IFM E89005 Operating Instructions Manual

with two presets LCD positive, green backlighting relay outputs E89005 7390806 / 00 09 / 2017 UK ecomat 200 E89005

2 Contents 1 Preliminary note � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 5 1�1 Symbols used� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 5 1�2 Warning signs used � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 5 2 Safety instructions � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 5 3 Functions and features � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 6 3�1 General description � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 6 3�1�1 Input modes � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 6 3�1�2 Output operations � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 7 3�2 Inputs � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 7 3�2�1 INP A, INP B� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 7 3�2�2 RESET � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 7 3�2�3 GATE � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 7 3�2�4 LOCK INPUT � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 7 3�2�5 MPI� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 7 3�3 Outputs� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 8 3�3�1 Active Outputs � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 8 4 Mounting� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 8 5 Electrical connection� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 9 5�1 Advice on noise immunity� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 9 5�2 Connections � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 10 5�2�1 Signal and control inputs � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 10 5�2�2 Supply voltage and outputs � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 10 6 Operating and display elements � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �11 6�1 Error message � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �11 7 Programming � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 12 7�1 Entering the programming � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 12 7�2 Choice of main menu � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 12 7�3 Entering a submenu � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 12 7�4 Selecting the menu items� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 12 7�5 Setting the menu items� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 13 7�6 Accepting the setting � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 13 7�7 Ending the programming � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 13 7�8 Setting the presets � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 15 7�8�1 Setting via Decade Keys � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 15 7�8�2 Setting via Teach-in function � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 15 7�8�3 Setting the tracking presets (trail) � � � � � � � � � � � � � � � � � � � � � � � � � � 16 7�9 Set Function � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 17 8 Parameters � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 18 8�1 Default parameters� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 18 8�2 Table: Default Parameter Sets � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 18 8�3 Setting the basic function of the device � � � � � � � � � � � � � � � � � � � � � � � � � � 19

3 8�4 Pulse counter � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 20 8�4�1 Input � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 20 8�4�2 Mode � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 21 8�4�3 Config� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 23 8�4�4 Reset mode � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 24 8�4�5 Preset 1 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 24 8�4�6 Preset 2 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 25 8�5 Timer � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 27 8�5�1 Input � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 27 8�5�2 Mode � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 28 8�5�3 Config� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 30 8�5�4 Reset mode � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 30 8�5�5 Preset 1 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 31 8�5�6 Preset 2 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 32 8�6 Tacho/Frequency meter � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 34 8�6�1 Input � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 34 8�6�2 Config� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 35 8�6�3 Preset 1 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 36 8�6�4 Preset 2 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 37 9 Diagrams � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 39 9�1 Input modes � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 39 9�1�1 Pulse counting � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 39 9�1�2 Timing� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 41 9�1�3 Frequency meter � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 42 9�2 Output operations� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 43 9�2�1 Add modes � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 43 9�2�2 Sub modes� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 44 9�2�3 Trail modes� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 45 10 Dimensions� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 46 11 Technical data� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 47 11�1 General Data � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 47 11�2 Pulse counter � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 47 11�3 Tacho/Frequency meter � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 47 11�4 Timer� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 48 11�5 Signal and Control inputs � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 48 11�6 Outputs� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 48 11�6�1 Output 1 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 48 11�6�2 Output 2 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 49 11�7 Supply voltage � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 49 11�8 Sensor supply� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 49 11�9 Climatic Conditions� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 49 11�10 EMC � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 49 11�11 Device safety � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 50 11�12 Mechanical Data� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 50

4 11�13 Connections � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 50 12 Maintenance, repair and disposal� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 50 13 Approvals/standards � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 51 14 Attachement � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 51

5 1 Preliminary note Please read this instruction manual carefully before installation and start-up� Please observe all warnings and advice, both for your own safety and for general plant safety� If the device is not used in accordance with this instruction manual, then the intended protection can be impaired� 1.1 Symbols used ► Instructions > Reaction, result […] Designation of keys, buttons or indications → Cross-reference Important note Non-compliance can result in malfunction or interference� Information Supplementary note 1.2 Warning signs used WARNING Warning of serious personal injury� Death or serious irreversible injuries may result� CAUTION Warning of personal injury� Slight reversible injuries may result� NOTE Warning of damage to property� 2 Safety instructions Please use the device only if its technical condition is perfect� It should be used only for its intended purpose� Please bear in mind safety aspects and potential dangers and adhere to the operating instructions at all times� WARNING If the device is used to monitor machines or processes in which, in the event of a failure of the device or an error made by the operator, there might be the risk of damaging the machine or causing an accident to the operators, then it is your responsibility to take the appropriate safety measures�

6 3 Functions and features The preset counter detects and measures pulses, times and frequencies and offers a wide variety of different operating modes� At the same time, the preset counter processes programmed presets� The application area for this device lies in industrial processes and controls, in the fields of manufacturing lines for the metal, wood, plastics, paper, glass, textile and other like industries� Use for any purpose over and beyond this will be deemed as not in accordance with its intended purpose and thus not complying with the requirements� Overvoltages at the terminals of the device must be kept within the limits of Over- voltage Category II� The device must only be operated when mounted in a panel in the correct way and in accordance with the section "Technical Data" (→ 11 Technical data)� Correct operation of the device requires the mandatory use of the appropriate external safety fuse� Advice concerning the recommended fuseprotection can be found under (→ 11.7 Supply voltage)� The device is not suitable for use in hazardous areas and for areas excluded in EN 61010 Part 1� 3.1 General description ● 6-digit multifunction LCD display ● 2-line LCD-display with annunciators for both the displayed preset and the status of the two outputs ● Simultaneous display of the actual value and of the presets or auxiliary counters ● Backlit display ● Add�/Sub� Preset counter with two presets ● Relay outputs ● Preset entry via the front keys or via the Teach-In function ● Step or tracking preset ● Pulse, frequency, time or batch counter ● Preset counter, Batch counter or Total Counter (cumulative count) ● Set function for pulse and time counter ● Multiplication and division factor (00�0001���99�9999) for pulse counter and frequency meter ● Averaging and Start Delay for frequency meter ● 4-stage RESET-Mode ● 3-stage keypad locking (Lock) ● MPI input for Display Latch, Teach-In function or Set function 3.1.1 Input modes ● Pulse counter: cnt�dir, up�dn, up�up, quad, quad2, quad4, A/B, (A-B)/Ax100% ● Timer: FrErun, Auto, InpA�InpB, InpB�InpB ● Frequency meter: A, A-B, A+B, quad, A/B, (A-B)/Ax100%

7 3.1.2 Output operations ● Add, Sub, AddAr, SubAr, AddBat, SubBat, AddTot, SubTot, Trail, TrailAr 3.2 Inputs 3.2.1 INP A, INP B Signal inputs: function acc� to operating mode� Max� frequency 60 kHz, can be damped in the programming menu to 30 Hz� ● Pulse counter: Count inputs ● Timer: Start input or Start/Stop inputs ● Frequency meter: Frequency inputs 3.2.2 RESET Dynamic reset input: resets the pulse counter or timer to zero (adding mode) or to preset value 2 (subtracting mode)� The reset input can be inhibited in the programming menu� ● Pulse counter: RESET input ● Timer: RESET input ● Frequency meter: no function 3.2.3 GATE Static gate input: function depending on operating mode� ● Pulse counter: no counting while active ● Timer: no time measurement while active (Gate�hi), no time measurement while not active (Gate�Lo)� ● Frequency meter: no counting while active 3.2.4 LOCK INPUT Static keypad lock input for presets or programming� Lock-out level can be set in the programming menu� 3.2.5 MPI Input� Programmable as Display Latch, Set or Teach-In input�

8 3.3 Outputs 2 relay outputs with potential-free contacts (→ 11.6 Outputs)� 3.3.1 Active Outputs An active output will be shown on the display� 6 Outputs 6.1 Output 1 Relay with potential-free make (NO) contact or optocoupler with open emitter and collector 6.2 Output 2 Relay with potential-free make (NO) contact or optocoupler with open emitter and collector. 6.3 Active Outputs An active output will be shown on the display as or . For safety switching the relays or optocoupler outputs can be inverted, i.e. the relay will be de- energized or the optocoupler output disabled when the presets are reached. To do this, the parameters Pr.OUT1 and Pr.OUT2 must be set to (for permanent signal) or or (for timed signal). 7 Programming 7.1 Entering the programming Press the Reset key and Prog/Mode key simultaneously for 3 s � The security prompt appears in the display Programming can be exited again using the Prog/Mode key. Press key T2 to continue with the programming � The security prompt appears in the display Enter the main menu by pressing the Prog/Mode key 7.2 Choice of main menus The menus are selected using the keys T2 (next) and T1 (back) g The sub-menu is opened with the Prog/Mode key and the first menu item is displayed. 7.4 Selecting the menu items The Prog/Mode key is used to select a menu item within the sub-menu 7.5 Setting the menu items The T2 key is used to select the individual settings for the menu items When setting count values, each decade has a key assigned to it. Each time the key is pressed, the value increments by one 7.6 Accepting the setting Pressing the Prog/Mode key causes the current setting to be accepted. Programming then switches to the next menu item. 7.7 Ending the programming During programming, it is possible to exit the programming at each menu item by pressing the reset key. Press the Reset key � The security prompt appears in the display Pressing the Prog/Mode key acknowledges this prompt and causes the programming menu to start again from the beginning. The previously-programmed values are preserved. These can now be changed or checked again. Pressing the decade key T2 selects the termination of the programming � The security prompt appears in the display Seite 6 / 6 Outputs 6.1 Output 1 Relay with potential-free make (NO) contact or optocoupler with open emitter and collector 6.2 Output 2 Relay with potential-free make (NO) contact or optocoupler with open emitter and collector. 6.3 Active Outputs An active output will be shown on the display as or . For safety switching the relays or optocoupler outputs can be inverted, i.e. the relay will be de- energized or the optocoupler output disabled when the presets are reached. To do this, the parameters Pr.OUT1 and Pr.OUT2 must be set to (for permanent signal) or or (for timed signal). 7 Programming 7.1 Entering the programming Press the Reset key and Prog/Mode key simultaneously for 3 s � The security prompt appears in the display Programming can be exited again using the Prog/Mode key. Press key T2 to continue with the programming � The security prompt appears in the display Enter the main menu by pressing the Prog/Mode key 7.2 Choice of main menus The menus are selected using the keys T2 (next) and T1 (back) g The sub-menu is opened with the Prog/Mode key and the first menu item is displayed. 7.4 Selecting the menu items The Prog/Mode key is used to select a menu item within the sub-menu 7.5 Setting the menu items The T2 key is used to select the individual settings for the menu items When setting count values, each decade has a key assigned to it. Each time the key is pressed, the value increments by one 7.6 Accepting the setting Pressing the Prog/Mode key causes the current setting to be accepted. Programming then switches to the next menu item. 7.7 Ending the programming During programming, it is possible to exit the programming at each menu item by pressing the reset key. Press the Reset key � The security prompt appears in the display Pressing the Prog/Mode key acknowledges this prompt and causes the programming menu to start again from the beginning. The previously-programmed values are preserved. These can now be changed or checked again. Pressing the decade key T2 selects the termination of the programming � The security prompt appears in the display Seite 6 For safety switching the relay outputs can be inverted, i�e� the relay will be deenergized when the presets are reached� To do this, the parameters Pr�OUT1 and Pr�OUT2 must be set to 6.1 Output 1 Relay with potential-free make (NO) contact or optocoupler with open emitter and collector 6.2 Output 2 Relay with potential-free make (NO) contact or optocoupler with open emitter and collector. 6.3 Active Outputs An active output will be shown on the display as or . For safety switching the relays or optocoupler outputs can be inverted, i.e. the relay will be de- energized or the optocoupler output disabled when the presets are reached. To do this, the parameters Pr.OUT1 and Pr.OUT2 must be set to (for permanent signal) or or (for timed signal). 7 Programming 7.1 Entering the programming Press the Reset key and Prog/Mode key simultaneously for 3 s � The security prompt appears in the display Programming can be exited again using the Prog/Mode key. Press key T2 to continue with the programming � The security prompt appears in the display Enter the main menu by pressing the Prog/Mode key 7.2 Choice of main menus The menus are selected using the keys T2 (next) and T1 (back) The sub-menu is opened with the Prog/Mode key and the first menu item is displayed. 7.4 Selecting the menu items The Prog/Mode key is used to select a menu item within the sub-menu 7.5 Setting the menu items The T2 key is used to select the individual settings for the menu items When setting count values, each decade has a key assigned to it. Each time the key is pressed, the value increments by one 7.6 Accepting the setting Pressing the Prog/Mode key causes the current setting to be accepted. Programming then switches to the next menu item. 7.7 Ending the programming During programming, it is possible to exit the programming at each menu item by pressing the reset key. Press the Reset key � The security prompt appears in the display Pressing the Prog/Mode key acknowledges this prompt and causes the programming menu to start again from the beginning. The previously-programmed values are preserved. These can now be changed or checked again. Pressing the decade key T2 selects the termination of the programming � The security prompt appears in the display Seite 6 (for permanent signal) or 6.1 Output 1 Relay with potential-free make (NO) contact or optocoupler with open emitter and collector 6.2 Output 2 Relay with potential-free make (NO) contact or optocoupler with open emitter and collector. 6.3 Active Outputs An active output will be shown on the display as or . For safety switching the relays or optocoupler outputs can be inverted, i.e. the relay will be de- energized or the optocoupler output disabled when the presets are reached. To do this, the parameters Pr.OUT1 and Pr.OUT2 must be set to (for permanent signal) or or (for timed signal). 7 Programming 7.1 Entering the programming Press the Reset key and Prog/Mode key simultaneously for 3 s � The security prompt appears in the display Programming can be exited again using the Prog/Mode key. Press key T2 to continue with the programming � The security prompt appears in the display Enter the main menu by pressing the Prog/Mode key 7.2 Choice of main menus The menus are selected using the keys T2 (next) and T1 (back) 7.4 Se 7.5 Se 7.6 A 7.7 E During prog programmin reset key. Seite 6 or 6.1 Output 1 Relay with potential-free make (NO) contact or optocoupler with open emitter and collector 6.2 Output 2 Relay with potential-free make (NO) contact or optocoupler with open emitter and collector. 6.3 Active Outputs An active output will be shown on the display as or . For safety switching the relays or optocoupler outputs can be inverted, i.e. the relay will be de- energized or the optocoupler output disabled when the presets are reached. To do this, the parameters Pr.OUT1 and Pr.OUT2 must be set to (for permanent signal) or or (for timed signal). 7 Programming 7.1 Entering the programming Press the Reset key and Prog/Mode key simultaneously for 3 s � The security prompt appears in the display Programming can be exited again using the Prog/Mode key. Press key T2 to continue with the programming � The security prompt appears in the display Enter the main menu by pressing the Prog/Mode key 7.2 Choice of main menus The menus are selected using the keys T2 (next) and T1 (back) 7.4 S 7.5 S 7.6 A 7.7 E During pro programm reset key. Seite 6 (for timed signal)� See (→ 2 Safety instructions)� 4 Mounting CAUTION Mount the device away from heat sources and avoid direct contact with corrosive liquids, hot steam or similar� ► Remove mounting clip from the device� ► Insert the device from the front into the panel cut-out, ensuring the front-panel gasket is correctly seated� ► Slide the fixing clip from the rear onto the housing, until the spring clamps are under tension and the upper and lower latching lugs have snapped into place�

9 5 Electrical connection WARNING The device must be disconnected from the power supply, before any installation or maintenance work is carried out� AC-powered devices must only be connected to the lowvoltage network via a switch or circuit breaker� Installation or maintenance work must only be carried out by qualified personnel� 5.1 Advice on noise immunity All connections are protected against external sources of interference� The installation location should be chosen so that inductive or capacitive interference does not affect the device or its connecting lines! Interference (e�g� from switchmode power supplies, motors, clocked controllers or contactors) can be reduced by means of appropriate cable routing and wiring� Measures to be taken: ► Connect the terminal 2 (GND) with ground� ► Use only shielded cable for signal and control lines� ► Connect cable shield at both ends� ► The conductor cross-section of the cables should be a minimum of 0�4 mm²� ► The shield connection to the equipotential bonding should be as short as possible and with a contact area as large as possible (low-impedance)� ► Only connect the shields to the control panel, if the latter is also earthed� ► Install the device as far away as possible from noise-containing cables� ► Avoid routing signal or control cables parallel to power lines� ► Cables and their insulation should be in accordance with the intended temperature and voltage ranges�

10 5.2 Connections 9 Connections 9.1 Signal and Control Inputs N° Designation Function 1 24 VDC/80 mA Sensor supply voltage 2 GND (0 VDC) Common connection Signal and Control inputs 3 INP A Signal input A 4 INP B Signal input B 5 RESET Reset input 6 LOCK Keypad lock 7 GATE Gate input 8 MPI User input 9.2 Supply voltage and Outputs 9.2.1 Version with relays N° Designation Function 9 Relay contact C.1 10 Relay contact N.O.1 Output 1 11 Relay contact C.2 12 Relay contact N.O.2 13 Relay contact N.C.2 Output 2 14 AC: 90..260 VAC N~ Supply voltage 15 AC: 90..260 VAC L~ Supply voltage 10 Technical Data 10.1 General Data Display LCD positive backlite 2 x 6-digit Digit height upper line 9 mm lower line 7 mm special characters 2 mm Overload/ Blinking, 1 s Underload Counter loses up to 1 decade no pulses Data retention > 10 years, EEPROM Operation 8 keys 10.2 Pulse counter Count frequency max. 55 kHz (see section 13. frequencies typ.) Response time of the outputs: Relays Add/Sub/Trail < 7 ms With automatic repeat < 7 ms A/B ; (A-B)/A < 29 ms 10.3 Tacho/Frequency meter Frequency range 0,01 Hz to 65 kHz (see section 13. frequencies typ.) Measuring � 76.3 Hz Time interval principle (period measurement) > 76.3 Hz Gate time Gate time approx.13.1 ms Measuring error < 0.1% per channel Response time of the outputs: 1-channel operation < 100 ms @ 40 kHz < 350 ms @ 65 kHz 2-channel operation < 150 ms @ 40 kHz < 600 ms @ 65 kHz 10.4 Timer Seconds 0.001 s ... 999 999 s Minutes 0.001 min ... 999 999 min Hours 0.001 h .. 999 999 h h.min.s 00h.00min.01s ... 99h.59min.59s Min. time measurable 500µs Measuring error < 50 ppm Response time of the outputs: Relays < 7 ms Terminals 5.2.1 Signal and control inputs Terminal Designation Function 1 24 V DC / 80 mA Sensor supply voltage 2 GND (0 VDC) Common connection signal and control inputs 3 INP A Signal input A 4 INP B Signal input B 5 RESET Reset input 6 LOCK Keypad lock 7 GATE Gate input 8 MPI User input 5.2.2 Supply voltage and outputs Terminal Designation Function 9 Relay contact C1 Output 1 10 Relay contact NO1 11 Relay contact C2 Output 2 (changeover contact) 12 Relay contact NO2 13 Relay contact NC2

11 Terminal Designation Function 14 90���260 V AC N Supply voltage 15 90���260 V AC L NO= normally open NC = normally closed C = common 6 Operating and display elements Frequency meter: A , A � B , A + B , quad , A/B , (A-B)/Ax100% Timer: FrErun , Auto , InpA.InpB , InpB.InpB Output operations: Add , Sub , AddAr, SubAr , AddBat , SubBat , AddTot , SubTot , Trail , TrailAr 4-stage RESET-Mode 3-stage keypad locking (Lock) MPI input for Display Latch, Teach-In function or Set function Supply voltage 90 .. 260 VAC 4 Display/Operating elements 5.2 RESET Dynamic reset input: re timer to zero (adding m (subtracting mode). The in the programming me Pulse counter: R Frequency meter: no Timer: R 5.3 GATE Static gate input: functio mode. Pulse counter: no Frequency meter: no Timer: no ac no no 5.4 LOCK INPU Static keypad lock inpu programming. Lock-out programming menu. 5.5 MPI Input. Programmable a Teach-In input. R P T1-6 Reset key [R] Prog/Mode key [P] Decade keys [T���] 8 9 10 11 12 Current count value / main counter Preset value / Total count / Batch counter Run display for Timer Shows which preset value is being displayed Shows which preset output is active Pr Keys necessary for programming the parameters (highlighted in grey) [R], [P], [T1], [T2] 6.1 Error message Err 1 Set value is outside the permitted range�

12 7 Programming 7.1 Entering the programming ► Press [R] and [P] simultaneously for 3 s > The security prompt appears in the display� Programming can be exited again using [P]� permanent signal) or signal). 7 Programming 7.1 Entering the p Press the Prog/Mod for 3 s � Program again usi Press ke programm � Enter the the Prog/ 7.2 Choice of mai The men the keys Seite 6 7 Programming 7.1 Entering the p Press the Prog/Mod for 3 s � Program again usi Press ke programm � Enter the the Prog/ 7.2 Choice of mai The men the keys Seite 6 ► Press [T2] to continue with the programming� > The security prompt appears in the display� 7.1 Entering the p Press the Prog/Mod for 3 s � Program again usi Press ke programm � Enter the the Prog/ 7.2 Choice of mai The men the keys Seite 6 7.1 Entering the p Press the Prog/Mod for 3 s � Program again usi Press ke programm � Enter the the Prog/ 7.2 Choice of mai The men the keys Seite 6 ► Enter the main menu by pressing [P]� 7.1 Entering the p Press the Prog/Mod for 3 s � Program again usi Press ke programm � Enter the the Prog/ 7.2 Choice of mai The men the keys Seite 6 7.2 Choice of main menu ► The menus are selected using [T2] (next) and [T1] (back)� 7.1 Entering the p Press the Prog/Mod for 3 s � Program again usi Press ke programm � Enter the the Prog/ 7.2 Choice of mai The men the keys Seite 6 7.3 Entering a submenu ► The submenu is opened with [P] and the first menu item is displayed� or . For safety switching the rela outputs can be inverted, i.e energized or the optocouple the presets are reached. To Pr.OUT1 and Pr.OUT2 mus permanent signal) or signal). 7 Programming 7.1 Entering the p Press the Prog/Mod for 3 s � Program again usi Press ke programm � Enter the the Prog/ 7.2 Choice of mai The men the keys Seite 6 7.4 Selecting the menu items ► [P] is used to select a menu item within the sub-menu� p Relay with potential-free ma optocoupler with open emitt 6.3 Active Output An active output will be sho or . For safety switching the rela outputs can be inverted, i.e energized or the optocouple the presets are reached. To Pr.OUT1 and Pr.OUT2 mus permanent signal) or signal). 7 Programming 7.1 Entering the p Press the Prog/Mod for 3 s � Program again usi Press ke programm � Enter the the Prog/ 7.2 Choice of mai The men the keys

13 7.5 Setting the menu items ► [T2] is used to select the individual settings for the menu items� Program again usi Press ke programm � Enter the the Prog/ 7.2 Choice of mai The men the keys Seite 6 When setting count values, each decade has a key assigned to it� Each time the key is pressed, the value increments by one� p p p 6.3 Active Outputs An active output will be shown on the display as or . For safety switching the relays or optocoupler outputs can be inverted, i.e. the relay will be de- energized or the optocoupler output disabled when the presets are reached. To do this, the parameters Pr.OUT1 and Pr.OUT2 must be set to (for permanent signal) or or (for timed signal). 7 Programming 7.1 Entering the programming Press the Reset key and Prog/Mode key simultaneously for 3 s � The security prompt appears in the display Programming can be exited again using the Prog/Mode key. Press key T2 to continue with the programming � The security prompt appears in the display Enter the main menu by pressing the Prog/Mode key 7.2 Choice of main menus The menus are selected using the keys T2 (next) and T1 (back) sub menu 7.5 Setting the men The T2 key individual se items When settin decade has Each time th the value in 7.6 Accepting the se Pressing the causes the c accepted. P switches to t 7.7 Ending the prog During programming, it is poss programming at each menu ite reset key. Press the R � The app Pressing the acknowledg causes the p to start agai The previou values are p now be chan again. Pressing the selects the t programmin � The app Seite 6 7.6 Accepting the setting ► Pressing [P] causes the current setting to be accepted� Programming then switches to the next menu item� Program again usi Press ke programm � Enter the the Prog/ 7.2 Choice of mai The men the keys Seite 6 7.7 Ending the programming During programming, it is possible to exit the programming at each menu item by pressing the reset key� ► Press [R]� > The security prompt appears in the display� ac e ou pu be s o o e d sp ay as or . For safety switching the relays or optocoupler outputs can be inverted, i.e. the relay will be de- energized or the optocoupler output disabled when the presets are reached. To do this, the parameters Pr.OUT1 and Pr.OUT2 must be set to (for permanent signal) or or (for timed signal). 7 Programming 7.1 Entering the programming Press the Reset key and Prog/Mode key simultaneously for 3 s � The security prompt appears in the display Programming can be exited again using the Prog/Mode key. Press key T2 to continue with the programming � The security prompt appears in the display Enter the main menu by pressing the Prog/Mode key 7.2 Choice of main menus The menus are selected using the keys T2 (next) and T1 (back) The T2 k individua items When se decade h Each tim the value 7.6 Accepting the Pressing causes th accepted switches 7.7 Ending the pr During programming, it is p programming at each menu reset key. Press the � Pressing acknowle causes th to start a The prev values ar now be c again. Pressing selects th programm � Seite 6 or . For safety switching the relays or optocoupler outputs can be inverted, i.e. the relay will be de- energized or the optocoupler output disabled when the presets are reached. To do this, the parameters Pr.OUT1 and Pr.OUT2 must be set to (for permanent signal) or or (for timed signal). 7 Programming 7.1 Entering the programming Press the Reset key and Prog/Mode key simultaneously for 3 s � The security prompt appears in the display Programming can be exited again using the Prog/Mode key. Press key T2 to continue with the programming � The security prompt appears in the display Enter the main menu by pressing the Prog/Mode key 7.2 Choice of main menus The menus are selected using the keys T2 (next) and T1 (back) individua items When se decade h Each tim the value 7.6 Accepting the Pressing causes th accepted switches 7.7 Ending the pro During programming, it is po programming at each menu reset key. Press the � Pressing acknowle causes th to start ag The prev values ar now be c again. Pressing selects th programm � Seite 6 ► Pressing [P] acknowledges this prompt and causes the programming menu to start again from the beginning� > The previously-programmed values are preserved� These can now be changed or checked again� energized or the optocouple the presets are reached. To Pr.OUT1 and Pr.OUT2 mus permanent signal) or signal). 7 Programming 7.1 Entering the p Press the Prog/Mod for 3 s � Program again usi Press ke programm � Enter the the Prog/ 7.2 Choice of mai The men the keys Seite 6 ► Pressing [T2] selects the termination of the programming� > The security prompt appears in the display� y p optocoupler with open emitt 6.2 Output 2 Relay with potential-free ma optocoupler with open emitt 6.3 Active Output An active output will be sho or . For safety switching the rela outputs can be inverted, i.e energized or the optocouple the presets are reached. To Pr.OUT1 and Pr.OUT2 mus permanent signal) or signal). 7 Programming 7.1 Entering the p Press the Prog/Mod for 3 s � Program again usi Press ke programm � Enter the the Prog/ 7.2 Choice of mai The men energized or the optocoupler output disabled when the presets are reached. To do this, the parameters Pr.OUT1 and Pr.OUT2 must be set to (for permanent signal) or or (for timed signal). 7 Programming 7.1 Entering the programming Press the Reset key and Prog/Mode key simultaneously for 3 s � The security prompt appears in the display Programming can be exited again using the Prog/Mode key. Press key T2 to continue with the programming � The security prompt appears in the display Enter the main menu by pressing the Prog/Mode key 7.2 Choice of main menus The menus are selected using the keys T2 (next) and T1 (back) When se decade h Each tim the value 7.6 Accepting the Pressing causes th accepted switches 7.7 Ending the pro During programming, it is po programming at each menu reset key. Press the � Pressing acknowle causes th to start ag The prev values ar now be c again. Pressing selects th programm � Seite 6

14 ► Pressing [P] acknowledges this prompt and terminates the programming� > The modified settings are saved in the EEPROM� The text SAVE is displayed for 2 s� � Enter the the Prog/ 7.2 Choice of mai The men the keys Seite 6 Pressing acknowle terminate modified the EEPR � 7.8 Programming 7.8.1 Default paramet Note: Th sets hav stored; th required acknowle paramete will be re in the tab The dEF freely pro Menu Pa Default s Paramete Default s Paramete Default s Paramete Freely pr User sett Complete parameter structure and menues see attachement�

15 7.8 Setting the presets 7.8.1 Setting via Decade Keys In programming mode Preset 2 will always be displayed in the lower line� This is except for the output operations AddBat, SubBat,AddTot and SubTot� ► Press [P] until the preset to be changed is displayed� ( the optocoupler disabled when the preset value is reached. Setting the presets Setting via Decade Keys ramming mode Preset 2 will always be ed in the lower line. This is except for the operations AddBat, SubBat,AddTot and t. Press the Prog/Mode key until the preset to be changed is displayed - or . Press any decade key Display switches to the editor mode Set the desired preset value using the decade keys Press the Prog/Mode key to confirm the value and save it Display switches to the editor mode of the next preset or Approx. 3 s after the last press of the decade keys or by pressing the Reset key the new preset value will be accepted and the counter will switch back to operating mode. 7.9.3 Setting the tracking presets (trail) If a tracking preset has been programmed, the value for Preset 2 can be set either via the decade keypad or via the Teach-IN function. However the value for Preset 1 must be entered via the decade keypad. In this instance, it is not possible to use the Teach-In function. 7.10 Set Function Both the pulse counter and the timer can be set to a default value by means of the Set function. Programme the MPI input to SEt Set menu item SEtPt to the desired value Briefly activate the MPI (NPN or PNP input logic) � For add. output operations the pulse counter or timer will be set to the SEtPt default value � For sub. output operations the pulse counter or timer will be set to the difference between the value of Preset 2 and the value of SEtPt . 8 Error message Err 1 Set value is outside the permitted range 6 or the optocoupler disabled when the preset value is reached. Setting the presets Setting via Decade Keys ogramming mode Preset 2 will always be ayed in the lower line. This is except for the ut operations AddBat, SubBat,AddTot and ot. Press the Prog/Mode key until the preset to be changed is displayed - or . Press any decade key � Display switches to the editor mode Set the desired preset value using the decade keys Press the Prog/Mode key to confirm the value and save it � Display switches to the editor mode of the next preset or Approx. 3 s after the last press of the decade keys or by pressing the Reset key the new preset value will be accepted and the counter will switch back to operating mode. 7.9.3 Setting the tracking presets (trail) If a tracking preset has been programmed, the value for Preset 2 can be set either via the decade keypad or via the Teach-IN function. However the value for Preset 1 must be entered via the decade keypad. In this instance, it is not possible to use the Teach-In function. 7.10 Set Function Both the pulse counter and the timer can be set to a default value by means of the Set function. Programme the MPI input to SEt Set menu item SEtPt to the desired value Briefly activate the MPI (NPN or PNP input logic) � For add. output operations the pulse counter or timer will be set to the SEtPt default value � For sub. output operations the pulse counter or timer will be set to the difference between the value of Preset 2 and the value of SEtPt . 8 Error message Err 1 Set value is outside the permitted range 16 ) 7.9 Setting the pr 7.9.1 Setting via Deca In programming mode Pres displayed in the lower line. output operations AddBat, S SubTot. Press the the prese displayed Press an � Display switches t Set the d using the Press the confirm t � Display switches t next preset Approx. 3 the deca the Rese value wil counter w operating Seite 16 ► Press any decade key� > Display switches to the editor mode� 7.9 Setting the pr 7.9.1 Setting via Deca In programming mode Pres displayed in the lower line. output operations AddBat, S SubTot. Press the the prese displayed Press an � Display switches t Set the d using the Press the confirm t � Display switches t next preset Approx. 3 the deca the Rese value wil counter w operating Seite 16 ► Set the desired preset value using the decade keys� 7.9.1 Setting via Deca In programming mode Pres displayed in the lower line. output operations AddBat, S SubTot. Press the the prese displayed Press an � Display switches t Set the d using the Press the confirm t � Display switches t next preset Approx. 3 the deca the Rese value wil counter w operating Seite 16 ► Press [P] to confirm the value and save it� > Display switches to the editor mode of the next preset� ( timed signal at Output 2, becomes passive with negative direction and when count < zero and subsequently with positive direction and when count > zero Duration of timed signal of Output 1, programmable from 00.01 to 99.99 s. Timed output is post-triggered. Active: Relay or optocoupler are activated when the preset value is reached. Passive: Relay becomes de-energized or the optocoupler disabled when the preset value is reached. Setting the presets Setting via Decade Keys ramming mode Preset 2 will always be ed in the lower line. This is except for the operations AddBat, SubBat,AddTot and t. Press the Prog/Mode key until the preset to be changed is displayed - or . Press any decade key Display switches to the editor mode Set the desired preset value using the decade keys Press the Prog/Mode key to confirm the value and save it Display switches to the editor mode of the next preset or Approx. 3 s after the last press of the decade keys or by pressing the Reset key the new preset value will be accepted and the counter will switch back to operating mode. 7.9.2 Setting with Teach-In Function Program the MPI input to tEAch In programming mode, select the preset to be changed using the Prog/Mode key Briefly activate the MPI (NPN or PNP input logic) � The current count value will be adopted as the new preset value The preset value can subsequently be further modified via the decade keypad. 7.9.3 Setting the tracking presets (trail) If a tracking preset has been programmed, the value for Preset 2 can be set either via the decade keypad or via the Teach-IN function. However the value for Preset 1 must be entered via the decade keypad. In this instance, it is not possible to use the Teach-In function. 7.10 Set Function Both the pulse counter and the timer can be set to a default value by means of the Set function. Programme the MPI input to SEt Set menu item SEtPt to the desired value Briefly activate the MPI (NPN or PNP input logic) � For add. output operations the pulse counter or timer will be set to the SEtPt default value � For sub. output operations the pulse counter or timer will be set to the difference between the value of Preset 2 and the value of SEtPt . 8 Error message Err 1 Set value is outside the permitted range 6 or timed signal at Output 2, becomes passive with negative direction and when count < zero and subsequently with positive direction and when count > zero Duration of timed signal of Output 1, programmable from 00.01 to 99.99 s. Timed output is post-triggered. Active: Relay or optocoupler are activated when the preset value is reached. Passive: Relay becomes de-energized or the optocoupler disabled when the preset value is reached. Setting the presets Setting via Decade Keys ogramming mode Preset 2 will always be ayed in the lower line. This is except for the ut operations AddBat, SubBat,AddTot and ot. Press the Prog/Mode key until the preset to be changed is displayed - or . Press any decade key � Display switches to the editor mode Set the desired preset value using the decade keys Press the Prog/Mode key to confirm the value and save it � Display switches to the editor mode of the next preset or Approx. 3 s after the last press of the decade keys or by pressing the Reset key the new preset value will be accepted and the counter will switch back to operating mode. 7.9.2 Setting with Teach-In Function Program the MPI input to tEAch In programming mode, select the preset to be changed using the Prog/Mode key Briefly activate the MPI (NPN or PNP input logic) � The current count value will be adopted as the new preset value The preset value can subsequently be further modified via the decade keypad. 7.9.3 Setting the tracking presets (trail) If a tracking preset has been programmed, the value for Preset 2 can be set either via the decade keypad or via the Teach-IN function. However the value for Preset 1 must be entered via the decade keypad. In this instance, it is not possible to use the Teach-In function. 7.10 Set Function Both the pulse counter and the timer can be set to a default value by means of the Set function. Programme the MPI input to SEt Set menu item SEtPt to the desired value Briefly activate the MPI (NPN or PNP input logic) � For add. output operations the pulse counter or timer will be set to the SEtPt default value � For sub. output operations the pulse counter or timer will be set to the difference between the value of Preset 2 and the value of SEtPt . 8 Error message Err 1 Set value is outside the permitted range 16 ) 7.9.1 Setting via Deca In programming mode Pres displayed in the lower line. output operations AddBat, S SubTot. Press the the prese displayed Press an � Display switches t Set the d using the Press the confirm t � Display switches t next preset Approx. 3 the deca the Rese value wil counter w operating Seite 16 > Approx� 3 s after the last press of the decade keys or by pressing [R] key the new preset value will be accepted and the counter will switch back to operating mode� p g g displayed in the lower line. output operations AddBat, S SubTot. Press the the prese displayed Press an � Display switches t Set the d using the Press the confirm t � Display switches t next preset Approx. 3 the deca the Rese value wil counter w operating Seite 16 7.8.2 Setting via Teach-in function ► Programme the MPI input to tEAch� Zählerstand < Null passiv und anschließend bei positiver Richtung und Zählerstand > Null passiv Dauer des Wischsignals von Ausgang 2, einstellbar von 00.01 bis 99.99 s. Wischsignal wird nachgetriggert. Aktiv: Relais bzw. Optokoppler werden bei Erreichen des Vorwahlwerts angesteuert. Passiv: Relais wird bei Erreichen des Vorwahlwert spannungslos bzw. der Optokoppler gesperrt. 7.9 Vorwahleinstellung 7.9.2 Einstellung mit T MPI-Eing programm Im Betrie Prog/Mod ändernde MPI-Eingang (NPN oder P kurzzeitig aktivieren � der aktuelle Zähle Vorwahlwert übern Der Vorwahlwert k weiter mit den Dek werden 7.9.3 Einstellung bei S ► Press [P] until the preset to be changed is displayed� ( Preset 2 and subsequently with negative direction and when count < Preset 2 SUB mode output operations: timed signal at Output 2, becomes passive with negative direction and when count < zero and subsequently with positive direction and when count > zero Duration of timed signal of Output 1, programmable from 00.01 to 99.99 s. Timed output is post-triggered. Active: Relay or optocoupler are activated when the preset value is reached. Passive: Relay becomes de-energized or the optocoupler disabled when the preset value is reached. Setting the presets Setting via Decade Keys ramming mode Preset 2 will always be ed in the lower line. This is except for the operations AddBat, SubBat,AddTot and t. Press the Prog/Mode key until the preset to be changed is displayed - or . Press any decade key Display switches to the editor mode Set the desired preset value using the decade keys Press the Prog/Mode key to confirm the value and save it Display switches to the editor mode of the next preset or Approx. 3 s after the last press of the decade keys or by pressing the Reset key the new preset 7.9.2 Setting with Teach-In Function Program the MPI input to tEAch In programming mode, select the preset to be changed using the Prog/Mode key Briefly activate the MPI (NPN or PNP input logic) � The current count value will be adopted as the new preset value The preset value can subsequently be further modified via the decade keypad. 7.9.3 Setting the tracking presets (trail) If a tracking preset has been programmed, the value for Preset 2 can be set either via the decade keypad or via the Teach-IN function. However the value for Preset 1 must be entered via the decade keypad. In this instance, it is not possible to use the Teach-In function. 7.10 Set Function Both the pulse counter and the timer can be set to a default value by means of the Set function. Programme the MPI input to SEt Set menu item SEtPt to the desired value Briefly activate the MPI (NPN or PNP input logic) � For add. output operations the pulse counter or timer will be set to the SEtPt default value � For sub. output operations the pulse counter or timer will be set to the difference between the value of Preset 2 and the value of SEtPt . 8 Error message Err 1 Set value is outside the permitted range or Preset 2 and subsequently with negative direction and when count < Preset 2 SUB mode output operations: timed signal at Output 2, becomes passive with negative direction and when count < zero and subsequently with positive direction and when count > zero Duration of timed signal of Output 1, programmable from 00.01 to 99.99 s. Timed output is post-triggered. Active: Relay or optocoupler are activated when the preset value is reached. Passive: Relay becomes de-energized or the optocoupler disabled when the preset value is reached. Setting the presets Setting via Decade Keys ogramming mode Preset 2 will always be ayed in the lower line. This is except for the ut operations AddBat, SubBat,AddTot and ot. Press the Prog/Mode key until the preset to be changed is displayed - or . Press any decade key � Display switches to the editor mode Set the desired preset value using the decade keys Press the Prog/Mode key to confirm the value and save it � Display switches to the editor mode of the next preset or Approx. 3 s after the last press of the decade keys or by pressing the Reset key the new preset 7.9.2 Setting with Teach-In Function Program the MPI input to tEAch In programming mode, select the preset to be changed using the Prog/Mode key Briefly activate the MPI (NPN or PNP input logic) � The current count value will be adopted as the new preset value The preset value can subsequently be further modified via the decade keypad. 7.9.3 Setting the tracking presets (trail) If a tracking preset has been programmed, the value for Preset 2 can be set either via the decade keypad or via the Teach-IN function. However the value for Preset 1 must be entered via the decade keypad. In this instance, it is not possible to use the Teach-In function. 7.10 Set Function Both the pulse counter and the timer can be set to a default value by means of the Set function. Programme the MPI input to SEt Set menu item SEtPt to the desired value Briefly activate the MPI (NPN or PNP input logic) � For add. output operations the pulse counter or timer will be set to the SEtPt default value � For sub. output operations the pulse counter or timer will be set to the difference between the value of Preset 2 and the value of SEtPt . 8 Error message Err 1 Set value is outside the permitted range ) ► Briefly activate the MPI (NPN or PNP input logic)� > The current count value will be adopted as the new preset value� Zählerstand < Null passiv und anschließend bei positiver Richtung und Zählerstand > Null passiv Dauer des Wischsignals von Ausgang 2, einstellbar von 00.01 bis 99.99 s. Wischsignal wird nachgetriggert. Aktiv: Relais bzw. Optokoppler werden bei Erreichen des Vorwahlwerts angesteuert. Passiv: Relais wird bei Erreichen des Vorwahlwert spannungslos bzw. der Optokoppler gesperrt. 7 9 V hl i t ll 7.9.2 Einstellung mit T MPI-Eing programm Im Betrie Prog/Mod ändernde MPI-Eingang (NPN oder P kurzzeitig aktivieren � der aktuelle Zähle Vorwahlwert übern Der Vorwahlwert k weiter mit den Dek werden 7.9.3 Einstellung bei S ► The preset value can subsequently be further modified via the decade keypad� SUB mod timed sig becomes direction and subs direction Duration Output 1 00.01 to Timed ou Active: Relay or activated is reache Passive: Relay be the optoc the prese 7.9 Setting the pr 7.9.1 Setting via Deca In programming mode Pres displayed in the lower line. output operations AddBat, S SubTot. Press the the prese displayed Press an � Display switches t Set the d using the Press the confirm t � Display switches t next preset

16 7.8.3 Setting the tracking presets (trail) If a tracking preset has been programmed, the value for Preset 2 can be set either via the decade keypad or via the Teach-In function� However the value for Preset 1 must be entered via the decade keypad� In this instance, it is not possible to use the Teach-In function�

17 7.9 Set Function Both the pulse counter and the timer can be set to a default value by means of the Set function� ► Programme the MPI input to SEt� Preset 2 angezeigt. Ausnahme sind die Ausgangsoperationen AddBat, SubBat,AddTot und SubTot. Prog/Mode-Taste betätigen bis die zu ändernde Vorwahl oder angezeigt wird. Beliebige Dekadentaste betätigen � Anzeige schaltet in den Editiermode Mit Dekadentasten gewünschten Vorwahlwert einstellen Prog/Mode-Taste betätigen um den Wert zu bestätigen und zu speichern � Anzeige schaltet in den Editiermode der nächsten Vorwahl oder Ca. 3 s nach dem letzten Betätigen der Dekadentasten oder durch Betätigen der Reset- Taste wird der neue Vorwahlwert übernommen und in den Betriebsmode zurück geschaltet. Dekadenschalter eingestellt Teach-Funktion ausgescha 7.10 Setz-Funktion Impulszähler und Zeitzähler Setzfunktion auf einen Wert MPI-Eing programm Menuepu gewünsc MPI-Eingang (NPN oder P kurzzeitig aktivieren � Impulszähler bzw. Ausgangsoperatio SEtPt voreingeste Ausgangsoperatio von Vorwahl 2 und 8 Fehlermeldung Err 1 Setzwert außerhalb Bereichs Seite 16 ► Set menu item SEtPt to the desired value� ► Briefly activate the MPI (NPN or PNP input logic)� > For add� output operations the pulse counter or timer will be set to the SEtPt default value� For sub� output operations the pulse counter or timer will be set to the difference between the value of Preset 2 and the value of SEtPt� Preset 2 angezeigt. Ausnahme sind die Ausgangsoperationen AddBat, SubBat,AddTot und SubTot. Prog/Mode-Taste betätigen bis die zu ändernde Vorwahl oder angezeigt wird. Beliebige Dekadentaste betätigen � Anzeige schaltet in den Editiermode Mit Dekadentasten gewünschten Vorwahlwert einstellen Prog/Mode-Taste betätigen um den Wert zu bestätigen und zu speichern � Anzeige schaltet in den Editiermode der nächsten Vorwahl oder Ca. 3 s nach dem letzten Betätigen der Dekadentasten oder durch Betätigen der Reset- Taste wird der neue Vorwahlwert übernommen und in den Betriebsmode zurück geschaltet. Dekadenschalter eingestellt Teach-Funktion ausgescha 7.10 Setz-Funktion Impulszähler und Zeitzähler Setzfunktion auf einen Wert MPI-Eing programm Menuepu gewünsc MPI-Eingang (NPN oder P kurzzeitig aktivieren � Impulszähler bzw. Ausgangsoperatio SEtPt voreingeste Ausgangsoperatio von Vorwahl 2 und 8 Fehlermeldung Err 1 Setzwert außerhalb Bereichs Seite 16

18 8 Parameters 8.1 Default parameters Three default parameter sets have been permanently stored; these can be adapted as required� With each acknowledgment of the parameter sets, all parameters will be reset to the values listed in the table� The default parameter set P�USEr can be freely programmed� acknowledgment of the parameter sets, all parameters will be reset to the values listed in the table. The dEFAuL P.USEr can be freely programmed. Menu Parameter Sets Default setting Parameter set 1 Default setting Parameter set 2 Default setting Parameter set 3 Freely programmable User settings Factory settings are highlighted in grey rESmd Man.EL Man PrES 1 on on Pr.Out 1 t.Out 1 00.1 Pr.Out 2 t.Out 2 00.1 7.8.3 Setting the Basic Basic funct Programmi Pulse coun Programmi Timer/Hour Programmi Tacho/Freq freely programmed. Menu Parameter Sets Default setting Parameter set 1 Default setting Parameter set 2 Default setting Parameter set 3 Freely programmable User settings Factory settings are highlighted in grey t.Out 1 Pr.Out 2 t.Out 2 7.8.3 Setti Default setting Parameter set 1 Default setting Parameter set 2 Default setting Parameter set 3 Freely programmable User settings Factory settings are highlighted in grey Parameter set 1 Default setting Parameter set 2 Default setting Parameter set 3 Freely programmable User settings Factory settings are in grey 8.2 Table: Default Parameter Sets Display Description P.SEt 1 P.SEt 2 P.SET 3 P.USEr Func Basic function of the device Count Count Count Freely programmable User settings InP.PoL Input polarity PnP PnP PnP FiLtEr Filter for the signal inputs InpA and InpB on oFF oFF Count Count input mode Cnt�dir uP�dn Quad MPi User input LAtch LAtch Set Loc.InP Lock input ProG ProG ProG ModE Mode Add Sub TrAiL FActor Multiplication factor 01�0000 01�0000 01�0000 diViSo Division factor 01�0000 01�0000 01�0000 dP Decimal point 0 0 0�00 SEtPt Set value 000000 000000 0000�00 CoLor Display colour red�Grn red�Grn red�Grn rESmd Reset mode Man�EL Man�EL Man�EL PrES 1 Preset 1 on on on Pr.Out 1 Preset output 1 Pressing the Prog/Mode key acknowledges this prompt and terminates the programming; the modified settings are saved in the EEPROM. � The text SAVE is displayed for 2 s 7.8 Programming Menu 7.8.1 Default parameters Note: Three default parameter sets have been permanently stored; these can be adapted as required. With each acknowledgment of the parameter sets, all parameters will be reset to the values listed in the table. The dEFAuL P.USEr can be freely programmed. Menu Parameter Sets Default setting Parameter set 1 Default setting Parameter set 2 Default setting Parameter set 3 Freely programmable User settings F i hi hli h d 7.8.2 Table: Parameter Sets P.SEt 1 P.SEt 2 P.SET 3 Func Count Count Count InP.PoL PnP PnP PnP FiLtEr on oFF oFF Count Cnt.dir uP.dn Quad MPi LAtch LAtch Set Loc.InP ProG ProG ProG ModE Add Sub TrAiL FActor 01.0000 01.0000 01.0000 diViSo 01.0000 01.0000 01.0000 dP 0 0 0.00 SEtPt 000000 000000 0000.00 CoLor red.Grn red.Grn red.Grn rESmd Man.EL Man.EL Man.EL PrES 1 on on on Pr.Out 1 t.Out 1 00.10 Pr.Out 2 t.Out 2 00.10 00.10 7.8.3 Setting the Basic Function Basic function menu Programming menu Pulse counter (7.8.4) Programming menu Timer/Hour meter (7.8.6) Programming menu Tacho/Frequency meter (7.8.5) english Pressing the Prog/Mode key acknowledges this prompt and terminates the programming; the modified settings are saved in the EEPROM. � The text SAVE is displayed for 2 s 7.8 Programming Menu 7.8.1 Default parameters Note: Three default parameter sets have been permanently stored; these can be adapted as required. With each acknowledgment of the parameter sets, all parameters will be reset to the values listed in the table. The dEFAuL P.USEr can be freely programmed. Menu Parameter Sets Default setting Parameter set 1 Default setting Parameter set 2 Default setting Parameter set 3 Freely programmable User settings Factory settings are highlighted in grey 7.8.2 Table: Parameter Sets P.SEt 1 P.SEt 2 P.SET 3 Func Count Count Count InP.PoL PnP PnP PnP FiLtEr on oFF oFF Count Cnt.dir uP.dn Quad MPi LAtch LAtch Set Loc.InP ProG ProG ProG ModE Add Sub TrAiL FActor 01.0000 01.0000 01.0000 diViSo 01.0000 01.0000 01.0000 dP 0 0 0.00 SEtPt 000000 000000 0000.00 CoLor red.Grn red.Grn red.Grn rESmd Man.EL Man.EL Man.EL PrES 1 on on on Pr.Out 1 t.Out 1 00.10 Pr.Out 2 t.Out 2 00.10 00.10 7.8.3 Setting the Basic Function Basic function menu Programming menu Pulse counter (7.8.4) Programming menu Timer/Hour meter (7.8.6) Programming menu Tacho/Frequency meter (7.8.5) english Pressing the Prog/Mode key acknowledges this prompt and terminates the programming; the modified settings are saved in the EEPROM. � The text SAVE is displayed for 2 s 7.8 Programming Menu 7.8.1 Default parameters Note: Three default parameter sets have been permanently stored; these can be adapted as required. With each acknowledgment of the parameter sets, all parameters will be reset to the values listed in the table. The dEFAuL P.USEr can be freely programmed. Menu Parameter Sets Default setting Parameter set 1 Default setting Parameter set 2 Default setting Parameter set 3 Freely programmable User settings F i hi hli h d 7.8.2 Table: Parameter Sets P.SEt 1 P.SEt 2 P.SET 3 Func Count Count Count InP.PoL PnP PnP PnP FiLtEr on oFF oFF Count Cnt.dir uP.dn Quad MPi LAtch LAtch Set Loc.InP ProG ProG ProG ModE Add Sub TrAiL FActor 01.0000 01.0000 01.0000 diViSo 01.0000 01.0000 01.0000 dP 0 0 0.00 SEtPt 000000 000000 0000.00 CoLor red.Grn red.Grn red.Grn rESmd Man.EL Man.EL Man.EL PrES 1 on on on Pr.Out 1 t.Out 1 00.10 Pr.Out 2 t.Out 2 00.10 00.10 7.8.3 Setting the Basic Function Basic function menu Programming menu Pulse counter (7.8.4) Programming menu Timer/Hour meter (7.8.6) Programming menu Tacho/Frequency meter (7.8.5) english t.Out 1 Duration of timed signal of output 1 - 00�10 - Pr.Out 2 Preset output 2 Pressing the Prog/Mode key acknowledges this prompt and terminates the programming; the modified settings are saved in the EEPROM. � The text SAVE is displayed for 2 s 7.8 Programming Menu 7.8.1 Default parameters Note: Three default parameter sets have been permanently stored; these can be adapted as required. With each acknowledgment of the parameter sets, all parameters will be reset to the values listed in the table. The dEFAuL P.USEr can be freely programmed. Menu Parameter Sets Default setting Parameter set 1 Default setting Parameter set 2 Default setting Parameter set 3 Freely programmable User settings 7.8.2 Table: Parameter Sets P.SEt 1 P.SEt 2 P.SET 3 Func Count Count Count InP.PoL PnP PnP PnP FiLtEr on oFF oFF Count Cnt.dir uP.dn Quad MPi LAtch LAtch Set Loc.InP ProG ProG ProG ModE Add Sub TrAiL FActor 01.0000 01.0000 01.0000 diViSo 01.0000 01.0000 01.0000 dP 0 0 0.00 SEtPt 000000 000000 0000.00 CoLor red.Grn red.Grn red.Grn rESmd Man.EL Man.EL Man.EL PrES 1 on on on Pr.Out 1 t.Out 1 00.10 Pr.Out 2 t.Out 2 00.10 00.10 7.8.3 Setting the Basic Function Basic function menu Programming menu Pulse counter (7.8.4) Programming menu Timer/Hour meter (7.8.6) Programming menu english Pressing the Prog/Mode key acknowledges this prompt and terminates the programming; the modified settings are saved in the EEPROM. � The text SAVE is displayed for 2 s 7.8 Programming Menu 7.8.1 Default parameters Note: Three default parameter sets have been permanently stored; these can be adapted as required. With each acknowledgment of the parameter sets, all parameters will be reset to the values listed in the table. The dEFAuL P.USEr can be freely programmed. Menu Parameter Sets Default setting Parameter set 1 Default setting Parameter set 2 Default setting Parameter set 3 Freely programmable User settings 7.8.2 Table: Parameter Sets P.SEt 1 P.SEt 2 P.SET 3 Func Count Count Count InP.PoL PnP PnP PnP FiLtEr on oFF oFF Count Cnt.dir uP.dn Quad MPi LAtch LAtch Set Loc.InP ProG ProG ProG ModE Add Sub TrAiL FActor 01.0000 01.0000 01.0000 diViSo 01.0000 01.0000 01.0000 dP 0 0 0.00 SEtPt 000000 000000 0000.00 CoLor red.Grn red.Grn red.Grn rESmd Man.EL Man.EL Man.EL PrES 1 on on on Pr.Out 1 t.Out 1 00.10 Pr.Out 2 t.Out 2 00.10 00.10 7.8.3 Setting the Basic Function Basic function menu Programming menu Pulse counter (7.8.4) Programming menu Timer/Hour meter (7.8.6) Programming menu Tacho/Frequency meter (7.8.5) english Pressing the Prog/Mode key acknowledges this prompt and terminates the programming; the modified settings are saved in the EEPROM. � The text SAVE is displayed for 2 s 7.8 Programming Menu 7.8.1 Default parameters Note: Three default parameter sets have been permanently stored; these can be adapted as required. With each acknowledgment of the parameter sets, all parameters will be reset to the values listed in the table. The dEFAuL P.USEr can be freely programmed. Menu Parameter Sets Default setting Parameter set 1 Default setting Parameter set 2 Default setting Parameter set 3 Freely programmable User settings 7.8.2 Table: Parameter Sets P.SEt 1 P.SEt 2 P.SET 3 Func Count Count Count InP.PoL PnP PnP PnP FiLtEr on oFF oFF Count Cnt.dir uP.dn Quad MPi LAtch LAtch Set Loc.InP ProG ProG ProG ModE Add Sub TrAiL FActor 01.0000 01.0000 01.0000 diViSo 01.0000 01.0000 01.0000 dP 0 0 0.00 SEtPt 000000 000000 0000.00 CoLor red.Grn red.Grn red.Grn rESmd Man.EL Man.EL Man.EL PrES 1 on on on Pr.Out 1 t.Out 1 00.10 Pr.Out 2 t.Out 2 00.10 00.10 7.8.3 Setting the Basic Function Basic function menu Programming menu Pulse counter (7.8.4) Programming menu Timer/Hour meter (7.8.6) Programming menu Tacho/Frequency meter (7.8.5) english t.Out 2 Duration of timed signal of output 1 - 00�10 00�10 factory settings are highlighted in grey Complete parameter structure and menues see attachement�

19 8.3 Setting the basic function of the device hted Pr.Out 2 t.Out 2 00.10 00.10 7.8.3 Setting the Basic Function Basic function menu Programming menu Pulse counter (7.8.4) Programming menu Timer/Hour meter (7.8.6) Programming menu Tacho/Frequency meter (7.8.5) Seite 7 ing set 1 ing set 2 ing set 3 rammable gs tings are highlighted 7.8.3 Setting the Basic Function Basic function menu Programming menu Pulse counter (7.8.4) Programming menu Timer/Hour meter (7.8.6) Programming menu Tacho/Frequency meter (7.8.5) Seite 7 Default setting Parameter set 2 Default setting Parameter set 3 Freely programmable User settings Factory settings are highlighted in grey Programming menu Pulse counter (7.8.4) Programming menu Timer/Hour meter (7.8.6) Programming menu Tacho/Frequency meter (7.8.5) Seite 7 Default setting Parameter set 3 Freely programmable User settings Factory settings are highlighted in grey Programming menu Timer/Hour meter (7. Programming menu Tacho/Frequency me Parameters and submenues of the basic functions ● Pulse counter (→ 8.4) ● Timer/Hour meter (→ 8.5) ● Tacho/Frequency meter (→ 8.6)

20 8.4 Pulse counter 8.4.1 Input Submenues for the signal and control inputs� Display Description Submenu Value InP.PoL Input polarity PnP PNP: switching to Plus for all inputs in common nPn NPN: switching to 0 V for all inputs in common FiLtEr Filter for the signal inputs InpA and InpB oFF Maximum count frequency on Damped to approx� 30 Hz (for control with mechanical contacts) Count Count input mode Cnt.Dir Count/Direction INP A: count input INP B: count direction input uP.dn Differential counting [A-B] INP A: count input add INP B: count input sub uP.uP Totalising [A+B] INP A: count input add INP B: count input add quAd Quadrature input INP A: count input 0° INP B: count input 90° quA2 Quadrature with pulse doubling INP A: count input 0° INP B: count input 90° Each pulse edge of INP A will be counted quA4 Quadrature x4 INP A: count input 0° INP B: count input 90° Each pulse edge of INP A and INP B will be counted� A / B Ratio measurement [A/B] Inp A: count input A Inp B: count input B A % b Percentage differential counting [(A-B) / A in %] Inp A: count input A Inp B: count input B

21 Display Description Submenu Value MPi User input LAtch When the MPI input is activated the display is “frozen” and remains “frozen” until the MPI input is deactivated� Internally the preset counter continues counting� tEAch When the MPI input is activated the current count value for the preset that has just been selected will be adopted as the new preset value� SEt When the MPI input is activated the preset counter will be set to the value specified in the parameter SEtPt� Loc.InP Lock input ProG When the lock input is activated the programming is inhibited� PrESET When the lock input is activated the setting of the preset values is inhibited� PrG.PrE When the lock input is activated the setting of the preset values and the programming are both inhibited� factory settings are highlighted in grey 8.4.2 Mode Submenues for output operations� Display Description Submenu Value ModE Submenu for determining the operation of the outputs Add Count mode ADD Outputs active when count status ≥ preset value Reset to zero� Sub Count mode SUBTRACT Output 1 active when count status ≤ preset value 1. Output 2 active when count status ≤ 0. Reset to preset 2 AddAr Count mode ADDING with automatic reset Output 1 active when count status ≥ preset value 1. Output 2 (timed signal) active when count status = preset value 2� Automatic reset to zero when count status = preset value 2� Reset to zero� SubAr Count mode SUBTRACTING with automatic reset Output 1 active when count status ≤ preset value 1. Output 2 (timed signal) active when count status = 0� Automatic reset to preset 2 when count status = 0� Reset to preset 2�

22 Display Description Submenu Value AddbAt Count mode ADDING with automatic reset and Batch counter Output 2 (timed signal) active when main counter = preset value 2� Automatic reset to zero when main counter = preset 2� Batch counter counts the number of automatic repetitions of preset 2� Output 1 active when Batch counter ≥ preset 1. Manual reset sets both counters to zero� Electrical reset only sets the main counter to zero� SubbAt Count mode SUBTRACTING with automatic reset and Batch counter Output 2 (timed signal) active when main counter = zero� Automatic reset to preset 2 when main counter = zero� Batch counter counts the number of automatic repetitions of preset 2� Output 1 active when Batch counter ≥ preset 1. Manual reset sets main counter to preset value 2, batch counter to zero� Electrical reset only sets the main counter to preset value 2� Addtot Count mode ADDING with automatic reset and Total counter Output 2 (timed signal) active when main counter = preset value 2� Automatic reset to zero when main counter = preset value 2� Total counter counts all the count pulses from the main counter� Output 1 active when total counter ≥ preset value 1. Manual reset sets both counters to zero� Electrical reset only sets the main counter to zero� Subtot Count mode SUBTRACTING with automatic reset and Total counter Output 2 (timed signal) active when main counter = zero� Automatic reset to preset value 2 when main counter = zero� Total counter counts (sub from preset value 1) all count pulses from main counter� Output 1 active when Total counter ≤ zero. Manual reset sets both counters to the preset values� Electrical reset sets only main counter to preset value 2� trAiL Tracking Preset mode When preset 2 is changed then preset 1 automatically tracks it� Reset to zero� Preset 1 relative to preset 2� tr_Ar Tracking Preset mode with automatic reset When preset 2 is changed then preset 1 automatically tracks it� Reset to zero� Automatic reset to zero when main counter = preset value� factory settings are highlighted in grey

23 8.4.3 Config Submenues for matching the input pulses and display� Display Description Submenu Value FActor Multiplication factor 01.0000 Factory setting 00.0001... 99.9999 Multiplication factor can be programmed from 00�0001 to 99�9999� The setting 00�0000 will not beaccepted� diViSo Division factor 01.0000 Factory setting 01.0000... 99.9999 Division factor can be programmed from 01�0000 to 99�9999� The setting < 01�0000 will not be accepted� dp Decimal point setting (only optical function) 0 no decimal place 0.0 1 decimal place 0.00 2 decimal places 0.000 3 decimal places 0.0000 4 decimal places 0.00000 5 decimal places SetPt Set value 000000 Factory setting 000000... 999999 Set value can be programmed from 000000 to 999999� A previously programmed decimal point will be displayed� CoLor Display colour (not supported) rEd Upper line red� Lower line red� rEdGrn Upper line red Lower line green factory settings are highlighted in grey

24 8.4.4 Reset mode Submenues for reset mode� Display Description Submenu Value rESmd Setting the reset mode Man.EL Manual reset (with red key) and electrical reset (reset input)� no rES No reset possible (red key and reset input inhibited)� EL.rEs Only electrical reset possible (reset input)� MAnrE Only manual reset possible (red key)� factory settings are highlighted in grey 8.4.5 Preset 1 Submenues for preset 1� Display Description Submenu Value PrES 1 Submenu for turning preset 1 ON/OFF on Preset 1 ON off Preset 1 OFF and no function Pr.Out 1 Preset output 1 eset mode When preset 2 is changed then preset 1 automatically tracks it. Reset to zero Preset 1 relative to preset 2 (see also section 17. Output operations) Tracking Preset mode with automatic reset When preset 2 is changed then preset 1 automatically tracks it. Reset to zero. Automatic reset to zero when main counter = preset value 2. Preset 1 relative to Preset 2 (see also section 17. Output operations) Submenu for configuration Submenu for matching the time ranges and display Unit of time Unit of time: seconds Decimal point setting determines the resolution Unit of time: minutes Decimal point setting determines the resolution Unit of time: hours Decimal point setting determines the resolution Unit of time: Hrs. Min. Sec. nt setting (Resolution) Decimal place (determines the resolution) 0 no decimal place 0.0 1 decimal place 0.00 2 decimal places 0.000 3 decimal places Set value can be programmed from 000000 to 999999 A previously programmed decimal point will be displayed Display colour (for 6.92x.x1x3.xx0] Display colour upper line red lower line red Display colour upper line red lower line green 7.8.6.4 Submenu for reset mode Setting the reset mode Manual reset (with red key) and electrical reset (reset input) No reset possible (red key and reset input inhibited) Only electrical reset possible (reset input) Only manual reset possible (red key) 7.8.6.5 Submenu for Preset 1 Submenu for turning preset 1 ON/OFF Preset 1 ON Preset 1 OFF and no function ADD mode output operations: permanent signal at Output 1, becomes active when count > Preset 1 SUB mode output operations: permanent signal at Output 1, becomes active when count < Preset 1 ADD mode output operations: permanent signal at Output 1, becomes passive when count > Preset 1 ADD mode output operations: permanent signal at Output 1, becomes active when count ≥ Preset 1 SUB mode output operations: permanent signal at Output 1, becomes active when count ≤ Preset 1 eset mode When preset 2 is changed then preset 1 automatically tracks it. Reset to zero Preset 1 relative to preset 2 (see also section 17. Output operations) Tracking Preset mode with automatic reset When preset 2 is changed then preset 1 automatically tracks it. Reset to zero. Automatic reset to zero when main counter = preset value 2. Preset 1 relative to Preset 2 (see also section 17. Output operations) Submenu for configuration Submenu for matching the time ranges and display Unit of time Unit of time: seconds Decimal point setting determines the resolution Unit of time: minutes Decimal point setting determines the resolution Unit of time: hours Decimal point setting determines the resolution Unit of time: Hrs. Min. Sec. nt setting (Resolution) Decimal place (determines the resolution) 0 no decimal place 0.0 1 decimal place 0.00 2 decimal places 0.000 3 decimal places Set value can be programmed from 000000 to 999999 A previously programmed decimal point will be displayed Display colour (for 6.92x.x1x3.xx0] Display colour upper line red lower line red Display colour upper line red lower line green 7.8.6.4 Submenu for reset mode Setting the reset mode Manual reset (with red key) and electrical reset (reset input) No reset possible (red key and reset input inhibited) Only electrical reset possible (reset input) Only manual reset possible (red key) 7.8.6.5 Submenu for Preset 1 Submenu for turning preset 1 ON/OFF Preset 1 ON Preset 1 OFF and no function ADD mode output operations: permanent signal at Output 1, becomes active when count > Preset 1 SUB mode output operations: permanent signal at Output 1, becomes active when count < Preset 1 ADD mode output operations: permanent signal at Output 1, becomes passive when count > Preset 1 ADD mode output operations: permanent signal at Output 1, becomes passive when count ≥ Preset 1 SUB mode output operations: permanent signal at Output 1, becomes passive when count ≤ Preset 1 SUB mode output operations: permanent signal at Output 1, becomes passive when count < Preset 1 ADD mode output operations: timed signal at Output 1, becomes active when count > Preset 1. (Activation only in positive direction) SUB mode output operations: timed output at Output 1, becomes active when count < Preset 1 (Activation only in negative direction) ADD mode output operations: timed signal at Output 1, becomes passive when count > Preset 1. (Deactivation only in positive direction) SUB mode output operations: timed output at Output 1, becomes passive when count < Preset 1. (Deactivation only in negative direction). ADD mode output operations: timed signal at Output1, becomes active with positive direction and when count > Preset 1 and subsequently active with negative direction and when count < Preset 1 SUB mode output operations: timed signal at Output 1, becomes active with negative direction and when count < 7.8.6.6 Submenu for Preset 2 Submenu for Preset 2 ADD mode output operations: permanent signal at Output 2, becomes active when count > Preset 2 SUB mode output operations: permanent signal at Output 2, becomes active when count < zero ADD mode output operations: permanent signal at Output 2, becomes passive when count > Preset 2 SUB mode output operations: permanent signal at Output 2, becomes passive when count < zero ADD mode output operations: timed signal at Output 2, becomes active when count > Preset 2 (Activation only in positive direction). SUB mode output operations: permanent signal at Output 2, becomes active when count < zero (Activation only in negative direction) ADD mode output operations: timed signal at Output 2, becomes passive when count > P t 2 (D ti ti l i english ADD mode output operations: timed signal at Output 1, becomes active when count ≥ Preset 1. (Activation only in positive direction) SUB mode output operations: timed output at Output 1, becomes active when count ≤ Preset 1 (Activation only in negative direction) SUB mode output operations: permanent signal at Output 1, becomes passive when count < Preset 1 ADD mode output operations: timed signal at Output 1, becomes active when count > Preset 1. (Activation only in positive direction) SUB mode output operations: timed output at Output 1, becomes active when count < Preset 1 (Activation only in negative direction) ADD mode output operations: timed signal at Output 1, becomes passive when count > Preset 1. (Deactivation only in positive direction) SUB mode output operations: timed output at Output 1, becomes passive when count < Preset 1. (Deactivation only in negative direction). ADD mode output operations: timed signal at Output1, becomes active with positive direction and when count > Preset 1 and subsequently active with negative direction and when count < Preset 1 SUB mode output operations: timed signal at Output 1, becomes active with negative direction and when count < 7.8.6.6 Submenu for Preset 2 Submenu for Preset 2 ADD mode output operations: permanent signal at Output 2, becomes active when count > Preset 2 SUB mode output operations: permanent signal at Output 2, becomes active when count < zero ADD mode output operations: permanent signal at Output 2, becomes passive when count > Preset 2 SUB mode output operations: permanent signal at Output 2, becomes passive when count < zero ADD mode output operations: timed signal at Output 2, becomes active when count > Preset 2 (Activation only in positive direction). SUB mode output operations: permanent signal at Output 2, becomes active when count < zero (Activation only in negative direction) ADD mode output operations: timed signal at Output 2, becomes passive when count > P t 2 (D ti ti l i english ADD mode output operations: timed signal at Output 1, becomes passive when count ≥ Preset 1. (Deactivation only in positive direction) SUB mode output operations: timed output at Output 1, becomes passive when count ≤ Preset 1. (Deactivation only in negative direction)

25 Display Description Submenu Value g ) ADD mode output operations: timed signal at Output 1, becomes passive when count > Preset 1. (Deactivation only in positive direction) SUB mode output operations: timed output at Output 1, becomes passive when count < Preset 1. (Deactivation only in negative direction). ADD mode output operations: timed signal at Output1, becomes active with positive direction and when count > Preset 1 and subsequently active with negative direction and when count < Preset 1 SUB mode output operations: timed signal at Output 1, becomes active with negative direction and when count < Preset 1 and subsequently active with positive direction and when count > Preset 1 ADD mode output operations: timed signal at Output1, becomes passive with positive direction and when count > Preset 1 and subsequently passive with negative direction and when count < Preset 1 SUB mode output operations: timed output at Output 1, becomes passive with negative direction and when count < Preset 1 and subsequently passive with positive direction and when count > Preset 1 Duration of timed signal of Output 1, programmable from 00.01 to 99.99 s. Timed signal is post-triggered ADD mode output operations: permanent signal at Output 2, becomes passive when count > Preset 2 SUB mode output operations: permanent signal at Output 2, becomes passive when count < zero ADD mode output operations: timed signal at Output 2, becomes active when count > Preset 2 (Activation only in positive direction). SUB mode output operations: permanent signal at Output 2, becomes active when count < zero (Activation only in negative direction) ADD mode output operations: timed signal at Output 2, becomes passive when count > Preset 2 (Deactivation only in positive direction) SUB mode output operations: permanent signal at Output 2, becomes passive when count < zero (Deactivation only in negative direction). ADD mode output operations: timed signal at Output 2, becomes active with positive direction and when count > Preset 2 and subsequently with negative direction and when count < Preset 2 SUB mode output operations: timed signal at Output 2, becomes active with negative direction and when count < zero and subsequently with positive direction and when count > zero ADD mode output operations: timed signal at Output 2, becomes passive with positive direction and when count > english Seite 15 ADD mode output operations: timed signal at Output1, becomes active with positive direction and when count ≥ Preset 1 and subsequently active with negative direction and when count ≤ Preset 1 SUB mode output operations: timed signal at Output 1, becomes active with negative direction and when count ≤ Preset 1 and subsequently active with positive direction and when count ≥ Preset 1 ADD mode output operations: timed signal at Output 1, becomes passive when count > Preset 1. (Deactivation only in positive direction) SUB mode output operations: timed output at Output 1, becomes passive when count < Preset 1. (Deactivation only in negative direction). ADD mode output operations: timed signal at Output1, becomes active with positive direction and when count > Preset 1 and subsequently active with negative direction and when count < Preset 1 SUB mode output operations: timed signal at Output 1, becomes active with negative direction and when count < Preset 1 and subsequently active with positive direction and when count > Preset 1 ADD mode output operations: timed signal at Output1, becomes passive with positive direction and when count > Preset 1 and subsequently passive with negative direction and when count < Preset 1 SUB mode output operations: timed output at Output 1, becomes passive with negative direction and when count < Preset 1 and subsequently passive with positive direction and when count > Preset 1 Duration of timed signal of Output 1, programmable from 00.01 to 99.99 s. Timed signal is post-triggered permanent signal at Output 2, becomes passive when count > Preset 2 SUB mode output operations: permanent signal at Output 2, becomes passive when count < zero ADD mode output operations: timed signal at Output 2, becomes active when count > Preset 2 (Activation only in positive direction). SUB mode output operations: permanent signal at Output 2, becomes active when count < zero (Activation only in negative direction) ADD mode output operations: timed signal at Output 2, becomes passive when count > Preset 2 (Deactivation only in positive direction) SUB mode output operations: permanent signal at Output 2, becomes passive when count < zero (Deactivation only in negative direction). ADD mode output operations: timed signal at Output 2, becomes active with positive direction and when count > Preset 2 and subsequently with negative direction and when count < Preset 2 SUB mode output operations: timed signal at Output 2, becomes active with negative direction and when count < zero and subsequently with positive direction and when count > zero ADD mode output operations: timed signal at Output 2, becomes passive with positive direction and when count > english Seite 15 ADD mode output operations: timed signal at Output1, becomes passive with positive direction and when count ≥ Preset 1 and subsequently passive with negative direction and when count ≤ Preset 1 SUB mode output operations: timed output at Output 1, becomes passive with negative direction and when count ≤ Preset 1 and subsequently passive with positive direction and when count ≥ Preset 1 t.Out 1 Duration of timed signal of Output 1 Timed signal is post-triggered 00.01 Factory setting 00.01... 99.99 Programmable from 00�01 to 99�99 s factory settings are highlighted in grey 8.4.6 Preset 2 Submenues for preset 2� Display Description Submenu Value PrES 2 Submenu for Preset 2 Pr.Out 2 Preset output 2 eset mode When preset 2 is changed then preset 1 automatically tracks it. Reset to zero Preset 1 relative to preset 2 (see also section 17. Output operations) Tracking Preset mode with automatic reset When preset 2 is changed then preset 1 automatically tracks it. Reset to zero. Automatic reset to zero when main counter = preset value 2. Preset 1 relative to Preset 2 (see also section 17. Output operations) Submenu for configuration Submenu for matching the time ranges and display Unit of time Unit of time: seconds Decimal point setting determines the resolution Unit of time: minutes Decimal point setting determines the resolution Unit of time: hours Decimal point setting determines the resolution Unit of time: Hrs. Min. Sec. nt setting (Resolution) Decimal place (determines the resolution) 0 no decimal place 0.0 1 decimal place 0.00 2 decimal places 0.000 3 decimal places Set value can be programmed from 000000 to 999999 A previously programmed decimal point will be displayed Display colour (for 6.92x.x1x3.xx0] Display colour upper line red lower line red Display colour upper line red lower line green 7.8.6.4 Submenu for reset mode Setting the reset mode Manual reset (with red key) and electrical reset (reset input) No reset possible (red key and reset input inhibited) Only electrical reset possible (reset input) Only manual reset possible (red key) 7.8.6.5 Submenu for Preset 1 Submenu for turning preset 1 ON/OFF Preset 1 ON Preset 1 OFF and no function ADD mode output operations: permanent signal at Output 1, becomes active when count > Preset 1 SUB mode output operations: permanent signal at Output 1, becomes active when count < Preset 1 ADD mode output operations: permanent signal at Output 1, becomes passive when count > Preset 1 ADD mode output operations: permanent signal at Output 2, becomes active when count ≥ Preset 2 SUB mode output operations: permanent signal at Output 2, becomes active when count ≤ zero eset mode When preset 2 is changed then preset 1 automatically tracks it. Reset to zero Preset 1 relative to preset 2 (see also section 17. Output operations) Tracking Preset mode with automatic reset When preset 2 is changed then preset 1 automatically tracks it. Reset to zero. Automatic reset to zero when main counter = preset value 2. Preset 1 relative to Preset 2 (see also section 17. Output operations) Submenu for configuration Submenu for matching the time ranges and display Unit of time Unit of time: seconds Decimal point setting determines the resolution Unit of time: minutes Decimal point setting determines the resolution Unit of time: hours Decimal point setting determines the resolution Unit of time: Hrs. Min. Sec. nt setting (Resolution) Decimal place (determines the resolution) 0 no decimal place 0.0 1 decimal place 0.00 2 decimal places 0.000 3 decimal places Set value can be programmed from 000000 to 999999 A previously programmed decimal point will be displayed Display colour (for 6.92x.x1x3.xx0] Display colour upper line red lower line red Display colour upper line red lower line green 7.8.6.4 Submenu for reset mode Setting the reset mode Manual reset (with red key) and electrical reset (reset input) No reset possible (red key and reset input inhibited) Only electrical reset possible (reset input) Only manual reset possible (red key) 7.8.6.5 Submenu for Preset 1 Submenu for turning preset 1 ON/OFF Preset 1 ON Preset 1 OFF and no function ADD mode output operations: permanent signal at Output 1, becomes active when count > Preset 1 SUB mode output operations: permanent signal at Output 1, becomes active when count < Preset 1 ADD mode output operations: permanent signal at Output 1, becomes passive when count > Preset 1 ADD mode output operations: permanent signal at Output 2, becomes passive when count ≥ Preset 2 SUB mode output operations: permanent signal at Output 2, becomes passive when count ≤ zero SUB mode output operations: permanent signal at Output 1, becomes passive when count < Preset 1 ADD mode output operations: timed signal at Output 1, becomes active when count > Preset 1. (Activation only in positive direction) SUB mode output operations: timed output at Output 1, becomes active when count < Preset 1 (Activation only in negative direction) ADD mode output operations: timed signal at Output 1, becomes passive when count > Preset 1. (Deactivation only in positive direction) SUB mode output operations: timed output at Output 1 7.8.6.6 Submenu for Preset 2 Submenu for Preset 2 ADD mode output operations: permanent signal at Output 2, becomes active when count > Preset 2 SUB mode output operations: permanent signal at Output 2, becomes active when count < zero ADD mode output operations: permanent signal at Output 2, becomes passive when count > Preset 2 SUB mode output operations: permanent signal at Output 2, becomes passive when count < zero english ADD mode output operations: timed signal at Output 2, becomes active when count ≥ Preset 2 (Activation only in positive direction)� SUB mode output operations: permanent signal at Output 2, becomes active when count ≤ zero (Activation only in negative direction)

26 Display Description Submenu Value Preset 1 ADD mode output operations: timed signal at Output 1, becomes active when count > Preset 1. (Activation only in positive direction) SUB mode output operations: timed output at Output 1, becomes active when count < Preset 1 (Activation only in negative direction) ADD mode output operations: timed signal at Output 1, becomes passive when count > Preset 1. (Deactivation only in positive direction) SUB mode output operations: timed output at Output 1, becomes passive when count < Preset 1. (Deactivation only in negative direction). ADD mode output operations: timed signal at Output1, becomes active with positive direction and when count > Preset 1 and subsequently active with negative direction and when count < Preset 1 SUB mode output operations: timed signal at Output 1, becomes active with negative direction and when count < Preset 1 and subsequently active with positive direction and when count > Preset 1 ADD mode output operations: timed signal at Output1, becomes passive with positive direction and when count > Preset 1 and subsequently passive with negative direction and when count < Preset 1 SUB mode output operations: timed output at Output 1, becomes passive with negative direction and when count < Preset 1 and subsequently passive with positive direction and when count > Preset 1 Duration of timed signal of Output 1, programmable from 00.01 to 99.99 s. Timed signal is post-triggered ADD mode output operations: permanent signal at Output 2, becomes active when count > Preset 2 SUB mode output operations: permanent signal at Output 2, becomes active when count < zero ADD mode output operations: permanent signal at Output 2, becomes passive when count > Preset 2 SUB mode output operations: permanent signal at Output 2, becomes passive when count < zero ADD mode output operations: timed signal at Output 2, becomes active when count > Preset 2 (Activation only in positive direction). SUB mode output operations: permanent signal at Output 2, becomes active when count < zero (Activation only in negative direction) ADD mode output operations: timed signal at Output 2, becomes passive when count > Preset 2 (Deactivation only in positive direction) SUB mode output operations: permanent signal at Output 2, becomes passive when count < zero (Deactivation only in negative direction). ADD mode output operations: timed signal at Output 2, becomes active with positive direction and when count > Preset 2 and subsequently with negative direction and when count < Preset 2 SUB mode output operations: timed signal at Output 2, becomes active with negative direction and when count < zero and subsequently with positive direction and when count > zero ADD mode output operations: timed signal at Output 2, becomes passive with positive direction and when count > english Seite 15 ADD mode output operations: timed signal at Output 2, becomes passive when count ≥ Preset 2 (Deactivation only in positive direction) SUB mode output operations: permanent signal at Output 2, becomes passive when count ≤ zero (Deactivation only in negative direction) ADD mode output operations: timed signal at Output 1, becomes active when count > Preset 1. (Activation only in positive direction) SUB mode output operations: timed output at Output 1, becomes active when count < Preset 1 (Activation only in negative direction) ADD mode output operations: timed signal at Output 1, becomes passive when count > Preset 1. (Deactivation only in positive direction) SUB mode output operations: timed output at Output 1, becomes passive when count < Preset 1. (Deactivation only in negative direction). ADD mode output operations: timed signal at Output1, becomes active with positive direction and when count > Preset 1 and subsequently active with negative direction and when count < Preset 1 SUB mode output operations: timed signal at Output 1, becomes active with negative direction and when count < Preset 1 and subsequently active with positive direction and when count > Preset 1 ADD mode output operations: timed signal at Output1, becomes passive with positive direction and when count > Preset 1 and subsequently passive with negative direction and when count < Preset 1 SUB mode output operations: timed output at Output 1, becomes passive with negative direction and when count < Preset 1 and subsequently passive with positive direction and when count > Preset 1 Duration of timed signal of Output 1, programmable from 00.01 to 99.99 s. Timed signal is post-triggered ADD mode output operations: permanent signal at Output 2, becomes active when count > Preset 2 SUB mode output operations: permanent signal at Output 2, becomes active when count < zero ADD mode output operations: permanent signal at Output 2, becomes passive when count > Preset 2 SUB mode output operations: permanent signal at Output 2, becomes passive when count < zero ADD mode output operations: timed signal at Output 2, becomes active when count > Preset 2 (Activation only in positive direction). SUB mode output operations: permanent signal at Output 2, becomes active when count < zero (Activation only in negative direction) ADD mode output operations: timed signal at Output 2, becomes passive when count > Preset 2 (Deactivation only in positive direction) SUB mode output operations: permanent signal at Output 2, becomes passive when count < zero (Deactivation only in negative direction). ADD mode output operations: timed signal at Output 2, becomes active with positive direction and when count > Preset 2 and subsequently with negative direction and when count < Preset 2 SUB mode output operations: timed signal at Output 2, becomes active with negative direction and when count < zero and subsequently with positive direction and when count > zero ADD mode output operations: timed signal at Output 2, becomes passive with positive direction and when count > english Seite 15 ADD mode output operations: timed signal at Output 2, becomes active with positive direction and when count ≥ Preset 2 and subsequently with negative direction and when count ≤ Preset 2 SUB mode output operations: timed signal at Output 2, becomes active with negative direction and when count ≤ zero and subsequently with positive direction and when count ≥ zero becomes active when count > Preset 1. (Activation only in positive direction) SUB mode output operations: timed output at Output 1, becomes active when count < Preset 1 (Activation only in negative direction) ADD mode output operations: timed signal at Output 1, becomes passive when count > Preset 1. (Deactivation only in positive direction) SUB mode output operations: timed output at Output 1, becomes passive when count < Preset 1. (Deactivation only in negative direction). ADD mode output operations: timed signal at Output1, becomes active with positive direction and when count > Preset 1 and subsequently active with negative direction and when count < Preset 1 SUB mode output operations: timed signal at Output 1, becomes active with negative direction and when count < Preset 1 and subsequently active with positive direction and when count > Preset 1 ADD mode output operations: timed signal at Output1, becomes passive with positive direction and when count > Preset 1 and subsequently passive with negative direction and when count < Preset 1 SUB mode output operations: timed output at Output 1, becomes passive with negative direction and when count < Preset 1 and subsequently passive with positive direction and when count > Preset 1 Duration of timed signal of Output 1, programmable from 00.01 to 99.99 s. Timed signal is post-triggered p p permanent signal at Output 2, becomes active when count > Preset 2 SUB mode output operations: permanent signal at Output 2, becomes active when count < zero ADD mode output operations: permanent signal at Output 2, becomes passive when count > Preset 2 SUB mode output operations: permanent signal at Output 2, becomes passive when count < zero ADD mode output operations: timed signal at Output 2, becomes active when count > Preset 2 (Activation only in positive direction). SUB mode output operations: permanent signal at Output 2, becomes active when count < zero (Activation only in negative direction) ADD mode output operations: timed signal at Output 2, becomes passive when count > Preset 2 (Deactivation only in positive direction) SUB mode output operations: permanent signal at Output 2, becomes passive when count < zero (Deactivation only in negative direction). ADD mode output operations: timed signal at Output 2, becomes active with positive direction and when count > Preset 2 and subsequently with negative direction and when count < Preset 2 SUB mode output operations: timed signal at Output 2, becomes active with negative direction and when count < zero and subsequently with positive direction and when count > zero ADD mode output operations: timed signal at Output 2, becomes passive with positive direction and when count > english Seite 15 ADD mode output operations: timed signal at Output 2, becomes passive with positive direction and when count ≥ Preset 2 and subsequently with negative direction and when count ≤ Preset 2 SUB mode output operations: timed signal at Output 2, becomes passive with negative direction and when count ≤ zero and subsequently with positive direction and when count ≥ zero t.Out 2 Duration of timed signal of Output 2 Timed signal is post-triggered 00.01 Factory setting 00.01... 99.99 Programmable from 00�01 to 99�99 s factory settings are highlighted in grey Active: Relay is activated when the preset value is reached� Passive: Relay becomes de-energized when the preset value is reached�

27 8.5 Timer 8.5.1 Input Submenues for the signal and control inputs� Display Description Submenu Value InP.PoL Input polarity PnP PNP: switching to Plus for all inputs in common nPn NPN: switching to 0 V for all inputs in common FiLtEr Filter for the signal inputs InpA and InpB oFF For electronic control of the signal inputs� on For mechanical control of the signal inputs (for control with mechanical contacts)� StArt Input mode time measurement InA.Inb Start: Edge to Inp A Stop: Edge to Inp B Inb.Inb Start: 1� Edge to Inp B Stop: 2� Edge to Inp B FrErun Timing can only be controlled via the Gate input� Inp A and Inp B: no function� Auto The timer is reset by means of a RESET (to zero when adding, to preset 2 when subtracting) and then starts timing again� Timing is stopped with adding operations when preset 2 is reached� Timing is stopped with subtracting operations when zero is reached� A RESET during the timing process also causes this to stop� Inp A and Inp B: no function� GAtE Gate control for timing GAtE.Lo Timing takes place when the Gate input is not active� GAtE.hi Timing takes place when the Gate input is active� MPi User input LAtch When the MPI input is activated the display is “frozen” and remains “frozen” until the MPI input is deactivated� Internally the preset counter continues counting� tEAch When the MPI input is activated the current count value for the preset that has just been selected will be adopted as the new preset value� SEt When the MPI input is activated the preset counter will be set to the value specified in the parameter SEtPt�

28 Display Description Submenu Value Loc.InP Lock input ProG When the lock input is activated the programming is inhibited� PrESET When the lock input is activated the setting of the preset values is inhibited� PrG.PrE When the lock input is activated the setting of the preset values and the programming are both inhibited� factory settings are highlighted in grey 8.5.2 Mode Submenues for output operations� Display Description Submenu Value ModE Submenu for determining the operation of the outputs Add Count mode ADD Outputs active when count status ≥ preset value Reset to zero� Sub Count mode SUBTRACT Output 1 active when count status ≤ preset value 1. Output 2 active when count status ≤ 0. Reset to preset 2 AddAr Count mode ADDING with automatic reset Output 1 active when count status ≥ preset value 1. Output 2 (timed signal) active when count status = preset value 2� Automatic reset to zero when count status = preset value 2� Reset to zero� SubAr Count mode SUBTRACTING with automatic reset Output 1 active when count status ≤ preset value 1. Output 2 (timed signal) active when count status = 0� Automatic reset to preset 2 when count status = 0� Reset to preset 2� AddbAt Count mode ADDING with automatic reset and Batch counter Output 2 (timed signal) active when main counter = preset value 2� Automatic reset to zero when main counter = preset 2� Batch counter counts the number of automatic repetitions of preset 2� Output 1 active when Batch counter ≥ preset 1. Manual reset sets both counters to zero� Electrical reset only sets the main counter to zero�

29 Display Description Submenu Value SubbAt Count mode SUBTRACTING with automatic reset and Batch counter Output 2 (timed signal) active when main counter = zero� Automatic reset to preset 2 when main counter = zero� Batch counter counts the number of automatic repetitions of preset 2� Output 1 active when Batch counter ≥ preset 1. Manual reset sets main counter to preset value 2, batch counter to zero� Electrical reset only sets the main counter to preset value 2� Addtot Count mode ADDING with automatic reset and Total counter Output 2 (timed signal) active when main counter = preset value 2� Automatic reset to zero when main counter = preset value 2� Total counter counts all the count pulses from the main counter� Output 1 active when total counter ≥ preset value 1. Manual reset sets both counters to zero� Electrical reset only sets the main counter to zero� Subtot Count mode SUBTRACTING with automatic reset and Total counter Output 2 (timed signal) active when main counter = zero� Automatic reset to preset value 2 when main counter = zero� Total counter counts (sub from preset value 1) all count pulses from main counter� Output 1 active when Total counter ≤ zero. Manual reset sets both counters to the preset values� Electrical reset sets only main counter to preset value 2� trAiL Tracking Preset mode When preset 2 is changed then preset 1 automatically tracks it� Reset to zero� Preset 1 relative to preset 2� tr_Ar Tracking Preset mode with automatic reset When preset 2 is changed then preset 1 automatically tracks it� Reset to zero� Automatic reset to zero when main counter = preset value� factory settings are highlighted in grey

30 8.5.3 Config Submenues for matching the input pulses and display� Display Description Submenu Value tModE Unit of time SEC Unit of time: seconds Decimal point setting determines the resolution� Min Unit of time: minutes Decimal point setting determines the resolution� hour Unit of time: hours Decimal point setting determines the resolution� h.Min.S Unit of time: Hrs� Min� Sec� dp Decimal point setting (only optical function) 0 no decimal place 0.0 1 decimal place 0.00 2 decimal places 0.000 3 decimal places SetPt Set value 000000 Factory setting 000000... 999999 Set value can be programmed from 000000 to 999999� A previously programmed decimal point will be displayed� CoLor Display colour (not supported) rEd Upper line red� Lower line red� rEdGrn Upper line red Lower line green factory settings are highlighted in grey 8.5.4 Reset mode Submenues for reset mode� Display Description Submenu Value rESmd Setting the reset mode Man.EL Manual reset (with red key) and electrical reset (reset input)� no rES No reset possible (red key and reset input inhibited)� EL.rEs Only electrical reset possible (reset input)� MAnrE Only manual reset possible (red key)� factory settings are highlighted in grey

31 8.5.5 Preset 1 Submenues for preset 1� Display Description Submenu Value PrES 1 Submenu for turning preset 1 ON/OFF on Preset 1 ON off Preset 1 OFF and no function Pr.Out 1 Preset output 1 Submenu for configuration Submenu for matching the time ranges and display Unit of time Unit of time: seconds Decimal point setting determines the resolution Unit of time: minutes Decimal point setting determines the resolution Unit of time: hours Decimal point setting determines the resolution Unit of time: Hrs. Min. Sec. nt setting (Resolution) Decimal place (determines the resolution) 0 no decimal place 0.0 1 decimal place 0.00 2 decimal places 0.000 3 decimal places Set value can be programmed from 000000 to 999999 A previously programmed decimal point will be displayed o ese poss b e ( ed ey a d reset input inhibited) Only electrical reset possible (reset input) Only manual reset possible (red key) 7.8.6.5 Submenu for Preset 1 Submenu for turning preset 1 ON/OFF Preset 1 ON Preset 1 OFF and no function ADD mode output operations: permanent signal at Output 1, becomes active when count > Preset 1 SUB mode output operations: permanent signal at Output 1, becomes active when count < Preset 1 ADD mode output operations: permanent signal at Output 1, becomes passive when count > Preset 1 ADD mode output operations: permanent signal at Output 1, becomes active when count ≥ Preset 1 SUB mode output operations: permanent signal at Output 1, becomes active when count ≤ Preset 1 Submenu for matching the time ranges and display Unit of time Unit of time: seconds Decimal point setting determines the resolution Unit of time: minutes Decimal point setting determines the resolution Unit of time: hours Decimal point setting determines the resolution Unit of time: Hrs. Min. Sec. nt setting (Resolution) Decimal place (determines the resolution) 0 no decimal place 0.0 1 decimal place 0.00 2 decimal places 0.000 3 decimal places Set value can be programmed from 000000 to 999999 A previously programmed decimal point will be displayed p ) Only electrical reset possible (reset input) Only manual reset possible (red key) 7.8.6.5 Submenu for Preset 1 Submenu for turning preset 1 ON/OFF Preset 1 ON Preset 1 OFF and no function ADD mode output operations: permanent signal at Output 1, becomes active when count > Preset 1 SUB mode output operations: permanent signal at Output 1, becomes active when count < Preset 1 ADD mode output operations: permanent signal at Output 1, becomes passive when count > Preset 1 ADD mode output operations: permanent signal at Output 1, becomes passive when count ≥ Preset 1 SUB mode output operations: permanent signal at Output 1, becomes passive when count ≤ Preset 1 SUB mode output operations: permanent signal at Output 1, becomes passive when count < Preset 1 ADD mode output operations: timed signal at Output 1, becomes active when count > Preset 1. (Activation only in positive direction) SUB mode output operations: timed output at Output 1, becomes active when count < Preset 1 (Activation only in negative direction) ADD mode output operations: timed signal at Output 1, becomes passive when count > Preset 1. (Deactivation only in positive direction) SUB mode output operations: timed output at Output 1, becomes passive when count < Preset 1. (Deactivation only in negative direction). ADD mode output operations: timed signal at Output1, becomes active with positive direction and when count > Preset 1 and subsequently active with negative direction and when count < Preset 1 SUB mode output operations: timed signal at Output 1, becomes active with negative direction and when count < Preset 1 and subsequently active with positive direction and when count > Preset 1 ADD mode output operations: timed signal at Output1, becomes passive with positive direction and when count > Preset 1 and subsequently passive with negative direction and when count < Preset 1 SUB mode output operations: timed output at Output 1, becomes passive with negative direction and when count < Preset 1 and subsequently passive with positive direction and when count > Preset 1 Duration of timed signal of Output 1, programmable from 00.01 to 99.99 s. Timed signal is post-triggered 7.8.6.6 Submenu for Preset 2 Submenu for Preset 2 ADD mode output operations: permanent signal at Output 2, becomes active when count > Preset 2 SUB mode output operations: permanent signal at Output 2, becomes active when count < zero ADD mode output operations: permanent signal at Output 2, becomes passive when count > Preset 2 SUB mode output operations: permanent signal at Output 2, becomes passive when count < zero ADD mode output operations: timed signal at Output 2, becomes active when count > Preset 2 (Activation only in positive direction). SUB mode output operations: permanent signal at Output 2, becomes active when count < zero (Activation only in negative direction) ADD mode output operations: timed signal at Output 2, becomes passive when count > Preset 2 (Deactivation only in positive direction) SUB mode output operations: permanent signal at Output 2, becomes passive when count < zero (Deactivation only in negative direction). ADD mode output operations: timed signal at Output 2, becomes active with positive direction and when count > Preset 2 and subsequently with negative direction and when count < Preset 2 SUB mode output operations: timed signal at Output 2, becomes active with negative direction and when count < zero and subsequently with positive direction and when count > zero ADD mode output operations: timed signal at Output 2, becomes passive with positive direction and when count > english Seite 15 ADD mode output operations: timed signal at Output 1, becomes active when count ≥ Preset 1. (Activation only in positive direction) SUB mode output operations: timed output at Output 1, becomes active when count ≤ Preset 1 (Activation only in negative direction) SUB mode output operations: permanent signal at Output 1, becomes passive when count < Preset 1 ADD mode output operations: timed signal at Output 1, becomes active when count > Preset 1. (Activation only in positive direction) SUB mode output operations: timed output at Output 1, becomes active when count < Preset 1 (Activation only in negative direction) ADD mode output operations: timed signal at Output 1, becomes passive when count > Preset 1. (Deactivation only in positive direction) SUB mode output operations: timed output at Output 1, becomes passive when count < Preset 1. (Deactivation only in negative direction). ADD mode output operations: timed signal at Output1, becomes active with positive direction and when count > Preset 1 and subsequently active with negative direction and when count < Preset 1 SUB mode output operations: timed signal at Output 1, becomes active with negative direction and when count < Preset 1 and subsequently active with positive direction and when count > Preset 1 ADD mode output operations: timed signal at Output1, becomes passive with positive direction and when count > Preset 1 and subsequently passive with negative direction and when count < Preset 1 SUB mode output operations: timed output at Output 1, becomes passive with negative direction and when count < Preset 1 and subsequently passive with positive direction and when count > Preset 1 Duration of timed signal of Output 1, programmable from 00.01 to 99.99 s. Timed signal is post-triggered 7.8.6.6 Submenu for Preset 2 Submenu for Preset 2 ADD mode output operations: permanent signal at Output 2, becomes active when count > Preset 2 SUB mode output operations: permanent signal at Output 2, becomes active when count < zero ADD mode output operations: permanent signal at Output 2, becomes passive when count > Preset 2 SUB mode output operations: permanent signal at Output 2, becomes passive when count < zero ADD mode output operations: timed signal at Output 2, becomes active when count > Preset 2 (Activation only in positive direction). SUB mode output operations: permanent signal at Output 2, becomes active when count < zero (Activation only in negative direction) ADD mode output operations: timed signal at Output 2, becomes passive when count > Preset 2 (Deactivation only in positive direction) SUB mode output operations: permanent signal at Output 2, becomes passive when count < zero (Deactivation only in negative direction). ADD mode output operations: timed signal at Output 2, becomes active with positive direction and when count > Preset 2 and subsequently with negative direction and when count < Preset 2 SUB mode output operations: timed signal at Output 2, becomes active with negative direction and when count < zero and subsequently with positive direction and when count > zero ADD mode output operations: timed signal at Output 2, becomes passive with positive direction and when count > english Seite 15 ADD mode output operations: timed signal at Output 1, becomes passive when count ≥ Preset 1. (Deactivation only in positive direction) SUB mode output operations: timed output at Output 1, becomes passive when count ≤ Preset 1. (Deactivation only in negative direction) SUB mode output operations: permanent signal at Output 1, becomes passive when count < Preset 1 ADD mode output operations: timed signal at Output 1, becomes active when count > Preset 1. (Activation only in positive direction) SUB mode output operations: timed output at Output 1, becomes active when count < Preset 1 (Activation only in negative direction) ADD mode output operations: timed signal at Output 1, becomes passive when count > Preset 1. (Deactivation only in positive direction) SUB mode output operations: timed output at Output 1, becomes passive when count < Preset 1. (Deactivation only in negative direction). ADD mode output operations: timed signal at Output1, becomes active with positive direction and when count > Preset 1 and subsequently active with negative direction and when count < Preset 1 SUB mode output operations: timed signal at Output 1, becomes active with negative direction and when count < Preset 1 and subsequently active with positive direction and when count > Preset 1 ADD mode output operations: timed signal at Output1, becomes passive with positive direction and when count > Preset 1 and subsequently passive with negative direction and when count < Preset 1 SUB mode output operations: timed output at Output 1, becomes passive with negative direction and when count < Preset 1 and subsequently passive with positive direction and when count > Preset 1 Duration of timed signal of Output 1, programmable from 00.01 to 99.99 s. Timed signal is post-triggered 7.8.6.6 Submenu for Preset 2 Submenu for Preset 2 ADD mode output operations: permanent signal at Output 2, becomes active when count > Preset 2 SUB mode output operations: permanent signal at Output 2, becomes active when count < zero ADD mode output operations: permanent signal at Output 2, becomes passive when count > Preset 2 SUB mode output operations: permanent signal at Output 2, becomes passive when count < zero ADD mode output operations: timed signal at Output 2, becomes active when count > Preset 2 (Activation only in positive direction). SUB mode output operations: permanent signal at Output 2, becomes active when count < zero (Activation only in negative direction) ADD mode output operations: timed signal at Output 2, becomes passive when count > Preset 2 (Deactivation only in positive direction) SUB mode output operations: permanent signal at Output 2, becomes passive when count < zero (Deactivation only in negative direction). ADD mode output operations: timed signal at Output 2, becomes active with positive direction and when count > Preset 2 and subsequently with negative direction and when count < Preset 2 SUB mode output operations: timed signal at Output 2, becomes active with negative direction and when count < zero and subsequently with positive direction and when count > zero ADD mode output operations: timed signal at Output 2, becomes passive with positive direction and when count > english Seite 15 ADD mode output operations: timed signal at Output1, becomes active with positive direction and when count ≥ Preset 1 and subsequently active with negative direction and when count ≤ Preset 1 SUB mode output operations: timed signal at Output 1, becomes active with negative direction and when count ≤ Preset 1 and subsequently active with positive direction and when count ≥ Preset 1 SUB mode output operations: permanent signal at Output 1, becomes passive when count < Preset 1 ADD mode output operations: timed signal at Output 1, becomes active when count > Preset 1. (Activation only in positive direction) SUB mode output operations: timed output at Output 1, becomes active when count < Preset 1 (Activation only in negative direction) ADD mode output operations: timed signal at Output 1, becomes passive when count > Preset 1. (Deactivation only in positive direction) SUB mode output operations: timed output at Output 1, becomes passive when count < Preset 1. (Deactivation only in negative direction). ADD mode output operations: timed signal at Output1, becomes active with positive direction and when count > Preset 1 and subsequently active with negative direction and when count < Preset 1 SUB mode output operations: timed signal at Output 1, becomes active with negative direction and when count < Preset 1 and subsequently active with positive direction and when count > Preset 1 ADD mode output operations: timed signal at Output1, becomes passive with positive direction and when count > Preset 1 and subsequently passive with negative direction and when count < Preset 1 SUB mode output operations: timed output at Output 1, becomes passive with negative direction and when count < Preset 1 and subsequently passive with positive direction and when count > Preset 1 Duration of timed signal of Output 1, programmable from 00.01 to 99.99 s. Timed signal is post-triggered 7.8.6.6 Submenu for Preset 2 Submenu for Preset 2 ADD mode output operations: permanent signal at Output 2, becomes active when count > Preset 2 SUB mode output operations: permanent signal at Output 2, becomes active when count < zero ADD mode output operations: permanent signal at Output 2, becomes passive when count > Preset 2 SUB mode output operations: permanent signal at Output 2, becomes passive when count < zero ADD mode output operations: timed signal at Output 2, becomes active when count > Preset 2 (Activation only in positive direction). SUB mode output operations: permanent signal at Output 2, becomes active when count < zero (Activation only in negative direction) ADD mode output operations: timed signal at Output 2, becomes passive when count > Preset 2 (Deactivation only in positive direction) SUB mode output operations: permanent signal at Output 2, becomes passive when count < zero (Deactivation only in negative direction). ADD mode output operations: timed signal at Output 2, becomes active with positive direction and when count > Preset 2 and subsequently with negative direction and when count < Preset 2 SUB mode output operations: timed signal at Output 2, becomes active with negative direction and when count < zero and subsequently with positive direction and when count > zero ADD mode output operations: timed signal at Output 2, becomes passive with positive direction and when count > english Seite 15 ADD mode output operations: timed signal at Output1, becomes passive with positive direction and when count ≥ Preset 1 and subsequently passive with negative direction and when count ≤ Preset 1 SUB mode output operations: timed output at Output 1, becomes passive with negative direction and when count ≤ Preset 1 and subsequently passive with positive direction and when count ≥ Preset 1

32 Display Description Submenu Value t.Out 1 Duration of timed signal of Output 1 Timed signal is post-triggered 00.01 Factory setting 00.01... 99.99 Programmable from 00�01 to 99�99 s factory settings are highlighted in grey 8.5.6 Preset 2 Submenues for preset 2� Display Description Submenu Value PrES 2 Submenu for Preset 2 Pr.Out 2 Preset output 2 also section 17. Output operations) Tracking Preset mode with automatic reset When preset 2 is changed then preset 1 automatically tracks it. Reset to zero. Automatic reset to zero when main counter = preset value 2. Preset 1 relative to Preset 2 (see also section 17. Output operations) Submenu for configuration Submenu for matching the time ranges and display Unit of time Unit of time: seconds Decimal point setting determines the resolution Unit of time: minutes Decimal point setting determines the resolution Unit of time: hours Decimal point setting determines the resolution Unit of time: Hrs. Min. Sec. nt setting (Resolution) Decimal place (determines the resolution) 0 no decimal place 0.0 1 decimal place 0.00 2 decimal places 0.000 3 decimal places Set value can be programmed from 000000 to 999999 A previously programmed decimal point will be displayed p y upper line red lower line green 7.8.6.4 Submenu for reset mode Setting the reset mode Manual reset (with red key) and electrical reset (reset input) No reset possible (red key and reset input inhibited) Only electrical reset possible (reset input) Only manual reset possible (red key) 7.8.6.5 Submenu for Preset 1 Submenu for turning preset 1 ON/OFF Preset 1 ON Preset 1 OFF and no function ADD mode output operations: permanent signal at Output 1, becomes active when count > Preset 1 SUB mode output operations: permanent signal at Output 1, becomes active when count < Preset 1 ADD mode output operations: permanent signal at Output 1, becomes passive when count > Preset 1 ADD mode output operations: permanent signal at Output 2, becomes active when count ≥ Preset 2 SUB mode output operations: permanent signal at Output 2, becomes active when count ≤ zero operations) Tracking Preset mode with automatic reset When preset 2 is changed then preset 1 automatically tracks it. Reset to zero. Automatic reset to zero when main counter = preset value 2. Preset 1 relative to Preset 2 (see also section 17. Output operations) Submenu for configuration Submenu for matching the time ranges and display Unit of time Unit of time: seconds Decimal point setting determines the resolution Unit of time: minutes Decimal point setting determines the resolution Unit of time: hours Decimal point setting determines the resolution Unit of time: Hrs. Min. Sec. nt setting (Resolution) Decimal place (determines the resolution) 0 no decimal place 0.0 1 decimal place 0.00 2 decimal places 0.000 3 decimal places Set value can be programmed from 000000 to 999999 A previously programmed decimal point will be displayed pp lower line green 7.8.6.4 Submenu for reset mode Setting the reset mode Manual reset (with red key) and electrical reset (reset input) No reset possible (red key and reset input inhibited) Only electrical reset possible (reset input) Only manual reset possible (red key) 7.8.6.5 Submenu for Preset 1 Submenu for turning preset 1 ON/OFF Preset 1 ON Preset 1 OFF and no function ADD mode output operations: permanent signal at Output 1, becomes active when count > Preset 1 SUB mode output operations: permanent signal at Output 1, becomes active when count < Preset 1 ADD mode output operations: permanent signal at Output 1, becomes passive when count > Preset 1 ADD mode output operations: permanent signal at Output 2, becomes passive when count ≥ Preset 2 SUB mode output operations: permanent signal at Output 2, becomes passive when count ≤ zero SUB mode output operations: permanent signal at Output 1, becomes passive when count < Preset 1 ADD mode output operations: timed signal at Output 1, becomes active when count > Preset 1. (Activation only in positive direction) SUB mode output operations: timed output at Output 1, becomes active when count < Preset 1 (Activation only in negative direction) ADD mode output operations: timed signal at Output 1, becomes passive when count > Preset 1. (Deactivation only in positive direction) SUB mode output operations: timed output at Output 1, becomes passive when count < Preset 1. (Deactivation only in negative direction). ADD mode output operations: timed signal at Output1, becomes active with positive direction and when count > Preset 1 and subsequently active with negative direction and when count < Preset 1 SUB mode output operations: timed signal at Output 1, becomes active with negative direction and when count < Preset 1 and subsequently active with positive direction and when count > Preset 1 ADD mode output operations: timed signal at Output1, becomes passive with positive direction and when count > Preset 1 and subsequently passive with negative direction and when count < Preset 1 SUB mode output operations: timed output at Output 1 7.8.6.6 Submenu for Preset 2 Submenu for Preset 2 ADD mode output operations: permanent signal at Output 2, becomes active when count > Preset 2 SUB mode output operations: permanent signal at Output 2, becomes active when count < zero ADD mode output operations: permanent signal at Output 2, becomes passive when count > Preset 2 SUB mode output operations: permanent signal at Output 2, becomes passive when count < zero ADD mode output operations: timed signal at Output 2, becomes active when count > Preset 2 (Activation only in positive direction). SUB mode output operations: permanent signal at Output 2, becomes active when count < zero (Activation only in negative direction) ADD mode output operations: timed signal at Output 2, becomes passive when count > Preset 2 (Deactivation only in positive direction) SUB mode output operations: permanent signal at Output 2, becomes passive when count < zero (Deactivation only in negative direction). ADD mode output operations: timed signal at Output 2, becomes active with positive direction and when count > Preset 2 and subsequently with english ADD mode output operations: timed signal at Output 2, becomes active when count ≥ Preset 2 (Activation only in positive direction)� SUB mode output operations: permanent signal at Output 2, becomes active when count ≤ zero (Activation only in negative direction) SUB mode output operations: permanent signal at Output 1, becomes passive when count < Preset 1 ADD mode output operations: timed signal at Output 1, becomes active when count > Preset 1. (Activation only in positive direction) SUB mode output operations: timed output at Output 1, becomes active when count < Preset 1 (Activation only in negative direction) ADD mode output operations: timed signal at Output 1, becomes passive when count > Preset 1. (Deactivation only in positive direction) SUB mode output operations: timed output at Output 1, becomes passive when count < Preset 1. (Deactivation only in negative direction). ADD mode output operations: timed signal at Output1, becomes active with positive direction and when count > Preset 1 and subsequently active with negative direction and when count < Preset 1 SUB mode output operations: timed signal at Output 1, becomes active with negative direction and when count < Preset 1 and subsequently active with positive direction and when count > Preset 1 ADD mode output operations: timed signal at Output1, becomes passive with positive direction and when count > Preset 1 and subsequently passive with negative direction and when count < Preset 1 SUB mode output operations: timed output at Output 1 7.8.6.6 Submenu for Preset 2 Submenu for Preset 2 ADD mode output operations: permanent signal at Output 2, becomes active when count > Preset 2 SUB mode output operations: permanent signal at Output 2, becomes active when count < zero ADD mode output operations: permanent signal at Output 2, becomes passive when count > Preset 2 SUB mode output operations: permanent signal at Output 2, becomes passive when count < zero ADD mode output operations: timed signal at Output 2, becomes active when count > Preset 2 (Activation only in positive direction). SUB mode output operations: permanent signal at Output 2, becomes active when count < zero (Activation only in negative direction) ADD mode output operations: timed signal at Output 2, becomes passive when count > Preset 2 (Deactivation only in positive direction) SUB mode output operations: permanent signal at Output 2, becomes passive when count < zero (Deactivation only in negative direction). ADD mode output operations: timed signal at Output 2, becomes active with positive direction and when count > Preset 2 and subsequently with english ADD mode output operations: timed signal at Output 2, becomes passive when count ≥ Preset 2 (Deactivation only in positive direction) SUB mode output operations: permanent signal at Output 2, becomes passive when count ≤ zero (Deactivation only in negative direction) SUB mode output operations: permanent signal at Output 1, becomes passive when count < Preset 1 ADD mode output operations: timed signal at Output 1, becomes active when count > Preset 1. (Activation only in positive direction) SUB mode output operations: timed output at Output 1, becomes active when count < Preset 1 (Activation only in negative direction) ADD mode output operations: timed signal at Output 1, becomes passive when count > Preset 1. (Deactivation only in positive direction) SUB mode output operations: timed output at Output 1, becomes passive when count < Preset 1. (Deactivation only in negative direction). ADD mode output operations: timed signal at Output1, becomes active with positive direction and when count > Preset 1 and subsequently active with negative direction and when count < Preset 1 SUB mode output operations: timed signal at Output 1, becomes active with negative direction and when count < Preset 1 and subsequently active with positive direction and when count > Preset 1 ADD mode output operations: timed signal at Output1, becomes passive with positive direction and when count > Preset 1 and subsequently passive with negative direction and when count < Preset 1 SUB mode output operations: timed output at Output 1 7.8.6.6 Submenu for Preset 2 Submenu for Preset 2 ADD mode output operations: permanent signal at Output 2, becomes active when count > Preset 2 SUB mode output operations: permanent signal at Output 2, becomes active when count < zero ADD mode output operations: permanent signal at Output 2, becomes passive when count > Preset 2 SUB mode output operations: permanent signal at Output 2, becomes passive when count < zero ADD mode output operations: timed signal at Output 2, becomes active when count > Preset 2 (Activation only in positive direction). SUB mode output operations: permanent signal at Output 2, becomes active when count < zero (Activation only in negative direction) ADD mode output operations: timed signal at Output 2, becomes passive when count > Preset 2 (Deactivation only in positive direction) SUB mode output operations: permanent signal at Output 2, becomes passive when count < zero (Deactivation only in negative direction). ADD mode output operations: timed signal at Output 2, becomes active with positive direction and when count > Preset 2 and subsequently with english ADD mode output operations: timed signal at Output 2, becomes active with positive direction and when count ≥ Preset 2 and subsequently with negative direction and when count ≤ Preset 2 SUB mode output operations: timed signal at Output 2, becomes active with negative direction and when count ≤ zero and subsequently with positive direction and when count ≥ zero

33 Display Description Submenu Value direction and when count > Preset 1 and subsequently active with negative direction and when count < Preset 1 SUB mode output operations: timed signal at Output 1, becomes active with negative direction and when count < Preset 1 and subsequently active with positive direction and when count > Preset 1 ADD mode output operations: timed signal at Output1, becomes passive with positive direction and when count > Preset 1 and subsequently passive with negative direction and when count < Preset 1 SUB mode output operations: timed output at Output 1, becomes passive with negative direction and when count < Preset 1 and subsequently passive with positive direction and when count > Preset 1 Duration of timed signal of Output 1, programmable from 00.01 to 99.99 s. Timed signal is post-triggered permanent signal at Output 2, becomes active when count < zero (Activation only in negative direction) ADD mode output operations: timed signal at Output 2, becomes passive when count > Preset 2 (Deactivation only in positive direction) SUB mode output operations: permanent signal at Output 2, becomes passive when count < zero (Deactivation only in negative direction). ADD mode output operations: timed signal at Output 2, becomes active with positive direction and when count > Preset 2 and subsequently with negative direction and when count < Preset 2 SUB mode output operations: timed signal at Output 2, becomes active with negative direction and when count < zero and subsequently with positive direction and when count > zero ADD mode output operations: timed signal at Output 2, becomes passive with positive direction and when count > Seite 15 ADD mode output operations: timed signal at Output 2, becomes passive with positive direction and when count ≥ Preset 2 and subsequently with negative direction and when count ≤ Preset 2 SUB mode output operations: timed signal at Output 2, becomes passive with negative direction and when count ≤ zero and subsequently with positive direction and when count ≥ zero t.Out 2 Duration of timed signal of Output 2 Timed signal is post-triggered 00.01 Factory setting 00.01... 99.99 Programmable from 00�01 to 99�99 s factory settings are highlighted in grey Active: Relay is activated when the preset value is reached� Passive: Relay becomes de-energized when the preset value is reached�

34 8.6 Tacho/Frequency meter 8.6.1 Input Submenues for the signal and control inputs� Display Description Submenu Value InP.PoL Input polarity PnP PNP: switching to Plus for all inputs in common nPn NPN: switching to 0 V for all inputs in common FiLtEr Filter for the signal inputs InpA and InpB oFF Maximum count frequency on Damped to approx� 30 Hz (for control with mechanical contacts) InPut Input mode frequency feasurement A Simple frequency measurement Inp A: frequency input Inp B: no function ASub b Differential measurement [A-B] Inp A: frequency input A Inp B: frequency input B AAdd b Total measurement [A+B] Inp A: Frequency input A Inp B: Frequency input B quAd Frequency measurement with direction recognition [Quad] Inp A: Frequency input 0° Inp B: Frequency input 90° A / B Ratio measurement [A/B] Inp A: Frequency input A Inp B: Frequency input B A % b Percentage differential measurement [(A-B) / A in %] Inp A: Frequency input A Inp B: Frequency input B MPi User input LAtch When the MPI input is activated the display is “frozen” and remains “frozen” until the MPI input is deactivated� Internally the frequency meter continues running� tEAch When the MPI input is activated the current frequency for the preset that has just been selected will be adopted as the new preset value�

35 Display Description Submenu Value Loc.InP Lock input ProG When the lock input is activated the programming is inhibited� PrESET When the lock input is activated the setting of the preset values is inhibited� PrG.PrE When the lock input is activated the setting of the preset values and the programming are both inhibited� factory settings are highlighted in grey 8.6.2 Config Submenues for matching the input pulses and display� Display Description Submenu Value FActor Multiplication factor 01.0000 Factory setting 00.0001... 99.9999 Multiplication factor can be programmed from 00�0001 to 99�9999� The setting 00�0000 will not beaccepted� diViSo Division factor 01.0000 Factory setting 01.0000... 99.9999 Division factor can be programmed from 01�0000 to 99�9999� The setting < 01�0000 will not be accepted� tModE Display mode (time mode) SEC -1 Calculation and display of the frequency or speed in 1/s� Min -1 Calculation and display of the frequency or speed in 1/min� dp Decimal point setting (only optical function)� 0 no decimal place 0.0 1 decimal place 0.00 2 decimal places 0.000 3 decimal places AVG Moving average oFF Moving average off AVG 2 Moving average on, calculated over 2 measurements� AVG 5 Moving average on, calculated over 5 measurements� AVG 10 Moving average on, calculated over 10 measurements� AVG 20 Moving average on, calculated over 20 measurements�

36 Display Description Submenu Value StArt Start delay 00.0 Factory setting 00.0...99.9 Programmable from 00�0 to 99�9 s� At the start of a measurement the measurement results within this time- period are ignored� WAit0 Waiting time 00.1 Factory setting 00.1...99.0 Programmable from 00�1 to 99�9 s� This value specifies how much time should elapse, after the last valid edge, before zero is to be displayed� CoLor Display colour (not supported) rEd Upper line red� Lower line red� rEdGrn Upper line red Lower line green factory settings are highlighted in grey 8.6.3 Preset 1 Submenues for preset 1� Display Description Submenu Value PrES 1 Submenu for turning preset 1 ON/OFF on Preset 1 ON off Preset 1 OFF and no function Pr.Out 1 Preset output 1 eset mode When preset 2 is changed then preset 1 automatically tracks it. Reset to zero Preset 1 relative to preset 2 (see also section 17. Output operations) Tracking Preset mode with automatic reset When preset 2 is changed then preset 1 automatically tracks it. Reset to zero. Automatic reset to zero when main counter = preset value 2. Preset 1 relative to Preset 2 (see also section 17. Output operations) Submenu for configuration Submenu for matching the time ranges and display Unit of time Unit of time: seconds Decimal point setting determines the resolution Unit of time: minutes Decimal point setting determines the resolution Unit of time: hours Decimal point setting determines the resolution Unit of time: Hrs. Min. Sec. nt setting (Resolution) Decimal place (determines the resolution) 0 no decimal place 0.0 1 decimal place 0.00 2 decimal places 0.000 3 decimal places Set value can be programmed from 000000 to 999999 A previously programmed decimal point will be displayed Display colour (for 6.92x.x1x3.xx0] Display colour upper line red lower line red Display colour upper line red lower line green 7.8.6.4 Submenu for reset mode Setting the reset mode Manual reset (with red key) and electrical reset (reset input) No reset possible (red key and reset input inhibited) Only electrical reset possible (reset input) Only manual reset possible (red key) 7.8.6.5 Submenu for Preset 1 Submenu for turning preset 1 ON/OFF Preset 1 ON Preset 1 OFF and no function ADD mode output operations: permanent signal at Output 1, becomes active when count > Preset 1 SUB mode output operations: permanent signal at Output 1, becomes active when count < Preset 1 ADD mode output operations: permanent signal at Output 1, becomes passive when count > Preset 1 ADD mode output operations: permanent signal at Output 1, becomes active when count ≥ Preset 1 SUB mode output operations: permanent signal at Output 1, becomes active when count ≤ Preset 1 eset mode When preset 2 is changed then preset 1 automatically tracks it. Reset to zero Preset 1 relative to preset 2 (see also section 17. Output operations) Tracking Preset mode with automatic reset When preset 2 is changed then preset 1 automatically tracks it. Reset to zero. Automatic reset to zero when main counter = preset value 2. Preset 1 relative to Preset 2 (see also section 17. Output operations) Submenu for configuration Submenu for matching the time ranges and display Unit of time Unit of time: seconds Decimal point setting determines the resolution Unit of time: minutes Decimal point setting determines the resolution Unit of time: hours Decimal point setting determines the resolution Unit of time: Hrs. Min. Sec. nt setting (Resolution) Decimal place (determines the resolution) 0 no decimal place 0.0 1 decimal place 0.00 2 decimal places 0.000 3 decimal places Set value can be programmed from 000000 to 999999 A previously programmed decimal point will be displayed Display colour (for 6.92x.x1x3.xx0] Display colour upper line red lower line red Display colour upper line red lower line green 7.8.6.4 Submenu for reset mode Setting the reset mode Manual reset (with red key) and electrical reset (reset input) No reset possible (red key and reset input inhibited) Only electrical reset possible (reset input) Only manual reset possible (red key) 7.8.6.5 Submenu for Preset 1 Submenu for turning preset 1 ON/OFF Preset 1 ON Preset 1 OFF and no function ADD mode output operations: permanent signal at Output 1, becomes active when count > Preset 1 SUB mode output operations: permanent signal at Output 1, becomes active when count < Preset 1 ADD mode output operations: permanent signal at Output 1, becomes passive when count > Preset 1 ADD mode output operations: permanent signal at Output 1, becomes passive when count ≥ Preset 1 SUB mode output operations: permanent signal at Output 1, becomes passive when count ≤ Preset 1 SUB mode output operations: permanent signal at Output 1, becomes passive when count < Preset 1 ADD mode output operations: timed signal at Output 1, becomes active when count > Preset 1. (Activation only in positive direction) SUB mode output operations: timed output at Output 1, becomes active when count < Preset 1 (Activation only in negative direction) ADD mode output operations: timed signal at Output 1, becomes passive when count > Preset 1. (Deactivation only in positive direction) SUB mode output operations: timed output at Output 1, b i h t 7.8.6.6 Submenu for Preset 2 Submenu for Preset 2 ADD mode output operations: permanent signal at Output 2, becomes active when count > Preset 2 SUB mode output operations: permanent signal at Output 2, becomes active when count < zero ADD mode output operations: permanent signal at Output 2, becomes passive when count > Preset 2 SUB mode output operations: permanent signal at Output 2, becomes passive when count < zero english ADD mode output operations: timed signal at Output 1, becomes active when count ≥ Preset 1. (Activation only in positive direction) SUB mode output operations: timed output at Output 1, becomes active when count ≤ Preset 1 (Activation only in negative direction)

37 Display Description Submenu Value Preset 1 ADD mode output operations: timed signal at Output 1, becomes active when count > Preset 1. (Activation only in positive direction) SUB mode output operations: timed output at Output 1, becomes active when count < Preset 1 (Activation only in negative direction) ADD mode output operations: timed signal at Output 1, becomes passive when count > Preset 1. (Deactivation only in positive direction) SUB mode output operations: timed output at Output 1, becomes passive when count < Preset 1. (Deactivation only in negative direction). ADD mode output operations: timed signal at Output1, becomes active with positive direction and when count > Preset 1 and subsequently active with negative direction and when count < Preset 1 SUB mode output operations: timed signal at Output 1, becomes active with negative direction and when count < Preset 1 and subsequently active with positive direction and when count > Preset 1 ADD mode output operations: timed signal at Output1, becomes passive with positive direction and when count > Preset 1 and subsequently passive with negative direction and when count < Preset 1 SUB mode output operations: timed output at Output 1, becomes passive with negative direction and when count < Preset 1 and subsequently passive with positive direction and when count > Preset 1 Duration of timed signal of Output 1, programmable from 00.01 to 99.99 s. Timed signal is post-triggered ADD mode output operations: permanent signal at Output 2, becomes active when count > Preset 2 SUB mode output operations: permanent signal at Output 2, becomes active when count < zero ADD mode output operations: permanent signal at Output 2, becomes passive when count > Preset 2 SUB mode output operations: permanent signal at Output 2, becomes passive when count < zero ADD mode output operations: timed signal at Output 2, becomes active when count > Preset 2 (Activation only in positive direction). SUB mode output operations: permanent signal at Output 2, becomes active when count < zero (Activation only in negative direction) ADD mode output operations: timed signal at Output 2, becomes passive when count > Preset 2 (Deactivation only in positive direction) SUB mode output operations: permanent signal at Output 2, becomes passive when count < zero (Deactivation only in negative direction). ADD mode output operations: timed signal at Output 2, becomes active with positive direction and when count > Preset 2 and subsequently with negative direction and when count < Preset 2 SUB mode output operations: timed signal at Output 2, becomes active with negative direction and when count < zero and subsequently with positive direction and when count > zero ADD mode output operations: timed signal at Output 2, becomes passive with positive direction and when count > english Seite 15 ADD mode output operations: timed signal at Output 1, becomes passive when count ≥ Preset 1. (Deactivation only in positive direction) SUB mode output operations: timed output at Output 1, becomes passive when count ≤ Preset 1. (Deactivation only in negative direction) ADD mode output operations: timed signal at Output 1, becomes active when count > Preset 1. (Activation only in positive direction) SUB mode output operations: timed output at Output 1, becomes active when count < Preset 1 (Activation only in negative direction) ADD mode output operations: timed signal at Output 1, becomes passive when count > Preset 1. (Deactivation only in positive direction) SUB mode output operations: timed output at Output 1, becomes passive when count < Preset 1. (Deactivation only in negative direction). ADD mode output operations: timed signal at Output1, becomes active with positive direction and when count > Preset 1 and subsequently active with negative direction and when count < Preset 1 SUB mode output operations: timed signal at Output 1, becomes active with negative direction and when count < Preset 1 and subsequently active with positive direction and when count > Preset 1 ADD mode output operations: timed signal at Output1, becomes passive with positive direction and when count > Preset 1 and subsequently passive with negative direction and when count < Preset 1 SUB mode output operations: timed output at Output 1, becomes passive with negative direction and when count < Preset 1 and subsequently passive with positive direction and when count > Preset 1 Duration of timed signal of Output 1, programmable from 00.01 to 99.99 s. Timed signal is post-triggered ADD mode output operations: permanent signal at Output 2, becomes active when count > Preset 2 SUB mode output operations: permanent signal at Output 2, becomes active when count < zero ADD mode output operations: permanent signal at Output 2, becomes passive when count > Preset 2 SUB mode output operations: permanent signal at Output 2, becomes passive when count < zero ADD mode output operations: timed signal at Output 2, becomes active when count > Preset 2 (Activation only in positive direction). SUB mode output operations: permanent signal at Output 2, becomes active when count < zero (Activation only in negative direction) ADD mode output operations: timed signal at Output 2, becomes passive when count > Preset 2 (Deactivation only in positive direction) SUB mode output operations: permanent signal at Output 2, becomes passive when count < zero (Deactivation only in negative direction). ADD mode output operations: timed signal at Output 2, becomes active with positive direction and when count > Preset 2 and subsequently with negative direction and when count < Preset 2 SUB mode output operations: timed signal at Output 2, becomes active with negative direction and when count < zero and subsequently with positive direction and when count > zero ADD mode output operations: timed signal at Output 2, becomes passive with positive direction and when count > english Seite 15 ADD mode output operations: timed signal at Output1, becomes active with positive direction and when count ≥ Preset 1 and subsequently active with negative direction and when count ≤ Preset 1 SUB mode output operations: timed signal at Output 1, becomes active with negative direction and when count ≤ Preset 1 and subsequently active with positive direction and when count ≥ Preset 1 ADD mode output operations: timed signal at Output 1, becomes active when count > Preset 1. (Activation only in positive direction) SUB mode output operations: timed output at Output 1, becomes active when count < Preset 1 (Activation only in negative direction) ADD mode output operations: timed signal at Output 1, becomes passive when count > Preset 1. (Deactivation only in positive direction) SUB mode output operations: timed output at Output 1, becomes passive when count < Preset 1. (Deactivation only in negative direction). ADD mode output operations: timed signal at Output1, becomes active with positive direction and when count > Preset 1 and subsequently active with negative direction and when count < Preset 1 SUB mode output operations: timed signal at Output 1, becomes active with negative direction and when count < Preset 1 and subsequently active with positive direction and when count > Preset 1 ADD mode output operations: timed signal at Output1, becomes passive with positive direction and when count > Preset 1 and subsequently passive with negative direction and when count < Preset 1 SUB mode output operations: timed output at Output 1, becomes passive with negative direction and when count < Preset 1 and subsequently passive with positive direction and when count > Preset 1 Duration of timed signal of Output 1, programmable from 00.01 to 99.99 s. Timed signal is post-triggered ADD mode output operations: permanent signal at Output 2, becomes active when count > Preset 2 SUB mode output operations: permanent signal at Output 2, becomes active when count < zero ADD mode output operations: permanent signal at Output 2, becomes passive when count > Preset 2 SUB mode output operations: permanent signal at Output 2, becomes passive when count < zero ADD mode output operations: timed signal at Output 2, becomes active when count > Preset 2 (Activation only in positive direction). SUB mode output operations: permanent signal at Output 2, becomes active when count < zero (Activation only in negative direction) ADD mode output operations: timed signal at Output 2, becomes passive when count > Preset 2 (Deactivation only in positive direction) SUB mode output operations: permanent signal at Output 2, becomes passive when count < zero (Deactivation only in negative direction). ADD mode output operations: timed signal at Output 2, becomes active with positive direction and when count > Preset 2 and subsequently with negative direction and when count < Preset 2 SUB mode output operations: timed signal at Output 2, becomes active with negative direction and when count < zero and subsequently with positive direction and when count > zero ADD mode output operations: timed signal at Output 2, becomes passive with positive direction and when count > english Seite 15 ADD mode output operations: timed signal at Output1, becomes passive with positive direction and when count ≥ Preset 1 and subsequently passive with negative direction and when count ≤ Preset 1 SUB mode output operations: timed output at Output 1, becomes passive with negative direction and when count ≤ Preset 1 and subsequently passive with positive direction and when count ≥ Preset 1 t.Out 1 Duration of timed signal of Output 1 Timed signal is post-triggered 00.01 Factory setting 00.01... 99.99 Programmable from 00�01 to 99�99 s factory settings are highlighted in grey 8.6.4 Preset 2 Submenues for preset 2� Display Description Submenu Value PrES 2 Submenu for Preset 2 Pr.Out 2 Preset output 2 eset mode When preset 2 is changed then preset 1 automatically tracks it. Reset to zero Preset 1 relative to preset 2 (see also section 17. Output operations) Tracking Preset mode with automatic reset When preset 2 is changed then preset 1 automatically tracks it. Reset to zero. Automatic reset to zero when main counter = preset value 2. Preset 1 relative to Preset 2 (see also section 17. Output operations) Submenu for configuration Submenu for matching the time ranges and display Unit of time Unit of time: seconds Decimal point setting determines the resolution Unit of time: minutes Decimal point setting determines the resolution Unit of time: hours Decimal point setting determines the resolution Unit of time: Hrs. Min. Sec. nt setting (Resolution) Decimal place (determines the resolution) 0 no decimal place 0.0 1 decimal place 0.00 2 decimal places 0.000 3 decimal places Set value can be programmed from 000000 to 999999 A previously programmed decimal point will be displayed Display colour (for 6.92x.x1x3.xx0] Display colour upper line red lower line red Display colour upper line red lower line green 7.8.6.4 Submenu for reset mode Setting the reset mode Manual reset (with red key) and electrical reset (reset input) No reset possible (red key and reset input inhibited) Only electrical reset possible (reset input) Only manual reset possible (red key) 7.8.6.5 Submenu for Preset 1 Submenu for turning preset 1 ON/OFF Preset 1 ON Preset 1 OFF and no function ADD mode output operations: permanent signal at Output 1, becomes active when count > Preset 1 SUB mode output operations: permanent signal at Output 1, becomes active when count < Preset 1 ADD mode output operations: permanent signal at Output 1, becomes passive when count > Preset 1 ADD mode output operations: permanent signal at Output 2, becomes active when count ≥ Preset 2 SUB mode output operations: permanent signal at Output 2, becomes active when count ≤ zero eset mode When preset 2 is changed then preset 1 automatically tracks it. Reset to zero Preset 1 relative to preset 2 (see also section 17. Output operations) Tracking Preset mode with automatic reset When preset 2 is changed then preset 1 automatically tracks it. Reset to zero. Automatic reset to zero when main counter = preset value 2. Preset 1 relative to Preset 2 (see also section 17. Output operations) Submenu for configuration Submenu for matching the time ranges and display Unit of time Unit of time: seconds Decimal point setting determines the resolution Unit of time: minutes Decimal point setting determines the resolution Unit of time: hours Decimal point setting determines the resolution Unit of time: Hrs. Min. Sec. nt setting (Resolution) Decimal place (determines the resolution) 0 no decimal place 0.0 1 decimal place 0.00 2 decimal places 0.000 3 decimal places Set value can be programmed from 000000 to 999999 A previously programmed decimal point will be displayed Display colour (for 6.92x.x1x3.xx0] Display colour upper line red lower line red Display colour upper line red lower line green 7.8.6.4 Submenu for reset mode Setting the reset mode Manual reset (with red key) and electrical reset (reset input) No reset possible (red key and reset input inhibited) Only electrical reset possible (reset input) Only manual reset possible (red key) 7.8.6.5 Submenu for Preset 1 Submenu for turning preset 1 ON/OFF Preset 1 ON Preset 1 OFF and no function ADD mode output operations: permanent signal at Output 1, becomes active when count > Preset 1 SUB mode output operations: permanent signal at Output 1, becomes active when count < Preset 1 ADD mode output operations: permanent signal at Output 1, becomes passive when count > Preset 1 ADD mode output operations: permanent signal at Output 2, becomes passive when count ≥ Preset 2 SUB mode output operations: permanent signal at Output 2, becomes passive when count ≤ zero

38 Display Description Submenu Value SUB mode output operations: permanent signal at Output 1, becomes passive when count < Preset 1 ADD mode output operations: timed signal at Output 1, becomes active when count > Preset 1. (Activation only in positive direction) SUB mode output operations: timed output at Output 1, becomes active when count < Preset 1 (Activation only in negative direction) ADD mode output operations: timed signal at Output 1, becomes passive when count > Preset 1. (Deactivation only in positive direction) SUB mode output operations: timed output at Output 1, becomes passive when count < Preset 1. (Deactivation only in negative direction). ADD mode output operations: timed signal at Output1, becomes active with positive direction and when count > Preset 1 and subsequently active with negative direction and when count < Preset 1 SUB mode output operations: timed signal at Output 1, becomes active with negative direction and when count < Preset 1 and subsequently active with positive direction and when count > Preset 1 ADD mode output operations: timed signal at Output1, becomes passive with positive direction and when count > Preset 1 and subsequently passive with negative direction and when count < Preset 1 SUB mode output operations: timed output at Output 1, becomes passive with negative direction and when count < Preset 1 and subsequently passive with positive direction and when count > Preset 1 Duration of timed signal of Output 1, programmable from 00.01 to 99.99 s. Timed signal is post-triggered 7.8.6.6 Submenu for Preset 2 Submenu for Preset 2 ADD mode output operations: permanent signal at Output 2, becomes active when count > Preset 2 SUB mode output operations: permanent signal at Output 2, becomes active when count < zero ADD mode output operations: permanent signal at Output 2, becomes passive when count > Preset 2 SUB mode output operations: permanent signal at Output 2, becomes passive when count < zero ADD mode output operations: timed signal at Output 2, becomes active when count > Preset 2 (Activation only in positive direction). SUB mode output operations: permanent signal at Output 2, becomes active when count < zero (Activation only in negative direction) ADD mode output operations: timed signal at Output 2, becomes passive when count > Preset 2 (Deactivation only in positive direction) SUB mode output operations: permanent signal at Output 2, becomes passive when count < zero (Deactivation only in negative direction). ADD mode output operations: timed signal at Output 2, becomes active with positive direction and when count > Preset 2 and subsequently with negative direction and when count < Preset 2 SUB mode output operations: timed signal at Output 2, becomes active with negative direction and when count < zero and subsequently with positive direction and when count > zero ADD mode output operations: timed signal at Output 2, becomes passive with positive direction and when count > english Seite 15 ADD mode output operations: timed signal at Output 2, becomes active when count ≥ Preset 2 (Activation only in positive direction)� SUB mode output operations: permanent signal at Output 2, becomes active when count ≤ zero (Activation only in negative direction) SUB mode output operations: permanent signal at Output 1, becomes passive when count < Preset 1 ADD mode output operations: timed signal at Output 1, becomes active when count > Preset 1. (Activation only in positive direction) SUB mode output operations: timed output at Output 1, becomes active when count < Preset 1 (Activation only in negative direction) ADD mode output operations: timed signal at Output 1, becomes passive when count > Preset 1. (Deactivation only in positive direction) SUB mode output operations: timed output at Output 1, becomes passive when count < Preset 1. (Deactivation only in negative direction). ADD mode output operations: timed signal at Output1, becomes active with positive direction and when count > Preset 1 and subsequently active with negative direction and when count < Preset 1 SUB mode output operations: timed signal at Output 1, becomes active with negative direction and when count < Preset 1 and subsequently active with positive direction and when count > Preset 1 ADD mode output operations: timed signal at Output1, becomes passive with positive direction and when count > Preset 1 and subsequently passive with negative direction and when count < Preset 1 SUB mode output operations: timed output at Output 1, becomes passive with negative direction and when count < Preset 1 and subsequently passive with positive direction and when count > Preset 1 Duration of timed signal of Output 1, programmable from 00.01 to 99.99 s. Timed signal is post-triggered 7.8.6.6 Submenu for Preset 2 Submenu for Preset 2 ADD mode output operations: permanent signal at Output 2, becomes active when count > Preset 2 SUB mode output operations: permanent signal at Output 2, becomes active when count < zero ADD mode output operations: permanent signal at Output 2, becomes passive when count > Preset 2 SUB mode output operations: permanent signal at Output 2, becomes passive when count < zero ADD mode output operations: timed signal at Output 2, becomes active when count > Preset 2 (Activation only in positive direction). SUB mode output operations: permanent signal at Output 2, becomes active when count < zero (Activation only in negative direction) ADD mode output operations: timed signal at Output 2, becomes passive when count > Preset 2 (Deactivation only in positive direction) SUB mode output operations: permanent signal at Output 2, becomes passive when count < zero (Deactivation only in negative direction). ADD mode output operations: timed signal at Output 2, becomes active with positive direction and when count > Preset 2 and subsequently with negative direction and when count < Preset 2 SUB mode output operations: timed signal at Output 2, becomes active with negative direction and when count < zero and subsequently with positive direction and when count > zero ADD mode output operations: timed signal at Output 2, becomes passive with positive direction and when count > english Seite 15 ADD mode output operations: timed signal at Output 2, becomes passive when count ≥ Preset 2 (Deactivation only in positive direction) SUB mode output operations: permanent signal at Output 2, becomes passive when count ≤ zero (Deactivation only in negative direction) SUB mode output operations: permanent signal at Output 1, becomes passive when count < Preset 1 ADD mode output operations: timed signal at Output 1, becomes active when count > Preset 1. (Activation only in positive direction) SUB mode output operations: timed output at Output 1, becomes active when count < Preset 1 (Activation only in negative direction) ADD mode output operations: timed signal at Output 1, becomes passive when count > Preset 1. (Deactivation only in positive direction) SUB mode output operations: timed output at Output 1, becomes passive when count < Preset 1. (Deactivation only in negative direction). ADD mode output operations: timed signal at Output1, becomes active with positive direction and when count > Preset 1 and subsequently active with negative direction and when count < Preset 1 SUB mode output operations: timed signal at Output 1, becomes active with negative direction and when count < Preset 1 and subsequently active with positive direction and when count > Preset 1 ADD mode output operations: timed signal at Output1, becomes passive with positive direction and when count > Preset 1 and subsequently passive with negative direction and when count < Preset 1 SUB mode output operations: timed output at Output 1, becomes passive with negative direction and when count < Preset 1 and subsequently passive with positive direction and when count > Preset 1 Duration of timed signal of Output 1, programmable from 00.01 to 99.99 s. Timed signal is post-triggered 7.8.6.6 Submenu for Preset 2 Submenu for Preset 2 ADD mode output operations: permanent signal at Output 2, becomes active when count > Preset 2 SUB mode output operations: permanent signal at Output 2, becomes active when count < zero ADD mode output operations: permanent signal at Output 2, becomes passive when count > Preset 2 SUB mode output operations: permanent signal at Output 2, becomes passive when count < zero ADD mode output operations: timed signal at Output 2, becomes active when count > Preset 2 (Activation only in positive direction). SUB mode output operations: permanent signal at Output 2, becomes active when count < zero (Activation only in negative direction) ADD mode output operations: timed signal at Output 2, becomes passive when count > Preset 2 (Deactivation only in positive direction) SUB mode output operations: permanent signal at Output 2, becomes passive when count < zero (Deactivation only in negative direction). ADD mode output operations: timed signal at Output 2, becomes active with positive direction and when count > Preset 2 and subsequently with negative direction and when count < Preset 2 SUB mode output operations: timed signal at Output 2, becomes active with negative direction and when count < zero and subsequently with positive direction and when count > zero ADD mode output operations: timed signal at Output 2, becomes passive with positive direction and when count > english Seite 15 ADD mode output operations: timed signal at Output 2, becomes active with positive direction and when count ≥ Preset 2 and subsequently with negative direction and when count ≤ Preset 2 SUB mode output operations: timed signal at Output 2, becomes active with negative direction and when count ≤ zero and subsequently with positive direction and when count ≥ zero SUB mode output operations: permanent signal at Output 1, becomes passive when count < Preset 1 ADD mode output operations: timed signal at Output 1, becomes active when count > Preset 1. (Activation only in positive direction) SUB mode output operations: timed output at Output 1, becomes active when count < Preset 1 (Activation only in negative direction) ADD mode output operations: timed signal at Output 1, becomes passive when count > Preset 1. (Deactivation only in positive direction) SUB mode output operations: timed output at Output 1, becomes passive when count < Preset 1. (Deactivation only in negative direction). ADD mode output operations: timed signal at Output1, becomes active with positive direction and when count > Preset 1 and subsequently active with negative direction and when count < Preset 1 SUB mode output operations: timed signal at Output 1, becomes active with negative direction and when count < Preset 1 and subsequently active with positive direction and when count > Preset 1 ADD mode output operations: timed signal at Output1, becomes passive with positive direction and when count > Preset 1 and subsequently passive with negative direction and when count < Preset 1 SUB mode output operations: timed output at Output 1, becomes passive with negative direction and when count < Preset 1 and subsequently passive with positive direction and when count > Preset 1 Duration of timed signal of Output 1, programmable from 00.01 to 99.99 s. Timed signal is post-triggered 7.8.6.6 Submenu for Preset 2 Submenu for Preset 2 ADD mode output operations: permanent signal at Output 2, becomes active when count > Preset 2 SUB mode output operations: permanent signal at Output 2, becomes active when count < zero ADD mode output operations: permanent signal at Output 2, becomes passive when count > Preset 2 SUB mode output operations: permanent signal at Output 2, becomes passive when count < zero ADD mode output operations: timed signal at Output 2, becomes active when count > Preset 2 (Activation only in positive direction). SUB mode output operations: permanent signal at Output 2, becomes active when count < zero (Activation only in negative direction) ADD mode output operations: timed signal at Output 2, becomes passive when count > Preset 2 (Deactivation only in positive direction) SUB mode output operations: permanent signal at Output 2, becomes passive when count < zero (Deactivation only in negative direction). ADD mode output operations: timed signal at Output 2, becomes active with positive direction and when count > Preset 2 and subsequently with negative direction and when count < Preset 2 SUB mode output operations: timed signal at Output 2, becomes active with negative direction and when count < zero and subsequently with positive direction and when count > zero ADD mode output operations: timed signal at Output 2, becomes passive with positive direction and when count > english Seite 15 ADD mode output operations: timed signal at Output 2, becomes passive with positive direction and when count ≥ Preset 2 and subsequently with negative direction and when count ≤ Preset 2 SUB mode output operations: timed signal at Output 2, becomes passive with negative direction and when count ≤ zero and subsequently with positive direction and when count ≥ zero t.Out 2 Duration of timed signal of Output 2 Timed signal is post-triggered 00.01 Factory setting 00.01... 99.99 Programmable from 00�01 to 99�99 s factory settings are highlighted in grey Active: Relay is activated when the preset value is reached� Passive: Relay becomes de-energized when the preset value is reached�

39 9 Diagrams 9.1 Input modes 9.1.1 Pulse counting Function Diagram Cnt.Dir 14 Input modes: Pulse counting Function Diagram Note: No counting when GATE input is active P = Preset PNP: Count on rising edge NPN: Count on falling edge Cnt.Dir Inp A: Count input Inp B: Count direction Add: Display 0 --> Preset Sub: Display Preset -> 0 Up.Dn Inp A: Count input add Inp B: Count input sub Add: Display 0 --> Preset Sub: Display Preset -> 0 Up.Up Inp A: Count input 1 add Inp B: Count input 2 add Add: Display 0 --> Preset Quad A 90° B Inp A: Count input Count on one edge Inp B: Reverse direction Add: Display 0 --> Preset Sub: Display Preset -> 0 Quad 2 A 90° B Inp A: Count input Count on rising and on falling edges Inp B: Reverse direction Add: Display 0 --> Preset Sub: Display Preset -> 0 Seite 20 Inp A: Count input Inp B: Count direction Add: Display 0 → Preset Sub: Display Preset → 0 Up.Dn 14 Input modes: Pulse counting Function Diagram Note: No counting when GATE input is active P = Preset PNP: Count on rising edge NPN: Count on falling edge Cnt.Dir Inp A: Count input Inp B: Count direction Add: Display 0 --> Preset Sub: Display Preset -> 0 Up.Dn Inp A: Count input add Inp B: Count input sub Add: Display 0 --> Preset Sub: Display Preset -> 0 Up.Up Inp A: Count input 1 add Inp B: Count input 2 add Add: Display 0 --> Preset Quad A 90° B Inp A: Count input Count on one edge Inp B: Reverse direction Add: Display 0 --> Preset Sub: Display Preset -> 0 Quad 2 A 90° B Inp A: Count input Count on rising and on falling edges Inp B: Reverse direction Add: Display 0 --> Preset Sub: Display Preset -> 0 Seite 20 Inp A: Count input add Inp B: Count input sub Add: Display 0 → Preset Sub: Display Preset → 0 Up.Up 14 Input modes: Pulse counting Function Diagram Note: No counting when GATE input is active P = Preset PNP: Count on rising edge NPN: Count on falling edge Cnt.Dir Inp A: Count input Inp B: Count direction Add: Display 0 --> Preset Sub: Display Preset -> 0 Up.Dn Inp A: Count input add Inp B: Count input sub Add: Display 0 --> Preset Sub: Display Preset -> 0 Up.Up Inp A: Count input 1 add Inp B: Count input 2 add Add: Display 0 --> Preset Quad A 90° B Inp A: Count input Count on one edge Inp B: Reverse direction Add: Display 0 --> Preset Sub: Display Preset -> 0 Quad 2 A 90° B Inp A: Count input Count on rising and on falling edges Inp B: Reverse direction Add: Display 0 --> Preset Sub: Display Preset -> 0 Seite 20 Inp A: Count input 1 add Inp B: Count input 2 add Add: Display 0 → Preset Quad 14 Input modes: Pulse counting Function Diagram Note: No counting when GATE input is active P = Preset PNP: Count on rising edge NPN: Count on falling edge Cnt.Dir Inp A: Count input Inp B: Count direction Add: Display 0 --> Preset Sub: Display Preset -> 0 Up.Dn Inp A: Count input add Inp B: Count input sub Add: Display 0 --> Preset Sub: Display Preset -> 0 Up.Up Inp A: Count input 1 add Inp B: Count input 2 add Add: Display 0 --> Preset Quad A 90° B Inp A: Count input Count on one edge Inp B: Reverse direction Add: Display 0 --> Preset Sub: Display Preset -> 0 Quad 2 A 90° B Inp A: Count input Count on rising and on falling edges Inp B: Reverse direction Add: Display 0 --> Preset Sub: Display Preset -> 0 Seite 20 A 90° B Inp A: Count input Count on one edge Inp B: Reverse direction Add: Display 0 → Preset Sub: Display Preset → 0 Quad 2 14 Input modes: Pulse counting Function Diagram Note: No counting when GATE input is active P = Preset PNP: Count on rising edge NPN: Count on falling edge Cnt.Dir Inp A: Count input Inp B: Count direction Add: Display 0 --> Preset Sub: Display Preset -> 0 Up.Dn Inp A: Count input add Inp B: Count input sub Add: Display 0 --> Preset Sub: Display Preset -> 0 Up.Up Inp A: Count input 1 add Inp B: Count input 2 add Add: Display 0 --> Preset Quad A 90° B Inp A: Count input Count on one edge Inp B: Reverse direction Add: Display 0 --> Preset Sub: Display Preset -> 0 Quad 2 A 90° B Inp A: Count input Count on rising and on falling edges Inp B: Reverse direction Add: Display 0 --> Preset Sub: Display Preset -> 0 Seite 20 A 90° B Inp A: Count input Count on rising and on falling edges Inp B: Reverse direction Add: Display 0 → Preset Sub: Display Preset → 0

40 Function Diagram Quad 4 Function Diagram Note: No counting when GATE input is active PNP: Count on rising edge NPN: Count on falling edge Quad 4 A 90° B Inp A: Count input Count on rising and on falling edges Inp B: Count input Count on rising and on falling edges, Reverse direction Add: Display 0 --> Preset Sub: Display Preset -> 0 A / B Inp A: Count input 1 Inp B: Count input 2 Formula: A / B (A-B)/A Inp A: Count input 1 Inp B: Count input 2 Formula: (A � B)/A x100 english Seite 21 A 90° B Inp A: Count input Count on rising and on falling edges Inp B: Count input Count on rising and on falling edges, Reverse direction Add: Display 0 → Preset Sub: Display Preset → 0 A / B Function Diagram Note: No counting when GATE input is active PNP: Count on rising edge NPN: Count on falling edge Quad 4 A 90° B Inp A: Count input Count on rising and on falling edges Inp B: Count input Count on rising and on falling edges, Reverse direction Add: Display 0 --> Preset Sub: Display Preset -> 0 A / B Inp A: Count input 1 Inp B: Count input 2 Formula: A / B (A-B)/A Inp A: Count input 1 Inp B: Count input 2 Formula: (A � B)/A x100 english Seite 21 Inp A: Count input 1 Inp B: Count input 2 Formula: A/B (A-B)/A Function Diagram Note: No counting when GATE input is active PNP: Count on rising edge NPN: Count on falling edge Quad 4 A 90° B Inp A: Count input Count on rising and on falling edges Inp B: Count input Count on rising and on falling edges, Reverse direction Add: Display 0 --> Preset Sub: Display Preset -> 0 A / B Inp A: Count input 1 Inp B: Count input 2 Formula: A / B (A-B)/A Inp A: Count input 1 Inp B: Count input 2 Formula: (A � B)/A x100 english Seite 21 Inp A: Count input 1 Inp B: Count input 2 Formula: (A-B)/A x100 No counting when GATE input is active P = Preset PNP: Count on rising edge NPN: Count on falling edge

41 9.1.2 Timing Function Diagram InA.InB 15 Input modes: Timing Function Diagram PNP: Count on rising edge NPN: Count on falling edge InA.InB Inp A: Start Inp B: Stop Add: Display 0 --> Preset Sub: Display Preset -> 0 InB.InB Inp A: no function Inp B: Start/Stop Add: Display 0 --> Preset Sub: Display Preset -> 0 FrRrun Inp A: no function Inp B: no function Control of the timing only via the GATE input Add: Display 0 --> Preset Sub: Display Preset -> 0 Auto Inp A: no function Inp B: no function Control of the timing via RESET (manual or electrical) Add: Display 0 --> Preset Sub: Display Preset -> 0 Seite 22 Inp A: Start Inp B: Stop Add: Display 0 → Preset Sub: Display Preset → 0 InB.InB 15 Input modes: Timing Function Diagram PNP: Count on rising edge NPN: Count on falling edge InA.InB Inp A: Start Inp B: Stop Add: Display 0 --> Preset Sub: Display Preset -> 0 InB.InB Inp A: no function Inp B: Start/Stop Add: Display 0 --> Preset Sub: Display Preset -> 0 FrRrun Inp A: no function Inp B: no function Control of the timing only via the GATE input Add: Display 0 --> Preset Sub: Display Preset -> 0 Auto Inp A: no function Inp B: no function Control of the timing via RESET (manual or electrical) Add: Display 0 --> Preset Sub: Display Preset -> 0 Seite 22 Inp A: no function Inp B: Start/Stop Add: Display 0 → Preset Sub: Display Preset → 0 FrRrun 15 Input modes: Timing Function Diagram PNP: Count on rising edge NPN: Count on falling edge InA.InB Inp A: Start Inp B: Stop Add: Display 0 --> Preset Sub: Display Preset -> 0 InB.InB Inp A: no function Inp B: Start/Stop Add: Display 0 --> Preset Sub: Display Preset -> 0 FrRrun Inp A: no function Inp B: no function Control of the timing only via the GATE input Add: Display 0 --> Preset Sub: Display Preset -> 0 Auto Inp A: no function Inp B: no function Control of the timing via RESET (manual or electrical) Add: Display 0 --> Preset Sub: Display Preset -> 0 Seite 22 Inp A: no function Inp B: no function Control of the timing only via the GATE input Add: Display 0 → Preset Sub: Display Preset → 0 Auto 15 Input modes: Timing Function Diagram PNP: Count on rising edge NPN: Count on falling edge InA.InB Inp A: Start Inp B: Stop Add: Display 0 --> Preset Sub: Display Preset -> 0 InB.InB Inp A: no function Inp B: Start/Stop Add: Display 0 --> Preset Sub: Display Preset -> 0 FrRrun Inp A: no function Inp B: no function Control of the timing only via the GATE input Add: Display 0 --> Preset Sub: Display Preset -> 0 Auto Inp A: no function Inp B: no function Control of the timing via RESET (manual or electrical) Add: Display 0 --> Preset Sub: Display Preset -> 0 Seite 22 Inp A: no function Inp B: no function Control of the timing via RESET (manual or electrical) Add: Display 0 → Preset Sub: Display Preset → 0 PNP: Count on rising edge NPN: Count on falling edge

42 9.1.3 Frequency meter Function Diagram A 16 Input modes: Frequency meter Function Diagram PNP: Count on rising edge NPN: Count on falling edge A Inp A: Frequency input Inp B: no function AsubB Inp A: Frequency input 1 Inp B: Frequency input 2 Formula: A - B AaddB Inp A: Frequency input 1 Inp B: Frequency input 2 Formula: A + B Quad A 90° B Inp A: Frequency input 1 Inp B: Reverse direction A / B Inp A: Frequency input 1 Inp B: Frequency input 2 Formula: A / B (A-B)/A Inp A: Frequency input 1 Inp B: Frequency input 2 Formula: (A � B)/A x100 english Seite 23 Inp A: Frequency input Inp B: no function AsubB 16 Input modes: Frequency meter Function Diagram PNP: Count on rising edge NPN: Count on falling edge A Inp A: Frequency input Inp B: no function AsubB Inp A: Frequency input 1 Inp B: Frequency input 2 Formula: A - B AaddB Inp A: Frequency input 1 Inp B: Frequency input 2 Formula: A + B Quad A 90° B Inp A: Frequency input 1 Inp B: Reverse direction A / B Inp A: Frequency input 1 Inp B: Frequency input 2 Formula: A / B (A-B)/A Inp A: Frequency input 1 Inp B: Frequency input 2 Formula: (A � B)/A x100 english Seite 23 Inp A: Frequency input 1 Inp B: Frequency input 2 Formula: A-B AaddB 16 Input modes: Frequency meter Function Diagram PNP: Count on rising edge NPN: Count on falling edge A Inp A: Frequency input Inp B: no function AsubB Inp A: Frequency input 1 Inp B: Frequency input 2 Formula: A - B AaddB Inp A: Frequency input 1 Inp B: Frequency input 2 Formula: A + B Quad A 90° B Inp A: Frequency input 1 Inp B: Reverse direction A / B Inp A: Frequency input 1 Inp B: Frequency input 2 Formula: A / B (A-B)/A Inp A: Frequency input 1 Inp B: Frequency input 2 Formula: (A � B)/A x100 english Seite 23 Inp A: Frequency input 1 Inp B: Frequency input 2 Formula: A+B Quad 16 Input modes: Frequency meter Function Diagram PNP: Count on rising edge NPN: Count on falling edge A Inp A: Frequency input Inp B: no function AsubB Inp A: Frequency input 1 Inp B: Frequency input 2 Formula: A - B AaddB Inp A: Frequency input 1 Inp B: Frequency input 2 Formula: A + B Quad A 90° B Inp A: Frequency input 1 Inp B: Reverse direction A / B Inp A: Frequency input 1 Inp B: Frequency input 2 Formula: A / B (A-B)/A Inp A: Frequency input 1 Inp B: Frequency input 2 Formula: (A � B)/A x100 english Seite 23 A 90° B Inp A: Frequency input 1 Inp B: Reverse direction A / B 16 Input modes: Frequency meter Function Diagram PNP: Count on rising edge NPN: Count on falling edge A Inp A: Frequency input Inp B: no function AsubB Inp A: Frequency input 1 Inp B: Frequency input 2 Formula: A - B AaddB Inp A: Frequency input 1 Inp B: Frequency input 2 Formula: A + B Quad A 90° B Inp A: Frequency input 1 Inp B: Reverse direction A / B Inp A: Frequency input 1 Inp B: Frequency input 2 Formula: A / B (A-B)/A Inp A: Frequency input 1 Inp B: Frequency input 2 Formula: (A � B)/A x100 english Seite 23 Inp A: Frequency input 1 Inp B: Frequency input 2 Formula: A/B (A-B)/A 16 Input modes: Frequency meter Function Diagram PNP: Count on rising edge NPN: Count on falling edge A Inp A: Frequency input Inp B: no function AsubB Inp A: Frequency input 1 Inp B: Frequency input 2 Formula: A - B AaddB Inp A: Frequency input 1 Inp B: Frequency input 2 Formula: A + B Quad A 90° B Inp A: Frequency input 1 Inp B: Reverse direction A / B Inp A: Frequency input 1 Inp B: Frequency input 2 Formula: A / B (A-B)/A Inp A: Frequency input 1 Inp B: Frequency input 2 Formula: (A � B)/A x100 english Seite 23 Inp A: Frequency input 1 Inp B: Frequency input 2 Formula: (A-B)/A x100 PNP: Count on rising edge NPN: Count on falling edge

43 9.2 Output operations 9.2.1 Add modes Mode Diagram Add 17 Output operations Mode Diagram Mode Diagram Only in the mode and Additionally in the mode and Add Sub AddAr SubAr AddBat SubBat AddTot SubTot Seite 24 AddAr 17 Output operations Mode Diagram Mode Diagram Only in the mode and Additionally in the mode and Add Sub AddAr SubAr AddBat SubBat AddTot SubTot Seite 24 AddBat 17 Output operations Mode Diagram Mode Diagram Only in the mode and Additionally in the mode and Add Sub AddAr SubAr AddBat SubBat AddTot SubTot Seite 24 AddTot 17 Output operations Mode Diagram Mode Diagram Only in the mode and Additionally in the mode and Add Sub AddAr SubAr AddBat SubBat AddTot SubTot Seite 24 17 Output operations Mode Diagram Mode Diagram Only in the mode and Additionally in the mode and Add Sub only in this modes 17 Output operations Mode Diagram Mode Diagram Only in the mode and Additionally in the mode and Add Sub / 17 Output operations Mode Diagram Mode Diagram Only in the mode and Additionally in the mode and Add Sub Mode Diagram Additionally in the mode and Sub additionally in this modes put operations Diagram Mode Diagram Only in the mode and Additionally in the mode and Sub / t operations gram Mode Diagram Only in the mode and Additionally in the mode and Sub

44 9.2.2 Sub modes Mode Diagram Sub Mode Diagram and Additionally in the mode and Sub SubAr SubBat SubTot SubAr Mode Diagram and Additionally in the mode and Sub SubAr SubBat SubTot SubBat Mode Diagram and Additionally in the mode and Sub SubAr SubBat SubTot SubTot Mode Diagram and Additionally in the mode and Sub SubAr SubBat SubTot 17 Output operations Mode Diagram Mode Diagram Only in the mode and Additionally in the mode and Add Sub only in this modes 17 Output operations Mode Diagram Mode Diagram Only in the mode and Additionally in the mode and Add Sub / 17 Output operations Mode Diagram Mode Diagram Only in the mode and Additionally in the mode and Add Sub Mode Diagram Additionally in the mode and Sub additionally in this modes put operations Diagram Mode Diagram Only in the mode and Additionally in the mode and Sub / t operations gram Mode Diagram Only in the mode and Additionally in the mode and Sub

45 9.2.3 Trail modes Mode Diagram Trail Mode Diagram Trail TrailAr Seite TrailAr Mode Diagram Trail TrailAr Seite

46 10 Dimensions 18 Dimensional Drawings Panel cut-out Seite 26 E89005 18 Dimensional Drawings Panel cut-out Seite 26 Panel cut-out

47 11 Technical data 11.1 General Data Display LCD positive backlite, 2 x 6-digit Digit height Upper line 9 mm Lower line 7 mm Special characters 2 mm Overload Blinking, 1 s Underload Counter loses up to 1 decade, no pulses Data retention > 10 years, EEPROM Operation 8 keys 11.2 Pulse counter Count frequency max� 55 kHz Response time of the relay outputs Add/Sub/Trail < 7 ms With automatic repeat < 7 ms A/B; (A-B)/A < 29 ms Frequencies (typical) 13 Frequencies (typical) 13.1 Pulse counter HTL level AC supply typ. Low 2,5 V typ. High 22 V Add Sub Trail AddAr SubAr AddBat SubBat TrailAr AddTot SubTot Cnt.Dir 55 kHz 2,8 kHz 2,7 kHz Up.Dn Up.Up 29 kHz 2,8 kHz 2,7 kHz Quad Quad 2 28 kHz 1,4 kHz 1,3 kHz Quad 4 18 kHz 1,2 kHz 0,9 kHz A/B (A-B)/A 29 kHz 13.2 Frequency meter HTL level AC supply typ. Low 2,5 V typ. High 22 V HTL 5V A 65 kHz 9 kHz A � B A + B A / B 65 kHz 9 kHz english 11.3 Tacho/Frequency meter Frequency range 0,01 Hz to 65 kHz Measuring principle ≤ 76.3 Hz time interval (period measurement) > 76�3 Hz gate time (gate time approx�13�1 ms) Measuring error < 0�1 % per channel

48 Response time of the relay outputs 1-channel operation < 100 ms @ 40 kHz < 350 ms @ 65 kHz 2-channel operation < 150 ms @ 40 kHz < 600 ms @ 65 kHz Frequencies (typical) Up.Up 29 kHz 2,8 kHz 2,7 kHz Quad Quad 2 28 kHz 1,4 kHz 1,3 kHz Quad 4 18 kHz 1,2 kHz 0,9 kHz A/B (A-B)/A 29 kHz 13.2 Frequency meter HTL level AC supply typ. Low 2,5 V typ. High 22 V HTL 5V A 65 kHz 9 kHz A � B A + B A / B (A-B)/A 65 kHz 9 kHz Quad 30 kHz 9 kHz NOTE: Switching levels of the input Switching levels with AC supply: HTL level Low: 0 .. 4 VDC High: 12 .. 30 VDC english Seite 19 11.4 Timer Seconds 0�001���999 999 s Minutes 0�001���999 999 min Hours 0�001���999 999 h h�min�s 00h�00min�01s���99h�59min�59s Min� time measurable 500 μs Measuring error < 50 ppm Response time of the relay outputs < 7 ms 11.5 Signal and Control inputs Polarity programmable NPN/PNP (for all inputs in common) Input resistance 5 kΩ Pulse shape any Switching level with AC supply HTL level Low 0���4 V DC HTL level High 12���30 V DC Min� pulse length of the reset input 1 ms Min� pulse length of the control inputs 10 ms 11.6 Outputs 11.6.1 Output 1 Type relay with make contact, programmable as NC or NO Switching voltage max� 250 V AC / 110 V DC

49 Switching current max� 3 A AC / DC min� 30 mA DC Switching capacity max� 750 VA / 90 W Mechanical switching cycles 2 x 107 N° of switching cycles 1 x 105 (at 3 A / 250 V AC) N° of switching cycles 1 x 105 (at 3 A / 30 V DC) 11.6.2 Output 2 Type relay with changeover contact Switching voltage max� 250 V AC/ 150 V DC Switching current max� 3 A AC / DC min� 30 mA DC Switching capacity max� 750 VA / 90 W Mechanical switching cycles 2 x 106 N° of switching cycles 5 x 104 (at 3 A / 250 V AC) N° of switching cycles 5 x 104 (at 3 A / 30 V DC) 11.7 Supply voltage Supply voltage 90���260 V AC, max� 8 VA Frequency 50���60 Hz Ext� fuse protection T 0�1 A 11.8 Sensor supply Sensor supply voltage 24 V DC, ± 15% Current 80 mA 11.9 Climatic Conditions Operating temperature -20���65 °C Storage temperature -25���75 °C Relative humidity 93 % at 40 °C, non-condensing Altitude to 2000 m 11.10 EMC Noise immunity EN 61000-6-2 with shielded signal and control cables Noise emission EN 55011 Class B

50 11.11 Device safety Design to EN 61010 Part 1 Protection Class 2 Application area Soiling Level 2 11.12 Mechanical Data Housing panel-mount housing to DIN 43 700, RAL 7021 Dimensions 48 x 48 x 91 mm Panel cut-out 45+0,6 x 45+0,6 mm Installation depth ca� 107 mm incl� terminals Weight ca� 125 g Protection IP 65 (front) Housing material Polycarbonate UL94 V-2 Vibration resistance (EN 60068-2-6) 10���55 Hz / 1 mm / XYZ 30 min in each direction Shock resistance (EN 60068-2-27) 100 g / XYZ 3 times in each directio Cleaning The front of the unit should only be cleaned using a soft damp (water!) cloth� 11.13 Connections Supply voltage and relay outputs Plug-in screw terminal 7-pin, RM 5�08 Core cross section max� 2�5 mm² Signal and control inputs Plug-in screw terminal 8-pin, RM 3�81 Core cross section max� 1�5 mm² 12 Maintenance, repair and disposal The unit is maintenance-free� ► Do not open the housing as the device does not contain any components which can be repaired by the user� The device must only be repaired by the manufacturer� ► Dispose of the device in accordance with the national environmental regulations�

51 13 Approvals/standards The EC declaration of conformity and approvals can be found at: www�ifm�com 14 Attachement Parameter structure (see next pages)

PrES 2 Pr.Out 2 Pr.Out 2 Pr.Out 2 Pr.Out 2 Pr.Out 2 Pr.Out 2 Pr.Out 2 T2 P P P EndPro no EndPro YES T2 P Save Run P T1 T2 T1 R P 1 2 Funct P T2 1 InPut InP.PoL PnP FiLtEr oFF Count Cnt.Dir MPi LAtch Loc.InP PrESET P P P P P InP.PoL nPn T2 FiLtEr on T2 T2 MPi tEAch MPi SEt Loc.InP PrG.PrE Loc.InP ProG T2 T2 P ModE ModE Add P ModE Sub ModE AddAr ModE SubAr ModE AddbAt ModE SubbAt ModE Addtot ModE Subtot ModE trAiL ModE tr_Ar T2 ConFiG P rESmd P rESmd Man.EL rESmd no rES rESmd EL.rEs rESmd MAnrE T2 4 Funct Count Count uP.dn Count uP.uP Count quAd Count quAd 2 Count quAd 4 Count A / B Count A° / b FActor dp 0 CoLor rEd P P P 00.0001 ... 99.9999 T2 dp 0.0 dp 0.00 dp 0.000 T2 CoLor rEdGrn T2 SetPt 000000 P 000000 ... 999999 T2 diViSo P 01.0000 ... 99.9999 T2 ° 3 t.Out 2 00.01 00.00 .. 99.99 T2 T2 4 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 dp 0.0000 dp 0.00000 START Run T2 P ProG no ProG Yes P P R T2 T1 R600318.001 R61318.9416 E89005 E89005

InPut A° / b ° ConFiG P FActor dp 0 StArt 00.0 P P P 00.0001 ... 99.9999 T2 dp 0.0 dp 0.00 dp 0.000 T2 00.0 99.9 T2 AVG oFF P T2 diViSo P 01.0000 ... 99.9999 T2 4 tModE SEC -1 P tModE Min -1 T2 P AVG AVG 2 AVG AVG 5 AVG AVG 10 AVG AVG 20 P WAit0 00.1 00.1 99.0 T2 P CoLor rEd CoLor rEdGrn P 2 Funct timEr InPut InP.PoL PnP FiLtEr oFF StArt InA.Inb GAtE GAtE.Lo MPi LAtch Loc.InP PrESET P P P P P InP.PoL nPn T2 FiLtEr on T2 StArt Inb.Inb StArt FrErun StArt Auto T2 GAtE GAtE.hi T2 MPi tEAch MPi SEt Loc.InP PrG.PrE Loc.InP ProG T2 T2 P ModE ModE Add P ModE Sub ModE AddAr ModE SubAr ModE AddbAt ModE SubbAt ModE Addtot ModE Subtot ModE trAiL ModE tr_Ar T2 ConFiG tModE SEC dp 0 CoLor rEd P P P P tModE Min tModE hour tModE h.Min.S T2 dp 0.0 dp 0.00 dp 0.000 T2 CoLor rEdGrn T2 rESmd P rESmd Man.EL rESmd no rES rESmd EL.rEs rESmd MAnrE T2 4 T2 T1 SetPt 000000 P 000000 ... 999999 T2 T2 T2 T1 T2 T1 T2 T1 P R600318.001 R61318.9416 ifm weltweit - ifm worldwide - ifm à l’échelle internationale http://www.ifm.com e-mail: [email protected] Service-Hotline: 0800 16 16 16 4 (nur Deutschland, Mo-Fr von 7.00-18.00 Uhr) i ifm electronic gmbh • 1120 Wien • Tel. +43 16 17 45 00 A +60 7 / 331 5022 M