Ancona Villa Manual 

G P M 0 10 20 30 40 50 60 70 80 0 1 5 1 1 5 2 Single Handle Pull-out Kitchen Faucet STANDARDS - LISTED IAPMO/cUPC Gather the necessary tools as shown below to complete the installation of this faucet. Some may not be needed depending on the model of faucet you are installing. Check with your local hardware store on the requirements of your installation situation. Tools: PLUMBERS PUTTY FLASHLIGHT BASIN WRENCH SAFETY GLASSES SCREWDRIVER PLIERS CHANNELLOCKS ADJUSTABLE WRENCH HEX-KEY TAPE For easy installation, you will need: - To read all the installation instructions completely before beginning. - To read all the warning, attention and maintenance information. - To purchase the proper supply lines. Tighten connection with two wrench to prevent damage to tube body. Be careful not to bend the stem as this will void the product warranty. Attention: Helpful Information Flow Rate Chart Important Villa 2018-06-22 MAAN4113-1 SEALED-TUBE WARNING: Please keep the tools for future use!

gasket in order on the counter top as shown. Don't forget the O-ring. Assemble gasket assembly and lock nut to faucet threaded sleeve by hand and tighten the screws with screwdriver. 2 Connect the shower hose to quick connect. CAUTION: MAKE SURE THE HOSE IS PROPERLY ENGAGED AND SECURED IN THE QUICK CONNECT. Disassemble the weight and put it on the shower hose. Then fix screws by screw driver. Tools might be applied to the following places: Installation size map 11.6" (294.2 mm) 10.4" (264.2 mm) 4" (103 mm) 18.8" (479 mm) 3.5" (89.6 mm) 8" (204.7 mm) Ø1.3" (35 mm) Ø1.3-1.5" (35-38 mm) Ø1.3" (35 mm) Ø1.3-1.5" (35-38 mm) 9.2" (234 mm) 11.4" (289.3 mm) Ø1.2" (30 mm) 1/2-14NPSM 1/2-14NPSM M15X1

B. Turn on water supplies. Check connections for leaks. C. Remove hand shower and let both hot and cold water run for one minute. This will help clean any debris that might otherwise clog the system. Replace hand shower. D. Operate handle up and down, in cold and hot positions, to flush water lines thoroughly. Checking and Testing Test Faucet Installation Simply rinse the surface with clear water or mild liquid detergents if necessary Dry the faucet with a clean soft cotton cloth Do not use any cleaning agents containing acids polish abrasives or harsh cleaners Maintenance: 3 A. B. C. Connect to water supply lines with either A 3 8 O D copper tubing ball nose risers with the coupling nuts or B 3 8 copper tubing no ball with supplied tube head interior connector or C IPS faucet connectors 1 2"). 4 Remove the shower by hand. Turn the faucet handle all the way on, turn on hot and cold water supply and flush water lines for one minute. Reinstall shower by hand. 5 Check all connections at arrows for leaks and retighten if necessary. BUT DON'T OVERTIGHTEN

2. Clean the product with gentle liquid or glass cleaner. 3. Don't use acid cleaner. 4. Don't clean with abrasive material, abrasive paper or knife. Parts list Cleaning and care Daily cleaning and care are required in order to keep the product shining and working properly. Shower hose Shower sleeve Spout Trim cap Ring Connector Ring Screw Body Cartridge base Cartridge Cartridge locknut Trim cap Handle Screw Index Threaded shank Copper tube(hot water) Copper tube Copper tube(cold water) Quick connect Base O-ring Gasket assembly Lock nut Screw Weight Allen key Base Deck plate Gasket Flexible hose NO. PART NAME Shower 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 8 9 10 11 12 13 14 15 20 21 22 18 4 5 1 2 3 19 29 30 6 7 23 24 25 26 27 28 33 30 31 16 17