Graco SG3 Instructions Manual

– For applying architectural paints and coatings – 3600 psi (248 bar, 25 MPa) Maximum Working Pressure 246389, A Reversible Tip Guard, 413 Tip GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441 Graco Inc. is registered to I.S. EN ISO 9001

To help prevent a fire and explosion:
Use in an extremely well ventilated area.
Eliminate all ignition sources; such as pilot lights, cigarettes and static arcs from plastic drop cloths. Do not plug or unplug power cords or turn lights on or off in spray area.
Ground Sprayer, object being sprayed, paint and solvent pails.
Hold gun firmly to side of grounded pail when triggering into pail.
Use only conductive airless paint hose.
Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids contain- ing such solvents in pressurized aluminum equipment. Such use could result in a chemical reaction, with the possibility of explosion. WARNING Fluid injection and high pressure hazard: High pressure spray or leaks can inject fluid into the body. To help prevent injection, always:
Engage trigger safety latch when not spraying.
Keep clear of nozzle and leaks.
Never spray without a tip guard.
Do PRESSURE RELIEF if you stop spraying or begin servicing sprayer.
Do not use components rated less than sprayer Maximum Working Pressure.
Never allow children to use this unit. If high pressure fluid pierces your skin, the injury might look like “just a cut”. but it is a serious wound! Get immediate medical attention. WARNING

sprayer OFF. Unplug. 2. Set trigger lock. PRESSURE RELIEF 3. Remove tip. 4. Remove trigger lock. Follow 1–7 when you stop spraying. 5. Trigger gun into grounded metal bucket. 6. Set trigger lock. 7. Turn Prime/Spray valve to PRIME.

2. Loosen tip guard retaining nut. ALIGN SPRAY 3. Turn tip guard horizontally to spray a horizontal pattern. 4. Turn tip guard vertically to spray a vertical pattern.

2. Install tip and guard. ADJUST SPRAY WARNING MISE EN GARDE ADVERTENCIA ADVERTÊNCIA 3. Tighten retaining nut. 4. Remove trigger lock. 5. Trigger gun. 6. Hold gun perpendicular and approximately 12 in. (304 mm) from surface. Move gun first, then pull gun trigger to spray. 7. Slowly increase the pump pressure until coverage is even and uniform.

2. Set trigger lock. 3. Rotate tip 180. CLEAR CLOG WARNING MISE EN GARDE ADVERTENCIA ADVERTÊNCIA 4. Remove trigger lock. 5. Trigger gun into pail or onto ground to remove clog. 6. Set trigger lock. 7. Rotate tip 180.

2. Set trigger lock. 3. Remove tip and guard and disconnect gun from fluid hose. WARNING MISE EN GARDE ADVERTENCIA ADVERTÊNCIA 4. Release trigger lock. REPLACE NEEDLE 5. Squeeze trigger while unscrewing the diffuser. 6. Remove locknut and end cap.

OLD CLEAN 8. Clean internal passages of gun. GREASE SILICON 9. Grease o–rings of new needle using a nonsilicon grease. NEW 10. Guide new needle into gun. LOOSE 11. Install end cap and locknut, loosely.

nonsilicon grease. 13. Grease threads of diffuser/seat. Place gasket on diffuser/seat. Grease Gasket 14. Squeeze trigger while installing gasket and diffuser/seat. Torque to 26–32 ft lb (19–24 Nm). 26–32 ft–lb (19–24 N.m) SILICON

2. Turn locknut clockwise until you see and feel trigger raise slightly. 3. Turn locknut 3/4 turn counterclockwise. NOTE: When needle is properly adjusted, trigger will move freely. ADJUST NEEDLE 3/4 Turn 4. Connect fluid hose, install tip and guard. 5. Prime Sprayer, see sprayer manual. 6. Trigger gun into grounded metal bucket until fluid flows from gun.

8. Set trigger lock. 9. Try to trigger gun. No fluid should flow. 10. If the gun fails either test, relieve pressure, disconnect hose and readjust needle, repeat tests.

23 24 5 10 3 2 2 Included with 33 1 1 32 14 2 2 11 4 9 Parts List Ref. No. Part No. Description Qty. 1 243092 KIT, repair, needle 1 2√ 246391 GUARD, tip, includes 3 1 3 246390 SEAL, cartridge 1 4 195495 GUARD, trigger 1 5 238817 KIT, swivel 1 6√ 218131 FILTER, gun 1 7√ 179733 SEAL, sleeve 1 8 195395 CAP, end 1 9 115483 CAP, end 1 10 115484 PIN, actuator 2 11 195419 HOUSING, needle 1 14 177538 STUD, trigger 1 15√ TIP, spray 1 15a√ TR1413 TIP, spray, cylinder, size 413 1 Ref. No. Part No. Description Qty. 15b√ TR2515 TIP, spray, cylinder, size 515 1 15c√ TR3517 TIP, spray, cylinder, size 517 1 22 113409 RETAINER, guard 1 23 195788 HANDLE, gun 1 24 115485 O–RING 1 26 195390 HOUSING, fluid 1 32 105334 NUT, lock, hex 1 33 243353 KIT, repair, trigger 1 34 222385 WARNING CARD, not shown 1
Replacement Danger and Warning labels, tags and cards are available at no cost. √Keep these spare parts on hand to reduce down time.

Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations. This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or sub- stitution of non–Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco. This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation. THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale. GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in mak- ing any claim for breach of these warranties. In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise. FOR GRACO CANADA CUSTOMERS The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnais- sent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procedures concernées. All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice. Sales Office: Minneapolis International Offices: Belgium, Korea, Hong Kong, Japan GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441 PRINTED IN U.S.A. 39637 10/2002, Revised 10/2004