B&B Electronics EIS Series Installation Manual

International Headquarters: 707 Dayton Road PO Box 1040 Ottawa, IL 61350 USA 815-433-5100 Fax 433-5104 www.bb-elec.com [email protected] [email protected] European Headquarters: Westlink Commercial Park Oranmore Co. Galway Ireland +353 91 792444 Fax +353 91 792445 www.bb-europe.com [email protected] [email protected] PRODUCT INFORMATION B&B ELECTRONICS Ethernet Media Converter & Rack Chassis 100BaseFX Connections: The Tx (transmit) port of device 1 is connected to the Rx (receive) port of device 2, and the Rx (receive) port of device 1 to the Tx (transmit) port of device 2. Description The media converter provides one channel for media conversion between 10/100BaseTX and 100BaseFX. It can be used as a stand- alone device or with a standard 19 inch chassis as shown below. Features y One-channel media conversion: 10/100BaseTX & 100BaseFX y Fiber media: Multi-mode fiber using SC or ST connectors Single-mode fiber using SC connectors y Auto negotiation of speed and duplex mode on TX port y Auto MDIX on TX port y DIP switch configuration for: Link-fault-pass-through Fixed speed Half/full duplex y Store-and-forward mechanism y Non-blocking full wire-speed forwarding rate y Supports broadcast storm filtering y Back-pressure & IEEE802.3x compliant flow control y Front panel status LEDs y External AC to DC power adapter (included) y Used as a stand-alone device or with a chassis y Hot-swappable when used with a chassis 10/100BaseTX and 100BaseFX Connectors 10/100BaseTX Connections: Pin Regular Ports Uplink Port 1 Receive Data + (input) Transmit Data + (output) 2 Receive Data – (input) Transmit Data – (output) 3 Transmit Data + (output) Receive Data + (input) 4 NC NC 5 NC NC 6 Transmit Data – (output) Receive Data – (input) 7 NC NC 8 NC NC LED’s and DIP Switch LED Status: LEDs State Indication Steady Power on (PWR stands for POWER) PWR Off Power off Steady 100Mbps network connection 100 Off 10Mbps network connection Steady Network connection established(LNK stands for LINK) Flashing Transmitting or receiving data(ACT stands for ACTIVITY) LNK/ACT Off Neither a network connection established nor transmitting/receiving data Steady Connection in full duplex mode(FDX stands for FULL-DUPLEX) Flashing Collision occurred(COL stands for COLLISION) FDX/COL Off Connection in half-duplex mode DIP Switch Settings: Pos. DOWN (0) UP (1) 1 Enable Link-fault-pass-through Disable Link-fault-pass-through 2 RJ45 Auto Negotiation Enabled RJ45 Forced Mode 3 RJ45 Forced to 100Mbps RJ45 Forced to 10Mbps 4 RJ45 Forced to Full Duplex RJ45 Forced to Half Duplex 5 Fiber Forced to Full Duplex Fiber Forced to Half Duplex 6 This quick installation guide describes how to install and use the Ethernet Media Converter and optional Rack Chassis.

International Headquarters: 707 Dayton Road PO Box 1040 Ottawa, IL 61350 USA 815-433-5100 Fax 433-5104 www.bb-elec.com [email protected] [email protected] European Headquarters: Westlink Commercial Park Oranmore Co. Galway Ireland +353 91 792444 Fax +353 91 792445 www.bb-europe.com [email protected] [email protected] PRODUCT INFORMATION B&B ELECTRONICS Link-fault-pass-through Link-Fault-Pass-Through Overview: When two Media Converters are connected via their fiber ports Link Fault of the FX port: A Link Fault condition will be sensed on the RJ45 port whenever the media converter detects a Link Fault condition on the Fiber port. (The 100, LNK/ACT, and FDX/COL LED’s will be off.) Link Fault of the TX port: Media Converter A: A Link Fault condition will be sensed on the Fiber port whenever the media converter detects a Link Fault condition on the RJ45 port. Thus, the 100, LNK/ACT, and FDX/COL LEDs of the RJ45 port of the Media Converter A would be off. Media Converter B: A Link Fault condition will be informed to the Fiber port of the Media Converter B. Then a Link Fault condition will be sensed on the RJ45 port of the Media Converter B whenever the Media Converter B detects a Link Fault condition on the Fiber port. Thus, the 100, LNK/ACT, and FDX/COL LEDs of the Media Converter B would be off. Link Fault of the FX port TX Port FX Port LEDs PWR 100 LNK/ACT FDX/COL LNK/ACT FDX/COL Media Converter A ON OFF OFF OFF OFF OFF Media Converter B ON OFF OFF OFF OFF OFF Link Fault of the TX port TX Port FX Port LEDs PWR 100 LNK/ACT FDX/COL LNK/ACT FDX/COL Media Converter A ON OFF OFF OFF ON ON Media Converter B ON OFF OFF OFF OFF OFF Rack Chassis Specifications Features: • House up to 16 media converters • Front panel LED’s for power status • Standard 19 inch Rack, 2U size • Hot-swappable: Media converters and Power supplies • Cooling fans for ventilation - one on right & left sides of chassis • Ventilation holes on each side • Load sharing mechanism: If one power supply fails, the other takes over immediately • Each converter bay is electrically isolated from each other • Over current protection Fuses on PCB for each converter bay Fuses on each power supply Chassis Specifications: Capacity Houses up to 16 media converters Power One power supply included, second optional hot-swappable Cooling One fan on the left and right side of the chassis LED Indicators One LED for each power supply’s power status) Dimensions 17.3 x 10.9 x 3.5 in (44 x 27.6 x 9 cm) Standard 19 inch, 2U size Net Weight 8.5kg approx. (with sixteen media converters) Power Supply Specifications: Power Input 110 to 240VAC, 50/60Hz Power Output 12VDC, 84W max. Load 7A max. Operating Temp 0°C to 40° C (32°F to 104°F) Storage Temp -25°C to 70°C (-13°F to 158°F) Emissions FCC Part 15 Class A; CE Class A Installation Connecting Power: The media converter is a plug-and-play device, so simply plug the power supply into the converter and then the AC outlet. Installing the Media Converter into the Chassis: The media converter fits into any of the chassis expansion slots. y First, remove one of the expansion slot carriers y Then, install the converter onto the carrier y Next, insert the carrier onto the guide rails of the expansion slot y Carefully slide the carrier unit in, until it firmly fits the chassis y Reinstall the screw that locks the carrier to the chassis Installing the Power Supply into the Chassis: The power supply fits into either of the two power supply bays on the back of the rack chassis. y First, remove the cover plate y Then, insert the power supply into the guide rails of the bay y Carefully slide the power supply in until it firmly fits in the chassis y Tighten the thumb screws provided on the power supply Media Converter Specifications Media Converter Specifications: Applicable Standards IEEE 802.3 10BaseT, IEEE 802.3u 100BaseTX & 100BaseFX Fixed Ports (1) TX port, (1) FX port 10/20Mbps for half/full-duplex Speed 10BaseT 100BaseTX/FX 100/200Mbps for half/full-duplex Switching Method Store-and-Forward Forwarding rate 14,880/148,800pps for 10/100Mbps Cable 10BaseT 100BaseTX 100BaseFX 2-pair UTP/STP Cat. 3, 4, 5 up to 100m 2-pair UTP/STP Cat. 5 up to 100m MMF (50 or 62.5µm), SMF (9 or 10µm) Per Unit - PWR1, PWR2, FAULT, LFP LED Indicators Per Port - TX: LNK/ACT, FDX/COL, 100 FX: LNK/ACT, FDX/COL Dimensions 4.3 x 3.2 x 0.9 in. (10.9 x 8 x 2.4 cm) Weight 0.15 Kg Power External Power Supply 12VDC @ 280mA Power Consumption 3.4W Operating Temperature 0°C to 50°C Storage Temperature -25°C to 70°C Humidity 10 to 90%, non-condensing Emissions FCC Part 15, Class A; CE Safety UL/CUL 60950, EN60950, IEC 60950, IEC61000-6-2