows: Figure 9 The HP12C Platinum memory contents now match the ones shown in Figure 8. It is possible to clear specific parts of the HP12C Platinum memory with the use of the clearing functions under -CLEAR-, on the keyboard. The different functions included are: f² clears the contents of registers R1 to R6 and the stack registers X, Y, Z and T to 0.00 without changing any other register contents. This allows new statistic summations to be collected. fÎ If the calculator is in program mode (PRGM annunciator on), fÎ clears the first eight program steps to g(000 (Step 008 would appear as ) and frees all registers used by programs for data storage, if any. If the calculator is in normal (run) mode, fÎ only positions the program memory to step # 000. fG clears the five financial registers n, ¼, $, P and M to zero. fH clears all registers containing valid numbers to their default contents, as shown in Figure 8. fH does not clear any program instruction, even if they are stored in registers converted to program steps. fX clears f annunciator and any partial keystroke sequence (:, ?, ?+, g(, :g, etc) hp calculators - 5 - HP 12C Platinum Operating modes and clearing procedures - Version 1.0