iDataLink Maestro AR Install Manual

are the properties of their respective owners. WARNING Pressing the printer icon or “quick printing” this document will print all of the guides in this compilation. Open the Bookmarks menu and find your vehicle OR scroll down until you find the install guide for your vehicle. Print only the pages for your vehicle using the advanced options in the Print menu. Install your Maestro AR according to the guide for your vehicle. HOW TO USE THIS INSTALL GUIDE 1 2 3 SELECT VEHICLE PRINT PAGES NEEDED

Kenwood amplifier PROGRAMMED FIRMWARE ADS-AR-CHR02 PRODUCTS REQUIRED iDatalink Maestro AR Amplifier Replacement Interface iDatalink Maestro AR-CH2 Installation Harness INSTALL GUIDE CHRySLER 200 2015-2016 ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION, WITHOUT CHANGING YOUR RADIO. NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

Automotive Data Solutions Inc. © 2017 2 WELCOME NEED HELP? Congratulations on the purchase of your iDatalink Maestro AR Amplifi er replacement solution. You are now a few simple steps away from enjoying your new car amplifi er. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide. 1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum TABLE OF CONTENTS Settings and Features 3 Installation Instructions 4 Wiring Diagram 5 Vehicle Wire Reference Chart 6

Automotive Data Solutions Inc. © 2017 3 SETTINGS AND FEATURES CHIME ADJUSTMENT This is only needed when the vehicle supports chimes (ex: Parking assist, Blind spot detection, Lane sense, etc.). • Set the audio source to OFF. If there is no way to turn the radio OFF, set the source to AUX. • The OEM radio will have 3 volume settings for parking assist (Low/Med/High), it is recommended to choose Medium volume. • Activate any chime (ex: rear parking assist). • Adjust the chime volume using the volume knob. MAESTRO AR PROGRAMMABLE FEATURES These tone control features can be adjusted in the settings of the radio. • Bass Tone Control Subwoofer Volume • Mid Tone Control Not applicable • Treble Tone Control Tweeter Output Gain • Surround Control Not applicable • Speed Compensated Volume None 1

Automotive Data Solutions Inc. © 2017 4 INSTALLATION INSTRUCTIONS STEP 1 • Remove the factory amplifi er (refer to wire chart for amplifi er location). • Confi gure the 2 pin connectors on the AR-CH2 T-harness as shown on the wiring diagram. STEP 2 • Connect the factory amplifi er harnesses to the AR-CH2 T-harness. STEP 3 • Connect the wires from the AR-CH2 T-harness to the aftermarket amplifi er. Note 1: If you are running your own speaker wires from the amplifi er to the speakers, this step is not necessary. Note 2: The amplifi er output colors and labels on the CH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, see the wiring chart. • Plug the connector from the AR-CH2 T-Harness into the aftermarket amplifi er. • Plug the Data cable to the data port of the aftermarket amplifi er. STEP 4 • Connect all the harnesses to the Maestro AR module. • For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink. com/support” and “www.12voltdata.com/forum/” 1

Automotive Data Solutions Inc. © 2017 5 AMP TURN ON A B C B C 1 LEFT FRONT 1 RIGHT FRONT 1 LEFT REAR 1 RIGHT REAR 1 LEFT FRONT 2 RIGHT FRONT 2 LEFT REAR 2 RIGHT REAR 2 SUB 1 SUB 2 SUB 3 CENTER 1 A A STEP 1 STEP 2 STEP 3 STEP 4 MAESTRO AR MODULE MAESTRO AR MODULE DATA CABLE AR-CH2 T-HARNESS AR-CH2 T-HARNESS FACTORY AMPLIFIER HARNESSES KENWOOD AMPLIFIER KENWOOD AMPLIFLIER WIRES FROM VEHICLE WHITE (1) WHITE GREEN GREEN GRAY 18 PIN CONNECTOR GRAY BLUE PURPLE PURPLE RED WHITE (2) N.C. WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE/BLACK GRAY/RED WHITE/RED GRAY GREEN GREEN/RED PURPLE WHITE PURPLE PURPLE/RED BLACK BLACK/WHITE BLACK BLACK/RED BLACK BLACK/YELLOW ORANGE ORANGE/BLACK (1) NOTE: WHITE 2-PIN CONNECTOR IS ONLY NECESSARY IF THE VEHICLE HAS CHIMES. (2) NOTE: IF AN EXTENSION HARNESS IS BEING USED: - DO NOT CONNECT THE (2) WHITE 2-PIN ADAPTER TO THE PURPLE 2-PIN CONNECTOR. - CUT OFF THE WHITE 2-PIN CONNECTOR FROM THE ADAPTER CABLE. - CONNECT THE WHITE WIRE FROM ADAPTER TO RED WIRE (PIN 15) OF 18-PIN CONNECTOR. - CONNECT THE BLACK WIRE FROM ADAPTER TO RED/BLACK WIRE (PIN 6) OF 18-PIN CONNECTOR. - CONNECT THE OTHER SIDE OF ADAPTER TO MAESTRO AR MODULE (POSITION A). CONNECTION NOT REQUIRED SECOND AMP 18 PIN CONNECTOR N.C. CONNECT THE BLUE WIRE (PIN 16) TO SECOND AMPLIFIER (IF PRESENT) (TO TURN IT ON) WIRING DIAGRAM

Automotive Data Solutions Inc. © 2017 6 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 1 2 5 6 8 9 12 13 16 VEHICLE WIRE REFERENCE CHART T-Harness Wires Vehicle Wires Wire Tag Wire Color Speaker Wire Description Component Position LEFT FRONT 1 White Left Front Mid (+) 1 White/Black Left Front Mid (-) LEFT FRONT 2 White Left Front Tweeter (+) 5 White/Red Left Front Tweeter (-) RIGHT FRONT 1 Gray Right Front Mid (+) 2 Gray/Black Right Front Mid (-) RIGHT FRONT 2 Gray Right Front Tweeter (+) 6 Gray/Red Right Front Tweeter (-) LEFT REAR 1 Green Left Rear Mid (+) 12 Green/Black Left Rear Mid (-) LEFT REAR 2 Green Subwoofer 1 (+) 16 Green/Red Subwoofer 1 (-) RIGHT REAR 1 Purple Right Rear Mid (+) 13 Purple/Black Right Rear Mid (-) RIGHT REAR 2 Purple Subwoofer 2 (+) 16 Purple/Red Subwoofer 2 (-) CENTER 1 Orange Left Rear Tweeter (+) 8 Orange/Black Left Rear Tweeter (-) SUB 1 Black n/a Black/White n/a SUB 2 Black Right Rear Tweeter (+) 9 Black/Red Right Rear Tweeter (-) SUB 3 Black n/a Black/Yellow n/a Amplifi er location: Right end of dash Note: The amplifi er output colors and labels on the AR-CH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, follow this wiring chart.

Fonctionne-t-it avec mon auto? i,Funciona con mi coche?

Kenwood amplifier PROGRAMMED FIRMWARE ADS-AR-CHR02 PRODUCTS REQUIRED iDatalink Maestro AR Amplifier Replacement Interface iDatalink Maestro AR-CH2 Installation Harness INSTALL GUIDE CHRySLER 300 2012-2014 ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION, WITHOUT CHANGING YOUR RADIO. NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

Automotive Data Solutions Inc. © 2017 2 WELCOME NEED HELP? Congratulations on the purchase of your iDatalink Maestro AR Amplifi er replacement solution. You are now a few simple steps away from enjoying your new car amplifi er. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide. 1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum TABLE OF CONTENTS Settings and Features 3 Installation Instructions 4 Wiring Diagram 5 Vehicle Wire Reference Chart 6

Automotive Data Solutions Inc. © 2017 3 SETTINGS AND FEATURES CHIME ADJUSTMENT This is only needed when the vehicle supports chimes (ex: Parking assist, Blind spot detection, Lane sense, etc.). • Set the audio source to OFF. If there is no way to turn the radio OFF, set the source to AUX. • The OEM radio will have 3 volume settings for parking assist (Low/Med/High), it is recommended to choose Medium volume. • Activate any chime (ex: rear parking assist). • Adjust the chime volume using the volume knob. MAESTRO AR PROGRAMMABLE FEATURES These tone control features can be adjusted in the settings of the radio. • Bass Tone Control Subwoofer Volume • Mid Tone Control Not applicable • Treble Tone Control Tweeter Output Gain • Surround Control Not applicable • Speed Compensated Volume None 2

Automotive Data Solutions Inc. © 2017 4 INSTALLATION INSTRUCTIONS STEP 1 • Remove the factory amplifi er (refer to wire chart for amplifi er location). • Confi gure the 2 pin connectors on the AR-CH2 T-harness as shown on the wiring diagram. STEP 2 • Connect the factory amplifi er harnesses to the AR-CH2 T-harness. STEP 3 • Connect the wires from the AR-CH2 T-harness to the aftermarket amplifi er. Note 1: If you are running your own speaker wires from the amplifi er to the speakers, this step is not necessary. Note 2: The amplifi er output colors and labels on the CH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, see the wiring chart. • Plug the connector from the AR-CH2 T-Harness into the aftermarket amplifi er. • Plug the Data cable to the data port of the aftermarket amplifi er. STEP 4 • Connect all the harnesses to the Maestro AR module. • For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink. com/support” and “www.12voltdata.com/forum/” 2

Automotive Data Solutions Inc. © 2017 5 AMP TURN ON B C B C 2 LEFT FRONT 1 RIGHT FRONT 1 LEFT REAR 1 RIGHT REAR 1 LEFT FRONT 2 RIGHT FRONT 2 LEFT REAR 2 RIGHT REAR 2 SUB 1 SUB 2 SUB 3 CENTER 1 STEP 1 STEP 2 STEP 3 STEP 4 MAESTRO AR MODULE DATA CABLE AR-CH2 T-HARNESS FACTORY AMPLIFIER HARNESSES KENWOOD AMPLIFIER WIRES FROM VEHICLE WHITE WHITE GREEN GREEN GRAY GRAY BLUE PURPLE PURPLE RED N.C. N.C. WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE/BLACK GRAY/RED WHITE/RED GRAY GREEN GREEN/RED PURPLE WHITE PURPLE PURPLE/RED BLACK BLACK/WHITE BLACK BLACK/RED BLACK BLACK/YELLOW ORANGE ORANGE/BLACK CONNECTIONS NOT REQUIRED SECOND AMP 18 PIN CONNECTOR N.C. CONNECT THE BLUE WIRE (PIN 16) TO SECOND AMPLIFIER (IF PRESENT) (TO TURN IT ON) WIRING DIAGRAM

Automotive Data Solutions Inc. © 2017 6 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 1 2 5 6 7 8 9 12 13 16 17 VEHICLE WIRE REFERENCE CHART T-Harness Wires Vehicle Wires Wire Tag Wire Color Speaker Wire Description Component Position LEFT FRONT 1 White Left Front Speaker (+) 1 White/Black Left Front Speaker (-) LEFT FRONT 2 White Left Front Tweeter (+) 5 White/Red Left Front Tweeter (-) RIGHT FRONT 1 Gray Right Front Speaker (+) 2 Gray/Black Right Front Speaker (-) RIGHT FRONT 2 Gray Right Front Tweeter (+) 6 Gray/Red Right Front Tweeter (-) LEFT REAR 1 Green Left Rear Speaker (+) 8 Green/Black Left Rear Speaker (-) LEFT REAR 2 Green Left Rear Tweeter (+) 12 Green/Red Left Rear Tweeter (-) RIGHT REAR 1 Purple Right Rear Speaker (+) 9 Purple/Black Right Rear Speaker (-) RIGHT REAR 2 Purple Right Rear Tweeter (+) 13 Purple/Red Right Rear Tweeter (-) CENTER 1 Orange Center Speaker (+) 7 Orange/Black Center Speaker (-) SUB 1 Black Subwoofer 1 (+) 17 Black/White Subwoofer 1 (-) SUB 2 Black Subwoofer 2 (+) 17 Black/Red Subwoofer 2 (-) SUB 3 Black Subwoofer 3 (+) 16 Black/Yellow Subwoofer 3 (-) Amplifi er location: Left end of dash Note: The amplifi er output colors and labels on the AR-CH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, follow this wiring chart.

Kenwood amplifier PROGRAMMED FIRMWARE ADS-AR-CHR02 PRODUCTS REQUIRED iDatalink Maestro AR Amplifier Replacement Interface iDatalink Maestro AR-CH2 Installation Harness INSTALL GUIDE CHRySLER 300 2015-2016 ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION, WITHOUT CHANGING YOUR RADIO. NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

Automotive Data Solutions Inc. © 2017 2 WELCOME NEED HELP? Congratulations on the purchase of your iDatalink Maestro AR Amplifi er replacement solution. You are now a few simple steps away from enjoying your new car amplifi er. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide. 1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum TABLE OF CONTENTS Settings and Features 3 Installation Instructions 4 Wiring Diagram 5 Vehicle Wire Reference Chart 6

Automotive Data Solutions Inc. © 2017 3 SETTINGS AND FEATURES CHIME ADJUSTMENT This is only needed when the vehicle supports chimes (ex: Parking assist, Blind spot detection, Lane sense, etc.). • Set the audio source to OFF. If there is no way to turn the radio OFF, set the source to AUX. • The OEM radio will have 3 volume settings for parking assist (Low/Med/High), it is recommended to choose Medium volume. • Activate any chime (ex: rear parking assist). • Adjust the chime volume using the volume knob. MAESTRO AR PROGRAMMABLE FEATURES These tone control features can be adjusted in the settings of the radio. • Bass Tone Control Subwoofer Volume • Mid Tone Control Not applicable • Treble Tone Control Tweeter Output Gain • Surround Control Not applicable • Speed Compensated Volume None 1

Automotive Data Solutions Inc. © 2017 4 INSTALLATION INSTRUCTIONS STEP 1 • Remove the factory amplifi er (refer to wire chart for amplifi er location). • Confi gure the 2 pin connectors on the AR-CH2 T-harness as shown on the wiring diagram. STEP 2 • Connect the factory amplifi er harnesses to the AR-CH2 T-harness. STEP 3 • Connect the wires from the AR-CH2 T-harness to the aftermarket amplifi er. Note 1: If you are running your own speaker wires from the amplifi er to the speakers, this step is not necessary. Note 2: The amplifi er output colors and labels on the CH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, see the wiring chart. • Plug the connector from the AR-CH2 T-Harness into the aftermarket amplifi er. • Plug the Data cable to the data port of the aftermarket amplifi er. STEP 4 • Connect all the harnesses to the Maestro AR module. • For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink. com/support” and “www.12voltdata.com/forum/” 1

Automotive Data Solutions Inc. © 2017 5 AMP TURN ON A B C B C 1 LEFT FRONT 1 RIGHT FRONT 1 LEFT REAR 1 RIGHT REAR 1 LEFT FRONT 2 RIGHT FRONT 2 LEFT REAR 2 RIGHT REAR 2 SUB 1 SUB 2 SUB 3 CENTER 1 A A STEP 1 STEP 2 STEP 3 STEP 4 MAESTRO AR MODULE MAESTRO AR MODULE DATA CABLE AR-CH2 T-HARNESS AR-CH2 T-HARNESS FACTORY AMPLIFIER HARNESSES KENWOOD AMPLIFIER KENWOOD AMPLIFLIER WIRES FROM VEHICLE WHITE (1) WHITE GREEN GREEN GRAY 18 PIN CONNECTOR GRAY BLUE PURPLE PURPLE RED WHITE (2) N.C. WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE/BLACK GRAY/RED WHITE/RED GRAY GREEN GREEN/RED PURPLE WHITE PURPLE PURPLE/RED BLACK BLACK/WHITE BLACK BLACK/RED BLACK BLACK/YELLOW ORANGE ORANGE/BLACK (1) NOTE: WHITE 2-PIN CONNECTOR IS ONLY NECESSARY IF THE VEHICLE HAS CHIMES. (2) NOTE: IF AN EXTENSION HARNESS IS BEING USED: - DO NOT CONNECT THE (2) WHITE 2-PIN ADAPTER TO THE PURPLE 2-PIN CONNECTOR. - CUT OFF THE WHITE 2-PIN CONNECTOR FROM THE ADAPTER CABLE. - CONNECT THE WHITE WIRE FROM ADAPTER TO RED WIRE (PIN 15) OF 18-PIN CONNECTOR. - CONNECT THE BLACK WIRE FROM ADAPTER TO RED/BLACK WIRE (PIN 6) OF 18-PIN CONNECTOR. - CONNECT THE OTHER SIDE OF ADAPTER TO MAESTRO AR MODULE (POSITION A). CONNECTION NOT REQUIRED SECOND AMP 18 PIN CONNECTOR N.C. CONNECT THE BLUE WIRE (PIN 16) TO SECOND AMPLIFIER (IF PRESENT) (TO TURN IT ON) WIRING DIAGRAM

Automotive Data Solutions Inc. © 2017 6 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 1 2 5 6 7 8 9 12 13 16 17 VEHICLE WIRE REFERENCE CHART T-Harness Wires Vehicle Wires Wire Tag Wire Color Speaker Wire Description Component Position LEFT FRONT 1 White Left Front Speaker (+) 1 White/Black Left Front Speaker (-) LEFT FRONT 2 White Left Front Tweeter (+) 5 White/Red Left Front Tweeter (-) RIGHT FRONT 1 Gray Right Front Speaker (+) 2 Gray/Black Right Front Speaker (-) RIGHT FRONT 2 Gray Right Front Tweeter (+) 6 Gray/Red Right Front Tweeter (-) LEFT REAR 1 Green Left Rear Speaker (+) 8 Green/Black Left Rear Speaker (-) LEFT REAR 2 Green Left Rear Tweeter (+) 12 Green/Red Left Rear Tweeter (-) RIGHT REAR 1 Purple Right Rear Speaker (+) 9 Purple/Black Right Rear Speaker (-) RIGHT REAR 2 Purple Right Rear Tweeter (+) 13 Purple/Red Right Rear Tweeter (-) CENTER 1 Orange Center Speaker (+) 7 Orange/Black Center Speaker (-) SUB 1 Black Subwoofer 1 (+) 17 Black/White Subwoofer 1 (-) SUB 2 Black Subwoofer 2 (+) 17 Black/Red Subwoofer 2 (-) SUB 3 Black Subwoofer 3 (+) 16 Black/Yellow Subwoofer 3 (-) Amplifi er location: Left end of dash Note: The amplifi er output colors and labels on the AR-CH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, follow this wiring chart.

Kenwood amplifier PROGRAMMED FIRMWARE ADS-AR-CHR02 PRODUCTS REQUIRED iDatalink Maestro AR Amplifier Replacement Interface iDatalink Maestro AR-CH2 Installation Harness INSTALL GUIDE DODGE CHALLENGER 2015-2017 ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION, WITHOUT CHANGING YOUR RADIO. NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

Automotive Data Solutions Inc. © 2017 2 WELCOME NEED HELP? Congratulations on the purchase of your iDatalink Maestro AR Amplifi er replacement solution. You are now a few simple steps away from enjoying your new car amplifi er. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide. 1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum TABLE OF CONTENTS Settings and Features 3 Installation Instructions 4 Wiring Diagram 5 Vehicle Wire Reference Chart 6

Automotive Data Solutions Inc. © 2017 3 SETTINGS AND FEATURES CHIME ADJUSTMENT This is only needed when the vehicle supports chimes (ex: Parking assist, Blind spot detection, Lane sense, etc.). • Set the audio source to OFF. If there is no way to turn the radio OFF, set the source to AUX. • The OEM radio will have 3 volume settings for parking assist (Low/Med/High), it is recommended to choose Medium volume. • Activate any chime (ex: rear parking assist). • Adjust the chime volume using the volume knob. MAESTRO AR PROGRAMMABLE FEATURES These tone control features can be adjusted in the settings of the radio. • Bass Tone Control Subwoofer Volume • Mid Tone Control Not applicable • Treble Tone Control Tweeter Output Gain • Surround Control Not applicable • Speed Compensated Volume None 1

Automotive Data Solutions Inc. © 2017 4 INSTALLATION INSTRUCTIONS STEP 1 • Remove the factory amplifi er (refer to wire chart for amplifi er location). • Confi gure the 2 pin connectors on the AR-CH2 T-harness as shown on the wiring diagram. STEP 2 • Connect the factory amplifi er harnesses to the AR-CH2 T-harness. STEP 3 • Connect the wires from the AR-CH2 T-harness to the aftermarket amplifi er. Note 1: If you are running your own speaker wires from the amplifi er to the speakers, this step is not necessary. Note 2: The amplifi er output colors and labels on the CH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, see the wiring chart. • Plug the connector from the AR-CH2 T-Harness into the aftermarket amplifi er. • Plug the Data cable to the data port of the aftermarket amplifi er. STEP 4 • Connect all the harnesses to the Maestro AR module. • For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink. com/support” and “www.12voltdata.com/forum/” 1

Automotive Data Solutions Inc. © 2017 5 AMP TURN ON A B C B C 1 LEFT FRONT 1 RIGHT FRONT 1 LEFT REAR 1 RIGHT REAR 1 LEFT FRONT 2 RIGHT FRONT 2 LEFT REAR 2 RIGHT REAR 2 SUB 1 SUB 2 SUB 3 CENTER 1 A A STEP 1 STEP 2 STEP 3 STEP 4 MAESTRO AR MODULE MAESTRO AR MODULE DATA CABLE AR-CH2 T-HARNESS AR-CH2 T-HARNESS FACTORY AMPLIFIER HARNESSES KENWOOD AMPLIFIER KENWOOD AMPLIFLIER WIRES FROM VEHICLE WHITE (1) WHITE GREEN GREEN GRAY 18 PIN CONNECTOR GRAY BLUE PURPLE PURPLE RED WHITE (2) N.C. WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE/BLACK GRAY/RED WHITE/RED GRAY GREEN GREEN/RED PURPLE WHITE PURPLE PURPLE/RED BLACK BLACK/WHITE BLACK BLACK/RED BLACK BLACK/YELLOW ORANGE ORANGE/BLACK (1) NOTE: WHITE 2-PIN CONNECTOR IS ONLY NECESSARY IF THE VEHICLE HAS CHIMES. (2) NOTE: IF AN EXTENSION HARNESS IS BEING USED: - DO NOT CONNECT THE (2) WHITE 2-PIN ADAPTER TO THE PURPLE 2-PIN CONNECTOR. - CUT OFF THE WHITE 2-PIN CONNECTOR FROM THE ADAPTER CABLE. - CONNECT THE WHITE WIRE FROM ADAPTER TO RED WIRE (PIN 15) OF 18-PIN CONNECTOR. - CONNECT THE BLACK WIRE FROM ADAPTER TO RED/BLACK WIRE (PIN 6) OF 18-PIN CONNECTOR. - CONNECT THE OTHER SIDE OF ADAPTER TO MAESTRO AR MODULE (POSITION A). CONNECTION NOT REQUIRED SECOND AMP 18 PIN CONNECTOR N.C. CONNECT THE BLUE WIRE (PIN 16) TO SECOND AMPLIFIER (IF PRESENT) (TO TURN IT ON) WIRING DIAGRAM

Automotive Data Solutions Inc. © 2017 6 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 1 2 5 6 7 8 9 12 13 16 VEHICLE WIRE REFERENCE CHART T-Harness Wires Vehicle Wires Wire Tag Wire Color Speaker Wire Description Component Position LEFT FRONT 1 White Left Front Speaker (+) 1 White/Black Left Front Speaker (-) LEFT FRONT 2 White Left Front Tweeter (+) 5 White/Red Left Front Tweeter (-) RIGHT FRONT 1 Gray Right Front Speaker (+) 2 Gray/Black Right Front Speaker (-) RIGHT FRONT 2 Gray Right Front Tweeter (+) 6 Gray/Red Right Front Tweeter (-) LEFT REAR 1 Green Left Rear Speaker (+) 8 Green/Black Left Rear Speaker (-) LEFT REAR 2 Green Left Rear Mid (+) 12 Green/Red Left Rear Mid (-) RIGHT REAR 1 Purple Right Rear Speaker (+) 9 Purple/Black Right Rear Speaker (-) RIGHT REAR 2 Purple Right Rear Mid (+) 13 Purple/Red Right Rear Mid (-) CENTER 1 Orange Center Speaker (+) 7 Orange/Black Center Speaker (-) SUB 1 Black Subwoofer 1 (+) 16 Black/White Subwoofer 1 (-) SUB 2 Black Subwoofer 2 (+) 16 Black/Red Subwoofer 2 (-) SUB 3 Black n/a Black/Yellow n/a Amplifi er location: Left end of dash Note: The amplifi er output colors and labels on the AR-CH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, follow this wiring chart.

Kenwood amplifier PROGRAMMED FIRMWARE ADS-AR-CHR02 PRODUCTS REQUIRED iDatalink Maestro AR Amplifier Replacement Interface iDatalink Maestro AR-CH2 Installation Harness INSTALL GUIDE DODGE CHARGER 2012-2014 ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION, WITHOUT CHANGING YOUR RADIO. NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

Automotive Data Solutions Inc. © 2017 2 WELCOME NEED HELP? Congratulations on the purchase of your iDatalink Maestro AR Amplifi er replacement solution. You are now a few simple steps away from enjoying your new car amplifi er. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide. 1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum TABLE OF CONTENTS Settings and Features 3 Installation Instructions 4 Wiring Diagram 5 Vehicle Wire Reference Chart 6

Automotive Data Solutions Inc. © 2017 3 SETTINGS AND FEATURES CHIME ADJUSTMENT This is only needed when the vehicle supports chimes (ex: Parking assist, Blind spot detection, Lane sense, etc.). • Set the audio source to OFF. If there is no way to turn the radio OFF, set the source to AUX. • The OEM radio will have 3 volume settings for parking assist (Low/Med/High), it is recommended to choose Medium volume. • Activate any chime (ex: rear parking assist). • Adjust the chime volume using the volume knob. MAESTRO AR PROGRAMMABLE FEATURES These tone control features can be adjusted in the settings of the radio. • Bass Tone Control Subwoofer Volume • Mid Tone Control Not applicable • Treble Tone Control Tweeter Output Gain • Surround Control Not applicable • Speed Compensated Volume None 2

Automotive Data Solutions Inc. © 2017 4 INSTALLATION INSTRUCTIONS STEP 1 • Remove the factory amplifi er (refer to wire chart for amplifi er location). • Confi gure the 2 pin connectors on the AR-CH2 T-harness as shown on the wiring diagram. STEP 2 • Connect the factory amplifi er harnesses to the AR-CH2 T-harness. STEP 3 • Connect the wires from the AR-CH2 T-harness to the aftermarket amplifi er. Note 1: If you are running your own speaker wires from the amplifi er to the speakers, this step is not necessary. Note 2: The amplifi er output colors and labels on the CH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, see the wiring chart. • Plug the connector from the AR-CH2 T-Harness into the aftermarket amplifi er. • Plug the Data cable to the data port of the aftermarket amplifi er. STEP 4 • Connect all the harnesses to the Maestro AR module. • For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink. com/support” and “www.12voltdata.com/forum/” 2

Automotive Data Solutions Inc. © 2017 5 AMP TURN ON B C B C 2 LEFT FRONT 1 RIGHT FRONT 1 LEFT REAR 1 RIGHT REAR 1 LEFT FRONT 2 RIGHT FRONT 2 LEFT REAR 2 RIGHT REAR 2 SUB 1 SUB 2 SUB 3 CENTER 1 STEP 1 STEP 2 STEP 3 STEP 4 MAESTRO AR MODULE DATA CABLE AR-CH2 T-HARNESS FACTORY AMPLIFIER HARNESSES KENWOOD AMPLIFIER WIRES FROM VEHICLE WHITE WHITE GREEN GREEN GRAY GRAY BLUE PURPLE PURPLE RED N.C. N.C. WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE/BLACK GRAY/RED WHITE/RED GRAY GREEN GREEN/RED PURPLE WHITE PURPLE PURPLE/RED BLACK BLACK/WHITE BLACK BLACK/RED BLACK BLACK/YELLOW ORANGE ORANGE/BLACK CONNECTIONS NOT REQUIRED SECOND AMP 18 PIN CONNECTOR N.C. CONNECT THE BLUE WIRE (PIN 16) TO SECOND AMPLIFIER (IF PRESENT) (TO TURN IT ON) WIRING DIAGRAM

Automotive Data Solutions Inc. © 2017 6 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 1 2 5 6 7 8 9 12 13 16 17 VEHICLE WIRE REFERENCE CHART T-Harness Wires Vehicle Wires Wire Tag Wire Color Speaker Wire Description Component Position LEFT FRONT 1 White Left Front Speaker (+) 1 White/Black Left Front Speaker (-) LEFT FRONT 2 White Left Front Tweeter (+) 5 White/Red Left Front Tweeter (-) RIGHT FRONT 1 Gray Right Front Speaker (+) 2 Gray/Black Right Front Speaker (-) RIGHT FRONT 2 Gray Right Front Tweeter (+) 6 Gray/Red Right Front Tweeter (-) LEFT REAR 1 Green Left Rear Speaker (+) 8 Green/Black Left Rear Speaker (-) LEFT REAR 2 Green Left Rear Speaker (+) 12 Green/Red Left Rear Speaker (-) RIGHT REAR 1 Purple Right Rear Speaker (+) 9 Purple/Black Right Rear Speaker (-) RIGHT REAR 2 Purple Right Rear Speaker (+) 13 Purple/Red Right Rear Speaker (-) CENTER 1 Orange Center Speaker (+) 7 Orange/Black Center Speaker (-) SUB 1 Black Subwoofer 1 (+) 17 Black/White Subwoofer 1 (-) SUB 2 Black Subwoofer 2 (+) 17 Black/Red Subwoofer 2 (-) SUB 3 Black Subwoofer 3 (+) 16 Black/Yellow Subwoofer 3 (-) Amplifi er location: Left side of dash Note: The amplifi er output colors and labels on the AR-CH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, follow this wiring chart.

Kenwood amplifier PROGRAMMED FIRMWARE ADS-AR-CHR02 PRODUCTS REQUIRED iDatalink Maestro AR Amplifier Replacement Interface iDatalink Maestro AR-CH2 Installation Harness INSTALL GUIDE DODGE CHARGER 2015-2017 ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION, WITHOUT CHANGING YOUR RADIO. NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

Automotive Data Solutions Inc. © 2017 2 WELCOME NEED HELP? Congratulations on the purchase of your iDatalink Maestro AR Amplifi er replacement solution. You are now a few simple steps away from enjoying your new car amplifi er. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide. 1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum TABLE OF CONTENTS Settings and Features 3 Installation Instructions 4 Wiring Diagram 5 Vehicle Wire Reference Chart 6

Automotive Data Solutions Inc. © 2017 3 SETTINGS AND FEATURES CHIME ADJUSTMENT This is only needed when the vehicle supports chimes (ex: Parking assist, Blind spot detection, Lane sense, etc.). • Set the audio source to OFF. If there is no way to turn the radio OFF, set the source to AUX. • The OEM radio will have 3 volume settings for parking assist (Low/Med/High), it is recommended to choose Medium volume. • Activate any chime (ex: rear parking assist). • Adjust the chime volume using the volume knob. MAESTRO AR PROGRAMMABLE FEATURES These tone control features can be adjusted in the settings of the radio. • Bass Tone Control Subwoofer Volume • Mid Tone Control Not applicable • Treble Tone Control Tweeter Output Gain • Surround Control Not applicable • Speed Compensated Volume None 1

Automotive Data Solutions Inc. © 2017 4 INSTALLATION INSTRUCTIONS STEP 1 • Remove the factory amplifi er (refer to wire chart for amplifi er location). • Confi gure the 2 pin connectors on the AR-CH2 T-harness as shown on the wiring diagram. STEP 2 • Connect the factory amplifi er harnesses to the AR-CH2 T-harness. STEP 3 • Connect the wires from the AR-CH2 T-harness to the aftermarket amplifi er. Note 1: If you are running your own speaker wires from the amplifi er to the speakers, this step is not necessary. Note 2: The amplifi er output colors and labels on the CH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, see the wiring chart. • Plug the connector from the AR-CH2 T-Harness into the aftermarket amplifi er. • Plug the Data cable to the data port of the aftermarket amplifi er. STEP 4 • Connect all the harnesses to the Maestro AR module. • For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink. com/support” and “www.12voltdata.com/forum/” 1

Automotive Data Solutions Inc. © 2017 5 AMP TURN ON A B C B C 1 LEFT FRONT 1 RIGHT FRONT 1 LEFT REAR 1 RIGHT REAR 1 LEFT FRONT 2 RIGHT FRONT 2 LEFT REAR 2 RIGHT REAR 2 SUB 1 SUB 2 SUB 3 CENTER 1 A A STEP 1 STEP 2 STEP 3 STEP 4 MAESTRO AR MODULE MAESTRO AR MODULE DATA CABLE AR-CH2 T-HARNESS AR-CH2 T-HARNESS FACTORY AMPLIFIER HARNESSES KENWOOD AMPLIFIER KENWOOD AMPLIFLIER WIRES FROM VEHICLE WHITE (1) WHITE GREEN GREEN GRAY 18 PIN CONNECTOR GRAY BLUE PURPLE PURPLE RED WHITE (2) N.C. WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE/BLACK GRAY/RED WHITE/RED GRAY GREEN GREEN/RED PURPLE WHITE PURPLE PURPLE/RED BLACK BLACK/WHITE BLACK BLACK/RED BLACK BLACK/YELLOW ORANGE ORANGE/BLACK (1) NOTE: WHITE 2-PIN CONNECTOR IS ONLY NECESSARY IF THE VEHICLE HAS CHIMES. (2) NOTE: IF AN EXTENSION HARNESS IS BEING USED: - DO NOT CONNECT THE (2) WHITE 2-PIN ADAPTER TO THE PURPLE 2-PIN CONNECTOR. - CUT OFF THE WHITE 2-PIN CONNECTOR FROM THE ADAPTER CABLE. - CONNECT THE WHITE WIRE FROM ADAPTER TO RED WIRE (PIN 15) OF 18-PIN CONNECTOR. - CONNECT THE BLACK WIRE FROM ADAPTER TO RED/BLACK WIRE (PIN 6) OF 18-PIN CONNECTOR. - CONNECT THE OTHER SIDE OF ADAPTER TO MAESTRO AR MODULE (POSITION A). CONNECTION NOT REQUIRED SECOND AMP 18 PIN CONNECTOR N.C. CONNECT THE BLUE WIRE (PIN 16) TO SECOND AMPLIFIER (IF PRESENT) (TO TURN IT ON) WIRING DIAGRAM

Automotive Data Solutions Inc. © 2017 6 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 1 2 5 6 7 8 9 12 13 16 17 VEHICLE WIRE REFERENCE CHART T-Harness Wires Vehicle Wires Wire Tag Wire Color Speaker Wire Description Component Position LEFT FRONT 1 White Left Front Speaker (+) 1 White/Black Left Front Speaker (-) LEFT FRONT 2 White Left Front Tweeter (+) 5 White/Red Left Front Tweeter (-) RIGHT FRONT 1 Gray Right Front Speaker (+) 2 Gray/Black Right Front Speaker (-) RIGHT FRONT 2 Gray Right Front Tweeter (+) 6 Gray/Red Right Front Tweeter (-) LEFT REAR 1 Green Left Rear Speaker (+) 8 Green/Black Left Rear Speaker (-) LEFT REAR 2 Green Left Rear Speaker (+) 12 Green/Red Left Rear Speaker (-) RIGHT REAR 1 Purple Right Rear Speaker (+) 9 Purple/Black Right Rear Speaker (-) RIGHT REAR 2 Purple Right Rear Speaker (+) 13 Purple/Red Right Rear Speaker (-) CENTER 1 Orange Center Speaker (+) 7 Orange/Black Center Speaker (-) SUB 1 Black Subwoofer 1 (+) 17 Black/White Subwoofer 1 (-) SUB 2 Black Subwoofer 2 (+) 17 Black/Red Subwoofer 2 (-) SUB 3 Black Subwoofer 3 (+) 16 Black/Yellow Subwoofer 3 (-) Amplifi er location: Left side of dash Note: The amplifi er output colors and labels on the AR-CH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, follow this wiring chart.

Kenwood amplifier PROGRAMMED FIRMWARE ADS-AR-CHR02 PRODUCTS REQUIRED iDatalink Maestro AR Amplifier Replacement Interface iDatalink Maestro AR-CH2 Installation Harness INSTALL GUIDE DODGE DURANGO 2014-2017 ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION, WITHOUT CHANGING YOUR RADIO. NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

Automotive Data Solutions Inc. © 2017 2 WELCOME NEED HELP? Congratulations on the purchase of your iDatalink Maestro AR Amplifi er replacement solution. You are now a few simple steps away from enjoying your new car amplifi er. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide. 1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum TABLE OF CONTENTS Settings and Features 3 Installation Instructions 4 Wiring Diagram 5 Vehicle Wire Reference Chart 6

Automotive Data Solutions Inc. © 2017 3 SETTINGS AND FEATURES CHIME ADJUSTMENT This is only needed when the vehicle supports chimes (ex: Parking assist, Blind spot detection, Lane sense, etc.). • Set the audio source to OFF. If there is no way to turn the radio OFF, set the source to AUX. • The OEM radio will have 3 volume settings for parking assist (Low/Med/High), it is recommended to choose Medium volume. • Activate any chime (ex: rear parking assist). • Adjust the chime volume using the volume knob. MAESTRO AR PROGRAMMABLE FEATURES These tone control features can be adjusted in the settings of the radio. • Bass Tone Control Subwoofer Volume • Mid Tone Control Not applicable • Treble Tone Control Tweeter Output Gain • Surround Control Not applicable • Speed Compensated Volume None 1

Automotive Data Solutions Inc. © 2017 4 INSTALLATION INSTRUCTIONS STEP 1 • Remove the factory amplifi er (refer to wire chart for amplifi er location). • Confi gure the 2 pin connectors on the AR-CH2 T-harness as shown on the wiring diagram. STEP 2 • Connect the factory amplifi er harnesses to the AR-CH2 T-harness. STEP 3 • Connect the wires from the AR-CH2 T-harness to the aftermarket amplifi er. Note 1: If you are running your own speaker wires from the amplifi er to the speakers, this step is not necessary. Note 2: The amplifi er output colors and labels on the CH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, see the wiring chart. • Plug the connector from the AR-CH2 T-Harness into the aftermarket amplifi er. • Plug the Data cable to the data port of the aftermarket amplifi er. STEP 4 • Connect all the harnesses to the Maestro AR module. • For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink. com/support” and “www.12voltdata.com/forum/” 1

Automotive Data Solutions Inc. © 2017 5 AMP TURN ON A B C B C 1 LEFT FRONT 1 RIGHT FRONT 1 LEFT REAR 1 RIGHT REAR 1 LEFT FRONT 2 RIGHT FRONT 2 LEFT REAR 2 RIGHT REAR 2 SUB 1 SUB 2 SUB 3 CENTER 1 A A STEP 1 STEP 2 STEP 3 STEP 4 MAESTRO AR MODULE MAESTRO AR MODULE DATA CABLE AR-CH2 T-HARNESS AR-CH2 T-HARNESS FACTORY AMPLIFIER HARNESSES KENWOOD AMPLIFIER KENWOOD AMPLIFLIER WIRES FROM VEHICLE WHITE (1) WHITE GREEN GREEN GRAY 18 PIN CONNECTOR GRAY BLUE PURPLE PURPLE RED WHITE (2) N.C. WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE/BLACK GRAY/RED WHITE/RED GRAY GREEN GREEN/RED PURPLE WHITE PURPLE PURPLE/RED BLACK BLACK/WHITE BLACK BLACK/RED BLACK BLACK/YELLOW ORANGE ORANGE/BLACK (1) NOTE: WHITE 2-PIN CONNECTOR IS ONLY NECESSARY IF THE VEHICLE HAS CHIMES. (2) NOTE: IF AN EXTENSION HARNESS IS BEING USED: - DO NOT CONNECT THE (2) WHITE 2-PIN ADAPTER TO THE PURPLE 2-PIN CONNECTOR. - CUT OFF THE WHITE 2-PIN CONNECTOR FROM THE ADAPTER CABLE. - CONNECT THE WHITE WIRE FROM ADAPTER TO RED WIRE (PIN 15) OF 18-PIN CONNECTOR. - CONNECT THE BLACK WIRE FROM ADAPTER TO RED/BLACK WIRE (PIN 6) OF 18-PIN CONNECTOR. - CONNECT THE OTHER SIDE OF ADAPTER TO MAESTRO AR MODULE (POSITION A). CONNECTION NOT REQUIRED SECOND AMP 18 PIN CONNECTOR N.C. CONNECT THE BLUE WIRE (PIN 16) TO SECOND AMPLIFIER (IF PRESENT) (TO TURN IT ON) WIRING DIAGRAM

Automotive Data Solutions Inc. © 2017 6 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 1 2 3 4 7 8 9 14 15 17 VEHICLE WIRE REFERENCE CHART T-Harness Wires Vehicle Wires Wire Tag Wire Color Speaker Wire Description Component Position LEFT FRONT 1 White Left Front Speaker (+) 1 White/Black Left Front Speaker (-) LEFT FRONT 2 White Left Front Tweeter (+) 3 White/Red Left Front Tweeter (-) RIGHT FRONT 1 Gray Right Front Speaker (+) 2 Gray/Black Right Front Speaker (-) RIGHT FRONT 2 Gray Right Front Tweeter (+) 4 Gray/Red Right Front Tweeter (-) LEFT REAR 1 Green Left Rear Speaker (+) 8 Green/Black Left Rear Speaker (-) LEFT REAR 2 Green Subwoofer 2 (+) 17 Green/Red Subwoofer 2 (-) RIGHT REAR 1 Purple Right Rear Speaker (+) 9 Purple/Black Right Rear Speaker (-) RIGHT REAR 2 Purple Subwoofer 1 (+) 17 Purple/Red Subwoofer 1 (-) CENTER 1 Orange Left Rear Tweeter (+) 14 Orange/Black Left Rear Tweeter (-) SUB 1 Black Right Rear Tweeter (+) 15 Black/White Right Rear Tweeter (-) SUB 2 Black n/a Black/Red n/a SUB 3 Black Center Speaker (+) 7 Black/Yellow Center Speaker (-) Amplifi er location: Left side of cargo area Note: The amplifi er output colors and labels on the AR-CH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, follow this wiring chart.

Kenwood amplifier PROGRAMMED FIRMWARE ADS-AR-CHR02 PRODUCTS REQUIRED iDatalink Maestro AR Amplifier Replacement Interface iDatalink Maestro AR-CH2 Installation Harness INSTALL GUIDE DODGE JOURNEy 2011-2017 ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION, WITHOUT CHANGING YOUR RADIO. NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

Automotive Data Solutions Inc. © 2017 2 WELCOME NEED HELP? Congratulations on the purchase of your iDatalink Maestro AR Amplifi er replacement solution. You are now a few simple steps away from enjoying your new car amplifi er. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide. 1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum TABLE OF CONTENTS Settings and Features 3 Installation Instructions 4 Wiring Diagram 5 Vehicle Wire Reference Chart 6

Automotive Data Solutions Inc. © 2017 3 SETTINGS AND FEATURES MAESTRO AR PROGRAMMABLE FEATURES These tone control features can be adjusted in the settings of the radio. • Bass Tone Control Subwoofer Volume • Mid Tone Control Not applicable • Treble Tone Control Tweeter Output Gain • Surround Control Not applicable • Speed Compensated Volume None 3

Automotive Data Solutions Inc. © 2017 4 INSTALLATION INSTRUCTIONS STEP 1 • Remove the factory amplifi er (refer to wire chart for amplifi er location). • Confi gure the 2 pin connectors on the AR-CH2 T-harness as shown on the wiring diagram. STEP 2 • Connect the factory amplifi er harnesses to the AR-CH2 T-harness. STEP 3 • Connect the wires from the AR-CH2 T-harness to the aftermarket amplifi er. Note 1: If you are running your own speaker wires from the amplifi er to the speakers, this step is not necessary. Note 2: The amplifi er output colors and labels on the CH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, see the wiring chart. • Plug the connector from the AR-CH2 T-Harness into the aftermarket amplifi er. • Plug the Data cable to the data port of the aftermarket amplifi er. STEP 4 • Connect all the harnesses to the Maestro AR module. • For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink. com/support” and “www.12voltdata.com/forum/” 3

Automotive Data Solutions Inc. © 2017 5 AMP TURN ON B C B C 3 LEFT FRONT 1 RIGHT FRONT 1 LEFT REAR 1 RIGHT REAR 1 LEFT FRONT 2 RIGHT FRONT 2 LEFT REAR 2 RIGHT REAR 2 SUB 1 SUB 2 SUB 3 CENTER 1 STEP 1 STEP 2 STEP 3 STEP 4 MAESTRO AR MODULE DATA CABLE AR-CH2 T-HARNESS FACTORY AMPLIFIER HARNESSES KENWOOD AMPLIFIER WIRES FROM VEHICLE WHITE WHITE GREEN GREEN GRAY GRAY BLUE PURPLE PURPLE RED N.C. N.C. WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE/BLACK GRAY/RED WHITE/RED GRAY GREEN GREEN/RED PURPLE WHITE PURPLE PURPLE/RED BLACK BLACK/WHITE BLACK BLACK/RED BLACK BLACK/YELLOW ORANGE ORANGE/BLACK CONNECTIONS NOT REQUIRED SECOND AMP 18 PIN CONNECTOR N.C. CONNECT THE BLUE WIRE (PIN 16) TO SECOND AMPLIFIER (IF PRESENT) (TO TURN IT ON) WIRING DIAGRAM

Automotive Data Solutions Inc. © 2017 6 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 1 2 5 6 8 9 18 VEHICLE WIRE REFERENCE CHART T-Harness Wires Vehicle Wires Wire Tag Wire Color Speaker Wire Description Component Position LEFT FRONT 1 White Left Front Speaker (+) 1 White/Black Left Front Speaker (-) LEFT FRONT 2 White Left Front Tweeter (+) 5 White/Red Left Front Tweeter (-) RIGHT FRONT 1 Gray Right Front Speaker (+) 2 Gray/Black Right Front Speaker (-) RIGHT FRONT 2 Gray Right Front Tweeter (+) 6 Gray/Red Right Front Tweeter (-) LEFT REAR 1 Green Left Rear Speaker (+) 8 Green/Black Left Rear Speaker (-) LEFT REAR 2 Green Subwoofer 1 (+) 18 Green/Red Subwoofer 1 (-) RIGHT REAR 1 Purple Right Rear Speaker (+) 9 Purple/Black Right Rear Speaker (-) RIGHT REAR 2 Purple Subwoofer 2 (+) 18 Purple/Red Subwoofer 2 (-) CENTER 1 Orange n/a Orange/Black n/a SUB 1 Black n/a Black/White n/a SUB 2 Black n/a Black/Red n/a SUB 3 Black n/a Black/Yellow n/a Amplifi er location: Center console Note: The amplifi er output colors and labels on the AR-CH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, follow this wiring chart.

Kenwood amplifier PROGRAMMED FIRMWARE ADS-AR-CHR02 PRODUCTS REQUIRED iDatalink Maestro AR Amplifier Replacement Interface iDatalink Maestro AR-CH2 Installation Harness INSTALL GUIDE JEEP CHEROkEE 2014-2017 ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION, WITHOUT CHANGING YOUR RADIO. NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

Automotive Data Solutions Inc. © 2017 2 WELCOME NEED HELP? Congratulations on the purchase of your iDatalink Maestro AR Amplifi er replacement solution. You are now a few simple steps away from enjoying your new car amplifi er. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide. 1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum TABLE OF CONTENTS Settings and Features 3 Installation Instructions 4 Wiring Diagram 5 Vehicle Wire Reference Chart 6

Automotive Data Solutions Inc. © 2017 3 SETTINGS AND FEATURES CHIME ADJUSTMENT This is only needed when the vehicle supports chimes (ex: Parking assist, Blind spot detection, Lane sense, etc.). • Set the audio source to OFF. If there is no way to turn the radio OFF, set the source to AUX. • The OEM radio will have 3 volume settings for parking assist (Low/Med/High), it is recommended to choose Medium volume. • Activate any chime (ex: rear parking assist). • Adjust the chime volume using the volume knob. MAESTRO AR PROGRAMMABLE FEATURES These tone control features can be adjusted in the settings of the radio. • Bass Tone Control Subwoofer Volume • Mid Tone Control Not applicable • Treble Tone Control Tweeter Output Gain • Surround Control Not applicable • Speed Compensated Volume None 1

Automotive Data Solutions Inc. © 2017 4 INSTALLATION INSTRUCTIONS STEP 1 • Remove the factory amplifi er (refer to wire chart for amplifi er location). • Confi gure the 2 pin connectors on the AR-CH2 T-harness as shown on the wiring diagram. STEP 2 • Connect the factory amplifi er harnesses to the AR-CH2 T-harness. STEP 3 • Connect the wires from the AR-CH2 T-harness to the aftermarket amplifi er. Note 1: If you are running your own speaker wires from the amplifi er to the speakers, this step is not necessary. Note 2: The amplifi er output colors and labels on the CH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, see the wiring chart. • Plug the connector from the AR-CH2 T-Harness into the aftermarket amplifi er. • Plug the Data cable to the data port of the aftermarket amplifi er. STEP 4 • Connect all the harnesses to the Maestro AR module. • For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink. com/support” and “www.12voltdata.com/forum/” 1

Automotive Data Solutions Inc. © 2017 5 AMP TURN ON A B C B C 1 LEFT FRONT 1 RIGHT FRONT 1 LEFT REAR 1 RIGHT REAR 1 LEFT FRONT 2 RIGHT FRONT 2 LEFT REAR 2 RIGHT REAR 2 SUB 1 SUB 2 SUB 3 CENTER 1 A A STEP 1 STEP 2 STEP 3 STEP 4 MAESTRO AR MODULE MAESTRO AR MODULE DATA CABLE AR-CH2 T-HARNESS AR-CH2 T-HARNESS FACTORY AMPLIFIER HARNESSES KENWOOD AMPLIFIER KENWOOD AMPLIFLIER WIRES FROM VEHICLE WHITE (1) WHITE GREEN GREEN GRAY 18 PIN CONNECTOR GRAY BLUE PURPLE PURPLE RED WHITE (2) N.C. WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE/BLACK GRAY/RED WHITE/RED GRAY GREEN GREEN/RED PURPLE WHITE PURPLE PURPLE/RED BLACK BLACK/WHITE BLACK BLACK/RED BLACK BLACK/YELLOW ORANGE ORANGE/BLACK (1) NOTE: WHITE 2-PIN CONNECTOR IS ONLY NECESSARY IF THE VEHICLE HAS CHIMES. (2) NOTE: IF AN EXTENSION HARNESS IS BEING USED: - DO NOT CONNECT THE (2) WHITE 2-PIN ADAPTER TO THE PURPLE 2-PIN CONNECTOR. - CUT OFF THE WHITE 2-PIN CONNECTOR FROM THE ADAPTER CABLE. - CONNECT THE WHITE WIRE FROM ADAPTER TO RED WIRE (PIN 15) OF 18-PIN CONNECTOR. - CONNECT THE BLACK WIRE FROM ADAPTER TO RED/BLACK WIRE (PIN 6) OF 18-PIN CONNECTOR. - CONNECT THE OTHER SIDE OF ADAPTER TO MAESTRO AR MODULE (POSITION A). CONNECTION NOT REQUIRED SECOND AMP 18 PIN CONNECTOR N.C. CONNECT THE BLUE WIRE (PIN 16) TO SECOND AMPLIFIER (IF PRESENT) (TO TURN IT ON) WIRING DIAGRAM

Automotive Data Solutions Inc. © 2017 6 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 1 2 3 4 7 8 9 10 11 17 18 VEHICLE WIRE REFERENCE CHART T-Harness Wires Vehicle Wires Wire Tag Wire Color Speaker Wire Description Component Position LEFT FRONT 1 White Left Front Speaker (+) 1 White/Black Left Front Speaker (-) LEFT FRONT 2 White Left Front Tweeter (+) 3 White/Red Left Front Tweeter (-) RIGHT FRONT 1 Gray Right Front Speaker (+) 2 Gray/Black Right Front Speaker (-) RIGHT FRONT 2 Gray Right Front Tweeter (+) 4 Gray/Red Right Front Tweeter (-) LEFT REAR 1 Green Left Rear Tweeter (+) 11 Green/Black Left Rear Tweeter (-) LEFT REAR 2 Green Subwoofer 1 (+) 18 Green/Red Subwoofer 1 (-) RIGHT REAR 1 Purple Right Rear Tweeter (+) 10 Purple/Black Right Rear Tweeter (-) RIGHT REAR 2 Purple Subwoofer 2 (+) 17 Purple/Red Subwoofer 2 (-) CENTER 1 Orange Left Rear Speaker (+) 8 Orange/Black Left Rear Speaker (-) SUB 1 Black n/a Black/White n/a SUB 2 Black Right Rear Speaker (+) 9 Black/Red Right Rear Speaker (-) SUB 3 Black Center Speaker (+) 7 Black/Yellow Center Speaker (-) Amplifi er location: Right end of dash Note: The amplifi er output colors and labels on the AR-CH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, follow this wiring chart.

Kenwood amplifier PROGRAMMED FIRMWARE ADS-AR-CHR02 PRODUCTS REQUIRED iDatalink Maestro AR Amplifier Replacement Interface iDatalink Maestro AR-CH2 Installation Harness INSTALL GUIDE JEEP GRAND CHEROkEE 2014-2017 ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION, WITHOUT CHANGING YOUR RADIO. NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

Automotive Data Solutions Inc. © 2017 2 WELCOME NEED HELP? Congratulations on the purchase of your iDatalink Maestro AR Amplifi er replacement solution. You are now a few simple steps away from enjoying your new car amplifi er. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide. 1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum TABLE OF CONTENTS Settings and Features 3 Installation Instructions 4 Wiring Diagram 5 Vehicle Wire Reference Chart 6

Automotive Data Solutions Inc. © 2017 3 SETTINGS AND FEATURES CHIME ADJUSTMENT This is only needed when the vehicle supports chimes (ex: Parking assist, Blind spot detection, Lane sense, etc.). • Set the audio source to OFF. If there is no way to turn the radio OFF, set the source to AUX. • The OEM radio will have 3 volume settings for parking assist (Low/Med/High), it is recommended to choose Medium volume. • Activate any chime (ex: rear parking assist). • Adjust the chime volume using the volume knob. MAESTRO AR PROGRAMMABLE FEATURES These tone control features can be adjusted in the settings of the radio. • Bass Tone Control Subwoofer Volume • Mid Tone Control Not applicable • Treble Tone Control Tweeter Output Gain • Surround Control Not applicable • Speed Compensated Volume None 1

Automotive Data Solutions Inc. © 2017 4 INSTALLATION INSTRUCTIONS STEP 1 • Remove the factory amplifi er (refer to wire chart for amplifi er location). • Confi gure the 2 pin connectors on the AR-CH2 T-harness as shown on the wiring diagram. STEP 2 • Connect the factory amplifi er harnesses to the AR-CH2 T-harness. STEP 3 • Connect the wires from the AR-CH2 T-harness to the aftermarket amplifi er. Note 1: If you are running your own speaker wires from the amplifi er to the speakers, this step is not necessary. Note 2: The amplifi er output colors and labels on the CH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, see the wiring chart. • Plug the connector from the AR-CH2 T-Harness into the aftermarket amplifi er. • Plug the Data cable to the data port of the aftermarket amplifi er. STEP 4 • Connect all the harnesses to the Maestro AR module. • For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink. com/support” and “www.12voltdata.com/forum/” 1

Automotive Data Solutions Inc. © 2017 5 AMP TURN ON A B C B C 1 LEFT FRONT 1 RIGHT FRONT 1 LEFT REAR 1 RIGHT REAR 1 LEFT FRONT 2 RIGHT FRONT 2 LEFT REAR 2 RIGHT REAR 2 SUB 1 SUB 2 SUB 3 CENTER 1 A A STEP 1 STEP 2 STEP 3 STEP 4 MAESTRO AR MODULE MAESTRO AR MODULE DATA CABLE AR-CH2 T-HARNESS AR-CH2 T-HARNESS FACTORY AMPLIFIER HARNESSES KENWOOD AMPLIFIER KENWOOD AMPLIFLIER WIRES FROM VEHICLE WHITE (1) WHITE GREEN GREEN GRAY 18 PIN CONNECTOR GRAY BLUE PURPLE PURPLE RED WHITE (2) N.C. WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE/BLACK GRAY/RED WHITE/RED GRAY GREEN GREEN/RED PURPLE WHITE PURPLE PURPLE/RED BLACK BLACK/WHITE BLACK BLACK/RED BLACK BLACK/YELLOW ORANGE ORANGE/BLACK (1) NOTE: WHITE 2-PIN CONNECTOR IS ONLY NECESSARY IF THE VEHICLE HAS CHIMES. (2) NOTE: IF AN EXTENSION HARNESS IS BEING USED: - DO NOT CONNECT THE (2) WHITE 2-PIN ADAPTER TO THE PURPLE 2-PIN CONNECTOR. - CUT OFF THE WHITE 2-PIN CONNECTOR FROM THE ADAPTER CABLE. - CONNECT THE WHITE WIRE FROM ADAPTER TO RED WIRE (PIN 15) OF 18-PIN CONNECTOR. - CONNECT THE BLACK WIRE FROM ADAPTER TO RED/BLACK WIRE (PIN 6) OF 18-PIN CONNECTOR. - CONNECT THE OTHER SIDE OF ADAPTER TO MAESTRO AR MODULE (POSITION A). CONNECTION NOT REQUIRED SECOND AMP 18 PIN CONNECTOR N.C. CONNECT THE BLUE WIRE (PIN 16) TO SECOND AMPLIFIER (IF PRESENT) (TO TURN IT ON) WIRING DIAGRAM

Automotive Data Solutions Inc. © 2017 6 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 1 2 3 4 7 8 9 14 15 17 VEHICLE WIRE REFERENCE CHART T-Harness Wires Vehicle Wires Wire Tag Wire Color Speaker Wire Description Component Position LEFT FRONT 1 White Left Front Speaker (+) 1 White/Black Left Front Speaker (-) LEFT FRONT 2 White Left Front Tweeter (+) 3 White/Red Left Front Tweeter (-) RIGHT FRONT 1 Gray Right Front Speaker (+) 2 Gray/Black Right Front Speaker (-) RIGHT FRONT 2 Gray Right Front Tweeter (+) 4 Gray/Red Right Front Tweeter (-) LEFT REAR 1 Green Left Rear Speaker (+) 8 Green/Black Left Rear Speaker (-) LEFT REAR 2 Green Subwoofer 2 (+) 17 Green/Red Subwoofer 2 (-) RIGHT REAR 1 Purple Right Rear Speaker (+) 9 Purple/Black Right Rear Speaker (-) RIGHT REAR 2 Purple Subwoofer 1 (+) 17 Purple/Red Subwoofer 1 (-) CENTER 1 Orange Left Rear Speaker (+) 14 Orange/Black Left Rear Speaker (-) SUB 1 Black Right Rear Speaker (+) 15 Black/White Right Rear Speaker (-) SUB 2 Black n/a Black/Red n/a SUB 3 Black Center Speaker (+) 7 Black/Yellow Center Speaker (-) Amplifi er location: Left side of cargo area Note: The amplifi er output colors and labels on the AR-CH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, follow this wiring chart.

Kenwood amplifier PROGRAMMED FIRMWARE ADS-AR-CHR02 PRODUCTS REQUIRED iDatalink Maestro AR Amplifier Replacement Interface iDatalink Maestro AR-CH2 Installation Harness INSTALL GUIDE RAM 1500 2013-2017 ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION, WITHOUT CHANGING YOUR RADIO. NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

Automotive Data Solutions Inc. © 2017 2 WELCOME NEED HELP? Congratulations on the purchase of your iDatalink Maestro AR Amplifi er replacement solution. You are now a few simple steps away from enjoying your new car amplifi er. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide. 1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum TABLE OF CONTENTS Settings and Features 3 Installation Instructions 4 Wiring Diagram 5 Vehicle Wire Reference Chart 6

Automotive Data Solutions Inc. © 2017 3 SETTINGS AND FEATURES CHIME ADJUSTMENT This is only needed when the vehicle supports chimes (ex: Parking assist, Blind spot detection, Lane sense, etc.). • Set the audio source to OFF. If there is no way to turn the radio OFF, set the source to AUX. • The OEM radio will have 3 volume settings for parking assist (Low/Med/High), it is recommended to choose Medium volume. • Activate any chime (ex: rear parking assist). • Adjust the chime volume using the volume knob. MAESTRO AR PROGRAMMABLE FEATURES These tone control features can be adjusted in the settings of the radio. • Bass Tone Control Subwoofer Volume • Mid Tone Control Not applicable • Treble Tone Control Tweeter Output Gain • Surround Control Not applicable • Speed Compensated Volume None 1

Automotive Data Solutions Inc. © 2017 4 INSTALLATION INSTRUCTIONS STEP 1 • Remove the factory amplifi er (refer to wire chart for amplifi er location). • Confi gure the 2 pin connectors on the AR-CH2 T-harness as shown on the wiring diagram. STEP 2 • Connect the factory amplifi er harnesses to the AR-CH2 T-harness. STEP 3 • Connect the wires from the AR-CH2 T-harness to the aftermarket amplifi er. Note 1: If you are running your own speaker wires from the amplifi er to the speakers, this step is not necessary. Note 2: The amplifi er output colors and labels on the CH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, see the wiring chart. • Plug the connector from the AR-CH2 T-Harness into the aftermarket amplifi er. • Plug the Data cable to the data port of the aftermarket amplifi er. STEP 4 • Connect all the harnesses to the Maestro AR module. • For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink. com/support” and “www.12voltdata.com/forum/” 1

Automotive Data Solutions Inc. © 2017 5 AMP TURN ON A B C B C 1 LEFT FRONT 1 RIGHT FRONT 1 LEFT REAR 1 RIGHT REAR 1 LEFT FRONT 2 RIGHT FRONT 2 LEFT REAR 2 RIGHT REAR 2 SUB 1 SUB 2 SUB 3 CENTER 1 A A STEP 1 STEP 2 STEP 3 STEP 4 MAESTRO AR MODULE MAESTRO AR MODULE DATA CABLE AR-CH2 T-HARNESS AR-CH2 T-HARNESS FACTORY AMPLIFIER HARNESSES KENWOOD AMPLIFIER KENWOOD AMPLIFLIER WIRES FROM VEHICLE WHITE (1) WHITE GREEN GREEN GRAY 18 PIN CONNECTOR GRAY BLUE PURPLE PURPLE RED WHITE (2) N.C. WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE/BLACK GRAY/RED WHITE/RED GRAY GREEN GREEN/RED PURPLE WHITE PURPLE PURPLE/RED BLACK BLACK/WHITE BLACK BLACK/RED BLACK BLACK/YELLOW ORANGE ORANGE/BLACK (1) NOTE: WHITE 2-PIN CONNECTOR IS ONLY NECESSARY IF THE VEHICLE HAS CHIMES. (2) NOTE: IF AN EXTENSION HARNESS IS BEING USED: - DO NOT CONNECT THE (2) WHITE 2-PIN ADAPTER TO THE PURPLE 2-PIN CONNECTOR. - CUT OFF THE WHITE 2-PIN CONNECTOR FROM THE ADAPTER CABLE. - CONNECT THE WHITE WIRE FROM ADAPTER TO RED WIRE (PIN 15) OF 18-PIN CONNECTOR. - CONNECT THE BLACK WIRE FROM ADAPTER TO RED/BLACK WIRE (PIN 6) OF 18-PIN CONNECTOR. - CONNECT THE OTHER SIDE OF ADAPTER TO MAESTRO AR MODULE (POSITION A). CONNECTION NOT REQUIRED SECOND AMP 18 PIN CONNECTOR N.C. CONNECT THE BLUE WIRE (PIN 16) TO SECOND AMPLIFIER (IF PRESENT) (TO TURN IT ON) WIRING DIAGRAM

Automotive Data Solutions Inc. © 2017 6 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 1 2 5 6 7 8 9 14 15 17 VEHICLE WIRE REFERENCE CHART T-Harness Wires Vehicle Wires Wire Tag Wire Color Speaker Wire Description Component Position LEFT FRONT 1 White Left Front Speaker (+) 1 White/Black Left Front Speaker (-) LEFT FRONT 2 White Left Front Tweeter (+) 5 White/Red Left Front Tweeter (-) RIGHT FRONT 1 Gray Right Front Speaker (+) 2 Gray/Black Right Front Speaker (-) RIGHT FRONT 2 Gray Right Front Tweeter (+) 6 Gray/Red Right Front Tweeter (-) LEFT REAR 1 Green Left Rear Speaker (+) 8 Green/Black Left Rear Speaker (-) LEFT REAR 2 Green Subwoofer 1 (+) 17 Green/Red Subwoofer 1 (-) RIGHT REAR 1 Purple Right Rear Speaker (+) 9 Purple/Black Right Rear Speaker (-) RIGHT REAR 2 Purple Center Speaker (+) 7 Purple/Red Center Speaker (-) CENTER 1 Orange Left Rear Tweeter (+) 14 Orange/Black Left Rear Tweeter (-) SUB 1 Black Right Rear Tweeter (+) 15 Black/White Right Rear Tweeter (-) SUB 2 Black n/a Black/Red n/a SUB 3 Black Subwoofer 2 (+) 17 Black/Yellow Subwoofer 2 (-) Amplifi er location: Left end of dash Note: The amplifi er output colors and labels on the AR-CH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, follow this wiring chart.

Kenwood amplifier PROGRAMMED FIRMWARE ADS-AR-CHR02 PRODUCTS REQUIRED iDatalink Maestro AR Amplifier Replacement Interface iDatalink Maestro AR-CH2 Installation Harness INSTALL GUIDE RAM 2500 & 3500 2013-2017 ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION, WITHOUT CHANGING YOUR RADIO. NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

Automotive Data Solutions Inc. © 2017 2 WELCOME NEED HELP? Congratulations on the purchase of your iDatalink Maestro AR Amplifi er replacement solution. You are now a few simple steps away from enjoying your new car amplifi er. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide. 1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum TABLE OF CONTENTS Settings and Features 3 Installation Instructions 4 Wiring Diagram 5 Vehicle Wire Reference Chart 6

Automotive Data Solutions Inc. © 2017 3 SETTINGS AND FEATURES CHIME ADJUSTMENT This is only needed when the vehicle supports chimes (ex: Parking assist, Blind spot detection, Lane sense, etc.). • Set the audio source to OFF. If there is no way to turn the radio OFF, set the source to AUX. • The OEM radio will have 3 volume settings for parking assist (Low/Med/High), it is recommended to choose Medium volume. • Activate any chime (ex: rear parking assist). • Adjust the chime volume using the volume knob. MAESTRO AR PROGRAMMABLE FEATURES These tone control features can be adjusted in the settings of the radio. • Bass Tone Control Subwoofer Volume • Mid Tone Control Not applicable • Treble Tone Control Tweeter Output Gain • Surround Control Not applicable • Speed Compensated Volume None 1

Automotive Data Solutions Inc. © 2017 4 INSTALLATION INSTRUCTIONS STEP 1 • Remove the factory amplifi er (refer to wire chart for amplifi er location). • Confi gure the 2 pin connectors on the AR-CH2 T-harness as shown on the wiring diagram. STEP 2 • Connect the factory amplifi er harnesses to the AR-CH2 T-harness. STEP 3 • Connect the wires from the AR-CH2 T-harness to the aftermarket amplifi er. Note 1: If you are running your own speaker wires from the amplifi er to the speakers, this step is not necessary. Note 2: The amplifi er output colors and labels on the CH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, see the wiring chart. • Plug the connector from the AR-CH2 T-Harness into the aftermarket amplifi er. • Plug the Data cable to the data port of the aftermarket amplifi er. STEP 4 • Connect all the harnesses to the Maestro AR module. • For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink. com/support” and “www.12voltdata.com/forum/” 1

Automotive Data Solutions Inc. © 2017 5 AMP TURN ON A B C B C 1 LEFT FRONT 1 RIGHT FRONT 1 LEFT REAR 1 RIGHT REAR 1 LEFT FRONT 2 RIGHT FRONT 2 LEFT REAR 2 RIGHT REAR 2 SUB 1 SUB 2 SUB 3 CENTER 1 A A STEP 1 STEP 2 STEP 3 STEP 4 MAESTRO AR MODULE MAESTRO AR MODULE DATA CABLE AR-CH2 T-HARNESS AR-CH2 T-HARNESS FACTORY AMPLIFIER HARNESSES KENWOOD AMPLIFIER KENWOOD AMPLIFLIER WIRES FROM VEHICLE WHITE (1) WHITE GREEN GREEN GRAY 18 PIN CONNECTOR GRAY BLUE PURPLE PURPLE RED WHITE (2) N.C. WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE/BLACK GRAY/RED WHITE/RED GRAY GREEN GREEN/RED PURPLE WHITE PURPLE PURPLE/RED BLACK BLACK/WHITE BLACK BLACK/RED BLACK BLACK/YELLOW ORANGE ORANGE/BLACK (1) NOTE: WHITE 2-PIN CONNECTOR IS ONLY NECESSARY IF THE VEHICLE HAS CHIMES. (2) NOTE: IF AN EXTENSION HARNESS IS BEING USED: - DO NOT CONNECT THE (2) WHITE 2-PIN ADAPTER TO THE PURPLE 2-PIN CONNECTOR. - CUT OFF THE WHITE 2-PIN CONNECTOR FROM THE ADAPTER CABLE. - CONNECT THE WHITE WIRE FROM ADAPTER TO RED WIRE (PIN 15) OF 18-PIN CONNECTOR. - CONNECT THE BLACK WIRE FROM ADAPTER TO RED/BLACK WIRE (PIN 6) OF 18-PIN CONNECTOR. - CONNECT THE OTHER SIDE OF ADAPTER TO MAESTRO AR MODULE (POSITION A). CONNECTION NOT REQUIRED SECOND AMP 18 PIN CONNECTOR N.C. CONNECT THE BLUE WIRE (PIN 16) TO SECOND AMPLIFIER (IF PRESENT) (TO TURN IT ON) WIRING DIAGRAM

Automotive Data Solutions Inc. © 2017 6 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 1 2 5 6 7 14 15 17 VEHICLE WIRE REFERENCE CHART T-Harness Wires Vehicle Wires Wire Tag Wire Color Speaker Wire Description Component Position LEFT FRONT 1 White Left Front Speaker (+) 1 White/Black Left Front Speaker (-) LEFT FRONT 2 White Left Front Tweeter (+) 5 White/Red Left Front Tweeter (-) RIGHT FRONT 1 Gray Right Front Speaker (+) 2 Gray/Black Right Front Speaker (-) RIGHT FRONT 2 Gray Right Front Tweeter (+) 6 Gray/Red Right Front Tweeter (-) LEFT REAR 1 Green Left Rear Speaker (+) Green/Black Left Rear Speaker (-) LEFT REAR 2 Green Subwoofer 1 (+) 17 Green/Red Subwoofer 1 (-) RIGHT REAR 1 Purple Right Rear Speaker (+) Purple/Black Right Rear Speaker (-) RIGHT REAR 2 Purple Center Speaker (+) 7 Purple/Red Center Speaker (-) CENTER 1 Orange Left Rear Tweeter (+) 14 Orange/Black Left Rear Tweeter (-) SUB 1 Black Right Rear Tweeter (+) 15 Black/White Right Rear Tweeter (-) SUB 2 Black n/a Black/Red n/a SUB 3 Black Subwoofer 2 (+) 17 Black/Yellow Subwoofer 2 (-) Amplifi er location: Left end of dash Note: The amplifi er output colors and labels on the AR-CH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, follow this wiring chart.