Emerson Rosemount 65Q Manual 

September 2014 00813-0100-4827, Rev DA  Resistance temperature sensors for applications in the food and beverage, pharmaceutical and life-science industries  Aseptic process connections suitable for CIP and SIP dead-pocket free measurement applications  Exchangeable measuring insert to ensure process integrity  Enhanced system accuracy with transmitter-sensor matching, meets pharmaceutical industry requirements Resistance Temperature Sensors for Hygienic and Sanitary Applications Product Discontinued

Optimize plant efficiency and increase measurement reliability with industry proven design and specifications  RTD elements for a reliable and accurate measurement point  Available in a wide variety of process connections for sanitary and hygienic applications  Meets EHEDG and 3-A Standard requirements for use in a variety of sanitary  Flying leads, terminal blocks, and cable connections to suit different wiring needs  State of the art manufacturing procedures provide robust element packaging, increasing reliability  Industry-leading calibration capabilities allow for Callendar-van-Dusen values to give increased accuracy when paired with Rosemount transmitters Streamline operations and maintenance with sensor and thermowell design  Process connections allow for quick and easy connection to industry-standard sanitary process connection points  Integral thermowell protection on 65Q allows for ordering sanitary sensor and thermowell together Explore the benefits of a Complete Point Solution from Rosemount Temperature Measurement  An “Assemble Sensor to Specific Transmitter” option enables Emerson to provide a complete point temperature solution, delivering an installation-ready transmitter and sensor assembly.  Emerson has a complete portfolio of Single Point and High Density Temperature Measurement solutions, allowing you to effectively measure and control your processes with the reliability you trust from Rosemount products. Experience global consistency and local support from numerous worldwide Rosemount Temperature sites  World-class manufacturing provides globally consistent ‘‘‘‘‘‘‘‘‘‘‘ ‘ product from every factory and the capability to fulfill the ‘‘‘‘‘‘‘‘ ‘ needs of any project, large or small.  Experienced Instrumentation Consultants help select the right product for any temperature application and advise on best installation practices.  An extensive global network of Emerson service and support personnel can be on-site when and where they are needed.

Rosemount 65Q Sanitary Sensor . . . . . . . . . . . . . . . . . . . . . . . 4 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Dimensional Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

The Rosemount 65Q Sanitary Sensor has designs that provide flexible and reliable temperature measurements in hygienic process environments. Features include:  – 50 to 450 °C temperature range  Industry-standard RTD sensor design  3-A and EHEDG Standards approval  Variety of enclosure and connection head options  Global hazardous-location approvals (Option Code I1)  Calibration services to give you insight to sensor performance (Option Codes V10, V11)  Electropolishing Surface Finish (Option Code R20)  Assemble to Transmitter option (Option Code XA) Specification and selection of product materials, options, or components must be made by the purchaser of the equipment. See page 10 for more information on Material Selection. Table 1. 65Q RTD Assembly (Pt 100) for Hygienic and Food and Beverage Applications ★ The Standard offering represents the most common options. The starred options (★) should be selected for best delivery. __The Expanded offering is subject to additional delivery lead time. Model Product description 0065Q 65Q RTD Sensor with Twell for Sanitary Applications Connection head IP rating(1) Connection thread C Rosemount Aluminum 68 M20 x 1.5 ★ D Rosemount Aluminum 68 1/2-in. NPT ★ 1 Rosemount, Aluminum with LCD Display Cover 68 M20 x 1.5 ★ 2 Rosemount, Aluminum with LCD Display Cover 68 1/2-in. NPT ★ 5 Connection Head DIN A Polished Stainless Steel with LCD Display Cover 68 M20 x 1.5 ★ 6 Connection Head DIN A Polished Stainless Steel with LCD Display Cover 68 1/2-in. NPT ★ E Connection Head DIN A Polished Stainless Steel 68 M20 x 1.5 ★ F Connection Head DIN A Polished Stainless Steel 68 1/2-in. NPT ★ R Connection Head DIN B Polished Stainless Steel 66 M20 x 1.5 ★ S Connection Head DIN B Polished Stainless Steel 66 1/2-in. NPT ★ J GR-A/BL (BUZ), Aluminum 65 M20 x 1.5 (with cable gland) L TZ-A/BL (BUZH) Aluminum 65 M20 x 1.5 (with cable gland) T TZ-A/BK, Polyamide, Black 65 M20 x 1.5 (with cable gland)

0 Flying Leads – No Springs on DIN plate ★ 2 Terminal Block – DIN 43762 ★ Sensor type Temperature range 1 RTD, Single Element, 4-wire – 50 to 450 °C ★ 2 RTD, Dual Element, 3-wire – 50 to 450 °C ★ 5 RTD, Single Element, 3-wire – 50 to 450 °C ★ Extension S Tubular with Extension, Welded Screw Bush M24 x 1.5 ★ Z Tubular with Extension, Head Connection Adjustable Loose Screw Nut M24 x 1.5 ★ Extension length (N) in millimeters 0050(2) 50 mm ★ 0065(3) 65 mm ★ 0130 130 mm ★ XXXX Non-standard extension length – non-standard lengths are available from 50 to 990 mm ★ Thermowell material D 1.4404 (AISI 316L) Stainless Steel, ≤ 0.8 μm electropolishing ★ Immersion length (L) in millimeters 0025 25 mm – not available for Mounting Style code T02 ★ 0050 50 mm ★ 0065 65 mm ★ 0100 100 mm ★ 0150 150 mm ★ 0200 200 mm ★ 0250 250 mm ★ XXXX Non-standard immersion length – non-standard lengths are available from 25 to 2500 mm Thermowell mounting style Process connection Stem style C02 Flanged 1-in. Tri-Clamp™ (diameter 50.4 mm) Stepped, 10/6 mm(4) ★ C04 Flanged 11/2-in. Tri-Clamp (diameter 50.4 mm) Stepped, 10/6 mm(4) ★ C06 Flanged 2-in. Tri-Clamp (diameter 64 mm) Stepped, 10/6 mm(4) ★ C08 Flanged 21/2-in. Tri-Clamp (diameter 77.4 mm) Stepped, 10/6 mm(4) ★ C10 Flanged 3-in. Tri-Clamp (diameter 91 mm) Stepped, 10/6 mm(4) ★ C12 Flanged 4-in. Tri-Clamp (diameter 119 mm) Stepped, 10/6 mm(4) ★ C14 Flanged 1/2-in. Tri-Clamp (diameter 24.9 mm) Stepped, 10/6 mm(4) ★ Table 1. 65Q RTD Assembly (Pt 100) for Hygienic and Food and Beverage Applications ★ The Standard offering represents the most common options. The starred options (★) should be selected for best delivery. __The Expanded offering is subject to additional delivery lead time.

Stepped, 10/6 mm(4) ★ K02 Weld-in Ball (adjustable), diameter 25 mm, PEEK Seal Straight, 6 mm(5) ★ K04 Weld-in Ball (adjustable), diameter 25 mm, SST Seal Straight, 6 mm(5) ★ M10 Tapered with Coupling Nut(6) Suitable connection for tube nominal size DN 10 Stepped, 10/6 mm(4) ★ M25 Tapered Union with Coupling Nut(6) Suitable connection for tube nominal size DN 25 Stepped, 10/6 mm(4) ★ M32 Tapered Union with Coupling Nut(6) Suitable connection for tube nominal size DN 32 Stepped, 10/6 mm(4) ★ M40 Tapered Union with Coupling Nut(6) Suitable connection for tube nominal size DN 40 Stepped, 10/6 mm(4) ★ M50 Tapered Union with Coupling Nut(6) Suitable connection for tube nominal size DN 50 Stepped, 10/6 mm(4) ★ T02 Threaded Parallel 1/2-in. (1/2-in. BSPF) (G1/2) Stepped, 10/6 mm(7) ★ T12 Threaded Tapered 1/2-in. NPT Stepped, 10/6 mm(4) ★ V04 VARIVENT® DN 1 1/2 - 3 inch (Dim. 68 mm) Standard ★ Options (include with selected model number) Sensor options A3 Single Element Class 1/3 DIN B Sensor 0 to 100 °C (–32 to 212 °F) A4 Dual Element Class 1/3 DIN B Sensor 0 to 100 °C (–32 to 212 °F) Product certifications I1 EEx ia ATEX/IBExU Intrinsic Safety Approval ★ Cable gland option G2 Cable Gland, EEx d, Brass 7.5 mm - 11.9 mm ★ Cover chain option G3 Cover Chain (only available with Connection Head Material codes C and D) ★ Extension ring G6 Aluminum Extension Ring for Dual Transmitter Mounting (only available with Connection Head Material codes C and D) ★ Material certification Q8 Thermowell Material Certification ★ Extension ring R20 Electropolishing Surface Finish of wetted parts, Ra = 0.4 μm Assemble to options XA(8) Assemble Sensor to Specific Temperature Transmitter ★ Table 1. 65Q RTD Assembly (Pt 100) for Hygienic and Food and Beverage Applications ★ The Standard offering represents the most common options. The starred options (★) should be selected for best delivery. __The Expanded offering is subject to additional delivery lead time.

V10 Works Certificate – Sensor Calibration from –50 to 450 °C (-58 to 842 °F) ★ V11 Works Certificate – Sensor Calibration from 0 to 100 °C (-32 to 212 °F) ★ Temperature range X8 Works Certificate – Sensor Calibration Over Specified Temperature Range with A, B, C, and Callendar-van Dusen constants ★ Typical model number: 0065Q C 0 1 S 0050 D 0200 C04 XA (1) IP 68 rating requires a suitable cable gland on the conduit connection thread. All threads must be sealed. (2) Standard length for use with Connection Head codes C, D, 1, and 2. (3) Standard length for use with Connection Head codes E, F, J, L, R, S, T, 5,and 6. (4) For U < 50 mm, outer diameter 6 mm straight, below part of process connection. (5) Valid for DIN B connection heads only. (6) According to DIN 11851. (7) For Up ≤ 65 mm, the outer diameter is 6 mm for straight stem styles. (8) If ordering XA with a transmitter, specify the same option on the transmitter model number. Table 1. 65Q RTD Assembly (Pt 100) for Hygienic and Food and Beverage Applications ★ The Standard offering represents the most common options. The starred options (★) should be selected for best delivery. __The Expanded offering is subject to additional delivery lead time.

in hygienic and aseptic applications exclusively to meet the stringent quality requirements in the Food and Beverage, and Pharmaceutical industries. Rosemount temperature products are manufactured according to Good Manufacturing Practice (GMP) guidelines and comply with the standards of the European Hygienic Equipment Design Group (EHEDG) as well as 3A standards. National and international guidelines Products that may have a direct or indirect impact on public health, must be produced according to national and international guidelines. The guidelines contain rules for the implementation and organization of methods, production, production environments, and inspections. The European Hygienic Equipment Design Group (EHEDG) is a foundation in which mainly users and manufacturers or hygienic equipment are represented. EHEDG provides guidance of the hygienic engineering aspects of manufacturing of safe and wholesome food, e.g. through production, publication, and updating of guidelines, equipment approval through certification to assist equipment suppliers and food manufacturers and advisory function to legislators and standards groups. EHEDG cooperation with 3-A EHEDG cooperates with 3-A Sanitary Standards, Inc. in the development of hygienic construction material selection and design standards for food and dairy processing equipment. 3-A Sanitary Standards and Practices have been developed for use by the dairy industry, dairy equipment manufacturers, and milk regulatory agencies as voluntary guidelines. These voluntary guidelines are used as a benchmark for product performance, hygienic quality, and ultimately food safety. 3-A Sanitary Standards and Practices are generally accepted by federal, state, and local public health authorities in the United States and other public health authorities around the world. While 3-A Sanitary Standards have been in development and use since the late 1920’s. EHEDG is a fairly recent development that applies test criteria and laboratory test data for determining cleanability and acceptance for equipment use in the processing of foods or comestibles. Both EHEDG and 3-A Sanitary Standards may be applied not only to Food and Beverage processing equipment, but can also be applied to Biotech and Bio-pharm equipment to ensure product acceptance and safety. Mounting configurations The Rosemount 65Q can be ordered with flying leads or terminal block. Ordered with flying leads, the sensors are designed with an integral mounting plate, and are for use with a head-mount transmitter attached directly to the sensor. The flying lead configuration facilitates removal of the sensor and transmitter as one assembly. The configuration with terminal block allows only the mounting of transmitter into the cover of several DIN size connection heads or requires the use of field mount transmitter. Series 65Q RTD – sanitary applications Rosemount Series 65Q Integral Mount Temperature Sensors are designed for use in hygienic, food and beverage applications when fitted with the Tri-Clamp, adjustable Weld-in Ball or Tapered Union with Coupling Nut according to DIN 11851 (Dairy Connection) process connections which do not need to meet as harsh aseptic requirements as requested for BioPharm applications. Alternatively for direct insertion into non-hygienic processes, the Series 65Q Temperature Sensor can be ordered optional with G½-in. (½-in. BSPF) or ½-in. NPT thread mounting. The 65Q is available alone or as complete assemblies including connection heads, thermowells with weld-on process connections. This offering is designed to be used in complete temperature assemblies including Rosemount Temperature Transmitters. The RTD sensors meet most critical parameters of international standards - DIN EN 60751 incorporating Amendments 1 and 2. All sensors are available in a variety of lengths and ranges with terminal block or flying leads.

Series 65 RTD flying leads (Code 0) Single element 3-wire Single element 4-wire Dual element 3-wire Series 65 RTD terminal block termination (Code 2) Single element 3-wire Single element 4-wire Dual element 3-wire Red Red White Red Red White White Red Red Green Black Blue Blue White Red Red Red Red White White White White Red Red Red Red

product options and configurations including materials of construction that can be expected to perform well in a wide range of applications. The Rosemount product information presented is intended as a guide for the purchaser to make an appropriate selection for the application. It is the purchaser’s sole responsibility to make a careful analysis of all process parameters (such as all chemical components, temperature, pressure, flow rate, abrasives, contaminants, etc.), when specifying product, materials, options and components for the particular application. Emerson Process Management is not in a position to evaluate or guarantee the compatibility of the process fluid or other process parameters with the product, options, configuration or materials of construction selected. Nominal resistance In accordance with DIN EN 60751, the nominal resistance is defined as follows:  100 Ω RTD at 0 °C  Temperature coefficient α = 0.00385 Ω x °C/Ω), averaged between 0 and 100 °C Limit deviations Tolerance Class A as standard: t = ± (0.15 + 0.002 x t); valid for the temperature range from 0 to +350 °C Lead wire configuration As single element (1Pt 100) with 3 or 4 lead wires or dual element (2Pt 100) with 3 lead wires Response time Less than 12 seconds to reach 63% step change in water flowing at 0.4 m/s Process temperature range -50 to +450 °C The measurement range can be limited by the gasket in the process connection. Ambient temperature Housing without head-mounted transmitter  Metal housings: -40 to +130 °C  Plastic housings: -40 to +85 °C Housing with head-mounted transmitter  -40 to +85 °C Maximum process pressure Lower maximum pressure can be due to the process connection Pressure ratings at 20 °C:  Tri-Clamp: 10 bar  Weld-in Ball with PEEK-Seal: 6 bar  Weld-in Ball with SST-Seal: 40 bar  Threaded: 40 bar  Tapered Union with Coupling Nut: 10 bar  VARIVENT: 10 bar Shock and vibration resistance According to DIN EN 60751: 2.8 g peak / 10…500 Hz Self heating 0.15 °K/mW when measured per method defined in DIN EN 60751 Insulation resistance 1,000 MΩ minimum insulation resistance when measured at 500 Vdc and at room temperature Sheath material 321 Stainless Steel with mineral-insulated cable construction Lead wire PTFE insulated, silver coated copper wire

Ingress Protection (IP) ratings The particular rating is applicable only for complete assemblies including a connection head and tubular thermowell. IP varies from 65 to 68 due to a wide selection on different connection heads, DIN A and B size, made of different materials such as aluminum, polyamide, and stainless steel. System components Sensor The 65Q sensor consists of an exchangeable mineral-insulated measuring insert, wherein a small, drop-form thin film RTD element is encapsulated. This design protects the relatively strain-free element, thereby maintaining accuracy and long-term stability. The sensor is mounted into a swaged or straight stainless steel sheath. The sensor outer diameter is 3.2 mm. The minimum sensor length for an exchangeable sensor is 100 mm. The RTD sensor is fitted into a housing with connection head and welded thermowell. Extension  Standard material Stainless Steel 1.4404 (316 L)  Standard diameter of 10 mm  Preferred standard lengths; 50, 65, and 130 mm Thermowell Thermowell stem styles  Straight thermowell with an outer diameter of 6 mm diameter must be used for immersion lengths less than 50 mm  More stable Stepped Thermowell with an outer diameter of 10mm reduced to 6 mm must be used for immersion lengths greater than 50 mm (65 mm on parallel thread G1/2-in. (1/2-in. BSPF)) Thermowell materials  Stainless Steel 1.4404 (316L) for hygienic applications Thermowell surface qualities  Ra < 0,8 μm as standard, electropolishing  Ra < 0,4 μm optional, electropolishing Connection heads (see Table 2) The connection heads can be of different types (size DIN A and B) and materials (plastic, aluminum, stainless steel). Its fitting to the rest of the probe and the gland for the cable entry, assure an IP grade of 65 at minimum. All supplied heads have a process connection M24x1.5. Polished stainless steel DIN A (sanitary applications)  Smoothly contoured design which minimizes crevices for easy wipe-down  Sanitary Stainless Steel housing for easy-to-clean applications  Mounting of one DIN A or B sized transmitter on DIN plate  Local indication with integral LCD Display Meter Polished stainless steel DIN B (sanitary applications)  Smoothly contoured design which minimizes crevices for easy wipe-down  Sanitary Stainless Steel housing for easy-to-clean applications  Mounting of one DIN B sized transmitter on DIN plate Rosemount aluminum DIN A  Rosemount design  Mounting of one or two transmitters on DIN plate and for second one optional by the use of extension ring TZ-A/BL (BUZH)  DIN B head with enlarger space for mounting a DIN A size (644H) or DIN B size transmitter into the cover by the use of terminal block or two transmitters with flying lead sensors GR-A/BL (BUZ)  DIN B head with enlarger space for mounting a DIN A size (644H) or DIN B size transmitter on DIN plates TZ-A/BK  DIN B head with enlarger space for mounting a DIN A size (644H) or DIN B size transmitter into the cover by the use of terminal block or two transmitters (248H) with flying lead sensors  Suggested for use in high humidity environments and at low temperatures to avoid problems due to condensation

Type Material IP rating Lid version Transmitter mounting Conduit connection LCD display meter cover Polished DIN A SST 68 Threaded DIN plate, 644, 248 M20 x 1.5, 1/2-in. NPT Yes Polished DIN B SST 66 Threaded DIN plate, 248 M20 x 1.5, 1/2-in. NPT No Rosemount Aluminum 68 Threaded DIN plate, 644, 248 M20 x 1.5, 1/2-in. NPT Yes TZ-A/BK Polyamide 65 Screw-on cap On cover, terminal block 644, 248 M20 x 1.5 No TZ-A/BL Aluminum 65 Screw-on camp On cover, terminal block 644, 248 M20 x 1.5 No GR-A/BL Aluminum 65 Screw-on camp DIN plate, 644, 248 M20 x 1.5 No

Achieving absolute control through every step of the manufacturing process is essential in order for the production of sanitary fittings to be successful. By achieving such control, each fitting will perform more satisfactorily when incorporated into the process installation, reducing installation time, and ensuring process integrity.  Process connections are available in several sizes  Process connection is continuously welded on the thermowell in such a way to obtain a welding radius of 3.2 mm at minimum, between the lower surface of the connection and the sensor stem according to 3A standards  All process connections are available in material 1.4404 (316L)  Surface roughness on wetted parts: Ra of ≤ 0.8 μm is available as standard, optional with Ra ≤ 0.4 μm, both electropolishing Tri-Clamp  Welded on the thermowell it allows immersion lengths from 25 to 500 mm, they depend on pipe nominal size used; see details on dimension table  Available in 1/2 -to-4 in. (19 to 10.16 mm) tube OD sizes, larger sizes than 4-in. are available upon request  Available in material 1.4404 (316L), surface finish Ra of ≤ 0.8 μm is available as standard, optional with Ra of ≤ 0.4 μm, both electropolishing  Can be cleaned in place, fast and easy to take down, provide lead-tight connections and readily adaptable to other forms of piping, allow in-line temperature measurement by the use of counter part and suitable seal O-ring on customer site  Meet the 3-A Sanitary Standard  Meets ASME BPE 2002 standards Tapered union with coupling nut according to DIN 11851 (dairy connection)  Immersion lengths from 25 to 500 mm  Available in DN10 - DN50 tube OD sizes, larger sizes than 50 DN are available upon request  Available in material 1.4404 (316L), surface finish Ra of ≤ 0.8 μm is available as standard, optional with Ra of ≤ 0.4 μm, both electropolishing  Self-centering, external coupling nut can be easily cleaned 26 N U T D T1 D = Process Connection Diameter T1 = Extension Outer Diameter T = Thermowell Outer Diameter U = Immersion Length N = Extension Length Dimensions (mm) Nominal size D T T1 1/2-in. (12.7 mm) 24.9 6(1) (1) Diameter 6 mm as standard for immersion length U ≤ 50 mm. For U ≥ 50 mm Stepped thermowell diameter 10 mm with reduced measuring tip of 6 mm. 10 3/4-in. (19 mm) 24.9 6(1) 10 1-in. (25.4 mm) 50.4 6(1) 10 11/2-in. (38 mm) 50.4 6(1) 10 2-in. (50.8 mm) 63.9 6(1) 10 21/2-in. (63.5 mm) 77.4 6(1) 10 3-in. (76.2 mm) 90.9 6(1) 10 4-in. (101.6 mm) 119.1 6(1) 10 Dimensions (mm) Nominal size D B T T1 DN 10 22.5 38 6(1) (1) Diameter 6 mm as standard for immersion length U ≤ 50 mm. For U ≥ 50 mm Stepped thermowell diameter 10 mm with reduced measuring tip of 6 mm. 10 DN 25 44 63 6(1) 10 DN 32 50 70 6(1) 10 DN 40 56 78 6(1) 10 DN 50 68.5 92 6(1) 10 26 N U T1 T D B D = Process Connection Diameter T = Thermowell Outer Diameter T1 = Extension Outer Diameter UP = Immersion Length (parallel) UT = Immersion Length (tapered) NP = Extension Length (parallel) NT = Extension Length (tapered)

 Immersion lengths from 25 to 500 mm, mostly used for temperature measurement in vessels  Available in material 1.4404 (316L), surface finish Ra of ≤ 0.8 μm is available as standard, optional with Ra of ≤ 0.4 μm, both electropolishing  Used for Food and Beverage applications  Available with PEEK or SST seal Threaded process connection  Immersion lengths from 25 mm (tapered threads) and 40 mm (parallel threads) to 500 mm  Available in material 1.4404 (316L)  Used for temperature measurement in non-hygienic processes VARIVENT process connection  Immersion lengths from 35 to 500 mm  Available in D = 68 mm  Suitable for hygienic and aseptic applications PARALLEL 26 NP UP T T1 TAPERED 26 NT UT T T1 26 N T D U D = Process Connection Diameter T = Thermowell Outer Diameter U = Immersion Length N = Extension Length Dimensions (mm) T T1 6(1) (1) Diameter 6 mm as standard for immersion length UT ≤ 50 mm or Up ≤ 65 mm. For UT ≥ 50 mm or Up ≥ 65 mm Stepped thermowell diameter 10 mm with reduced measuring tip of 6 mm. 10 Dimensions (mm) Nominal size D DN 32 - 125 68 26 N U 6 25 U = Immersion Length (adjustable) N = Extension Length (adjustable)

pipes or vessels. The counterparts for the process connections and the respective gaskets or sealing rings are generally not supplied with the sensors, and are on the customer's responsibility (FDA material certification, EHEDG and 3A requirements shall be observed). As a general rule, the sensors should be installed in a manner which does not adversely affect their ability to be cleaned. The immersion length may have an influence on the accuracy of the sensors, If it is too short, an error might be generated in the measured temperature, due to the lower temperatures of the process medium near the walls and the heat transfer which occurs through the sensor stem. To avoid this effect of inaccuracy, the immersion length should be, if possible, at least 90 to 120 mm. In pipes with smaller diameter, the axis line of the duct must be reached, and even slightly exceeded by the sensor tip. In hygienic applications a strict installation rule exists so as not to leave any dead spaces along the run of process fluid. In case of disassembling of the sensor, new gaskets equal to the originals and specific torques must be employed for the reassembly procedure, to assure the stated IP grade of the connection heads. TriClamp Flange partially fulfills this requirement. For Weld-in Ball Connection, care should be taken by the user in the execution of the welding on the process side; e.g. suitable weld material, welding radius > 3 mm, absence of pits, crevices etc.) Tapered Union with Coupling nut according to DIN 11581 (Dairy Process Connection) process connection doesn't meet as harsh aseptic requirements as requested for BioPharm applications. Alternatively, for direct insertion into non-hygienic processes, the Series 65Q Temperature Sensor can be ordered with optional G1/2-in. (1/2-in. BSPF) or NPT thread mounting. Figure 2. Installation Drawing h

DIN A SST Codes, E, F, 5, 6 DIN B Polished SST Codes R, S TZ-A/BL Aluminum Code L FR-A/BL Aluminum Code J TZ-A/BK Polyamide Code T 40 25 25 25 25 25 Sensor Lead Wire Terminations Flying leads Code 0 Terminal block Code 2 3.2 L L 3.2

Thermowells and Process Connections Tri-Clamp Weld-in ball (adjustable) Tapered union with coupling nut Threaded tapered Threaded parallel Stepped thermowell Straight thermowell VARIVENT

The Emerson logo is a trade mark and service mark of Emerson Electric Co. Tri-Clamp, Rosemount, and the Rosemount logotype are registered trademarks of Rosemount Inc. VARIVENT is a registered trademark of GEA Process Engineering Limited. All other marks are the property of their respective owners. © 2014 Rosemount Inc. All rights reserved. Emerson Process Management Rosemount Inc. 8200 Market Boulevard Chanhassen, MN 55317 USA T (U.S.) 1-800-999-9307 T (International) (952) 906-8888 F (952) 906-8889 www.rosemount.com Emerson Process Management Blegistrasse 23 P.O. Box 1046 CH 6341 Baar Switzerland T +41 (0) 41 768 6111 F +41 (0) 41 768 6300 www.rosemount.com Emerson Process Management Asia Pacific Pte Ltd 1 Pandan Crescent Signapore 128461 T +65 6777 8211 F +65 6777 0947 Service Support Hotline: +65 6770 8711 Email: [email protected] www.rosemount.com Rosemount 65Q 00813-0100-4827 Rev DA Product Data Sheet September 2014 Emerson Process Management Latin America 1300 Concord Terrace, Suite 400 Sunrise, Florida 33323 USA T + 1 954 846 5030 www.rosemount.com