Jazz DV152 Instruction Manual

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC part 15.105 Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Turn On/Off 1. Press & hold down " " to turn camcorder on. 2. Press " " to turn camcorder off. Note: Camcorder will power off after 1 minute if not in used. Change Mode Press " " to change mode between video record, still photo capture and playback. Record/Capture 1. Press " " to begin video recording or take a photo. 2. Press " " again to stop video recording. Note: Insert 2 fresh AA batteries and SD (or MMC) card to operate the camera. Change Resolution Press " " to change resolution. Zoom 1. Press " " to zoom in. 2. Press " " to zoom out. Playback 1. Press " " to enter playback mode. 2. In playback mode, press " " or " " to select another file. 3. Press " " to begin or to stop playing video, and press " " or " " to zoom in/out photo. 4. When zoomed in press " " or " " to enter PAN Mode to view image Delete 1. In playback mode, press " " and “Delete Current?” will appear on display screen. 2. Press " " again and “Delete All?” will appear on display screen. 3. Press " " to confirm. Press any other button to cancel. Change Batteries 1. Press “ ” switch to release the battery cover, slide down the battery cover to remove it. 2. Remove used batteries. 3. Reinstall two fresh AA batteries, align “+”, “-” terminals as indicated. 4. Close the battery cover.

USB ejector Strap Holder Battery Cover

a) Installing Batteries and Powering ON Press “ ” switch to release the battery cover. Slide down and remove the battery cover. Insert two new AA alkaline batteries. Note polarity on battery terminals. Slide and close the battery cover. Press and hold down the power switch until LCD panel shows that camera is turned ON b) Installing SD/MMC Card Turn your camcorder OFF before inserting / removing the SD/MMC Card (maximum 2GB) Insert the SD Memory card into the SD/MMC Card Slot. Check card’s alignment according to position diagram on the camera before inserting. Push it down until the card stays latched. Do not force card during insertion – forcing may damage SD card and camera as well. Push and release inserted card when you wish to remove or replace the card. Note that the SD Card has a tiny LOCK switch on the side. Set the switch on the card to un-LOCK; only this unlocked position will allow you to store recorded videos and still pictures on the SD Memory Card. c) Selecting Video / Still Pictures Resolution You can select High or Low resolution for recording videos or taking still pictures. Press " " resolution switch selecting desired resolution. LCD screen will display “Hi” or “Lo” indicating HIGH or LOW resolution selected.

The SD card must be installed if you wish to record video or take still pictures. Press " " to scroll and select Video Recording or Still photo capture mode. Note related icons visible in left upper corner onto LCD screen. Press " " to begin Video Recording or take a Still Picture. Press " " again to stop Video Recording. e) Playback Press " " to scroll and enter the Playback mode. Press " " or " " (left or right) buttons to select desired Video or Still Picture file. Press " " (down button) to enter “THUMBNAIL MODE” to view multiple files. Then scroll to desired file and press " " to select Press " " to start playing video, press this button again to stop. Press " " or " " to zoom in/out of a Still Picture When you have zoomed in, press " " or " " (left or right button) to enter “PAN MODE”. Then pressing any direction keys will move the enlarged image in any direction so you may view selected picture segment. To exit from “PAN MODE”, press " " button.

Select the Playback mode, press " " and “Delete Current?” will appear on LCD screen. Press " " to confirm deleting current Video or Still picture. Press any other button to cancel “delete” function. Press " " twice and “Delete All?” will appear on display screen. Press " " to confirm deleting all Video or Still Pictures. Press any other button to cancel “delete” function. Connect To PC, Download Video/ Photos and TV Output Please install bundled programs from supplied installation CD before connecting camcorder with PC for the first time 1. Insert supplied CD into computer's CD ROM 2. Follow instruction and install programs; see more information inside "How to upload your video clips to YouTube" Connect to PC 1. Press and then slide up the switch to extend USB connector. Turn the camcorder ON. 2. Insert camcorder USB connector into USB port on computer, or use supplied USB extension cable to make connection. Download Video/Photos From Camcorder To PC 1. After connecting to computer, go to "My Computer” and open the "Removable Disc." The photos or videos will be saved in the \DCIM\ 100MEDIA folder in the removable disc. Choose the desired photo/video in the 100MEDIA folder and copy (drag with mouse) it into the target folder in your computer.

3. Use ArcSoft PhotoImpression and VideoImpression to edit videos and photos. 4. Use ArcSoft MediaImpression to upload your videos to YOUTUBE site. TV Output 1. Plug in TV cable: Insert single-connector end to camcorder. Connect the end with double-connectors to video (yellow) and to audio (red or white) input jack on TV. 2. Turn on TV and camcorder. 3. Switch mode on TV to select video input (see your TV manual for instructions). How to upload your video clips to YouTube 1. Install the ArcSoft MediaImpression program Insert the CD-ROM into the computer’s CD-ROM drive. The auto-run screen will appear. Click “ Install MediaImpression”

computer.） Follow on-screen instructions and complete installation

2. Using ArcSoft MediaImpression Connect your camcorder to the computer. Double click MediaImpression icon on the Desktop. The MediaImpression software main screen will open on the computer’s desktop: Click Import Option on the main screen and enter into “Import” screen. Then select the files in the camcorder

Option. After importing the file has been completed, click on the “ Importing… ” window and enter into “MediaBrowser” window. Note: On the main screen, you can also click other options such as to enter into

Select the video you wish upload to You Tube on“MediaBrowser”screen and then click option to access your YouTube log-in screen.

underneath to save the Username and Password so that you do not need to input these data next time). Then click option. When“Upload to YouTube”screen appears, fill in Title, Description, etc. Then click option and start uploading selected video. Click “Cancel” if you wish to stop upload, otherwise continue for successful uploading.

Product specifications: Image sensor: 300,000pixels Function mode: Recording Video, Capture Still Images, Play back, Mass storage device Resolution: Video: 640×480 (30fps); 320×240 (30fps) Photo: 640×480, 320×240 Lens: F2.8 f=3.0mm Focus range: 1.2m (4 feet) to infinity Digital Zoom: 4× LCD display: 1.5 inch (480x240) TFT LCD White balance: Auto Exposure: Auto File format: AVI/JPEG Video out: PAL Storage media: Uses SD/MMC card (max. 2GB) – not supplied USB port: USB2.0 port Power supply: Uses two AA Alkaline batteries – not supplied System Requirements: Operation System Microsoft Windows 2000,XP,Vista CPU Above Intel PIII800 or CPU of equal performance Memory Above 256 MB Sound card and display card Support DirectX8 or above CD-ROM 4X speed or above Hard Disk 1GB space above useable Other One standard USB 1.1 or USB 2.0 port