Bay Tek Games Big Bass Wheel Pro Service Manual

THE MONITOR. B. FAULTY MONITOR. A. ENSURE POWER IS PLUGGED INTO THE BACK OF THE MONITOR DOWN TO THE POWER STRIP. B. REPLACE MONITOR (A5CBDI030). ERROR ON SCREEN AFTER POWER UP. (RE-BOOT GAME TO SEE IF THE PROBLEM REPEATS.) A. DISPLAY STOPS AT "NO BOOTABLE DEVICE--INSERT BOOT DISK AND PRESS ANY KEY". B. DISPLAY SHOWS "PUPPY VIDEO WIZARD" OR "Xorg". C. DISPLAY SHOWS "KERNEL PANIC- UNABLE TO MO ...

MONITOR. A. TICKET STACK NOT RESTING PROPERLY ON THE LOW TICKET SWITCHES. B. FAULTY LOW TICKET SWITCH. C. FAULTY WIRE OR CONNECTION. D. FAULTY I/O BOARD. A. ADJUST THE TICKET STACK SO THEY HOLD THE SWITCH DOWN. B. REPLACE LOW TICKET SWITCH (A5SW200). C. CHECK FOR PROPER CONNECTION FROM THE SWITCH TO THE I/O BOARD. D. REPLACE I/O BOARD (AACB1900). BAY TEK GAMES, INC. BBW-PRO SERVICE MANUAL Page 42 ...

TOTAL CREDITS SHOWS THE AMOUNT OF CREDITS IN QUEUE WAITING TO BE PLAYED. TICKETS LEFT TO DISPENSE SHOWS THE AMOUNT OF TICKETS THAT ARE WAITING TO BE DISPENSED. SOFTWARE VERSION SHOWS THE CURRENT INSTALLED SOFTWARE VERSION NUMBERS BAY TEK GAMES, INC. BBW-PRO SERVICE MANUAL Page 32 ...

ATTENTION If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent. ATTENTION Always plug this game into a grounded circuit. ATTENTION Be sure the electrical power matches the game requirements. See the serial number decal located on the back of the game cabinet. All Bay Tek games are 110V unless specifically ordered 220V. The game will draw 2-3 AMPS at start up. Outlets should be rated for 20 AMPS or higher. The game voltage can be found on the serial number decal, see below. ...

ADD 3 MONTHS TO THE WARRANTY OF THIS GAME BY COMPLETING AND SUBMITTING THIS FORM BY FAX OR MAIL. NEW GAME REGISTRATION www.baytekgames.com Pulaski, WI 54162 Fax: 920.822.8936 Phone: 920.822.3951 Game Owner/Operator E-Mail Address: Game Location Name and Address: Bay Tek Games Inc. 1077 East Glenbrook Dr. Game Name (one game per form): Date: Game Serial Number (located on the back of the cabinet): Game Owner/Operator Company Name: Game Owner/Operator Address: Game Owner/Operator City/State/Zip: Game Owner/Operator Phone Number: Gam ...

1 Our Vision 2 Door Open Warning 29 Our Mission 2 Motor Watchdog Error 29 Our Values 2 Software Version 30 Our Other Exciting Products 3 Total Credits 30 Installation Information 4 Tickets Left to Dispense 30 Service First Network 5 Wheel Position 31 About Big Bass Wheel Pro™ 6 Inputs and Outputs 31 Game Measurements 7 Brake Status 31 Safety Precautions 8 Wheel Speed 32 Inspecting the Game 10 Service Connections 11 Total Games 33 Power Requirements 11 Total Tickets 33 Setting Up Your Game 12 Tickets per Game 33 Key Components 16 Total Motor Assist' ...

OPEN LEFT FRONT DOOR AND PRESS THE "MENU BUTTON" TO ENTER THE OPERATOR MENU. CHECK VALUE ON THE MONITOR AGAINST WHERE THE WHEEL IS. IF THE VALUES DO MATCH (FIG. 1): 1. LOOK FOR THE "MOTOR WATCHDOG ERROR". SEE PAGE 31. 2. ENCODER SENSOR NOT READING PROPERLY. GO TO THE "ENCODER WHEEL SENSOR", PAGE 53, TO ADJUST. REPLACE IF NEEDED (AACB1901). IF THEY DO NOT MATCH (FIG. 2): MANUALLY SPIN THE WHEEL ONE COMPLETE REVOLUTION TO ENSURE THE HOME SENSOR IS BEING READ. IMPORTANT: ALWAYS SPIN DOWNWARDS! ENCODER SENSOR SIGNAL NOT REACHING I/O BOARD 1. CHECK THE CABLE ...

Bay Tek Games warrants to the original purchaser that the game will be free of defects in workmanship and materials for a period of 6 months from the date of installation. Register your new game for an extra 3 months on your warranty. See page 1 for registration information. Bay Tek Games will, without charge, repair or replace at it's option defective product or component parts upon notification to the parts/service department. Warranty replacement part(s) will be shipped immediately via ground service, along with a Return Material Authorization ...