Abus SHGW10000 Manual 

Q U I C K G U I D E ABUS Security-Center • Linker Kreuthweg 5 86444 Affing • Germany • abus.com

Installing the Gateway Supported Smartphone System Version: iOS: iPhone or iPad Requires iOS 6.0 or later Android Smartphone or Tablet Requires Android 4.0 or later Step 1: Download the ABUS Z-Wave One APP Step 2: Add the Gateway Click on the „Add a gateway“ and follow the further instructions in the app. Step 3: Login Press the Gateway icon to log in to the Gateway. Assign a secure administrator access now by entering an admin account name and password. Step 4: Add a Z-Wave Component To add a Z-Wave device into the Gateway (Inclusion), follow the steps below: 1. Set the gateway inclusion mode a. Press "Component" b. Press „+“ c. Choose between ABUS devices or other devices d. Follow the inclusion steps of the respective device 2. When the gateway detects the Z- Wave component, a "Di" tone is output. 3. After you have assigned a name to the component, the gateway confirms the successful inclusion with a success tone. Note: If the inclusion failed, check whether The Z- Wave frequency of the device is the same as of the Gateway (EU). It may be necessary to exclude the device before attempting to include it again. Select the "-" symbol in the component view here and perform the exclusion procedure.

Step 5: Add a new room 1. Press the „Room“ Icon 2. Press „+“ 3. Assing a name After a room has been created, included devices can be added to it. To do this, either go to the room overview and press “+” to add device or assign the room in the device overview. If temperature, humidity and/or brightness sensors have been added to a room, the respective values are displayed as a preview in the room overview. If there are several devices with the same parameter, you can choose which value shall be displayed in the preview. Step 6: Create a new scene Up to 60 scenes can be created on each gateway, each scene consists of IF/THEN/WHEN elements. "IF" is the condition under which the scene is to be triggered, up to 6 conditions per scene are possible. These can be and/or based. The "IF" conditions can be set according to the status of the Z-Wave devices, Smartvest, room conditions or gateway status. "THEN" are the actions of the scene, up to 6 actions are possible per scene. The "THEN" actions can be applied to Z-Wave devices, Smartvest, room actions or gateway status. "WHEN" allows the scene to check different conditions which conditions can be, e.g. always, every day, every week or during a certain period of time. When no time interval is assigned, the condition “always” will be applied automatically.

FAQ What should I do if I have forgotten my password? During operation, press the reset button on the back of the device for five seconds. The gateway then restores the standard admin access and standard network configuration (DHCP). How do I exclude a device from the component list if it is defective or lost? If your device can no longer establish a connection to the gateway, it can be removed from the gateway by pressing the following ICON: Note: If a device does not respond for more than 24 hours, the symbol appears Why my device cannot be included? 1. Make sure that your Z-Wave gateway and the device communicate on the same frequency. 2. Your device may already be connected to another Z-Wave network, so try an exclusion first. 3. The battery of the device is empty. What is the default admin login? Standard admin user: admin Standard admin password: _____ (empty) Scope of delivery Gateway ID / Password Card Quickguide Ethernet Cable Power Supply 5V / 1,5A (DC-Stecker: 3,5 x 1,35mm) Product description 1 Z-Wave LED-Indicator 2 Netzwerk LED-Indicator 3 Status LED-Indicator 4 Reset-Button 5 Power Supply (5V DC / 1A) 6 LAN-interface 7 Speaker Reset – Factory Default To completely reset your Z-Wave Gateway to factory settings, connect to the device using the ABUS Z- Wave One App. Open the configuration and select the option "Z-Wave Factory Settings" in the admin area. If this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable.

Z-Wave configuration Association group Group No. Max. Nodes Description 1 1 Z-Wave Plus Lifeline, report Device Reset Locally when reset Device Detection Added device will detect automatically, users can control it (on/off, change color, lighting, etc.) and watch information (battery, meter, etc.) via Z-Wave ONE App. Different brands Z-Wave enabled device can be included and excluded normally. Included devices will show on device list. All non-battery powered nodes can act as repeaters regardless of manufacturers. Basis command Basic command is useful in a scene. Replication Controller can transmit protocol replication data automatically. About Security This controller is a security enabled Z-Wave Plus product. If necessary, it will use encrypted Z-Wave Plus messages to communicate to other security enabled Z- Wave Plus products. BASIC SET For unknown device, press device icon will show on/off icon, select on/off and press ok will send BASIC SET 0xff/0x00. Z-Wave Command Classes Supported Z-Wave Command Classes: COMMAND_CLASS_ZWAVEPLUS_INFO _V2 COMMAND_CLASS_VERSION_V2 COMMAND_CLASS_ASSOCIATION_GRP_INFO COMMAND_CLASS_ASSOCIATION_V2 COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2 COMMAND_CLASS_SECURITY COMMAND_CLASS_SECURITY_2 COMMAND_CLASS_DEVICE_RESET_LOCALLY COMMAND_CLASS_APPLICATION_STATUS COMMAND_CLASS_POWERLEVEL COMMAND_CLASS_CONTROLLER_REPLICATION COMMAND_CLASS_BASIC COMMAND_CLASS_CRC_16_ENCAP COMMAND_CLASS_TRANSPORT_SERVICE_V2 COMMAND_CLASS_SUPERVISION Controlled Command Classes: COMMAND_CLASS_BASIC COMMAND_CLASS_SECURITY COMMAND_CLASS_SECURITY_2 COMMAND_CLASS_ASSOCIATION_GRP_INFO COMMAND_CLASS_ASSOCIATION_V2 COMMAND_CLASS_WAKE_UP_V2 COMMAND_CLASS_MULTI_CHANNEL_V4 COMMAND_CLASS_SWITCH_BINARY COMMAND_CLASS_SWITCH_MULTILEVEL_V2 COMMAND_CLASS_SENSOR_BINARY_V2 COMMAND_CLASS_SENSOR_MULTILEVEL COMMAND_CLASS_METER COMMAND_CLASS_COLOR_CONTROL COMMAND_CLASS_DOOR_LOCK COMMAND_CLASS_NOTIFICATION_V4 COMMAND_CLASS_BATTERY COMMAND_CLASS_SENSOR_ALARM COMMAND_CLASS_INCLUSION_CONTROLLER COMMAND_CLASS_CRC_16_ENCAP

Sie in der Bedienungsanleitung erhältlich auf der Website: abus.com/product/SHGW10000 Vous trouverez une alternative de mise en service ainsi que des informations détaillées dans le manuel d’utilisateur disponible sur le site Internet : abus.com/product/ SHGW10000 Een alternatieve ingebruikname en gedetailleerde informatie vindt u in de gebruikershandleiding op de website: abus.com/product/SHGW10000 Per informazioni su una messa in funzione alternativa o sui dettagli del prodotto, consultare le istruzioni per l‘uso disponibili all‘indirizzo: abus.com/products/SHGW10000 An alternative installation as well as detailed information can be found in the user manual which is available on the website: abus.com/product/SHGW10000 Alternativ idrifttagning samt detaljerede oplysninger findes i betjeningsvejledningen, som findes på hjemmesiden: abus.com/product/SHGW10000 Informacje dotyczące alternatywnych sposobów uruchomienia oraz dodatkowe szczegóły znajdują się w instrukcji obsługi, którą można pobrać na stronie: abus.com/ product/SHGW10000 En el manual de instrucciones disponible en nuestra página web podrá consultar una puesta en funcionamiento alternativa, así como información más detallada. abus.com/product/SHGW10000 Alternativ idrifttagning samt detaljerad information finns i bruksanvisningen som kan hämtas på webbsidan: abus.com/product/SHGW10000