Altronix eBridge4PCRM Installation Manual

Rev. 032113 I.T.E. 43KC eBridge4PCRM IP and PoE+ over Coax Solution Operates with eBridge1PCTX Transceiver or eBridge1ST Mini Transceiver Installation Guide Z1409 PLUS

eBridge4PCRM Overview: Altronix eBridge4PCRM and eBridge1PCTX or eBridge1ST are CAT5 to Coax cable Ethernet adapters/Media converters that deliver data and power over the coax cable in a PoE+ compliant format. The paired set enables fast 10/100Base-T Ethernet digital communication to be transmitted over Coax cable. eBridge4PCRM receiver is powered by a UL Listed limited power source, PoE midspan or endspan product, such as a NetWay8M and NetWay16M, and sends its power over the coax to the eBridge 1PCTX or eBridge1ST transmitter under PoE protocol. This enables eBridge4PCRM to be used in a managed manner, allowing for remote camera reset. eBridge1PCTX or eBridge1ST, in turn, delivers that PoE+ compliant power to a PoE enabled camera or IP device. eBridge4PCRM will not deliver power to non-compliant devices, thus avoiding damage to improperly connected analog cameras. These plug and play units facilitate system upgrades from analog to IP cameras/ devices utilizing existing legacy Coax and eliminating the costs and labor associated with installing new net- work cabling. In addition, data transmission and power over the Coax is possible up to 500m in comparison to 100m Ethernet maximum distance (see Maximum Length of Coax Type vs. Camera Power/PoE Class, pg. 6). A maximum range from head end to the PoE camera/device is 700m, taking into consideration that up to 100m of structured cable may be deployed at each end. Features: Agency Listings: • UL 60950-1 Information Technology Equipment. • CE European Conformity. • C-Tick C-Tick compliant. Compatible Transceivers: • eBridge1PCTX: PoE/PoE+ compliant transceiver. • eBridge1ST: PoE/PoE+ compliant mini transceiver. Input: • Powered by a UL Listed limited power source, PoE midspan or endspan. Ethernet: • Connectivity: RJ45, auto-crossover. • Wire type: 4-pair CAT5 or better structured cable. • Distance: up to 100m. • Speed: 10/100BaseT, half/full duplex, auto negotiation. PoE compliant to IEEE 802.3af (15W) and PoE+ compliant to IEEE 802.3at (30W) delivered to camera by eBridge1PCTX or eBridge1ST. Power provided by eBridge4PCRM to eBridge1PCTX or eBridge1ST by PoE protocol. • Throughput is rated to pass 25Mbps of data at distances up to 500m. With proper headend equipment this supports Megapixel, HD720, HD1080. Coax: • Distance: up to 500m (see Maximum Length of Coax Type vs. Camera Power/PoE Class, pg. 6) for power delivery of coax. • Connectivity: BNC, RG-59/U or similar. LED Indicators: • eBridge4PCRM: Blue LED - Coax link connection. Green - PoE ON. Green - Power ON. • eBridge4PCRM and eBridge1PCTX: Yellow and Green LED (RJ45) IP Link status, 10/100Base-T/active. • eBridge1PCTX and eBridge1ST: Blue LED - Coax link connection. Green LED - PoE from eBridge4PCRM. Environmental: • Operating Temperature: eBridge4PCRM: –20ºC to 49ºC (–4ºF to 120.2ºF). eBridge1PCTX: For 15W: –40ºC to 75ºC (–40ºF to 167ºF). For 30W: –40ºC to 49ºC (–40ºF to 120.2ºF). eBridge1ST: For 15W: –40ºC to 75ºC (–40ºF to 167ºF). For 30W: –40ºC to 65ºC (–40ºF to 149ºF). • Storage Temperature: –30º to 70ºC (–22º to 158ºF). • Humidity: 20 to 85%, non-condensing. Functions: • Auto detection and protection of legacy non-PoE cameras/devices. Applications: • Retrofit digital IP cameras in an analog CCTV installation. • Works with Megapixel, HD720, HD1080 and VGA (SD) cameras (see note, pg. 2). • Extend Network link distance in an industrial environment over 700m (see note, pg. 2). • Upgrade deployed CCTV Coax to a digital network in Retail, Hospitality, Arenas, Casinos, Airports, Schools, Hospitals, Transportation, etc. Mechanical: • Dimensions (H x W x D approx.): eBridge4PCRM dimensions: 1.7” x 5.23” x 8.42” (43.2mm x 132.8mm x 213.9mm) eBridge1PCTX dimensions: 1” x 2.5” x 4.375” (25.4mm x 63.5mm x 111.1mm). eBridge1ST dimensions: 2.27” x 2.645” x 1.12” (57.7mm x 67.2mm x 28.4mm).

­Installation Instructions: Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction. Wiring should be UL Listed and/or Recognized wire suitable for the application. eBridge1PCTX, eBridge1ST, and eBridge4PCRM are not intended to be connected to outside plant leads and should be installed indoors within the protected premises. eBridge1PCTX, eBridge1ST, and eBridge4PCRM are intended for indoor use only. 1. eBridge4PCRM installation: a. Affix rubber pads to eBridge4PCRM for shelf installation (Fig. 5, pg. 8). Unit should be mounted in proximity to ethernet switch/network, NVR or video server. b. Connect structured cable from ethernet midspan or endspan device to RJ45 jack marked [10/100BaseT] (Fig. 2, pg. 4). c. Connect Coax cable to BNC connector marked [Coax] (Fig. 1, pg. 3). 2. eBridge1PCTX installation: a. Secure unit to desired mounting surface with a proper fastening device utilizing the case’s mounting hole. Unit should be mounted in proximity of camera/device. b. Connect structured cable from IP camera/device to RJ45 jack marked [10/100BaseT] (Fig. 2, pg. 4). c. Connect Coax cable to BNC connector marked [Coax] (Fig. 2, pg. 4). 3. eBridge1ST installation: a. Secure unit to the desired mounting surface with a proper fastening device utilizing the case’s mounting hole (Fig. 3, pg. 4). Unit should be mounted in proximity of camera/device. b. Connect structured cable from IP camera/device to RJ45 jack marked [PoE Out] (Fig. 3, pg. 4). c. Connect Coax cable from eBridge4PCRM to BNC tether cable marked [Coax] (Fig. 3, pg. 4). Note: eBridge4PCRM is designed to accommodate Megapixel, HD720, HD1080 and VGA (SD) cameras. It is important to note that some high resolution and high frame rate cameras may demand faster headend processing ability, such as a PC graphics card to present a quality image. If the headend processing equipment is insufficient in speed, the image may show pixelation and latency. It is advisable to pre-test system if unsure. Alternatively, frame rate and resolution may be reduced to accommodate system equipment. Fig. 1 eBridge4PCRM 10/100 Base-T Structured Cable from midspan/endspan Data In Coax Cable from eBridge1PCT or eBridge1PCTX Front Panel Back Panel

eBridge4PCRM Green LED indicates Power Structured Cable from IP Camera/Device Blue LED indicates Coax Connection Coax Cable from eBridge4PCRM Fig. 2 eBridge1PCTX Fig. 3 eBridge1ST Front Rear Structured Cable from Camera/Device Green LED indicates PoE Out to Device Flying BNC Connector Blue LED indicates Coax Link is active Flying BNC Connector Technical Specifications: Parameter Description Connections BNC for Coax link. RJ45 for ethernet link. Input power requirements Midspan or endspan port connected. Indicators Blue: Coax Link. Yellow (RJ45 connector): On - Link, Off - No Link, Blinking - Activity. Green (RJ45 connector): On - 100Base-TX, Off - 10Base-T. Green: Power. Environmental Conditions Operating Ambient Temperature: UL60950-1 eBridge4PCRM: -20ºC to 49ºC (-4ºF to 120.2ºF). eBridge1PCTX: For 15W: -40ºC to 75ºC (-40ºF to 167ºF). For 30W: -40ºC to 49ºC (-40ºF to 120.2ºF). eBridge1ST: For 15W: -40ºC to 75ºC (-40ºF to 167ºF). For 30W: -40ºC to 65ºC (-40ºF to 149ºF). Storage Temperature: -30ºC to 70ºC (-22ºF to 158ºF). Relative Humidity: 20 to 85%, non-condensing. Operating Altitude: -304.8 to 2,000m. Regulatory Compliance UL/CUL Listed for Information Technology Equipment (UL 60950-1). CE approved. C-Tick compliant. Weights (approx.) Product: 1.35 lbs. (0.61 kg) | Shipping: 1.7 lbs. (0.77 kg)

PoE Camera PoE Camera PoE Camera PoE Camera PoC (PoE+ over Coax) 500m max. PoC (PoE+ over Coax) 500m max. PoC (PoE+ over Coax) 500m max. PoC (PoE+ over Coax) 500m max. 100m max. 100m max. 100m max. 100m max. PoE compliant 100m max. PoE compliant 100m max. PoE compliant 100m max. PoE compliant 100m max. Coax Structured Cable Legend: Transceiver eBridge4PCRM Powered Switch or NetWay MidSpan Transceiver Transceiver Transceiver Multiple PoE Camera Connection: Fig. 4

eBridge4PCRM Maximum Length of Coax Type vs. Camera Power/PoE Class: Camera Power/ PoE Class Coax Type RG59/U - 23AWG RG59/U - 22AWG RG59/U - 20AWG RG59/U - 18AWG RG6/U - 18AWG Max. Length (meters) 13W/0 261 336 500 500 500 4W/1 500 500 500 500 500 6.5W/2 500 500 500 500 500 13W/3 261 336 500 500 500 19W 153 199 316 500 500 25W 119 152 240 366 366

eBridge4PCRM Altronix is not responsible for any typographical errors. 140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056 website: www.altronix.com | e-mail: [email protected] | Lifetime Warranty | Made in U.S.A. IIeBridge4PCRM F20R MEMBER C Mounting Hardware (Included): Four (4) rubber pads Rubber Feet Left side B A C Fig. 5 eBridge4PCRM Chassis Mechanical Drawing & Dimensions (H x W x D approx.): 1.7” x 5.23” x 8.42” (43.2mm x 132.8mm x 213.9mm) Shelf Installation 1- Position and affix rubber pads (C) (included) at each corner on the bottom of the unit (Fig. 6). 2- Place unit in desired location. 10/100 Base-T 5.23” (132.8mm) 8.42” (213.9mm) 1.7” (43.2mm) 8.93” (226.8mm)