Globel GL6000 Assembly Instructions Manual

5'w x 3'd 6'w x 3'd 6'w x 4'd 8'w x 3'd 8'w x 4'd © Globel Industries Pty Ltd GI00045 September 30 2015 E N G L I S H

GI00045 September 30 2015 Choking Hazard - This product contains small parts. It's Not That Difficult! IMPORTANT! Read These Instructions FIRST. The construction of your shed isn't as complicated as it may first appear. Our step by step, illustrated instructions are easy to follow, and we provide hints to make the assembly even easier. Simply follow our recommendations and carefully study our illustrations, then your garden shed will be assembled quickly and accurately. Make sure the site you choose for your garden shed is firm and level, and water drains away from the site. Do not install the garden shed in areas subject to high winds. Do not assemble the garden shed on a windy day. Your garden shed should be assembled on a specifically prepared base, ie concrete slab or pavers (or a suitable Garden Shed Foundation Kit) and then secured using the recommended dyna bolts as listed in the "Tools Required" page. A heavy duty polythene sheet should be placed under the foundation to assist in reducing rising dampness from the soil, thus reducing condensation build up in your garden shed. Once secured, we highly recommend applying silicone along the inside of the base rail to prevent water from seeping under the base frame and into your shed. Do not backfill against the shed's walls or base, as this will cause corrosion and void the warranty. Check the labelling on the Parts Cartons to ensure you have the shed model you ordered, and the correct number of Parts Cartons. For simplicity, in most part, this manual illustrates the construction of a 6' wide x 4' deep garden shed, with additional instructions for 5' and 8' wide garden sheds inserted where applicable. TOOLS INFORMATION: The tools you need are shown in the "TOOLS REQUIRED" section as all holes for screws and nuts and bolts are pre-drilled (excluding one hole only, which will require a 3mm drill bit) you will only need a power screw driver or a cordless drill with a magnetic Phillips-head tip to make the assembly quicker and easier. Do not over-tighten self-tapping screws. Nuts can be tightened by holding your finger on them as you tighten the bolt with the power screw driver - no spanner needed. CHECK THE PARTS: Before you start, separate and identify all the parts and hardware. (Refer to Parts List diagrams in the following pages). WARNING: Edges are sharp - Handle with care - Using gloves is highly recommended. WE RECOMMEND you get a second pair of hands to assist you with the assembly. INSTALLATION ADVICE Garden Shed Specifications SHED TYPE / SIZE BASE DIMENSIONS (Front x Sides mm) ROOF DIMENSIONS (Front x Sides mm) WALL SHEET HEIGHT mm Front Back OVERALL HEIGHT mm DOOR OPENING (Height x Width mm) No. CARTONS (Weight Kg) Size (Feet) Type Double Sliding Doors 5 x 3 1400 x 820 1480 x 930 1780 1935 1700 x 590 1 (40) 1785 Double Sliding Doors 6 x 3 1710 x 820 1800 x 930 1780 1935 1700 x 625 1 (43) 1785 Double Sliding Doors 6 x 4 1710 x 1130 1800 x 1240 1780 1975 1700 x 625 1(50) 1785 Double Sliding Doors 8 x 3 2340 x 820 2420 x 930 1780 1935 1700 x 1050 2 (55) 1785 Double Sliding Doors 8 x 4 2340 x 1130 2420 x 1240 1780 1975 1700 x 1050 2 (60) 1785 1 E N G L I S H

(P2) Battery Power Drill Dyna Bolts (not supplied) 6.5mm x 36mm recommended 2 Masonry Drill Bit 6.5mm Steel Drill Bit 3mm © Globel Industries Pty Ltd GI00045 September 30 2015 E N G L I S H

3 5' x 3' 6' x 3' 6' x 4' 8' x 3' 8' x 4' Roof Corner Cap Corner Brace Left Top-Wall Rail Bracket Right Top-Wall Rail Bracket Door Glide Door Glide Roller Door Spacer Door Handle Screws Nuts Bolts Washers HARDWARE KIT NOTE: Hardware Kit is packed in Carton '1' for all models 4 6 2 2 4 16 4 2 1 x bag 1 x bag 1 x bag YES 4 6 2 2 4 16 4 2 1 x bag 1 x bag 1 x bag YES 4 6 2 2 4 16 4 2 1 x bag 1 x bag 1 x bag YES 4 6 2 2 4 16 4 2 1 x bag 1 x bag 1 x bag YES 4 6 2 2 4 16 4 2 1 x bag 1 x bag 1 x bag YES Corner Panel Wall Sheet (Full) Wall Sheet (Half) Door Jamb Roof Sheet (Full) Roof Sheet (Half) Door Roof Starter (Left) Roof Starter (Right) Front Fascia Panel CARTON '1' QTY 4 3 1 2 2 - 2 1 1 1 QTY 4 4 - 2 2 1 2 1 1 1 QTY 4 4 2 2 2 1 2 1 1 1 QTY 4 5 2 2 3 1 2 1 1 1 x Left & 1 x Right 1 x Left & 1 x Right QTY 4 5 4 2 3 1 2 1 1 Above Door Fascia Door Brace (Top & Bottom) Gable (Left) Gable (Right) 1 2 of each 1 1 1 2 of each 1 1 1 2 of each 1 1 1 2 of each 1 1 1 2 of each 1 1 CARTON '2' - (8' wide wide models only) NOTE: Carton '2' parts as listed below for 5' wide and 6' wide models are packed in Carton '1'. Base Rail (Front) Base Rail (Back) Side Base Rail (Left) Side Base Rail (Right) Front Mid-Wall Brace (Left) Front Mid-Wall Brace (Right) Side Mid-Wall Brace Back Mid-Wall Brace Right Side Top-Wall Rail Left Side Top-Wall Rail Front Top Rail Back Top Rail Front Roof Trim Back Roof Trim Entry/Exit Ramp 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 © Globel Industries Pty Ltd E N G L I S H GI00045 September 30 2015

CHOKING HAZARD - This product contains small parts. WARNING LEFT FRONT & BACK TOP-WALL RAIL BRACKET RIGHT FRONT & BACK TOP-WALL RAIL BRACKET © Globel Industries Pty Ltd E N G L I S H GI00045 September 30 2015

CORNER PANEL FULL WALL SHEET HALF WALL SHEET DOOR JAMB (5' & 6' WIDE SHEDS ONLY) DOOR DOOR JAMB (8' WIDE SHEDS ONLY) LEFT ROOF STARTER RIGHT ROOF STARTER RIGHT GABLE LEFT GABLE HALF ROOF SHEET FULL ROOF SHEET 5 ABOVE DOOR FASCIA FRONT FASCIA PANEL (5' & 6' WIDE SHEDS ONLY) (8' WIDE SHEDS ONLY) LEFT FRONT FASCIA PANEL RIGHT FRONT FASCIA PANEL E N G L I S H © Globel Industries Pty Ltd GI00045 September 30 2015

RIGHT SIDE BASE RAIL LEFT FRONT MID-WALL BRACE RIGHT FRONT MID-WALL BRACE BACK TOP-WALL RAIL BACK MID-WALL BRACE BACK BASE RAIL SIDE MID-WALL BRACE PARTS LIST - Carton '2' BACK ROOF TRIM FRONT ROOF TRIM E N G L I S H © Globel Industries Pty Ltd GI00045 September 30 2015

If you need to construct a concrete slab, this page shows the method and dimensions we recommend. Make sure the slab area is square by ensuring diagonal corner dimensions are equal. (Diagram B) Formwork must be100mm thick and level. (Diagram C) First, lay builders plastic on the ground as a barrier to rising moisture. (Diagram D) Then place F52 reinforcing steel mesh on top of the builders plastic, ensuring the steel mesh is raised off the plastic to a depth of approximately half the thickness of the formwork. (Diagram E) Then pour the concrete and allow five days to cure. ROOF WIDTH SLAB WIDTH ROOF DEPTH SLAB DEPTH SLAB DIMENSIONS 100mm 100mm Diagram A Determine the size of the concrete slab by adding 100mm to the width and 100mm to the depth of the roof size of the shed. (See Diagram A). Adding the additional 100mm prevents rainwater from the roof creating a trench, and splashing soil against the walls of the shed, which could cause corrosion. A B C MEASUREMENT 'X' = MEASUREMENT 'Y' SLAB AREA X Y Y X Diagram B Diagram C FORMWORK SPIRIT LEVEL FORMWORK BUILDERS PLASTIC Diagram D F52 REINFORCING STEEL MESH MESH RAISED TO APPROXIMATELY HALF THICKNESS OF FORMWORK F52 REINFORCING STEEL MESH Diagram E 7 E N G L I S H © Globel Industries Pty Ltd GI00045 September 30 2015

OF TOP RAIL DOOR GLIDE SLOT SLOT FRONT FACE OF TOP RAIL TOP RAIL (FRONT) FLANGE FRONT FACE OF TOP RAIL SLOT Pre-Assembly FRONT TOP RAIL AND DOOR GLIDES Slip the four rollers onto the four spindles of each of the four door glides as shown in Diagram 1. (ii) Slide the four door glides with rollers attached, into the slot under the front top rail. Hint: Front top rail is the longest of the three aluminium rails. IMPORTANT: Make sure rollers don't slip off. 8 Note: The door glides MUST be positioned with the CURVED side facing the FRONT face of the top rail as shown. See Diagram 2. E N G L I S H © Globel Industries Pty Ltd GI00045 September 30 2015

9 FLANGE AT TOP SCREW RIGHT SIDE TOP-WALL RAIL SCREW RIGHT BACK TOP-WALL RAIL BRACKET FLANGE AT TOP (ii) Using one of the top-wall rails, slide the corresponding top-wall rail brackets into each end as shown in Diagram 3 below. Then secure each end with a screw as shown. Repeat using remaining top-wall rail and the two top-wall rail brackets. IMPORTANT: Both side top-wall rails have a sharper angle at one end as shown in Diagram 3A. Each of the top wall-rail brackets have a wide and narrow section and MUST be inserted as shown in Diagram 3. Diagram 3A TOP-WALL RAIL TOP-WALL RAIL SHARPER ANGLE END SHARPER ANGLE END NARROW SECTION NARROW SECTION END WITH SHARPER ANGLE END WITH SHARPER ANGLE WIDE SECTION WIDE SECTION E N G L I S H © Globel Industries Pty Ltd GI00045 September 30 2015

(iii) (i) (ii) Attach door braces as shown in Diagram 4, by sliding the underside of the brace under the door edge, so the underside of the front face of the door brace is seated onto the front face of the door panel. Secure using nuts and bolts ONLY IN HOLES AS SHOWN. IMPORTANT: Ensure elongated holes in braces match elongated holes in doors. Attach two door spacers to the bottom of each door as shown below. Attach one door handle to each door as shown. Pre-Assembly SLIDING DOORS BOTTOM OF DOORS TOP OF DOORS TOP OF DOOR DOOR BRACE DOOR BRACE DOOR DOOR Diagram 4 DOOR SPACER DOOR SPACER DOOR HANDLES NOTE: Doors for 6' wide sheds are shown here. Doors for 8' wide sheds have two extra holes per door along top and bottom edges. Doors for 5' wide sheds have only 5 holes along top edge and 5 holes along bottom edge. DOOR BRACE FIXED IN POSITION UNDERSIDE OF FRONT FACE OF DOOR BRACE SEATED ON FRONT FACE OF DOOR PANEL FRONT FACE OF DOOR PANEL FRONT FACE OF DOOR PANEL 10 E N G L I S H © Globel Industries Pty Ltd GI00045 September 30 2015

Step 2 Attach corner braces to each end of the back base rail, and secure to side base rails as shown in Diagram 1A. Note: Familiarise yourself with the profile of each base rail. IMPORTANT: The small holes on the vertical (side) faces of each base rail MUST face outwards. Refer to Diagram 1 HINT: Make sure the frame is square by measuring from corner to corner with a tape measure. RIGHT SIDE BASE RAIL FRONT BASE RAIL BACK BASE RAIL Diagram 1 4 2 1 IMPORTANT: Small holes on ALL base rails MUST face outwards. BACK FRONT LEFT SIDE BASE RAIL Diagram 1A CORNER BRACE BACK BACK BASE RAIL Garden Shed Construction 11 LEFT SIDE BASE RAIL 3 E N G L I S H © Globel Industries Pty Ltd GI00045 September 30 2015

LEFT SIDE BASE RAIL FRONT BASE RAIL Diagram 2 CORNER PANEL (AT RIGHT CORNER) BACK FRONT FRONT RIGHT CORNER 2 3 1 FIT SCREWS IN THIS ORDER Step 3 Step 4 Fit one corner panel to the base rail outer edge in the FRONT RIGHT CORNER as shown in Diagram 2. IMPORTANT: WIDER face of panel MUST FACE FRONT. Secure with three screws in numerical order as shown in Diagram 2. IMPORTANT: Bend all four panels to a 90 angle by following the instructions and diagrams to the right. Corner panels are supplied bent to a 135° angle. ° Lay the panel on a non-scratch surface and carefully form the angle to 90° by slowly working along the panel and bending it as you go. See Diagrams A - D. IMPORTANT: DO NOT OVER BEND PANEL. IMPORTANT: Throughout these instructions fit screws in the order shown (where applicable). Diagram B Diagram A Repeat the procedure for the second corner panel at the BACK RIGHT CORNER, ensuring WIDER face of the panel faces the BACK. See Diagram 3. Then fit one side mid-wall brace to the two corner panels at the centre hole position, and secure using a screw at each end of the mid-wall brace. See Diagram 3. IMPORTANT: Holes at each end on the thin face of the side mid-wall brace MUST face upward. Diagram 3 1 BACK FRONT SIDE MID-WALL BRACE HOLES ON THIN FACE MUST FACE UPWARD WIDER FACE MUST FACE BACK CORNER PANEL RIGHT SIDE BASE RAIL BACK BASE RAIL 2 3 5 2 3 1 FRONT BASE RAIL RIGHT SIDE BASE RAIL FRONT CORNER PANEL WITH WIDER FACE AT FRONT 2 3 1 12 FORMING CORNER PANELS FITTING CORNER PANELS 135° 90° Diagram C Diagram D CORNER PANEL END PROFILE AS SUPPLIED FOLDED TO REQUIRED ANGLE 4 E N G L I S H © Globel Industries Pty Ltd GI00045 September 30 2015

two corner panels and mid-wall brace at the LEFT side. See Diagram 4. IMPORTANT: Ensure the wider faces of the corner panels are facing front and back. This step uses pre-assembled components. Step 6 Attach and secure both side top-wall (left and right) rail assemblies to the inside of the corner panels as shown, using one screw at each end of rail. See Diagram 5. IMPORTANT: The ends of the side top-wall rail assemblies with the WIDE section brackets MUST be positioned at the FRONT of the shed, and the NARROW section brackets positioned at the back of the shed. IMPORTANT: The two faces of the side top rails, with multiple holes, MUST face outwards and top of shed. IMPORTANT: The two faces of the back top rail, with multiple holes, MUST face back and top of shed. BACK FRONT MID-WALL BRACE Diagram 4 1 2 3 8 CORNER PANELS AT LEFT SIDE, WITH WIDER FACES AT FRONT & BACK 5 4 7 6 Step 7 Attach the BACK top rail as shown in Diagram 6. HINT: Push the corner panels out slightly, to allow each end of the brackets to be inserted. Secure using one screw at each end of the top rail, and secure top of both corner panels to back rail using two screws per panel, as shown in Diagram 6. Diagram 6 BACK TOP RAIL WITH HOLES FACING BACK AND TOP TOP-WALL RAIL BRACKET BACK 13 LEFT TOP-WALL RAIL BRACKET PUSH SIDE WALL SHEET OUT BACK TOP RAIL CORNER PANEL FLANGE MUST FACE UPWARD FRONT BACK CORNER PANEL (LEFT SIDE) Diagram 5 RIGHT SIDE TOP-WALL RAIL ASSEMBLY BRACKET WITH NARROW SECTION AT BACK LEFT SIDE TOP-WALL RAIL ASSEMBLY CORNER PANEL (RIGHT SIDE) LEFT SIDE TOP-WALL RAIL E N G L I S H © Globel Industries Pty Ltd GI00045 September 30 2015

THE ONE INSERTED, to the top-wall rail brackets at front, as shown in Diagram 7. WITH DOOR GLIDES This step uses a pre-assembled component. FRONT TOP RAIL WITH DOOR GLIDES Diagram 7 DOOR GLIDES FACING FRONT FRONT BACK Step 9 Attach the back mid-wall brace to the inside of the BACK corner panels, at the centre hole position, using two screws at each end. See Diagram 8. IMPORTANT: Holes at each end on the thin face of the back mid-wall brace MUST face upward. Step 9A Secure the back and LEFT side mid-wall braces together using a corner brace and four screws as shown in Diagram 8A. Repeat for right side. LEFT SIDE MID-WALL BRACE INSIDE VIEW OF LEFT BACK CORNER PANEL BACK MID-WALL BRACE CORNER BRACE BACK Diagram 8A Diagram 8 BACK MID-WALL BRACE HOLES AT EACH END ON THE THIN FACE MUST FACE UPWARD FRONT BACK E N G L I S H © Globel Industries Pty Ltd GI00045 September 30 2015

sliding the bottom back edge of the fascia panel into the flange at the top of the front top rail. See Diagram 9. IMPORTANT: If you are constructing an 8' wide shed go directly to Step 10A now. ATTACHING THE FRONT FASCIA PANEL 5' & 6' wide sheds FLANGE ON FRONT TOP RAIL BOTTOM BACK EDGE FRONT FASCIA PANEL FRONT TOP RAIL SCREW BACK FRONT FASCIA PANEL (INSIDE VIEW) TOP RAIL Diagram 10 FRONT FASCIA PANEL (RIGHT SIDE VIEW) FLANGE ON FRONT TOP RAIL BOTTOM BACK EDGE FRONT FASCIA PANEL FRONT TOP RAIL FRONT FASCIA PANEL (RIGHT SIDE VIEW) Diagram 11 Step 11 Fit the left and right side gables to the side top-wall rails by sliding the inside bottom edge of the gable into the flange at the top of the side top-wall rail and secure using screws. See Diagram 12. ATTACHING THE 2 SIDE GABLES FRONT FRONT FASCIA PANEL FLANGE AT TOP OF FRONT TOP RAIL Diagram 9 Fit the left and right front fascia panels to the FRONT top rail by sliding the bottom back edge of one panel into the flange at the top of the front top rail and aligning it to the left side of the top rail. See Diagram 11. Then repeat for the other panel, overlapping the holes at the centre. See Diagram 11. 8' wide shed IMPORTANT: Ensure LEFT front fascia panel is positioned at LEFT side (when viewing from front of shed) and RIGHT front fascia panel is positioned at RIGHT side. The left and right panels can be identified by having no hole at the outside edge of the bottom flange. See Diagram 11. Secure using eight screws into the top beam and four nuts and bolts in the centre overlapping holes of the front fascia panels. See Diagram 11. SCREW BACK TOP RAIL BOTTOM FLANGE FRONT FASCIA PANELS (INSIDE VIEW) NUT & BOLT RIGHT FRONT FASCIA PANEL WITH NO HOLE NEAR EDGE OF BOTTOM FLANGE LEFT FRONT FASCIA PANEL WITH NO HOLE NEAR EDGE OF BOTTOM FLANGE OVERLAPPING HOLES Diagram 12 LEFT SIDE GABLE FRONT FASCIA PANEL NUT & BOLT NUT & BOLT RIGHT SIDE TOP-WALL RAIL RIGHT SIDE GABLE FRONT FLANGE RIGHT SIDE TOP-WALL RAIL INSIDE BOTTOM EDGE RIGHT SIDE GABLE (FRONT EDGE) GABLE - RIGHT SIDE (FRONT VIEW) SCREW SCREW 15 Secure to the front fascia panel using four nuts and bolts as shown. NOTE FOR 3' DEEP SHEDS ONLY: Only three nuts and bolts are required to join the gables to the front fascia panel in the corresponding far right and left corners. See Diagram 12. Secure using six screws. See Diagram 10. E N G L I S H © Globel Industries Pty Ltd GI00045 September 30 2015

Starting at the BACK RIGHT SIDE of the shed: Refer to Diagrams 13 (4' deep shed) and 13A (3' deep shed). Fit one half wall sheet (or one full wall sheet, depending on the depth of your shed) overlapping the first ridge of the RIGHT BACK corner panel and secure to the bottom, top and middle rails/brace, using screws, and following the numerical order shown in both diagrams. IMPORTANT: READ BEFORE ATTACHING WALL SHEETS FOLLOW STEP 12A and DIAGRAM 15 (SEE NEXT PAGE) for fitting the last wall sheet at the right side to the RIGHT FRONT CORNER PANEL. 16 EXAMPLES OF WALL SHEET CONFIGURATIONS FOR 3 SHED SIZES - BACK & FRONT (width) & SIDES (depth) 6' WIDE x 4' DEEP SHED: BACK FULL FULL SIDES FULL 1 / 2 5' WIDE x 3' DEEP SHED: BACK SIDES FULL FULL 1 / 2 8' WIDE x 4' DEEP SHED: FRONT DOORS BETWEEN 1 / 2 1 / 2 BACK FULL FULL FULL SIDES FULL 1 / 2 Diagram 14 3' Deep Shed Diagram 13A FIRST RIDGE OF RIGHT BACK CORNER PANEL FRONT BACK 8 5 11 10 12 9 4 3 2 1 7 6 FULL WALL SHEET 4' Deep Shed FIRST RIDGE OF RIGHT BACK CORNER PANEL HALF WALL SHEET HALF WALL SHEET FIT THIS FIRST FULL WALL SHEET FIT THIS SECOND FRONT BACK Diagram 13 14 11 17 16 18 15 10 9 8 7 13 12 4 3 2 1 5 6 IMPORTANT: Fit screws in this order for all wall sheets: Bottom row, Top row, Middle row, working left to right. E N G L I S H © Globel Industries Pty Ltd GI00045 September 30 2015

the side edge of the corner panels. Then, by slightly prising the back edge of the corner panels away from the frame with your hand, slide the front edge of the wall sheets in behind. See diagram 15. Re-tighten the three screws in the corner panels and secure the wall sheets, using screws, in the numerical order shown in Diagram 13. NOTE: For aesthetics we recommend the full wall sheets underlap the sides of the front corner panels. This 'underlapping' creates the appearance of the shed wall being one continuous sheet. FITTING SIDE WALL SHEETS TO FRONT RIGHT & LEFT CORNER PANELS. Step 12A 17 LEFT FRONT CORNER PANEL LEFT SIDE WALL SHEETS ALL SCREWS FITTED IN SEQUENCE SHOWN IN DIAGRAM 13 Diagram 15 BACK RIGHT FRONT CORNER PRISE UP CORNER PANEL AWAY FROM FRAME FRONT EDGE OF FULL WALL SHEET RIGHT FRONT CORNER PANEL LOOSEN OFF SIDE SCREWS FRONT FRONT EDGE OF FULL WALL SHEET SLIDES IN BEHIND CORNER PANEL RIGHT FRONT CORNER PANEL RIGHT FRONT CORNER LEFT BACK CORNER PANEL E N G L I S H © Globel Industries Pty Ltd GI00045 September 30 2015

starting at the RIGHT BACK corner panel and overlapping each sheet. Secure them with screws to the back bottom, top and middle rails/brace, in the same sequence as shown in Diagram 13. See Diagram 16. Step 12B WALL SHEETS - BACK Step 14 Secure the right front and side mid-wall braces together using a corner brace and four screws as shown in Diagram 18. Repeat for left side. FRONT MID-WALL BRACE CORNER BRACE SIDE MID-WALL BRACE INSIDE VIEW OF RIGHT FRONT CORNER PANEL FRONT Diagram 18 Attach the left and right front mid-wall braces to the inside corner panels, securing with two screws in each side as shown in Diagram 17. HINT: The left and right front mid-wall braces can be distinguished by the position of the holes on the vertical and top faces. See Diagram 17. Step 13 18 LEFT FRONT MID-WALL BRACE FRONT HOLES ON VERTICAL FACE HOLES ON TOP FACE RIGHT FRONT MID-WALL BRACE Diagram 17 FRONT FULL WALL SHEETS BACK RIGHT BACK CORNER PANEL ALL SCREWS FITTED IN SEQUENCE SHOWN IN DIAGRAM 13 Diagram 16 E N G L I S H © Globel Industries Pty Ltd GI00045 September 30 2015

and secure using six screws. See Diagram 20. 19 WALL SHEETS - FRONT IMPORTANT: 8' wide shed, go directly to Step 15A now. If you are NOT assembling an Fit the front left and right wall sheets to the corner panels by slightly prising up the edges of the corner panels and sliding the wall sheets under, as shown in Step 12A, Diagram 15, Page 17. Secure using screws and follow the numerical order shown in Diagram 13, page 16. See Diagram 19. DOOR JAMBS Attach one of the door jambs to the front corner panels the front sheet (for 8' wide sheds) by slightly prising up the edges of the corner panels or front wall sheets and sliding the door jambs under, as shown in Step 12A, Diagram 15, Page 17. NOTE: Door jambs for 8' wide sheds are different in shape to those shown in Diagram 19A. (for 6' wide sheds) or Step 15A FOR 6' WIDE SHED: Secure with three screws in the bottom of the door jamb, two screws (ONLY) in the top of the door jamb and three screws in the front mid-rail. See Diagram 19A. FOR 8' WIDE SHEDS: Secure with two screws in the bottom of the door jamb, one screw (ONLY) in the top of the door jamb and two screws in the front mid-rail. IMPORTANT - ALL Shed Sizes: Leave top inside hole empty, as shown in Diagram 19A NOTE: FRONT WALL SHEETS are ONLY relevant to 8' wide sheds and MUST be attached prior to the door jambs. Refer to Page 16, Diagram 14 to see which size wall sheet applies to the shed size you are assembling. FITTING DOOR JAMBS (AND FRONT WALL SHEETS WHERE APPLICABLE) LEFT FRONT WALL SHEET RIGHT FRONT WALL SHEET NOTE: Half wall sheet shown FRONT Diagram 19 ALL SCREWS FITTED IN SEQUENCE SHOWN IN DIAGRAM 13 LEFT CORNER PANEL 8' Wide Shed Shown FRONT LEFT DOOR JAMB Diagram 19A LEAVE THESE HOLES EMPTY LEFT CORNER PANEL RIGHT DOOR JAMB 6' Wide Shed Shown E N G L I S H © Globel Industries Pty Ltd GI00045 September 30 2015

every screw and bolt must have a washer. NOTE: Nuts and bolts fitted upside down along the front top edge of roof starters and roof sheets to front fascia must have the washers placed under the nut. SCREW BOLT WASHER WASHER Fit the RIGHT roof starter to the top edge of the RIGHT side gable and secure to the top of the front fascia using two nuts and bolts in the positions shown in Diagram 21. IMPORTANT: Insert bolts from the bottom. Place washers under nuts. Step 17 ROOF STARTERS & SHEETING ROOF STARTERS IMPORTANT: NUTS AND BOLTS MUST BE INSERTED AS SHOWN Repeat procedure for left side roof starter. See Diagram 23. Step 17A Secure the RIGHT roof starter to the side gable assembly using six nuts and bolts with washers, in the holes along the vertical edge of the roof starter. See Diagram 22. Then fit a screw in the hole near the bottom of the roof starter and into the top edge of the back top rail as shown in Diagram 22. Diagram 21 TOP EDGE OF SIDE GABLE RIGHT ROOF STARTER FRONT BACK NUT & BOLT THROUGH FRONT FASCIA WASHER MUST BE PLACED UNDER NUT FRONT BOTH ROOF STARTERS IN PLACE Diagram 23 Diagram 22 HOLE IN VERTICAL EDGE OF ROOF STARTER 6 NUTS & BOLTS IN EDGE OF ROOF STARTER NOTE: 3' DEEP SHEDS ONLY REQUIRE 4 NUTS & BOLTS FRONT BACK RIGHT ROOF STARTER SCREW INTO BACK TOP RAIL FRONT FASCIA E N G L I S H © Globel Industries Pty Ltd GI00045 September 30 2015

fit roof sheets in the sequence shown in the “Roof Sheet Installation Number Sequences” Diagram at the bottom of this page, ensuring they are the correct way up, and the side edges overlap the corresponding roof starters. First, secure the front edge to the top of the front fascia panel using nuts and bolts as shown in Diagram 24. NOTE: insert the nuts and bolts from the bottom and place the washers under the nuts. Then secure the back and side edge using screws, nuts and bolts as shown in Diagram 24. NOTE FOR 3' DEEP SHEDS ONLY: Nut & bolt into side edge is NOT required. Continue fitting sheets using screws, nuts and bolts, depending on the roof sheets used (full or half). See Diagram 25. 21 ROOF SHEET INSTALLATION NUMBER SEQUENCES: FULL FULL 1 2 FULL FULL FULL 1 HALF 2 3 4 FULL FULL 1 HALF 2 3 5' WIDE 2 x full roof sheets 8' WIDE 6' WIDE 3 x full roof sheets, 1 x half roof sheet 2 x full roof sheets, 1 x half roof sheet FRONT BACK RIGHT SIDE 4 SCREWS ALONG BACK EDGE 1 NUT & BOLT IN CENTRE HOLE OF SIDE EDGE NOTE: NOT REQUIRED FOR 3' DEEP SHEDS IMPORTANT: EDGE WITH THE MOST HOLES IS AT BACK 4 NUTS & BOLTS ALONG FRONT EDGE NOTE: INSERT BOLTS FROM THE BOTTOM. FULL ROOF SHEET EDGE OF FULL ROOF SHEET TO OVERLAP EDGE OF ROOF STARTER Diagram 24 WASHER MUST BE PLACED UNDER NUT. NOTE: NUT & BOLT IN CENTRE HOLE OF SIDE EDGE NOT REQUIRED FOR 3' DEEP SHEDS FRONT Diagram 25 BACK FULL ROOF SHEET EDGE OVERLAPS FIRST SHEET EDGE OVERLAPS ROOF STARTER E N G L I S H © Globel Industries Pty Ltd GI00045 September 30 2015

WIDE SHEDS FRONT ROOF TRIM NUTS AND BOLTS IN THE 4 INNER HOLES ONLY 4 ROOF CORNER CAPS IN PLACE TOP FACE OF ROOF SHEET UNDERSIDE OF TOP EDGE OF ROOF TRIM SEATED ON TOP FACE OF ROOF SHEETS Fit the four roof corner caps to the left and right ends of both roof trims and secure with nuts and bolts as shown in Diagram 27. Step 20 Step 19 Attach the roof trims to the front and back edges of the roof sheets as shown in Diagram 26, by sliding the bottom edge of the roof trims under the edge of the roof sheets so the underside of the top edge of the roof trims are seated on the top face of the roof sheets. Secure using one screw, and nuts and bolts ONLY IN HOLES AS SHOWN. IMPORTANT: FRONT ROOF TRIM - ALL SIZES: Using a 3mm steel drill bit, drill a pilot hole at the centre hole of the FRONT roof trim and into the roof sheet. Then fit a screw. NOTE: Roof corner cap fits OVER roof trim. Washers are not required for this step. 22 ROOF TRIM FIXED IN POSITION Diagram 27 ROOF CORNER CAP FITTING FRONT AND BACK ROOF TRIMS 2 1 DRILL A 3mm PILOT HOLE THEN FIT SCREW IMPORTANT: Back roof trims for 6' and 8' wide sheds require four nuts and bolts, back roof trim for 5' wide sheds require three nuts and bolts. See Diagram 26 and 26A. BACK ROOF TRIM FOR 5' WIDE SHEDS NUTS AND BOLTS IN THE 3 INNER HOLES ONLY E N G L I S H © Globel Industries Pty Ltd GI00045 September 30 2015

for the next door glide along, and secure it to two holes in the top right of the door. Gently push the left protruding edge of the door in behind the left door jamb, as shown in Diagram 30. Repeat the procedure (i to iii) for the right side door. (i) (ii) (iii) (iv) Diagram 30 LEFT DOOR JAMB GENTLY PUSH DOOR IN BEHIND DOOR JAMB Start by fitting LEFT side door: IMPORTANT: Work from the outside of the shed with the front face of the door facing you and the door handle at the right side. Taking the left door panel, tilt the top edge into the shed and under the door glides, as shown in Diagram 28. Then slot the bottom of the door into the groove in the entry/exit ramp as shown in Diagram 28A. FITTING SLIDING DOORS DOOR GLIDE TOP EDGE OF DOOR TILTED INTO SHED LEFT DOOR JAMB Diagram 28 This step uses pre-assembled components. Step 21 SLOT DOOR INTO GROOVE IN ENTRY/ EXIT RAMP DOOR DOOR GROOVE IN ENTRY/ EXIT RAMP Diagram 28A Diagram 29 FAR LEFT DOOR GLIDE NEXT DOOR GLIDE ALONG NUTS AND BOLTS IN CENTRE HOLES LEFT EDGE OF LEFT SIDE DOOR RIGHT EDGE OF LEFT SIDE DOOR LEFT DOOR JAMB Attach the top of the door to the FAR LEFT door glide by securing with one nut and bolt in each of the CENTRE holes of the door glide and through the holes at the top LEFT of the door, as shown in Diagram 29. 23 E N G L I S H © Globel Industries Pty Ltd GI00045 September 30 2015

parallel at the centre. If not, adjust the position of one of the bolts in the relevant door glide to either raise or lower the edge of the door to make it parallel with the edge of the other door. RECOMMENDATION In most cases, only a small adjustment is required by lifting or lowering the door slightly, which can be achieved without moving the bolt to another hole, but by simply loosening the bolts in the door glide and adjusting to suit, then re-tightening. Step 24 Fit the door fascia panel to the front top rail, using four screws as shown in Diagram 32. Diagram 32 DOOR FASCIA PANEL DOORS HINT: Extra holes are provided to align door if required. See Diagram 31. BOTH DOORS SHOULD BE PARALLEL WHEN CLOSED Diagram 31 DOOR GLIDE TOP HOLES BOTTOM HOLES 24 E N G L I S H © Globel Industries Pty Ltd GI00045 September 30 2015

REPLACEMENT OF DOOR GLIDES: SECURING & SEALING SHED BASE RAILS: Spraying a silicone spray into the slot under the front top rail and along the inside face of the internal front mid-wall brace, will assist in a smoother and quieter operation of sliding doors. Remove nuts and bolts from door glide(s) to be removed, and slide in direction away from handle side of door. Door glide will drop out from far end of slot under front top rail. Replace door glide by inserting into slot under front top rail, slide into position and secure with nuts and bolts. See diagram shown. Refer to Pre-Assembly Section "Door Glides" (page 8) and Steps 21 - 23 for full details on fitting door glides and adjustment of doors. We recommend the following procedure for securing and sealing shed base rails to concrete floor: SECURE - Secure shed base rails to concrete floor using dyna-bolts as shown in diagram. SEAL - and apply silicone on inside of shed, along the edge of the base rail and to the floor. Ensure floor is free of dust and debris Dyna Bolt 6.5mm x 36mm SILICONE 25 DOOR GLIDE. NOTE: CURVED SIDE FACING FRONT FACE OF GABLE ASSEMBLY SLOT SLIDE BOLT & NUT TOP RAIL E N G L I S H © Globel Industries Pty Ltd GI00045 September 30 2015

You must have a copy of your original purchase receipt if warranty is required. Globel Garden Sheds are built for the purpose of domestic use only and must be installed according to the steps and procedures in the assembly instructions booklet herewith. Installation of shed in ocean locations, heavy industrial or unusually corrosive environments voids the warranty. Warranty does not apply if proven that a third party contaminate contributed to the fault. Warranty is not transferable. Fasteners, door glides and other plastic parts are not covered by the warranty. Missing components must be claimed within 14 days of purchase. For any warranty claim you must contact the original place of purchase. Any expenses incurred by the claimant in conducting their claim will be at the expense of the claimant. Any expenses and/or labour incurred costs by the claimant for the purpose of the replacement and/or fixing any parts to the shed will be at the claimants expense. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Purchase details: Date of Purchase Model / Product Code Place of Purchase FOR YOUR RECORDS PLEASE STAPLE ORIGINAL PURCHASE RECEIPT HERE Receipt Number 26 E N G L I S H © Globel Industries Pty Ltd GI00045 September 30 2015