Carrier 30XV70000501 Installation Instructions

Catalog No. 04-53300179-01 Printed in U.S.A. Form 30XV-4SI Pg 1 6-17 Replaces: New Installation Instructions Part No. 30XV70000501, 30XV70000601 SAFETY CONSIDERATIONS Installing, starting up, and servicing air-conditioning equip- ment can be hazardous due to system pressures, electrical com- ponents, and equipment locations. Only trained, qualified installers and service technicians should install, start up, and service this equipment. When installing this accessory, observe precautions in the literature and on any labels attached to the equipment, and all other safety precautions that may apply. • Follow all safety codes. • Wear safety glasses and work gloves. • Use care in handling and installing this accessory. INTRODUCTION The accessory condenser hail guard is designed to protect the 30XV chillers from harsh weather conditions and debris. See Table 1 for accessory package usage and see Table 2 for accessory package contents. Check each item for shipping damage. If any damage is found, file a claim with the shipping agent immediately. If any item is missing or if any part does not assemble properly, notify your Carrier representative. Field-Supplied Material — Zinc-rich paint. Table 1 — 30XV Accessory Package Usage *Standard, medium, or high tier is represented by an S, M, or H in the 10th position of the unit model number. CAUTION To avoid the possibility of electrical shock, open and tag all disconnects before installing this equipment. Be aware that there may be more than one disconnect. CAUTION Only trained, qualified installers and service technicians should install, start up, and service this equipment. Untrained personnel can perform basic maintenance func- tions such as cleaning coils. All other operations should be performed by trained service personnel. When working on the equipment, observe precautions in the literature and on tags, stickers, and labels attached to the equipment. CAUTION To avoid damage to the refrigerant coils and electrical com- ponents, use extreme care when drilling screw holes and screwing in fasteners. 30XV UNIT SIZE AND TIER* NO. OF PACKAGE(S) REQUIRED FOR ACCESSORY PART NO. 30XV70000501 30XV70000601 140-Std 1 0 140-Mid 1 0 140-High 1 1 160-Std 1 0 160-Mid 1 1 160-High 1 2 180-Std 1 0 180-Mid 1 1 180-High 1 2 200-Std 1 1 200-Mid 1 2 200-High 1 3 225-Std 1 1 225-Mid 1 2 225-High 1 3 250-Std 1 2 250-Mid 1 3 250-High 1 4 275-Std 1 2 275-Mid 1 3 275-High 1 4 300-Std 1 3 300-Mid 1 4 300-High 1 5 325-Std 1 4 325-Mid 1 5 325-High 1 6 350-Std 1 4 350-Mid 1 5 350-High 1 6 400-Std 1 5 400-Mid 1 6 400-High 1 7 450-Std 1 6 450-Mid 1 7 450-High 1 8 500-Std 1 7 500-Mid 1 8 30XV140-500 Hail Guard Accessory

INSTALLATION NOTE: Numbers in parentheses are item numbers unless indicated. NOTE: Not all panels in kit will be used for every unit size. 1. Disconnect all power to unit. 2. Attach side uprights (1) between each V section on both sides of unit. Use 2 screws at the top and 2 at the bottom of each upright. See Fig. 1. 3. Attach side channel assemblies (2 and 3) horizontally be- tween uprights (1) on sides of chiller. Use channel assem- bly (3) on the end sections and channel assembly (2) in the other locations. Use 4 screws, 2 on each end of each side channel assembly. See Fig. 2. 4. Attach the end channel assembly (4) horizontally to the end of the unit opposite the control box. Use 4 screws, 2 on each end of the end channel assembly. See Fig. 3. ACCESSORY PART NO. DESCRIPTION ITEM NO. QTY 30XV70000601 Side Upright, 30XV50061901 1 6 Side Channel Assembly, 30XV40042601 2 4 Side Channel Assembly, 30XV40042501 3 4 End Channel Assembly, 30XV40036701 4 1 Control Box Angle Support, 30XV40036801 5 1 Control Box Angle Support, 30XV40036901 6 1 Louvered Side End Panel, 30XV50062101 7 4 Louvered Side End Panel, 30XV50062103 8 4 Louvered Side Panel, 30XV50062001 9 4 Louvered Side Panel, 30XV50062002 10 4 Louvered End Panel, 30XV50037601 11 2 Louvered End Panel, 30XV50037602 12 2 End Wire Guard, 30XV50036802 13 1 Louvered End Panel, 30XV50037301 14 1 Louvered End Panel, 30XV50037401 15 1 Louvered End Panel, 30XV50037501 16 1 Screws, 00PPN500000304A 17 284 30XV70000701 Side Upright, 30XV50061901 1 2 Side Channel Assembly, 30XV40042601 2 2 Louvered Side Panel, 30XV50062001 9 2 Louvered Side Panel, 30XV50062002 10 2 Screws, 00PPN500000304A 17 80 IMPORTANT: Hail guard accessory is designed for installa- tion after unit is installed. The upright and lower panels will block the lifting points for the chiller. Fig. 1 — Side Uprights A30-6314 SIDE UPRIGHTS A30-6318 Fig. 2 — Side Channel Assemblies SIDE END CHANNEL ASSEMBLIES SIDE CHANNEL ASSEMBLIES Fig. 3 — End Channel Assembly END CHANNEL ASSEMBLY A30-6319 a30-3619

See Fig. 4. NOTE: Use angle (5) and 2 screws for unit sizes 140 to 200 and angle (6) and 4 screws for unit sizes 225 to 325. Neither support is required for unit sizes 350 to 500. 6. Attach side end panels (7 and 8) to sides of the unit near- est the end at 4 corners using one screw at each clearance hole in each panel. See Fig. 5. NOTE: Item 7 is the top panel and Item 8 is the bottom panel. 7. Attach side panels (9 and 10) to each side of the unit to cover the area between the side end grilles. Use one screw at each clearance hole in each panel. See Fig. 6. NOTE: Item 9 is the top panel and Item 10 is the lower panel. 8. Attach end panels (11 and 12) and end wire guard (13) to the end of unit (opposite the control box). Attach panels with one screw at each clearance hole in each panel. Place screws between grille rods that are spaced closely togeth- er. See Fig. 7. Unit Sizes 140 to 200 a30- 6320 CONTROL BOX ANGLE SUPPORT Fig. 4 — Angle Supports Unit Sizes 225 to 325 a30-6321 CONTROL BOX ANGLE SUPPORT A30-6321 Fig. 5 — Side End Panels A30-6396 SIDE END CHANNEL ASSEMBLIES SIDE CHANNEL ASSEMBLIES Fig. 6 — Side Panels SIDE PANELS A30-6318 A30-6397

Catalog No. 04-53300179-01 Printed in U.S.A. Form 30XV-4SI Pg 4 6-17 Replaces: New © Carrier Corporation 2017 NOTE: Item 11 is the top panel and Item 12 is the lower panel. 9. Piping may exit through the end grille or side grille de- pending on the unit. Cut grille rods as required to provide opening for water lines. Coat ends of cut rods with zinc- rich paint to protect against rust. 10. Attach end panel(s) to the control box end of unit using one screw at each clearance hole in each panel. See Fig. 8. NOTE: Use panel 14 for unit sizes 140 to 200 and panels 15 and 16 for unit sizes 225 to 325. Neither panel is re- quired for unit sizes 350 to 500. NOTE: Item 15 is the top panel and Item 16 is the bottom panel. 11. When all panels are installed and properly fastened, re- store power to unit. Fig. 7 — Louvered End Panels and End Wire Guard A30-6398 LOUVERED END PANELS END WIRE GUARD Fig. 8 — Louvered End Panel 30XV140-325 CONTROL BOX END PANEL(S)