Hubbell Laredo Installation Instructions

CAUTION: FIXTURE WEIGHTS ABOUT 30 POUNDS • Using template (A) lay over junction box (B) on the wall. Mark at (3) hole. (See Fig.1) • Drill wall for the hardware appropriate for the type wall. Use 1/4 diameter bolt. • Pull the supply wires (C) from junction box (B) . STEP II FIXTURE MOUNTING PREPARATION (See Fig. 2) • To open door (E), loosen (2) retaining screws (F). • For optional quick release door latch, push pin (D) to open door (E). • Loosen (4) screws (X) and them remove reflector (H). • Loosen screws (O), remove cover (P) and discard. STEP III FIXTURE MOUNTING (See Fig.3) • Insert all wires (C) through slit on gasket opening at the back of housing. • Hang fixture on the mounting hardware at the wall through key-slots opening (J). • Tighten bolts (K) securely. • Apply caulking sealant around the top and two sides of the housing. Step IV WIRING (See Fig. 3) • POWER MUST BE OFF. (WIRING MUST BE PERFORMED BY A QUALIFIED ELECTRICIAN) • Wire service leads to fixture power leads according to local and National Electric Codes. • For direct wire connections, connect ground wire to green wire then push ware back to J-box on the wall. Connect black to black and white to neutral then push connections back inside J-box (B). • When supplied with optional terminal block (L) or fuseblock (M) connect service leads to these devices. FOR THROUGH WIRING USING CONDUIT • Remove hole plug (N) for the conduit entry • Use pipe sealant before engaging conduit fittings to prevent water leakage. • Loosen screw (O) and remove wire cover (P). • Insert fixture lead wires (Q) through grommet ( R ). • Make the wire connections. • Replace cover (P) making sure not to pinch wires. INSTALLATION INSTRUCTIONS FOR WALLPACK LUMINAIRE Outdoor Lighting laredo WARNING: DISCONNECT POWER BEFORE INSTALLATION OR MAINTENANCE. READ INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO INSTALL LUMINAIRE, FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE. RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.

• Make sure that the lamp size and type matches the ballast specifications. • Replace reflector (H). • Engage the lamp to socket (S). • For medium base lamps – to ensure proper contact, loosen the lamp one turn then retighten. STEP VI RE-LAMPING USING POLE STICK (By others) (See Fig.4) CAUTION: WEAR SAFETY GOGGLES IN THE EVENT LAMP BREAKS • Using the other end of the pole, push latch pin (D) and slowly lower the door to open position. • Align lamp changer (U) with the lamp, then slowly push up to engage. Unscrew to remove lamp. • Attach the replacement lamp to head changer (U), align with the socket and screw in to engage. • To close door use again the other end of the pole, raise the front end of the door up to engage latch. REMOVING FRONT DIRECTOR FOR IMPROVING FORWARD THROW BEAM DISTRIBUTION. • Loosen (4) retaining screws (X) and remove reflector (H). • Unbend the two tabs to remove the front director (Z). STEP VII INSTALLING VANDAL SHIELD (See Fig. 5) • Open door (E) by loosening retaining screws (F). • From the inside on each (4) bosses adjacent to the lens clips, drill the door through using .173” diameter No.17 drill bit. • Install vandal shield (Y) using (4) self-threading screws (V) provided. • Remove metal chips and replace door. STEP VIII PBT PHOTOCONTROL FIELD INSTALLATION (See Fig. 6) • Remove hole plug (N) from the side of housing. • Install photocontrol switch (PC) from the inside of housing using gasket (gg) and nut (nn). PT. NO. 93002010 Outdoor Lighting laredo INSTALLATION INSTRUCTIONS FOR WALLPACK LUMINAIRE