Goldair GCPF401DR Operating Instructions Manual

Thank you for choosing this Goldair Platinum product. This Goldair appliance has been designed and manufactured to high standards of engineering and with proper use and care, as described in this leaflet, will give you years of useful service. Please read these instructions carefully and keep them for future reference. TECHNICAL SPECIFICATION Model: GCPF401DR Supply: 220 - 240VAC 50Hz Wattage: 60W 1. Use only the voltage specified on the rating plate of the appliance. 2. Keep all objects at least 1 Metre from the front, sides and rear of the appliance 3. This appliance is intended for household use only and not for commercial or industrial use. 4. Use this appliance only as described in this manual. Any other use is not recommended by the manufacturer and may cause fire, electric shock or injury. 5. The common cause of overheating is deposits of dust or fluff in the appliance. Ensure these deposits are removed regularly by unplugging the appliance and vacuum cleaning the air vents and grills. 6. Always unplug appliance when not in use. 7. When the appliance has been unpacked, check if for transport damage and ensure all parts have been delivered. If parts are missing of the appliance has been damaged, contact the CDB Customer Services Team. 8. If your appliance does not work, or is not working properly, contact the place of purchase. Repair work on the appliance by unqualified persons can cause serious risk to the user. 9. Ensure hands are dry before handling the plug or the Fan. 10. Carry out regular checks of the supply cord to ensure no damage is evident. 11. Children should be supervised to ensure that they do not play with the appliance. 12. Ensure that the cord is fully extended (not coiled) while in use. 13. Avoid contact with the moving parts. Keep hands, hair, clothing, away from blade of the Fan during operation to reduce the risk of injury to person and/or damage to the Fan. 14. Switch off and use handles provided when moving. 15. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge, unless they are supervised or have been given instruction concerning the use of the Fan by a person responsible for their safety. 16. Never Place appliance close to radiant heat source. 17. Never Operate in areas where petrol, paint or other flammable liquids are used or stored. 18. Never Use the appliance to dry clothes. 19. Never Insert or allow foreign objects to enter any ventilation or exhaust opening, as this may cause an electric shock, fire or damage to the appliance. 20. Never use abrasive cleaning products on this appliance. Clean with a damp cloth (not wet) rinsed in hot soapy water only. Always remove plug from the mains supply before cleaning. 21. Never connect the appliance to mains supply until completely assembled and adjusted. 22. Never Remove plug from power socket until the appliance has been switched off. 23. Never Remove plug from power socket by pulling cord – always grip plug. 24. Never Twist, kink or wrap the cord around the appliance, as this may cause the insulation to weaken and split. Always ensure that all cord has been removed from any cord storage area and is unrolled before use. 25. Never use this appliance in the immediate surrounds of a bath, a shower, or a swimming pool or other liquids. The appliance must not be immersed in any liquids. 26. Due to the risk of injury, never use this appliance for any purpose other than its intended use. This appliance is intended for use in household and similar applications such as staff kitchen areas in shops, offices and other working environments; farm houses, by clients in hotels, motels and other residential type environments, bed and breakfast type environments 27. Never use this appliance outdoors. 28. The use of an extension cord, power board, or external timer is not recommended with this unit. 29. Never operate the appliance with a damaged cord or plug, after it malfunctions, or if it has been damaged in any manner. Have the appliance checked and repaired by a qualified electrician if repair is necessary. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

7. Motor housing 8. Axis 9. Rear guard 10. Guard nut 11. Fan blade 12. Blade nut 13. Front guard 14. Remote

Height adjustment

pushing the adjustment button (6) and moving the pipe to the desired height. Attach the rear guard (9) to the front side of the motor housing (7) fasten the guard nut (10) by turning it clockwise until the guard is secured firmly in place on the motor housing. Mount the fan blade (11) onto the Axis (8), slide the blade nut (12) onto the axis and fasten the fan blade by turning it anti-clockwise firmly. Open the front guard clips and slide the front guard (13) onto the axis. Push the round edges of front guard to fit it securely into the rear guard then latch the guard clips down onto the rear guard to lock it into place. Assembling your Fan Always choose a safe location for the Fan, keeping in mind the safety precautions outlined. Ensure all packaging has been removed from the unit before use. This appliance requires no installation, it should be used solely as a portable appliance. ASSEMBLING YOUR FAN: Before using the Fan the base (supplied separately in the carton), must be fitted to the unit. Insert the stand body (3) into the base cover (2) and then fit it to the base plate (1). Lead the power cord through the recess at the back of the base plate and base cover. Press down on the stand body firmly until you hear it click into place on the base plate and cover. Note: Ensure the stand body is completely interlocked with the base unit.

ON/SPEED: Plug into power supply and switch on at the mains. To turn the unit on press On/Speed button. To switch between Low, Medium, or High wind speeds, press the On/Speed button again, the control panel will indicate the working speed of unit by illuminating the corresponding backlight. Press the Stop button and the unit will turn off. REMOTE CONTROL INSTRUCTIONS: The remote control buttons perform the same functions as those on the control panel of the unit. For best results, aim the remote directly at the remote sensor on the front panel of the Fan. The remote has a 6metre range of operation. Replace battery when required by opening the battery compartment on the back of controller. Pull out the battery compartment as shown below. Replace with new battery taking note to match the Plus (+) and Minus (-) from the battery to the controller. The remote will restart when pushed back into the compartment. PRE-PROGRAMMED SETTINGS The unit has 3 pre-programmed settings which can be selected. To switch between the pre-programmed settings, press the Mode button. The display panel will indicate the working setting of unit by illuminating the corresponding backlight. The settings are Normal, Natural, Sleeping: Normal: The unit runs at a constant speed according to the wind speed that has been set. Natural: The wind speed shifts between Low, Medium, High in soft patterns. When the unit is set in High wind speed the Natural setting will cycle the unit through Low, Medium, High speed patterns. When the unit is set in Medium wind speed the Natural setting will cycle the unit through Low, Medium speed patterns with brief High speed. When the unit is set in Low wind speed the Natural setting will cycle the unit through Low, Medium speed patterns. Sleep: The wind speeds shift in a step down progression. When the unit is set in High wind speed the sleep setting will cycle the unit through High, Medium speed patterns of 30 minutes then remain on Low speed for the remainder of the program. When the unit is set in Medium wind speed the sleep setting will cycle the unit through Medium speed for 30 minutes then remain on Low speed for the remainder of the program. When the unit is set in Low wind speed the sleep setting will remain on Low speed for the remainder of the program These pre-programmed settings cannot be modified.

TIMER: The Timer function allows the Fan to operate continuously from 0.5 – 7.5 hours before automatically turning Off. The Timer can be operated in any mode. Press the TIMER Button on the control panel (or remote) once and the Fan will display 0.5 hours. By pressing the TIME Button again you can adjust the desired length of time in increments. The corresponding length of time will illuminate on the control panel displaying your selected time. For example: If the Timer is programmed to operate for 3 hours, the 2 hour and 1 hour light will be illuminated. To stop the Timer function, press TIMER button until time indicators are OFF. COLOUR LIGHT The colour light featured at the top of the control panel can be turned on or off by pressing the Colour Light button. SWING: When unit is powered on, press the SWING button to oscillate the fan. Press again to fix a stationary angle. To set to desired wind direction, support the stand pipe, hold the motor housing of the fan, and adjust the fan vertically upwards or downwards until a desired angle is reached. CARE AND CLEANING The Fan requires regular cleaning to ensure trouble free operation: Unplug the Fan from the mains supply before cleaning. Ensure that the Fan blade has been allowed to stop down completely before cleaning. Use a damp cloth (not wet) to wipe the exterior of the Fan to remove dust and dirt. Use a vacuum cleaner to remove dust and fluff from around the grills. Never use solutions such as benzene, thinners or polishing agents. Ensure the Fan is dry before plugging back into the mains supply. Do not attempt to dismantle the Fan. There are no user serviceable parts. For service or repair, contact an authorised electrical service technician. Goldair – New Zealand Monday – Friday 8am-5pm Phone +64 (0)9 917 4000 Phone 0800 232 633 [email protected] Goldair – Australia Monday – Friday 8am-5pm Phone +61 (0)3 9336 4423 Phone 1300 465 324 [email protected] SUPPORT AND TECHNICAL ADVICE PROOF OF PURCHASE To receive warranty retain receipt as proof of purchase. (Refer to back of booklet).

used in normal domestic use for a period of two years. In non-domestic use Goldair limits the voluntary warranty to three months. Goldair undertake to repair or replace this product at no charge if found to be defective due to a manufacturing fault during the warranty period. This warranty excludes damage caused by misuse, neglect, shipping accident, incorrect installation, or work carried out by anyone other than a qualified electrical service technician. PLEASE KEEP YOUR RECEIPT AS THIS WILL HELP VERIFY YOUR WARRANTY. The benefits given to you by this warranty are in addition to other rights and remedies available to you under law in relation to the goods or services to which this warranty relates. In Australia, our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. In New Zealand this warranty is additional to the conditions and guarantees of the Consumers Guarantee Act (1993). Two Year Warranty Goldair Two Year Warranty (IMPORTANT: Please complete and retain this warranty card) Name Address Place Of Purchase Date Of Purchase Name Of Product Model Number Attach a copy of the purchase receipt to this warranty card Due to continual design improvements, the product illustrated in this User Manual may differ slightly from the actual product. Goldair – New Zealand CDB Goldair PO Box 100-707 N.S.M.C Auckland Phone +64 (0)9 917 4000 Phone 0800 232 633 www.goldair.co.nz Goldair – Australia CDB Goldair Australia Pty PO Box 574 South Morang Victoria, 3752 Phone +61 (0)3 9336 4423 Phone 1300 Goldair (1300 465 324) www.goldair.com.au