Ingersoll-Rand SERIES 5020 Operation And Maintenance Manual

performing maintenance on this tool. Always turn off the air supply and disconnect the air supply hose before installing, removing or adjusting any accessory on this tool or before performing any maintenance on this tool. LUBRICATION Each time a Series 5020 or 5040 Torque Control Impactool is disassembled for maintenance and repair or replacement of parts, lubricate the tool as follows: 1. Using Ingersoll–Rand No. 100 Grease, coat only the jaws of the Hammer (66) and the jaws of the Anvil (75or 79). Apply a thin film of No. ...

6. To decrease the delivered torque, rotate the Sleeve clockwise (when facing the square driver) one or more numbers and slide it back into full engagement with the teeth on the Torsion Bar and Anvil. To increase the delivered torque, rotate the Sleeve counterclockwise (when facing the square driver) one or more numbers and slide it back into full engagement with the teeth on the Torsion Bar and Anvil. 7. Turn the Jig Adjusting Screw counterclockwise until the tension is released and there is play in the Torque Jig Arm. 8. Loosen the Eyebolt Thumb Nut and remove the t ...

For Series For Series 5020 5040 75 Anvil (for Non–Detachable Torsion Bars) for 5020T (5/16” square) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5020T–726 ––– for 5040T (7/16” square) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ––– 5040T–726 Quick Change Anvil Assembly (for 5020TDQ or 5040TDQ) . . . . . . . . . . . . . . . . . . . 5020–A926–7 5040–A926–7 79 Quick Change Anvil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

down on the Hammer, against the compression of the Spring, until the cam grooves in the gear frame shank are exposed. 7. Place a Cam Ball (67) in each cam grove and enter the ends of the 4U–30B Hammer Assembly Tool in the small, diametrically opposite holes in the hammer wall. Squeeze the Assembly Tool while releasing the press pressure and the Tool will hold the assembly together. 8. Invert the assembly and stand it on a workbench so the Planet Gear Frame is forced upward as far as the Cam Balls will permit. Inse ...

(Dwg. TPD1337) PART NUMBER FOR ORDERING For Series For Series 5020 5040 125 Horizontal Hanger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5020–366 5040–366 126 Horizontal Hanger Spacer (2) for Tools with Aluminum or Steel–Nosed Hammer Case . . . . . . . . . . . . . . . . . 504–140 504–140 for Tools with Ductile Iron Hammer Case . . . . . ––– 4U–58 127 Horizontal Hanger Cap Screw (2) (for Tools with Aluminum Hammer Case) . . . . . . . . . . . . . . . . . . . . . . . . . . 504–376A 504–376A 128 ...

6. To decrease the delivered torque, rotate the Sleeve clockwise (when facing the square driver) one or more numbers and slide it back into full engagement with the teeth on the Torsion Bar and Anvil. To increase the delivered torque, rotate the Sleeve counterclockwise (when facing the square driver) one or more numbers and slide it back into full engagement with the teeth on the Torsion Bar and Anvil. 7. Turn the Jig Adjusting Screw counterclockwise until the tension is released and there is play in the Torque Jig Arm. 8. Loosen the Eyebolt Thumb Nut and remove the t ...

For Series For Series 5020 5040 75 Anvil (for Non–Detachable Torsion Bars) for 5020T (5/16” square) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5020T–726 ––– for 5040T (7/16” square) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ––– 5040T–726 Quick Change Anvil Assembly (for 5020TDQ or 5040TDQ) . . . . . . . . . . . . . . . . . . . 5020–A926–7 5040–A926–7 79 Quick Change Anvil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...