HSM 104.3 Operating Instructions

We provide a warranty for the device in accordance with our general sales and delivery terms. This warranty excludes wear, damage due to improper handling, natural depreciation, and actions taken by third parties. Shredding Capabilities: 2. Machine components operating instructions 1 Warning advice 2 Automatic start stop control 3 Rocker switch 4 Cover 5 Name plate 6 Caution label 7 Bottom frame 8 Shredded material container 9 Paper feed opening 4 9 3 1 5 6 2 8 7 STANDARD PRODUCT WARRANTY Quality is part of the company philosophy and all products are manufactured to the highest quality standards. All technical data and measurements are approximate values and based upon single shift operations. All products are subject to different limits and specifications due to operation length, paper size, grain, weight, misuse/abuse and power configurations. Prior to operation read the Manufacturer’s Operating Instructions included with this product. This will help ensure all precautions are taken to avoid cancellation of the manufacturer’s warranty. The manufacturer warrants that any new products sold will be free from defects in material and workmanship when used under specified and normal operating conditions. This warranty is void if repairs are necessitated by accidents, misuse, abuse, water damage or fire. The capabilities of all products are in each specification flier. Exceeding model specifications causing product failure is not covered by this warranty. Modifications, alterations and repairs must be performed by an authorized technician. Lubrication for cross cut shredders is required every fifteen to thirty minutes of operation, to maintain top working condition and this warranty. Office Shredders Parts and labor to repair any failure caused by defect is limited to two (2) years from date of invoice. Cutting Rollers are warranted to be free of manufacturer defects for twenty (20) years from date of invoice or warranty registration date. NOTES: • Freight or transportation damage is not classified as a warranty repair in any case. • Proof of purchase invoice is required from the end-user for warranty validation or warranty registration date. • All parts under warranty will be shipped and invoiced using standard costs and will be credited for the full amount only when the defective part is returned. • IT IS RECOMMENDED THAT A MAINTENANCE AGREEMENT BE UTILIZED TO SUPPLEMENT ALL WARRANTIES. ec 1/4"

• Read all instructions before start-up of the paper shredder. Save these instructions for later use. • Follow all warnings and instructions marked on the product! • Make sure no liquid is spilled on or in the paper shredder. • If the shredder is damaged or does not function properly, switch the device off, pull out the power plug and inform our service engineers. • Keep paper shredder out of the reach of children. • This shredder should be operated only with an operator in attendance. Risk of injury! Do not reach into the paper feed slot. Risk of injury from slivers! Wear protective goggles when destroying hard credit cards. Risk of injury by pulling in! Keep long hair, loose articles of clothing, ties, scarves, jewelry etc. away from feed opening. Material with the tendency to form loops, e.g. tapes, strapping material, etc. must not be shredded. Before changing the location, cleaning or anything else other than normal operation turn off and unplug the paper shredder! Mainte­nan­ce and ser­vi­ce work may be per­for­med on­ly by: • Cu­sto­mer ser­vi­ce • Spe­cial­ly trai­ned staff (e.g. qua­li­fied ele ctri­cians) • An authorized ser­vi­ce tech­ni­cian 4. Scope of delivery • Paper shredder, ready for connection, in carton packing • 5 bags for shredded material • Special cutting block oil 1.7 oz. (cross cut) • Operating instructions Acces­so­ries: • Bag for shredded material • Special cutting block oil 12 oz., 16 oz., and 1 gallon. Call for more information 8. Maintenance and care Cleaning: • Switch off the shredder, pull out the power plug. • When cleaning only use a soft cloth and a mild soap-water solution. Never use scouring agents, cle aning fluid, petrole um or thinners. When the cutting capacity drops or the noise increases (Cross cut): • Switch paper shredder off: Tap rocker switch pos. 2. • Spray special cutting block oil through paper feed opening across the whole width of the cutting system blades. • Run cutting system backwards (pos. 2) without fee ding paper. • Paper dust and particles are shaken off. 2 2 operating instructions 9. Technical Data Technical and optical modifications reserved. Cutting type Strip cut Cross cut Shred size 1/4" 1/8" 1/16" 1/8” x 1 1/8” 1/16" x 5/8" Security level DIN 32757 – 1 2 2 3 3 4 Cutting ca­pa­ci­ty (shee ts), DIN A4 70 g/m2 22 - 24 16 - 18 12 - 14 12 - 14 9 - 11 Weight 25 lbs. 28 lbs. Cutting speed 16 ft./min. 18 ft./min. Noise level (Idle running/ load) 53 dB(A) / 59 - 63 dB(A) Lo­ading width 9.5" Voltage 115 V, 60 Hz Power for the maximum number of sheets 440 W Dimensions W x D x H 14.7" x 11" x 23" Volume of shredded material bag 8.7 gallons IMPORTANT Regular Oiling Instructions After 15 to 30 minutes of continuous use, the cutting cylinders must be oiled. To do this, run the shredder in reverse and squirt oil the length of the cutting cylin- ders twice. Squirt bottle of oil is provided with every shredder. Automatic oilers are available and recommended for cross-cut shredders. OILING and REVER- SING the cutting cylinders regularly is critical to maintain the life expectancy and sheet copacity of the shredder.

source. • The ventilation slots must not be blocked or covered and they must be at a distance of at least 4” away from walls or furniture. • Make sure the power plug is easily accessible. • Before plugging in the power plug, check that the voltage and frequency of your local power supply correspond to those stated on the type plate. 6. Put­ting in­to ope­ra­ti­on Switching the paper shredder on • Press rocker switch pos. 1. • Rocker switch locks in. • Paper shredder is ready for operation (standby). Fee d paper See “Technical Data” for sheet capacity. • The shredding pro­cess is star­ted by the automatic start stop control in the paper feeding opening. • Paper is pulled into cutting system and cut. • When the paper fee­ding opening is free again, the cut­ting sy­stem au­to­ma­tical­ly swit­ches off af­ter app­rox. 3 sec. and returns to standby. Swit­ching paper shredder off • Tap rocker switch pos. 2. • Rocker switch resets to zero position. 1 2 7. Troubleshooting Pa­per jam You have fed in too much paper. Caution! Do not press rocker switch alternately forwards/backwards (pos. 1 / pos. 2): Cutting unit can be damaged. • Press and hold down rocker switch pos. 2. • Pa­per is pus­hed out. • Se­pa­ra­te pa­per stack. • Press rocker switch pos. 1. • Feed pa­per successively. Cut material container full • Paper shredder switches off Empty the cut material container, because if it is too full, malfunctions can occur in the cutting system • Tap rocker switch pos. 2. • Empty full shredded material container. Shredded material container contact interrupted • Paper shredder switches off. • Check whether shredded material container is correctly inserted in bottom frame. If other faults occur, please check the following before calling our customer service: • Is power plug in­ser­ted? • Is rocker switch tur­ned on? • Is the mo­tor over­lo­aded? al­low mo­tor to cool down for 15 - 20 min. 2 1 2 1 2