Larson Electronics EXP-TP-RL-1XFX5R Instruction Manual

Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com 1 of 2 Explosion Proof Rechargeable LED Flashlight Tripod Mounted - 5 Light Patterns - Intrinsically Safe Instruction Manual Thank you for choosing the EXP-LED-RL-FX5R rechargeable lantern. Please read this instruction manual before using your EXP-LED-RL-FX5R lantern. It includes important operating and safety instructions. NOTE: Charge the EXP-LED-RL-FX5R Lantern overnight before first use. SAFETY NOTICES • CAUTION: To reduce the risk of explosion, fire, and electrical shock or injury, DO NOT charge your EXP-LED-RL-FX5R lantern in a hazardous environment. ONLY CHARGE THE EXP-LED-RL- FX5R LANTERN IN NON-HAZARDOUS ENVIRONMENTS. • DO NOT attempt to recharge your EXP-LED-RL-FX5R Lantern in any charger other than the one supplied. • DO NOT attempt to charge any other product with your with the EXP-LED-RL-FX5R Charge Rack • NEVER leave your EXP-LED-RL-FX5R Lantern on with its lamp face against any surface, including skin, while the lantern is turned on. The heat buildup may cause burns and or fire. • Careful observation of the charge rack LEDs serves as an important warning of possible malfunction which may cause battery overcharging. The red LED should be on while the lantern is in the Charge Rack and charging. When fully charged, the red LED turns off and the green LED turns on. The Lantern is ready for operation. If the red LED blinks, remove the Lantern from service. • In extremely rare circumstances, an overcharged battery may produce a flammable hydrogen gas. In the unlikely event that this gas should ignite, personal injury could result. • The EXP-LED-RL-FX5R should note be turned on and off in the Charge Rack. • PLEASE recycle the battery. • DO NOT INCINERATE THE BATTERY. IT CAN EXPLODE IN A FIRE. • Handle the battery carefully. Never allow it to short circuit. It can deliver hundreds of Amperes of current and cause a fire. CHARGE RACK AND CHARGING • To release the Lantern from the rack, squeeze the on-off switch of the Lantern and lift the Lantern up and out of the Charge Rack. • To charge the Lantern, simply place the Lantern into the Charge Rack. It automatically locks in place and starts charging. CHARGE RACK MOUNTING The charge rack is mounted by removing the 2 mounting screws at the top of the charge rack and sliding the metal mounting bracket off the charge rack, then using 4 screws or bolts, attach the metal rack to the desired surface, then slide the charge rack on to the metal mounting bracket and replace the 2 mounting screws in the top of the charge rack. POWER SUPPLY 1. Never directly wire any Charge Rack directly to any 120 volt AC power source. It is intended for 12-15 volt DC only. 2. Make sure that the installation is fused. 2 amps per unit are recommended.

Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com 2 of 2 VEHICLE POWER REQUIREMENTS Maximum ampere draw from a completely discharged lantern is 2 Amps for the first 10 hours and .035 Amps from then on. Nominal charging current is 1 Amp. USAGE TEMPERATURE -24°C (-11.2°F) to +44°C (+111.2°F) USING THE TRIPOD 1. To assemble the tripod, begin by loosening the black adjustment knob on the tripod base. Slide the center pole through the adjustment sleeve until the legs are fully deployed. Tighten adjustment knob so legs stay fixed in place. 2. Connect the single Deutsch connector coil cord to light. 3. Loosen black adjustment knob for each sleeve to extend tripod. Extend top pole, then bottom pole when elevating. 4. Tighten adjustment knob once desired height is achieved. 5. Attach power cord to charge lamp. Charge requires at least 8 hours. OPERATION The light head features an Explosion Proof Rechargeable LED Flashlight. It is powered by the power switch located under the handle and will illuminate up to 10 hours. Do not look directly into lens when powering. Lamp head can be adjusted in multiple directions. Simply lift up on lamp head for vertical tilt and rotate. Modes: Lamp features the following modes. To select a mode, hold down the power button until the desired mode is achieved. A second press of the power button will turn off the light. Front Lamp Mode Rear Signal Lamp Mode 1 X STEADY X STEADY 2 X STEADY - OFF 3 X STEADY X STROBE 4 X STEADY X ROTATING 5 X S.O.S. X S.O.S. USE AND CARE Always check damaged or worn out parts before using the work light. When work light is not in use, store it in a secure place out of the reach of children. Inspect for good working condition prior to storage and before re-use. Should further information not covered by these instructions be required, please contact Larson Electronics at 1-800-369-6671 or [email protected] for further assistance. Please visit LarsonElectronics.com for Warranty and Return information. - Light Head Adjustment Points -Leg Sleeve Base Removal & Power Switch