Kontron SYMKLOUD MS2900 Getting Started

switch(config)#spanning-tree extend system- id switch(config)#interface vlan 10 switch(config-if)# ip address 192.168.101.254 255.255.255.0 switch(config-if)#exit switch(config)# interface gigabitEthernet 0/1 switch(config-if)#switchport trunk encapsulation dot1q switch(config-if)#switchport mode trunk switch(config-if)#switchport trunk native vlan 1 switch(config-if)#switchport trunk allowed vlan add 1,10 switch(config-if)#speed 1000 switch(config-if)#duplex full switch(config-if)#end switch# From privileged EXEC mode, enter global configuration mode. Configure spanning-tree mode to PVST. Enable extend system-id. Enter interface VLAN configuration mode. Define VLAN 10 IP address and subnet. Exit interface configuration mode. Enter interface 0/1 configuration mode. Configure dot1q encapsulation (IEEE 802.1Q is a standard protocol for interconnecting multiple switches and routers and for defining VLAN topologies). Configure interface mode to trunking layer 2 VLAN port. Define the native VLAN 1 for a trunk interface. Add VLAN 1 and 10 to the allowed VLAN list. Configure the speed of a given Ethernet interface to 1Gbps. Force full-duplex operation. Return to Privileged EXEC mode.  

Username:admin Password:admin # Use HOTKEY to redirect serial console multiplexer to the switch CLI.

(config)# vlan 4093 (config-vlan)# no name (config-vlan)# exit (config)# vlan 10 (config-vlan)# name managementanddata (config-vlan)# end # Enter configuration mode Enter VLAN 4093 (default management) database entry Remove the name Exit VLAN 4093 database entry Create VLAN 10 in the VLAN database Enter a name for VLAN 10 Exit configuration mode # configure terminal (config)# interface vlan 4093 (config-if-vlan)# no ip address (config-if-vlan)# exit (config)# interface vlan 10 (config-if-vlan)# ip address 192.168.101.10 255.255.255.0 (config-if-vlan)# end # Enter configuration mode Enter default management VLAN interface configuration mode Remove default IP address Exit default management interface configuration mode Enter VLAN 10 interface configuration mode Configure VLAN 10 IP address and subnet Exit Interface configuration mode # configure terminal (config)# interface vlan 4093 (config-if-vlan)# no ip address (config-if-vlan)# exit (config)# interface vlan 10 (config-if-vlan)# ip address dhcp (config-if-vlan)# end # Enter configuration mode Enter default management VLAN interface configuration mode Remove default IP address Exit default management interface configuration mode Enter VLAN 10 interface configuration mode Configure VLAN 10 IP to use DHCP Exit Interface configuration mode # configure terminal (config)# interface Ethernet 1/3 (config-if)# switchport hybrid allowed vlan add 10 (config-if)# exit (config)# interface Ethernet 1-2/7-24 (config-if)# switchport hybrid allowed vlan add 10 (config-if)# exit Enter configuration mode Enter 1/3 uplink interface configuration mode. Add VLAN 10 to the allowed hybrid mode VLAN list Exit the interface configuration mode Enter 1/7-24 and 2/7-24 interfaces (MSP nodes) configuration mode. Add VLAN 10 to the allowed hybrid mode VLAN list Exit the interface configuration mode

(config-if)# switchport hybrid allowed vlan add 10 (config-if)# end # Enter 1/26 and 2/26 ShMC interfaces configuration mode. Add VLAN 10 to the allowed hybrid mode VLAN list Exit configuration mode # copy running-config startup-config Building configuration... % Saving 3930 bytes to flash:startup-config # Save the running-config to startup-config. # configure terminal (config)# spanning-tree mst name SYMKLOUD revision 0 (config)# spanning-tree mst 1 vlan 10 (config# end # Enter configuration mode Enter the region name and revision Create MSTP instance 1 and assign VLAN10 to it Exit configuration mode

VLAN1 LINK: 00-a0-a5-a6-8c-fa Mtu:1500 IPv6: fe80::2a0:a5ff:fea6:8cfa/64 IPv4: 192.168.101.10/24 192.168.101.255 Display configuration settings associated with the switch's network interface. # ping ip 192.168.101.254 PING server 192.168.101.254, 56 bytes of data. 64 bytes from 192.168.101.254: icmp_seq=0, time=0ms 64 bytes from 192.168.101.254: icmp_seq=1, time=0ms 64 bytes from 192.168.101.254: icmp_seq=2, time=0ms 64 bytes from 192.168.101.254: icmp_seq=3, time=0ms 64 bytes from 192.168.101.254: icmp_seq=4, time=0ms Sent 5 packets, received 5 OK, 0 bad Ping external network using the management IP of the ToR switch.

Password: admin ipmitool> Use HOTKEY to redirect serial console multiplexer to the ShMC CLI.

ipmitool> mc reset cold Assign VLAN 10 on the ShMC. Reboot the ShMC ipmitool> lan set 1 ipsrc static ipmitool> lan set 1 ipaddr 192.168.101.1 ipmitool> lan set 1 netmask 255.255.255.0 ipmitool> lan set 1 defgw ipaddr 192.168.101.254 Configure IP source to static. Define static IP address. Define netmask. Define default gateway IP address. ipmitool> lan set 1 ipsrc dhcp Configure IP source to DHCP. ipmitool> lan print Access Mode : Enable IP Address Source : Static IP Address : 192.168.101.1 Subnet Mask : 255.255.255.0 MAC Address : 00:a0:a5:96:e9:ea IP Header : TTL=0x40 Flags=0x40 Precedence=0x00 TOS=0x10 Default Gateway IP : 192.168.101.254 Default Gateway MAC : 00:00:00:00:00:00 802.1q VLAN ID : 10 802.1q VLAN Priority : 0 HPM.2 Draft Capabilities: Supported Hostname (OEM) : Display the current network configuration.

Password:admin ipmitool> Enter the default credential to access the standby ShMC. ipmitool> set targetaddr 0x10 Set remote target address of the standby ShMC. The following command will be redirected to the targeted address. ipmitool> lan set 1 vlan id 10 ipmitool> mc reset cold Assign VLAN 10 on the ShMC. Reboot the ShMC ipmitool> lan set 1 ipsrc static ipmitool> lan set 1 ipaddr 192.168.101.2 ipmitool> lan set 1 netmask 255.255.255.0 ipmitool> lan set 1 defgw ipaddr 192.168.101.254 Configure IP source to static. Define static IP address. Define netmask. Define default gateway IP address.

Configure IP source to DHCP. ipmitool> lan print Access Mode : Enable IP Address Source : Static IP Address : 192.168.101.2 Subnet Mask : 255.255.255.0 MAC Address : 00:a0:a5:96:e9:ea IP Header : TTL=0x40 Flags=0x40 Precedence=0x00 TOS=0x10 Default Gateway IP : 192.168.101.254 Default Gateway MAC : 00:00:00:00:00:00 802.1q VLAN ID : 10 802.1q VLAN Priority : 0 HPM.2 Draft Capabilities: Supported Hostname (OEM) : Display the current network configuration.

CentOS Linux 7 (Core) Kernel 3.10.0-229.el7.x86_64 on an x86_64 sk9013075860 login: Ctrl+gg 0 MSP80XX login: admin Password: ipmitool> Use HOTKEY to redirect serial console multiplexer to the MSP node 1 components. Use HOTKEY to redirect serial console multiplexer to the BMC of MSP node 1. ipmitool> set targetaddr 0x82 Set remote target address to the BMC of MSP node 1. The following commands will be redirected to the targeted address. ipmitool> lan set 1 vlan id 10 ipmitool> mc reset cold Assign VLAN 10 on the BMC. Reboot the BMC ipmitool> lan set 1 ipsrc static ipmitool> lan set 1 ipaddr 192.168.101.11 ipmitool> lan set 1 netmask 255.255.255.0 ipmitool> lan set 1 defgw ipaddr 192.168.101.254 Configure IP source to static. Define static IP address. Define netmask. Define default gateway IP address.

Configure IP source to DHCP. ipmitool> lan print Access Mode : Enable IP Address Source : Static IP Address : 192.168.101.11 Subnet Mask : 255.255.255.0 MAC Address : 00:a0:a5:90:ac:d0 IP Header : TTL=0x40 Flags=0x40 Precedence=0x00 TOS=0x10 Default Gateway IP : 192.168.101.254 Default Gateway MAC : 00:00:00:00:00:00 802.1q VLAN ID : 10 802.1q VLAN Priority : 0 HPM.2 Draft Capabilities: Supported Hostname (OEM) : Display the current network configuration. # Ctrl+g 0 MSH8900 Login: admin Password: admin ipmitool> Use HOTKEY to redirect serial console multiplexer to the ShMC CLI.

lan set 1 ipsrc static lan set 1 vlan id 10 lan set 1 ipaddr 192.168.101.11 lan set 1 netmask 255.255.255.0 lan set 1 defgw ipaddr 192.168.101.254 mc reset cold set targetaddr 0x84 lan set 1 ipsrc static lan set 1 vlan id 10 lan set 1 ipaddr 192.168.101.12 lan set 1 netmask 255.255.255.0 lan set 1 defgw ipaddr 192.168.101.254 mc reset cold set targetaddr 0x86 lan set 1 ipsrc static lan set 1 vlan id 10 lan set 1 ipaddr 192.168.101.13 lan set 1 netmask 255.255.255.0 lan set 1 defgw ipaddr 192.168.101.254 mc reset cold set targetaddr 0x88 lan set 1 ipsrc static lan set 1 vlan id 10 lan set 1 ipaddr 192.168.101.14 lan set 1 netmask 255.255.255.0 lan set 1 defgw ipaddr 192.168.101.254 mc reset cold set targetaddr 0x8a lan set 1 ipsrc static lan set 1 vlan id 10 lan set 1 ipaddr 192.168.101.15 lan set 1 netmask 255.255.255.0 lan set 1 defgw ipaddr 192.168.101.254 mc reset cold set targetaddr 0x8c lan set 1 ipsrc static lan set 1 vlan id 10 lan set 1 ipaddr 192.168.101.16 lan set 1 netmask 255.255.255.0 lan set 1 defgw ipaddr 192.168.101.254 mc reset cold set targetaddr 0x8e lan set 1 ipsrc static lan set 1 vlan id 10 lan set 1 ipaddr 192.168.101.17 lan set 1 netmask 255.255.255.0 lan set 1 defgw ipaddr 192.168.101.254 mc reset cold set targetaddr 0x90 lan set 1 ipsrc static Target BMC of MSP node 1. Configure IP source to static. Assign VLAN 10 on the BMC. Define static IP address. Define netmask. Define default gateway IP address. Reboot the BMC Target BMC of MSP node 2. Configure IP source to static. Assign VLAN 10 on the BMC. Define static IP address. Define netmask. Define default gateway IP address. Reboot the BMC Target BMC of MSP node 3. Configure IP source to static. Assign VLAN 10 on the BMC. Define static IP address. Define netmask. Define default gateway IP address. Reboot the BMC Target BMC of MSP node 4. Configure IP source to static. Assign VLAN 10 on the BMC. Define static IP address. Define netmask. Define default gateway IP address. Reboot the BMC Target BMC of MSP node 5. Configure IP source to static. Assign VLAN 10 on the BMC. Define static IP address. Define netmask. Define default gateway IP address. Reboot the BMC Target BMC of MSP node 6. Configure IP source to static. Assign VLAN 10 on the BMC. Define static IP address. Define netmask. Define default gateway IP address. Reboot the BMC Target BMC of MSP node 7. Configure IP source to static. Assign VLAN 10 on the BMC. Define static IP address. Define netmask. Define default gateway IP address. Reboot the BMC Target BMC of MSP node 8. Configure IP source to static.

lan set 1 ipaddr 192.168.101.18 lan set 1 netmask 255.255.255.0 lan set 1 defgw ipaddr 192.168.101.254 mc reset cold set targetaddr 0x92 lan set 1 ipsrc static lan set 1 vlan id 10 lan set 1 ipaddr 192.168.101.19 lan set 1 netmask 255.255.255.0 lan set 1 defgw ipaddr 192.168.101.254 mc reset cold set targetaddr 0x20 Assign VLAN 10 on the BMC. Define static IP address. Define netmask. Define default gateway IP address. Reboot the BMC Target BMC of MSP node 9. Configure IP source to static. Assign VLAN 10 on the BMC. Define static IP address. Define netmask. Define default gateway IP address. Reboot the BMC Target active ShMC IPMI address. set targetaddr 0x82 lan set 1 vlan id 10 lan set 1 ipsrc dhcp mc reset cold set targetaddr 0x84 lan set 1 vlan id 10 lan set 1 ipsrc dhcp mc reset cold set targetaddr 0x86 lan set 1 vlan id 10 lan set 1 ipsrc dhcp mc reset cold set targetaddr 0x88 lan set 1 vlan id 10 lan set 1 ipsrc dhcp mc reset cold set targetaddr 0x8a lan set 1 vlan id 10 lan set 1 ipsrc dhcp mc reset cold set targetaddr 0x8c lan set 1 vlan id 10 lan set 1 ipsrc dhcp mc reset cold set targetaddr 0x8e lan set 1 vlan id 10 lan set 1 ipsrc dhcp mc reset cold set targetaddr 0x90 lan set 1 vlan id 10 lan set 1 ipsrc dhcp mc reset cold set targetaddr 0x92 lan set 1 vlan id 10 lan set 1 ipsrc dhcp mc reset cold set targetaddr 0x20 Target BMC of MSP node 1. Assign VLAN 10 on the BMC. Configure IP source to DHCP. Reboot the BMC Target BMC of MSP node 2. Assign VLAN 10 on the BMC. Configure IP source to DHCP. Reboot the BMC Target BMC of MSP node 3. Assign VLAN 10 on the BMC. Configure IP source to DHCP. Reboot the BMC Target BMC of MSP node 4. Assign VLAN 10 on the BMC. Configure IP source to DHCP. Reboot the BMC Target BMC of MSP node 5. Assign VLAN 10 on the BMC. Configure IP source to DHCP. Reboot the BMC Target BMC of MSP node 6. Assign VLAN 10 on the BMC. Configure IP source to DHCP. Reboot the BMC Target BMC of MSP node 7. Assign VLAN 10 on the BMC. Configure IP source to DHCP. Reboot the BMC Target BMC of MSP node 8. Assign VLAN 10 on the BMC. Configure IP source to DHCP. Reboot the BMC Target BMC of MSP node 9. Assign VLAN 10 on the BMC. Configure IP source to DHCP. Reboot the BMC Target active ShMC IPMI address.

lan print set targetaddr 0x84 lan print set targetaddr 0x86 lan print set targetaddr 0x88 lan print set targetaddr 0x8a lan print set targetaddr 0x8c lan print set targetaddr 0x8e lan print set targetaddr 0x90 lan print set targetaddr 0x92 lan print set targetaddr 0x20 Confirm configuration of the BMC of MSP node 1. Confirm configuration of the BMC of MSP node 2. Confirm configuration of the BMC of MSP node 3. Confirm configuration of the BMC of MSP node 4. Confirm configuration of the BMC of MSP node 5. Confirm configuration of the BMC of MSP node 6. Confirm configuration of the BMC of MSP node 7. Confirm configuration of the BMC of MSP node 8. Confirm configuration of the BMC of MSP node 9. Redirect bridging to the active ShMC.