Icom SM-26 Instructions

SM-27 desktop microphone. These are unidirectional, dynamic microphones designed for base station operation with an Icom transceiver. Please thoroughly read these instruc tions before using the microphone. PRECAUTIONS CAUTION: NEVER expose the microphone to rain, snow or any liquids. CAUTION: NEVER let metal, wire, etc. touch any internal part of the microphone. CAUTION: NEVER touch or operate the desktop microphone with wet hands. DO NOT place the microphone in exces sively dusty environments or in direct sun light. DO NOT use harsh solvents such as ben zine or alcohol to clean the microphone, as they can damage the microphone's sur faces. Place the microphone in a secure place to avoid inadvertent use by children. This microphone is for the specified Icom transceivers only! — The microphone can not be used with a non-lcom transceiver since the power is supplied by the connect ed transceiver. About CE C€ The SM-26/SM-27 comply with the essential require ments of the 2004/108/EC di rective for Electromagnetic Compatibility. SPECIFICATIONS Microphone type Power requirements Current drain Dimensions Cable length Weight (approximately): SM-26 SM-27 : Unidirectional dynamic microphone (preamp built-in) : 8 V DC (supplied by the transceiver) : Less than 10 mA : 70(W) x 169(H) x 167(D) mm; 23A(W) x 62Vfc(H) * 69/ie(D)in (Cable is not included) : 30 cm ±2 cm; 1113/i6 in ±2%2 in 390 g; 13.8 oz 400 g; 14.1 oz All stated specifications are subject to change without notice or obligation. Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries. SM-26 PART NAMES AND FUNCTIONS Front view Microphone O PTT SWITCH [PTT] Push to transmit; release to receive. © MONITOR SWITCH [MONITOR] Activates the Monitor function. See 'MONITOR FUNCTION' below for more details. © MONITOR LOCK [LOCK] While holding down the [MONITOR] switch, slide [LOCK] to continuously keep the [MONITOR] switch down. Slide [LOCK] back to release the [MONITOR] switch. • Bottom view O MIC GAINVOLUME [VOL] Rotate to adjust the microphone out put level. • Use this control as an addition to the transceiver's microphone gain setting, if the connected transceiver has a mi crophone gain control. YA Rotating the control too far counter w clockwise may result in an output yy level that is too high and distort the V/t transmit signal. MONITOR FUNCTION •The [MONITOR]switch can be used to turn ON the hanger function (the [MONITOR] switch is connected to the MIC-hanger line). •You can assign the [MONITOR] switch function to "Monitor," "Scan" or "Priority," de pending on the transceiver's programming. Icom Inc. 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan To use the [MONITOR] switch for the Moni tor function, the transceiver must be pro grammed using the appropriate cloning software: in the Key and Display screen, set the Hanger Action Moni item to ON. Count on us! A-6862X-1 EX Printed in Taiwan ©2010 Icom Inc.

Front view icrophone O PTT SWITCH [PTT] Push to transmit; release to receive. 0 PTT LOCK [LOCK] While holding down the [PTT] switch, slide [LOCK] to continuously transmit without having to hold down the [PTT] switch. Slide [LOCK] back to stop trans mitting and switch to receive. • Bottom view Q MIC GAIN VOLUME [VOL] Rotate to adjust the microphone out put level. • Use this control as an addition to the transceiver's microphone gain setting, if the connected transceiver has a mi crophone gain control. VA Rotating the control too far counter y/ clockwise may result in an output w level that is too high and distort the //. transmit signal. O PLUG PIN ASSIGNMENTS The pins are described from the direction of the arrow in the illustration. No connection © Microphone output (2)8 V DC input 3 No connection © GND (Microphone ground) -4-!— G GND (PTTground) 5 PTT 5 No connection