LawnMaster CLGT2425 Original Operation Manual

Before initial start-up, please read through these operating instructions carefully prior to using the machine. Keep the instructions safe and pass them on to any subsequent user so that the information is always available. Cordless Grass Trimmer Original operation manual

Symbols and icons ..........................5 General safety instructions ..............6 Use ........................................................9 General description .............................9 Survey .............................................9 Functional description .....................9 Extent of the delivery .......................10 Charging the battery ...........................10 Removing / inserting the battery .....10 Recharging the battery ....................10 Assembling instructions .....................11 Operation ............................................11 Turning on and off ...........................11 Checking the battery charge level ...11 Trimmer settings ...............................12 Manner of operation ............................12 Cutting grass ...................................12 Vertical cut / lawn edge trimming ....13 Cleaning and maintenance .................13 Cleaning ..........................................13 General maintenance ......................13 Replacing the cutting insert .............13 Storage .................................................13 Disposal and protection of the environ- ment ......................................................14 Guarantee .............................................14 Replacement parts ..............................14 Technical data ......................................15 Trouble shooting .................................16 Exploded Drawing ..............................17 CE declaration of conformity .............18 Safety instructions Ensure that the safety instructions are ob- served when operating the trimmer. Symbols and icons Symbols in the manual Warning symbols with informa- tion on damage and injury pre- vention. Instruction symbols (the instruc- tion is explained at the place of the exclamation mark) with information on preventing damage. Help symbols with information on improving tool handling. Symbols on the trimmer WARNING! Carefully read these Operating In- structions. Wear goggles and ear defenders. After turning off the appli- ance, the cutting disk will keep revolving for a couple of seconds. Keep away from your hand and feet. Do not expose the trimmer to moisture. Do not work when it is raining and do not cut wet grass. Keep by-standers well away. They could be in- please read this instruction manual carefully, for your own safety and for the safety of others. Keep the manual in a safe place and pass it on to any subsequent owner to en- sure that the information contained therein is available at all times.

Ensure that you are completely familiar with all the operating parts before you start working with the trimmer. Ask an experienced user or expert to explain all its functions, manner of operation and working techniques, and practise operating the trimmer. Ensure that you can instantly turn off the trimmer in the event of an emergency. Incorrect use of the trimmer can result in very serious injuries. Caution! When operating electri- cal appliances, the following basic safety precautions must be taken to protect yourself against the risks Working with the appliance: • This appliance is not intended for opera- tion by persons (including children) with reduced physical, sensory or mental capabilities, or lacking experience and/ or knowledge; unless they are under the supervision of or have been instructed on how to use the appliance by a person responsible for their safety. • Children should be supervised to pre- vent them from playing with the appli- ance. • The appliance must not be used by children and persons who have but incomplete knowledge of the operating instructions. Acts and local regulations may demand a minimum age for opera- tion. • Keep the appliance away from humans - mainly from children - and pets. Sus- pend your work when humans or pets are nearby. Always keep a safety clear- ance of 15 m in all directions. The ap- Remove the battery prior to serv- icing the appliance. Noise level rating LWA in dB Electrical appliances must not be disposed of with the domestic waste. Cutting circle Symbols on the battery Do not dispose of batteries in house- water. max. 60°C Do not subject the battery to strong sunlight over long periods and do not leave it on a heater (max. 60°C). Take batteries to an old battery collection point where they will be recycled in an environmentally friendly manner. Symbols on the recharger WARNING! - fully read through the user manual The recharger is for indoor use only. Protection class II Electrical appliances must not be disposed of with the domestic waste. Li-ion 6

• Wear suitable working clothes and personal protection equipment! Always wear goggles or other eye protection, ear protection, boots or shoes with non- slip soles and sturdy long trousers as well as gloves. This will reduce the risk of injury. Do not wear long clothing or jewellery because these might be caught by mov- ing parts. Do not operate the appliance bare-footed or when wearing open san- dals. • Be particularly careful when working down a slope. This will help you better control the appliance in unanticipated situations. • Do not operate the appliance when you are tired or after drinking alcohol or tak- ing tablets. Have regular breaks. Make sure the light is good during op- eration. • Do not work in the rain, bad weather or in wet environments. Water penetrating the appliance will increase the risk of electric shock. • The safety device and your personal protection equipment protect yourself and the health of others and will ensure that the appliance is working properly: Do not operate a damaged or incom- plete appliance or an appliance that has been manipulated without the manu- facturer’s permission. Never operate the appliance if the safety devices are defective. Prior to operation, check that the appliance is in a safe state taking the switch and the protective cover. • When turning on the appliance and when the motor is running, keep the trimming assembly away from all parts of your body and mainly from your hands and feet. Risk of injury! • Do not start the appliance when it is upside down or not in working position. Risk of injury! • Turn off the appliance and remove the battery when: - leaving the appliance unattended, - cleaning or servicing the appliance, - replacing the trimming assembly. This precaution will prevent the appli- ance from starting unintentionally. • When starting or working with the ap- pliance, make sure that the cutting disk does not contact stones, gravel, wire or other foreign bodies. • After turning off the appliance, the trim- ming assembly will keep revolving for a couple of seconds: Never try to stop the trimming assembly by hand. Always wait until it has stopped on its own. Risk of injury! • Only use OEM cutting inserts. You are not allowed to use a metal insert instead of the plastic insert. Metal inserts may cause accidents. • Do not use the appliance to cut grass not growing on the ground such as grass growing on walls, rocks, etc. • Do not cross gravel walks or streets with the appliance still running. Risk of injury • Do not operate the appliance near in- - • In the area of operation, the operator is liable for damages caused others as a result of operating the appliance. • Check that the ventilation slots are not clogged up. • Keep the appliance in a dry place and out of the reach of children. • Only use spares and accessories deliv- ered and recommended by the manu-

of the appliance in the long term. • Do not try to repair the appliance your- self. Work not described in this instruc- tion manual must only be done by cus- tomer service centres authorised by us. Diligent handling and operation of bat- tery-operated tools: • To recharge the batteries, only use chargers recommended by the manu- facturer. Battery chargers designed for a used with other types of batteries. • Only operate the electric tools on the - • If not in use, keep the battery away from paper clips, coins, keys, nails, screws and other small metal objects that may jumper the contacts. A short circuit be- tween the battery contacts may cause • Inappropriate use of the battery may cause liquid to escape from it. Avoid any contact with this liquid. If you do get into contact with it wash the affected part with water. Also consult a doctor if the liquid gets into your eyes. Battery liquid may irritate your skin or cause burns. • Before inserting the battery, check that the appliance is turned off. Inserting a battery in a turned-on electric tool may cause accidents. • Recharge the batteries indoors only because the battery charger is designed for indoor use only. • To reduce the electric shock hazard, un- plug the battery charger from the mains before cleaning the charger. • Do not expose the battery to strong sunlight for longer periods of time and do not deposit it on radiators. Heat will damage the battery and cause a risk of explosion. • Allow the battery to cool down before you recharge it. • Do not open the battery and avoid me- chanical damage to the battery. There is a risk of short circuit and the escape of vapours that will irritate the respiratory system. Let in fresh air and consult a doctor if you are feeling physical symp- toms. • Do not use non-rechargeable batteries! Correct handling of the battery charger • To charge the battery, use only the - sion. • Before each use, check the charger, cable and plug and have them repaired original parts. Do not use a defective charger and do not open it up yourself. This ensures that the safety of the de- vice is maintained. • Ensure that the mains voltage matches plate. Risk of electric shock. • Disconnect the charger from the mains before closing or opening connection to the battery / power tool / device. • Keep the charger clean and away from wet and rain. Do not use the charger outdoors. Dirt and the entry of water in- crease the risk of electric shock. • Operate the charger only with the appro- priate original batteries. Charging other batteries may result in injuries and risk • Avoid mechanical damage to the charger. This can result in internal short circuits. • Do not operate the charger on a com- bustible surface (e.g. paper, textiles. - ing.

is damaged, it must be replaced by the manufacturer, a customer service agent - son in order to prevent hazards. • The battery of the appliance is not fully charged at the time of delivery. It there- fore needs to be fully recharged before recharge cycle we recommend that you charge the battery for about 3-5 hour. Slot the battery into the base and plug the battery charger into a mains outlet. • When the battery is fully charged, un- plug the charger from the mains and from the appliance. Charging time is ap- prox. 3-5 hour. • Do not charge the battery continuously since this may damage the battery cells. Note: Repeatedly charging small capaci- ties may damage the battery cells. Re- charge the battery only if the appliance is becoming slow. Use The appliance is solely intended for cut- ting grass and weeds in the garden and for edge trimming. Any other use that is - tions can result in damage to the trimmer and give rise to serious danger for the user. Do not use the appliance to trim hedges or bushes. The appliance must only be used by adults. Young people aged 16 and over may only use the trim- mer under adult supervision. The user or operator is responsible for ac- cidents causing injury to other people or damage to property. The manufacturer cannot be held liable for damage when the trimmer is not used in conformity with its intended purpose or due to incorrect operation. General description The illustrations are on the front fold-out page. Survey 1 Top handle 2 On/Off switch 3 Switch lock 4 Box for cutting inserts (not vis- ible) 5 Auxiliary handle 6 Handle rod 7 Lock of handle rod adjustment 8 Threaded bush for length adjust- ment 9 Telescopic shaft 10 Motor head 11 12 Cutting disk 13 Cutting insert 14 Protective cover 15 Pedal for tilt angle adjustment 16 Battery 17 Battery release button 19 Battery charger operation indicator 18 Battery charger Functional description The trimming assembly of the manually controlled, portable, battery-operated lawn trimmer consists of a system of plastic knife/cutting insert. The appliance also features a pivoting mo- tor head, adjustable aluminium telescopic shaft, and a spacer bow. A hood covering the cutting device pro- tects the user. The following describes the functions of the operating parts.

Carefully unpack the trimmer and check that it is complete: • Battery-operated lawn trimmer • Protective cover • Auxiliary handle • 20 Cutting inserts • Battery charger • Battery Charging the battery Do not expose the battery to extreme conditions such as heat or impact. Risk of injury from escaping electrolytic solution! Prior to charging the battery, check that its outer surface is clean and dry. • The battery of the appliance is not fully charged at the time of delivery. It therefore needs to be fully recharged • Recharge the battery when you notice that the appliance is becoming slower. • Do not keep charging the battery continuously and avoid it becoming entirely discharged since this may damage the battery cells. The warranty excludes all defects caused by improper handling. • If a fully recharged battery lasts for considerably shorter operating times, the battery is used up and needs to be replaced. Only use an OEM battery pack replacement available from our Customer Service. • Always take heed of the applicable safety instructions as well as the envi- ronmental protection regulations and information. Removing / inserting the battery 1. To remove the battery (16) from the appliance, press the release button (17) on the battery and pull out the battery. 2. To insert the battery (16), place it on the guide track (21) and push it back into the appliance. It will audibly snap in. Do not insert the battery until the appliance is fully assembled. Risk of injury! Recharging the battery 1. Remove the battery (16) from the appliance, as necessary. 2. Inser the battery (16) in the charging compartment of the battery charger (18). It will audi- bly snap in. 3. Plug the battery charger (18) into a mains outlet. The charging indicator lamp (19) lights up: Permanent red light: charging Permanent green light: charging complete. Recommended charging time is approx. 3-5 hour. 4. When the battery is fully re- charged unplug the battery charger (18) from the mains. 5. Press the release button ( 17) on the battery (16) and pull the battery out of the battery charger (18).

the appliance is fully assembled. Risk of injury! To put on the protective cover: 1. Place the protective cover (14) on the motor head (10) and screw it down with the 3 Phillips screws. To put on the auxiliary handle: 1. Pull the ends of the auxiliary handle (5) to extend the han- dle and slide it over the handle holder (21). 2. Screw down the screw (22) in the auxiliary handle (5). To install the cutting insert: 1. Place the cutting insert (13) on the pin (23) on the cutting disk (12) and pull out the insert until it snaps in. Spare cutting inserts are kept in the box (4) on the auxiliary handle (5). To insert the battery: 1. To insert the battery (16), place it on the guide track (20) and push it into the appliance. It will audi- bly snap in. Operation Caution: risk of injury! Do not operate the appliance without the protective cover. To oper- ate the appliance, wear suitable clothing, eye and ear protection. Prior to every use, check that the appliance is operative. Do not block the On/Off switch or the switch lock. They must reli- ably turn off the motor when you release the switch. Do not oper- ate the appliance if one of the switches is damaged. Please observe local regulations concerning noise protection. Turning on and off appliance well with both hands and at some distance away from your body. Before turning on the appli- ance, check that it will not touch any objects. 1. Check that the battery (16) is in (see “Assembly instructions - In- serting the battery”). 2. To turn on, use your thumb to actuate the switch lock (3), then press the On/Off switch (2). Re- lease the switch lock. 3. To turn off, release the On/Off switch (2). There is no continu- ous operation mode. After turning off the appliance, the trimming assembly will keep revolving for some time. Allow the trimming assembly to come to a standstill. Neither touch nor slow down the moving cutting insert. Risk of injury! Trimmer settings The auxiliary handle can be set to various positions. Adjust the handle such that the cutting disk slightly tilts forward in your

and move the auxiliary handle (5) to your favourite position. Tighten the screw in the handle. The telescopic shaft allows you to adjust the appliance to your personal size. d Loosen the threaded bush (8). Adjust the telescopic shaft (9) to the correct length and tighten the threaded bush. Changing the cutting angle lets you trim e.g. under benches or wall offsets. e Tread on the pedal (15) on the motor housing and tilt the telescopic shaft (9). There are 4 preset tilt angles (see “Work instructions”). The handle rod can be turned by 90° and 180° (see “Work instructions”). f Push down the lock (7) and turn the handle rod 0° 90° 180° (6) until it snaps into your favourite position. The spacer bow keeps the trimming as- sembly away from plants and trunks not to be cut. g Flap the spacer bow (11) down. When the spacer bow is not in use you can tip it back up into its parking position. Manner of operation • Do not cut moist or wet grass. • Prior to starting the appliance, check that the cutting disk does not contact stones, gravel or other foreign bodies. • Switch on the trimmer before you approach the grass that is to be cut. • Do not overload the trimmer dur- ing operation. • Avoid contact with obstacles (stones, walls, fences, etc.) as this will rapidly wear out the lines. Cutting grass Cut the grass by swaying the trimmer sideways to the right and left. Cut slowly while the trimmer is tilted forwards by approx. 30°. Cut tall grass by a series of levels from

Be particularly careful and at - tentive when holding the cutting disk vertically. To avoid injuries, keep enough distance to the trimming assembly. Setup for vertical trimming: Move the appliance to the right and left in a slow swinging motion to trim slopes and steep inclines. • Handle rod: 180° (see f ) • Cutting angle: 0° (see e ) • Spacer bow in parking position Setup for edge trimming: To trim lawn edges, slowly move the appliance along the lawn edges. • Handle rod: 90° (see f ) • Cutting angle: 90° (see e) • Spacer bow in parking position Cleaning and maintenance Contact our Service Centre about repairs and servicing not described in this manual. Only use OEM parts. Risk of injury! Turn off the appliance and, before doing any servicing, remove the battery. The following cleaning and servicing should be done regularly. This will ensure a long and reliable service life. Cleaning Do not spray the appliance with wa- ter and do not immerse it in water. Electric shock hazard! • Keep clean the ventilation slots, motor housing and handles of the appliance. Use a damp cloth or a brush. Do not use cleaning agents or sol- vents. You may otherwise irreparably damage the appliance. • After every trimming session, remove grass and soil from the protective cover and the trimming assembly. • To thoroughly clean the trimming as- sembly, remove the cutting insert ( 13) (see “Replacing the cutting insert”) and use a sharp knife to clean the pin ( 23). General maintenance • Prior to every use, check the appli- ance for obvious defects such as loose, worn or damaged parts. Check that the screws in the cutting disk are tight. • Check covers and safety devices for damages and correct installation. Re- place as necessary. Replacing the cutting insert 1. Slide the cutting insert (13) in- ward and push it out of the pin (23) on the cutting disk (12). 2. Place the new cutting insert (13) on the pin (23) and pull out the insert until it snaps in. Storage • Store the trimmer in a dry place well out of reach of children.

they will be recycled in an environmen- tally friendly manner. For information about this, ask your local waste man- agement company or our service centre. Throw the cut grass on the compost. Do not throw it in the normal household waste. Guarantee The product has 2 years guarantee, for battery warranty, please check with our Technical Service. Damages due to natural wear and tear, due to overload or due to incorrect use are excluded from the guarantee. Certain components are subject to normal wear and tear and are excluded from the guarantee : this specifically applies to the cutting insert (plastic blade) and battery. Furthermore, another prerequisite for guarantee services is references indicated in this instructions manual regarding cleaning and maintenance have been adhered to. • Do not stand the trimmer on its pro- tective cover. Suspend it by its upper handle in such a manner that the protective cover does not come into contact with other objects. This is be- cause the protective cover could be- come deformed, thereby changing its dimensions and its safety properties. • In order to keep the battery well charged, avoid exposing the appli- ance to extreme heat or cold in stor- age. • • • • • Remove the battery before storing the unit for longer periods of time. Disposal and protection of the environment Remove the battery from the device and take the device, battery, accessories and packaging for environmentally friendly recycling. Machines do not belong with domes- tic waste. • Return the unit to a recycling centre. The plastics and metals in the unit can be sorted and appropriately recycled. Ask our Service Centre for details. Do not dispose of batteries in - plosion) or water. Damaged batter- ies may damage the environment and your health if toxic fumes or liquids leak out. • Dispose of batteries in discharged condition. We recommend covering the pole with adhesive tape to prevent a short circuit. Do not open up the battery. • Dispose of batteries in accordance with the local regulations. Take batteries to Please always check all the precise terms of the guarantee with our After Sale Service. Li-ion

number of the spare part with your order. Cutting inserts........................... Battery ...................................... Battery charger ......................... If further spare parts should be necessary, drawing. Technical data Appliance Motor voltage .............................24 V Capacity ...................................... 1.3 Ah Idling speed ................10300 min-1 (rpm) Protection Class ................................. III Runtime ..............................max. 30 min Cutting circle ................................25 cm Weight .........................................2.8 kg Sound pressure level (LpA) ....................... 70.3 dB (A) Sound power level (LwA) guaranteed............................96 dB(A) measured ...... 90.3 dB(A); K =3.2 dB(A) Vibration (an) .......................................... upper handle .............................2.0 m/s2 additional handle .......................2.5 m/s2 Battery (Li-on) Nominal voltage .........................24 V Capacity ...................................... 1.3 Ah Charging time ................... approx. 3-5 h Recharger Uptake voltage ........ 100-240V~50/60Hz Nominal consumption....................13 W Voltage output ............................24 V Recharging curren.........................0.5 A Protection class .............................. II Protection category ........................ ........................ IP20 * The actual runtime under load of a fully char- ged battery depends on how you work and on the load put on the trimmer during operation. Noise and vibration values have been de- termined according to the standards and regulations mentioned in the declaration of conformity. Technical and optical changes may be undertaken in the course of further de- velopment without notice. All dimensions, references and information in this instruc- tion manual are therefore not guaranteed. Legal claims made on the basis of the instruction manual can therefore not be considered as valid.

Battery not in Insert battery (see „Operation“) On/Off switch defective Send in to Service Centre for repair Motor defective Intermittent opera- tion Internal loose contact Send in to Service Centre for repair On/Off switch defective Much vibration Loud noise Cutting insert broken Replace cutting insert (see „Cleaning and servicing“) Trimming assembly dirty Clean trimming assembly (see „Clean- ing and servicing“) Motor defective Send in to Service Centre for repair Bad trim Cutting insert broken Replace cutting insert (see „Cleaning and servicing“) Trimming assembly dirty Clean trimming assembly (see „Clean- ing and servicing“) Battery not fully charged Recharge battery (see „Charging“) Charging not pos- sible. on the battery char- ger) Battery not placed in bat- tery charger properly Insert battery correctly (see „Charging“) Battery charger not plugged into mains prop- erly Plug into mains outlet correctly Battery contacts dirty Clean contacts Battery defective Replace battery (see „Spares“) Battery charger defective Replace battery charger (see „Spares“)

EC declaration of conformity Suzhou Cleva Electric Appliance Co., Ltd. No.8, Ting Rong Street, 215122 Suzhou, Jiangsu Province CHINA (MODEL: CLGT2425 ) L951145 ELECTRIC LAWN TRIMMER We Declare that the product Complies with the essential health and safety requirements of the following directives: - The Machinery Directive 2006/42/EC - The EMC Directive 2004/108/EC - The Outdoor Noise Directive 2000/14/EC & 2005/88/EC Measured Sound Power Level: 90.3 dB(A) • Guaranteed Sound Power Level: 96 dB(A) • - The RoHS Directive 2011/65/EU The conformity assessment followed was according to Directive 2000/14/EC, Annex V, and the Directive 2005/88/EC. Authorized Signatory and technical file holder Name: Will Zhou For and on behalf of Suzhou Cleva Electric Appliance Co., Ltd. Date: 01/04/2014 All technical information is held at the address detailed above