NAiS GT10 Technical Manual

Technical Manual PROGRAMMABLE DISPLAY GT10 Includes installation guide for GTWIN screen creation software. all-guides.co m

Before installing, operating, servicing or inspecting this product, please make sure you have read this manual and the explanations of how procedures are carried out, and make sure the product is used correctly. This manual uses two safety standard levels: ”WARNING” and ”CAUTION”. WARNING Erroneous handling of an item marked with this label can cause fatal or critical injury to the user. D If this product is used in applications where accidents involving bodily injury and/or significant damage may be conceivable, measures should be taken to ensure adequate safety, such as the use of duplicate safety mechanisms. D The functions of the GT10 should not be used to design systems which may pose a threat to human life or which may cause severe injury or damage. Designs should include safety mechanisms for use in the event that switch functions do not function correctly. D Do not use this product in an environment where combustible gases are present. This can cause explosion. D This product contains a secondary battery (lithium and vanadium). Do not dispose of it by incineration. This can cause it to explode. CAUTION Erroneous handling of an item marked with this label can cause injury to the user, or physical damage to property. D This product should not be used outside of the stated specifications ranges for ratings, service life, configuration factors and other elements. This can cause abnormal generation of heat and smoke. D The operational force of the touch panel should be kept to 0.98 N or lower. Operating the touch panel at a higher force could cause damage. D Never touch terminals while the power supply is on. This can cause electric shock. D Never disassemble or alter this product. This can cause electric shock and smoke generation.

GT10 Main Unit Before Using the GT10 for the First Time This section describes items that should be confirmed and precautions that should be observed before the GT10 is used for the first time. Chapter 1. Specifications This chapter contains the names and specifications of the various parts of the GT10, as well as a table of functions, wiring diagrams, and dimensions. Chapter 2. Installation and Wiring This chapter explains how the GT10 should be installed and how wiring should be connected. Chapter 3. Setup This chapter describes the setup procedures necessary when using the GT10 for the first time. Chapter 4. Connecting and Communicating with the PLC This chapter explains how to connect the GT10 to the PLC and the FP series by Matsushita, and how to set up communications between the units. Chapter 5. GT Configuration Settings This chapter describes the configuration settings for the GT10, and how they should be entered. Chapter 6. Using the Various Functions Functions such as switching GT10 screens, backlighting, and buzzer control are explained here. Chapter 7. Servicing and Maintenance This chapter describes servicing and maintenance procedures for the GT10, as well as how optional items are handled. Chapter 8. Troubleshooting This explains what to do if there appears to be something wrong with the GT10, or an error occurs. Chapter 9. Documentation This section includes BIN/HEX/BCD code correspondence tables, ASCII code tables, cable specifications, and other information. Screen Creation Tool Terminal GTWIN Before Using Terminal GTWIN for the First Time This section contains special precautions that should be read if you are using GTWIN for the first time. Chapter 1. Preparation This section explains how to install GTWIN in the personal computer, how to boot it, and how to exit it.

ii Table of Contents GT10 Main Unit Before Using the GT10 for the First Time GT10 Usage Procedures ix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Confirming the Package Contents xi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GT10 System Configuration xv . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Products for the GT10 Series xvii . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . An Overview of GT10 Functions xviii . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety Precautions xxi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Chapter 1 Specifications 1.1 GT10 Specifications 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1.1 General Specifications 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1.2 Display 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1.3 Functions 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1.4 Touch Key 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1.5 Memory (1) 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1.6 Memory (2) 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1.7 Interface 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2 Names and Functions of Parts 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2.1 GT10 (front) 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2.2 GT10 (rear) 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2.3 Names and Functions of Parts 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3 Internal Wiring Connections for Ports 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3.1 COM. Port 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3.2 TOOL Port 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3.3 Power Supply Terminals 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.4 Dimensional Outline Diagram 11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.4.1 GT10 Dimensional Outline Diagram 11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.4.2 Panel Cutout Dimensional Outline Diagram 12 . . . . . . . . . . . . . . . . . . . . .

GT10 iii Chapter 2 Installation and Wiring 2.1 Installation 15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.1.1 Installation Environment 15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.1.2 Installation Method 17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2 Wiring the Power Supply 19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2.1 Wiring the Power Supply 19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3 Wiring the COM. Port 21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3.1 Wiring the COM. Port 21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3.2 Wiring Method 22 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3.3 Precautions Concerning Wiring 22 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Chapter 3 Setup 3.1 Setup Procedure for the GT10 27 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.1.1 Setup Procedure 27 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.2 Entering Settings for the Basic Communication Area to PLC 30 . . . . . . . . . . . . . . 3.2.1 What is the Basic Communication Area? 30 . . . . . . . . . . . . . . . . . . . . . . . 3.2.2 Basic Communication Area Map 32 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Chapter 4 Connecting and Communicating with the PLC 4.1 Connecting the FP0 37 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.1.1 Connecting to the COM. Port 37 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.1.2 Connecting to the TOOL Port 39 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2 Connecting the FP1 40 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2.1 Connecting to the COM. Port 40 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3 Connecting the FP2/FP2SH 41 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3.1 Connecting to the COM. Port 41 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3.2 Connecting to the TOOL Port 42 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4 Connecting the FP2/FP2SH Computer Communication Unit 43 . . . . . . . . . . . . . . 4.5 Connecting the FP10SH 44 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5.1 Connecting to the COM. Port 44 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5.2 Connecting to the TOOL Port 46 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.6 Connecting the FP10SH/FP3 Computer Communication Unit 47 . . . . . . . . . . . . . 4.7 Connecting the FP-M 48 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.7.1 Connecting to the COM. Port 48 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.7.2 Connecting to the TOOL Port 50 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

iv 4.8 Automatic Communication Settings Function 51 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.9 Through Function 53 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Chapter 5 GT10 Configuration Settings 5.1 GT10 Configuration Settings 57 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.1.1 Two Types of GT10 Configuration Settings 57 . . . . . . . . . . . . . . . . . . . . . . 5.2 Entering Configuration Settings from GTWIN Screen Creation Tool 58 . . . . . . . . 5.2.1 Opening the GT Configuration Settings 58 . . . . . . . . . . . . . . . . . . . . . . . . . 5.2.2 GT Configuration Settings: “Basic Setup” 59 . . . . . . . . . . . . . . . . . . . . . . . 5.2.3 GT Configuration Settings: “Communication Parameters” 61 . . . . . . . . . 5.2.4 GT Configuration Settings: “Auto-Paging” 64 . . . . . . . . . . . . . . . . . . . . . . 5.2.5 GT Configuration Settings: “Startup Screen Settings” 66 . . . . . . . . . . . . . 5.2.6 GT Configuration Settings: “Setup” 68 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.2.7 GT Configuration Settings: “Hold PLC Device” 71 . . . . . . . . . . . . . . . . . . . 5.3 Entering Configuration Settings from the GT Main Unit 73 . . . . . . . . . . . . . . . . . . . 5.3.1 What is the System Menu? 73 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.3.2 Bringing Up the System Menu 73 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.3.3 Setting Mode: “Communication Parameters” (COM. Port / TOOL Port) 74 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.3.4 Setting Mode: “Liquid Crystal Display Contrast Adjustment” (Contrast) 76 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.3.5 Setting Mode: “Clock Settings” (Clock) 76 . . . . . . . . . . . . . . . . . . . . . . . . . 5.3.6 Setting Mode: “Memory Initialization” (Clear Memory) 78 . . . . . . . . . . . . 5.3.7 Test Mode: “Self-Diagnosis” 79 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.3.8 Inhibiting the System Menu Display 80 . . . . . . . . . . . . . . . . . . . . . . . . . . . . Chapter 6 How the Various Functions Are Used 6.1 Switching Screens 83 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.1.1 Switching the Screen from the PLC 83 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.1.2 Switching the Screen with the GT Main Unit 84 . . . . . . . . . . . . . . . . . . . . . 6.2 Basic Communication Area to PLC and Bit Device Functions 89 . . . . . . . . . . . . . 6.2.1 Bit Device Functions 89 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . all-guides.co m

GT10 v Chapter 7 Servicing and Maintenance 7.1 What the Internal Secondary Battery Does 93 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.1.1 The Function of the Secondary Battery 93 . . . . . . . . . . . . . . . . . . . . . . . . . 7.2 Replacing the Front Panel Protective Sheet 95 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.2.1 About the Front Panel Protective Sheet 95 . . . . . . . . . . . . . . . . . . . . . . . . 7.2.2 Replacing the Front Panel Protective Sheet 95 . . . . . . . . . . . . . . . . . . . . . 7.3 Replacing the Waterproof Packing 96 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.3.1 About the Waterproof Packing 96 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.3.2 Replacing the Waterproof Packing 96 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Chapter 8 Troubleshooting 8.1 What To Do If Something Unusual Occurs 99 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.2 Error Codes and How to Handle Them 102 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.2.1 About Error Codes 102 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.2.2 GT10 Error Codes 102 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.2.3 PLC Error Codes 103 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.3 Table of Screen Messages 104 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.3.1 Table of GT10 Screen Messages 104 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Chapter 9 Documentation 9.1 BIN/HEX/BCD Code Correspondence Table 107 . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.2 ASCII Code Table 108 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.3 Basic Communication Area Map 109 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.4 Dimensional Outline Diagrams 110 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.4.1 GT10 Dimensional Outline Diagram 110 . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.4.2 Panel Cutout Dimensional Outline Diagram 111 . . . . . . . . . . . . . . . . . . . . 9.5 Cable Specifications 112 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.5.1 PLC Communication Cable: Mini-DIN 5-pin Loose-Wire (AIGT8192) 112 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.5.2 PLC Communication Cable: D-sub 9-pin Loose-Wire Cable (AIP81842) 112 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

vi GTWIN Before Using Terminal GTWIN for the First Time Precautions Before Using GTWIN for the First Time 116 . . . . . . . . . . . . . . . . . . . . . . . . . Usage Environment and GT Main Unit Models that are Supported 116 . . . . . . . . Special Precautions 117 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Important Note About Saving Screen Data Files 117 . . . . . . . . . . . . . . . . . . . . . . . . Chapter 1 Preparation 1.1 Installing GTWIN 121 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1.1 Procedure for Installing GTWIN in a Personal Computer 121 . . . . . . . . . 1.2 Booting GTWIN 127 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2.1 Booting GTWIN 127 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2.2 Selecting the Working Menu 127 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2.3 Selecting the Model 127 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2.4 Entering Settings for the Basic Communication Area to PLC 128 . . . . . 1.3 Exiting GTWIN 129 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3.1 Exiting GTWIN 129 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.4 Procedures for Using GTWIN 130 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

This section describes items that should be confirmed and precautions that should be observed before the GT10 is used for the first time. Make sure you read this section before using the GT10. GT10 Usage Procedures ix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Confirming the Package Contents xi . . . . . . . . . . . . . . . . . . . . . . . . GT10 System Configuration xv . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Products for the GT10 Series xvii . . . . . . . . . . . . . . . . . . . . . . . . . . . An Overview of GT10 Functions xviii . . . . . . . . . . . . . . . . . . . . . . . . . Safety Precautions xxi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

GT10 ix GT10 Usage Procedures If you are using the GT10 for the first time, please follow the procedure outlined below. Procedure For Using the GT10 For the First Time 1. Confirm the items included with the product. page xi Please confirm that all of the items have been included with the product you have purchased. Products are carefully checked before being shipped, but if you do find anything missing, please contact your dealer. 2. Confirm the items listed under “Safety Precautions”. page xxi Before using your product, please make sure you read the items listed under “Safety Precautions”, in order to make sure your product is used safely. After reading the precautions, please make sure the product is used correctly. 3. Install and wire the main unit. page 15 Install the main unit, and connect the power supply, PLC connection cable and other wiring. When installing and wiring the product, carefully read the explanation on pages 15 to 18 concerning the installation environment, and make sure the product is installed correctly, in an appropriate environment. For information on connecting the product to the FP series PLC, and on entering communications settings, please see page 37 and subsequent pages. 4. Set up the main unit. page 27 When the product is shipped from the factory, it is set up with specifications that enable connection to the FP series PLC. If you plan to use the product without changing these settings, nosetup isrequired, but if youplanto changethe settings, you willneed to follow the setup procedure outlined on page 27 and subsequent pages. Particularly with regard to the basic communication area to the PLC and other devices, please confirm the settings carefully and change only those that are necessary. J Main cases in which setup is necessary · When the device being connected is a general-purpose serial device (such as a computer or microcomputer board) · When the basic communication area for the device is different from that set when the product is shipped 5. Check communication with the external device (PLC, etc.). page 37 Check the connections and communication with the external device. Connections and communication with devices in the FP series PLC vary depending on the device, so check the information on page 37 and subsequent pages. 6. Enter the operating environment settings. page 57 In addition to the setup described at step 4, various detailed settings can be entered for the GT10 operating environment. Enter any necessary operating environment settings, referring to page 57 and subsequent pages. 7. Install the screen creation tool. page 116 Install the Terminal GTWIN screen creation tool in the personal computer. Follow the instructions on page 116 and subsequent pages to install the software. all-guides.co m

x 8. Create the screen contents. Create the screen contents using the Terminal GTWIN screen creation tool, and send the screen to the GT10 main unit. For information on creating screens and on operating GTWIN, please refer to the Help function that comes with GTWIN. 9. Test the operation. Connect the GT10 containing the screen data to an external device (PLC or general-purpose serial device), and check the operation contents.

GT10 xi Confirming the Package Contents Check to make sure the necessary items have been included with the product you have purchased. Items Included With the GT10 (AIGT1000B) Main unit Set of attachment fittings Attachment fittings x 4 Attachment screws x 4 Front panel protective sheet There is a front panel protective sheet, available as an optional product, attached to the front panel of the unit. Installation instructions Please read these instructions carefully before using the product. Communication connector Waterproof packing One piece of waterproof packing has been attached to unit.

xii CAUTION • There is a film over the front panel protective sheet. Remove this film when using the unit. For instructions on removing the film, see page 95. • Front panel protective sheets for replacement are available as a separate purchase (AIGT180). Please see page xvii. • Waterproof packings for replacement are available as a separate purchase (AIGT181). Please see page xvii.

GT10 xiii Items Included With the Terminal GTWIN English-language version (AIGT8001) Terminal GTWIN CD-ROM Screen Transfer Cable (AFC8503) AFC8503 (3 m/9.84 ft) Software usage license agreement and user card Read the “Software usage license agreement” carefully, and fill in the user card. Please return the user card to Matsushita. GT10 Technical Manual This is the manual you are currently reading. It contains instructions on installing and booting GTWIN. Please read it carefully before using your product. CAUTION About the software usage license agreement and user card • Before using GTWIN, read the “Software usage license agreement” carefully. • The license agreement comes as a set with the user card. Fill in the user card, and return it to Matsushita. The user card is necessary in order to obtain support services such as future version upgrades and technical support. Don’t forget to return the card in order to be eligible for such services. • The serial number needed in order to install GTWIN is found on the user card. Please make a copy of it before returning the card, and keep it in a safe place.

xiv Items Included With the PLC Connection Cable (AIGT8192 / AIP81842) Cable One of the following two cables has been included with the product you have purchased. AIGT8192 (2 m/6.56 ft) AIP81842 (2 m/6.56 ft) Wiring diagram The package includes a diagram that shows the internal wiring of the cables pictured above. REFERENCE For information on connecting and wiring the cables shown above and the PLC, please refer to page 35, Chapter 4, “Connecting and Communicating With the PLC”. Items Included With the Front Panel Protective Sheet (AIGT180) Front panel protective sheet In order to protect the touch panel on the GT10 and keep it clean, one front panel protective sheet is included when the unit is shipped. If this front panel protective sheet is dirty or has become worn, it should be replaced. Replacement sheets are sold separately, in packages of ten. Installation instructions Please read these instructions carefully before installing the product. REFERENCE For information on replacing the front panel protective sheet, please refer to page 95. all-guides.co m

GT10 xv GT10 System Configuration The following devices are necessary in order to use the GT10. Connecting cable Screen transfer cable D-sub 9-pin - mini-DIN 5-pin (3 m/9.84 ft) Product No.: AFC8503 * One cable is included with GTWIN English-lan- guage version. Commercially available personal computer Screen creation tool Terminal GTWIN English-language version Windows 95/98/2000/NT supported GTWIN CD-ROM Screen transfer cable (AFC8503) GT10 Technical Manual included as accessory Product No.: AIGT8001 GT10 STN monochrome liquid crystal display Product No.: AIGT1000B Main unit Communication cable PLC connecting cable (1) For connection to TOOL port of FP0 / FP2 / FP2SH / FP-M Mini-DIN 5-pin loose-wire cable (2 m/6.56 ft) Product No.: AIGT8192 Connecting to the TOOL port of the FP0 / FP2 / FP2SH / FP-M Communication cable PLC connecting cable (2) For connection to COM. port of FP1 / FP2 / FP2SH / FP-M / FP10SH, TOOL port of FP10SH, and computer communication unit of FP2 / FP3 D-sub 9-pin loose-wire cable (2 m/6.56 ft) Product No.: AIP81842 Connecting to the COM. port of FP1 / FP2 / FP2SH / FP-M / FP10SH, TOOL port of FP10SH, and computer communication unit of FP2/FP3

xvi CAUTION Connecting to the COM. port of the FP0 Because connecting the unit to the COM. port of the FP0 requires a loose-wire connection, this cable is not available. For more detailed information, please see “Connecting the FP0” on page 37.

GT10 xvii Products for the GT10 Series Products types Item Name Contents Product No. GT10 main unit Programmable display unit GT10 main unit AIGT1000B Terminal GTWIN English-language version - “Terminal GTWIN” English-language screen creation tool (CD-ROM) - Set of GT10 Technical manuals (English) AIGT8001 Screen transfer cable Cable for transferring cable between GTWIN and GT10 (included with Terminal GTWIN English-language version) (3 m/9.84 ft) AFC8503 PLC connecting cable (1) For connection to TOOL port of FP0 / FP2 / FP2SH / FP-M Mini-DIN 5-pin loose-wire cable (2 m/6.56 ft) AIGT8192 PLC connecting cable (2) For connection to COM. port of FP1 / FP2 / FP2SH / FP-M / FP10SH, TOOL port of FP10SH, and computer communication unit of FP2 / FP3 D-sub 9-pin loose-wire cable (2 m/6.56 ft) AIP81842 Front panel protective sheet Front panel protective sheet for GT10 (for replacement). Ten in set. * 1 sheet included with GT10 when shipped. AIGT180 Waterproof packing Waterproof packing for GT10 (for replacement). Ten in set. * 1 piece included with GT10 when shipped. AIGT181 CAUTION • Connecting to the COM. port of the FP0 Because connecting the unit to the COM. port of the FP0 requires a loose-wire connection, this cable is not available. For more detailed information, please see “Connecting the FP0” on page 37. • About the manual packed with the Terminal GTWIN English-language version The manual you are currently reading is included as an accessory with the Terminal GTWIN English-language version. This manual contains information only on procedures such as installing GTWIN. For detailed information on operating GTWIN, please refer to the Help function in the software.

xviii An Overview of GT10 Functions 3 colors can be displayed, to reflect the status Various messages and graphics can be displayed on the liquid crystal display screen, which measures 160 x 64 dots, as well as lamps, internal PLC data, graphs, clocks, and other information. In addition,backlighting isavailableinthree colors, green, orange, and red, so that information can be color-coded. This makes it easy to grasp information at a glance. Red Green Orange High-resolution touch panel provided A compact touch panel is provided with on-screen switches and a keyboard, letting you operate the unit simply by touching the screen. This high-resolution touch panel is fitted with 20 horizontal and 8 vertical segments, so that numerous switches can be used, and allows maximum flexibility in the switch layout.

GT10 xix Screens can be created easily, using special tools Screen contents can be easily created using the dedicated Terminal GTWIN tool (runs on Windows 95/98/2000/NT). Screens are put together simply by selecting parts from a library and positioning them in place. all-guides.co m

xx Ultra-thin body is only 32 mm/1.26 inch deep The in-panel depth is a mere 32 mm/1.26 inch (including the fittings), configuring an ultra-thin body and taking up a bare minimum of space. 32 mm/1.26 inch Through function is convenient for debugging If connectionsare made as shown inthe diagram, a convenient“through” functionmakes it possible to transfer data from the GT10 and carry out PLC debugging at the same time that communication is going on between the GT10 and the FP series PLC. This significantly boosts efficiency in the workplace. PLC GT10 Cable connected to COM or TOOL port of PLC Screen transfer cable AFC8503 PLC debugging Screen data being sent and received Screen creation tool GTWIN FP series programming tool FPWIN GR Personal computer The FPWIN GR and NPST-GR can be booted on the computer being used to edit GT10 screens, and PLC programs edited and monitored through the GT10. Maintenance is easier than ever before LEDs are used for backlighting, eliminating the fuss and bother of replacement. Screen data is saved to an F-ROM, while other data is backed up by an internal secondary battery, so nobattery replacement isneeded. Thisassures long-term, stable usewithout worrying about lost data.

have read this manual and the installation instructions, and make sure the product is used correctly. This manual uses two safety standard levels: “WARNING” and “CAUTION”. WARNING Erroneous handling of an item marked with this label can cause fatal or critical injury to the user. • If this product is used in applications where accidents involving bodily injury and/or significant damage may be conceivable, measures should be taken to ensure adequate safety, such as the use of duplicate safety mechanisms. • The functions of the GT10 should not be used to design systems which may pose a threat to human life or which may cause severe injury or damage. Designs should include safety mechanisms for use in the event that switch functions malfunction. • Do not use this product in an environment where combustible gases are present. (This can cause explosion.) • This product contains a secondary battery (lithium and vanadium). Do not dispose of it by incineration. (This can cause it to explode.) CAUTION Erroneous handling of an item marked with this label can cause injury to the user, or physical damage to property. • This product should not be used outside of the stated specifications ranges for ratings, service life, configuration factors and other elements. (This can cause abnormal generation of heat and smoke.) • The operational force of the touch panel should be kept to 0.98 N or lower. Operating the touch panel at a higher force could cause damage. • Never touch terminals while the power supply is on. (This can cause electric shock.) • Never disassemble or alter this product. (This can cause electric shock and smoke generation.)

(1) In order to prevent, as much as possible, unexpected situations not covered by these specifications, please consult us regarding your product’s specifications and demands, as well as this unit’s operating conditions and installation details. (2) To avoid the unlikely event of a situation attributed to inferior quality of the unit which has serious adverse affects on persons or property, the numeric values for guaranteed characteristics and performance noted in this specifications manual should be considered the minimum necessary values. As the manufacturer of this unit, we recommend incorporating additional safety measures such as duplicate circuits wherever possible. (3) The quality of this product is guaranteed for one year after purchase, and this guarantee is limited to the range of items stated in these specifications. In the case of a defect in the product which is clearly Matsushita’s responsibility, we will offer a replacement unit or replacement of the defective part(s) of the unit and we will repair the unit promptly at the place of purchase. The following are not included in the warranty: 1. Other damage resulting from damage to or defects in the supplied product. 2. Problems caused by conditions other than those noted in these specifications involving use, storage, or shipment (transport) after product delivery. 3. Developments which were unforeseeable given the technology in practical use prior to product delivery. 4. Earthquake, flood, fire, war, and damage due to other naturally occurring events or human disasters for which Matsushita bears no responsibility.

well as a table of functions, wiring diagrams, and dimensions. 1.1 GT10 Specifications 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1.1 General Specifications 3 . . . . . . . . . . . . . . . . . . . . . . 1.1.2 Display 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1.3 Functions 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1.4 Touch Key 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1.5 Memory (1) 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1.6 Memory (2) 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1.7 Interface 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2 Names and Functions of Parts 6 . . . . . . . . . . . . . . . . . . . . . . . 1.2.1 GT10 (front) 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2.2 GT10 (rear) 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2.3 Names and Functions of Parts 7 . . . . . . . . . . . . . . . 1.3 Internal Wiring Connections for Ports 9 . . . . . . . . . . . . . . . . . 1.3.1 COM. Port 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3.2 TOOL Port 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3.3 Power Supply Terminals 10 . . . . . . . . . . . . . . . . . . . . 1.4 Dimensional Outline Diagram 11 . . . . . . . . . . . . . . . . . . . . . . . 1.4.1 GT10 Dimensional Outline Diagram 11 . . . . . . . . . . 1.4.2 Panel Cutout Dimensional Outline Diagram 12 . . .

21.6 to 26.4V DC Power consumption 5 W max. Ambient temperature 0°C to 40°C/32°F to 104°F (25V DC max. if installed horizontally) Ambient humidity 20% RH to 85% RH (non condensing) Storage temperature -20°C to 60°C/-4°F to 140°F Storage humidity 10% RH to 85% RH (non condensing) Vibration resistance 10Hz to 55 Hz (1-minute cycle) Amplitude: 0.75 mm, 10 min on 3axes Shock resistance 98 m/s2 min., 4 times on 3axes Noise immunity 1,000 V [p-p] min., pulse width 50 ns, 1 μs between power supply terminals (based on noise simulator) Static noise resistance 5,000 V min. (panel display) Protective construction IP65 (in initial status) Dustproof and drip-proof from front panel only (packing used on panel contact sur- face) * When reattaching, replace waterproof packing. Mass Approx. 260 g/9.171 oz 1.1.2 Display Item Specifications Display STN monochrome LCD Resolution 160 (W) x 64 (H) dots Displayable area 92.8 (W) x 37.1 (H) mm 3.65(W) inch x 1.46 (H) inch LCD life Average: 50,000 hours (at normal temperature of 25°C) Backlight 3-color LED backlight (green, red, orange) * No replacement necessary

Half width and full width characters can be displayed at same width, doubled width, or quadrupled width (Widths of 2 x 2 times or more can be displayed in high-quality font display.) Character types Alphanumeric characters Graphics Straight lines, continuous straight lines, squares, circles, ovals, arcs, elliptic arcs, fan shapes, elliptic fan shapes, beveled squares, bitmaps Number of screens Approx. 160 screens Screen numbers that can be set: Base screens No. 00 to FF (HEX) (Number of screens that can be registered varies depending on registered contents.) Part functions Messages, lamps, switches, data, bar graphs, clocks, keyboard Clock functions Clock built into main unit (can also be displayed with reference to PLC clock) Contrast adjustment Contrast can be adjusted using touch panel operation (10 stages) Automatic communication settings Settings for communication between dedicated software and PLC set automatically by connecting cable Debugging functions Through function (PLC can be debugged from personal computer by connecting computer to TOOL port and PLC to COM. port) Screen creation Dedicated software Terminal GTWIN used. Applicable OS: Windows 95/98/2000/NT (Ver. 4.0 or later ) 1.1.4 Touch Key Item Specifications Touch key resolution 20 (W) x 8 (H) Touch key operation 0.98 N max. Touch key life Min. 106 1.1.5 Memory (1) Screen data and GTWIN Configuration Settings data Item Specifications Memory type F-ROM Memory capacity 384 kbytes 1.1.6 Memory (2) Clock data and PLC device storage data (24 words max.) Item Specifications Memory SRAM Memory backup Backed up by internal secondary battery (charged when power is on) (Note) When using, set operation mode switch on back of main unit to “ON” position.

COM. Port Conditions for communications with external devices Baud rate: 9600, 19200, 38400, 57600, 76800, 115200 bits/s Data bits: 7 or 8 bits Parity: None, Odd, Even Stop bits: 1 bit Protocol FP series supported/general-purpose RS232C supported Connector Connector terminal base (5-pin) Communications ratings Conforms to RS232C TOOL port Conditions for communications with external devices Baud rate: 9600, 19200, 115200 bits/s Data bits: 8 bits Parity: None, Odd, Even Stop bits: 1 bit Protocol Dedicated protocol Connector Mini-DIN (5-pin)

1.2 Names and Functions of Parts 1.2.1 GT10 (front) ● Liquid crystal display panel (touch panel) 1 ●Front panel protective sheet (one sheet is attached to unit when unit is shipped) 2 1.2.2 GT10 (rear) ● ● ● ● Power supply terminal COM. port (PLC/external device connection port) (1 communication connector provided as accessory when unit is shipped) Waterproof packing (1 piece is attached to unit when unit is shipped) TOOL port (connection port for GTWIN screen creation tool) 7 5 4 3 ●6 Operation mode setting switches

1.2.3 Names and Functions of Parts (1) Liquid crystal display panel / touch panel Various screens are displayed here. A touch panel is provided on the liquid crystal display panel, and switches can be operated and data entered simply by touching the panel. (2) Front panel protective sheet This protects the touch panel and keeps it clean. One sheet is attached to the panelwhen the unit is shipped. (3) Power supply terminal The operation power supply is connected here. (4) COM. port (PLC/external device connection port) A device such as a PLC, a higher-order computer, or a microcomputer board can be connected to this RS232C port. (One communication connector is provided as an accessory when the unit is shipped.) (5) TOOL port (GTWIN connection port) This port is used to connect a personal computer in which the screen creation tool GTWIN has been installed, using a dedicated cable (AFC8503). (6) Operation mode setting switches With the GT10, screen data and configuration settings data are stored in an internal F-ROM, so no battery backup is needed. However, data such as clock data and the Hold PLC Device Data is stored in the internal SRAM, and is backed up by the internal secondary battery, which is charged when the power supply is turned on. The operation mode setting switches control the ON/OFF settings for the secondary battery backup function, the ability to shift to the system menu, and other functions. Switch no. Function OFF ON 1 SRAM backup using secondary battery No Yes 2 Inhibits system menu shift Shift possible Shift inhibited 3 Usage inhibited Should always be in the OFF position when unit is used 4 when unit is used (7) Waterproof packing This assures that the front panel is waterproof. One piece is provided as an accessory when the unit is shipped. ON OFF 4 3 MODE 1 2 Operation mode setting switches (settings when shipped) all-guides.co m

CAUTION SRAM backup by the secondary battery When the unit is shipped, the No. 1 operation mode setting switch is set to the “OFF” psosition, in order to prevent excessive discharging of the secondary battery. Before using the unit, turn on the No. 1 operation mode setting switch on the back of the main unit, to turn on the SRAM backup function of the secondary battery. For detailed information on the secondary battery, please see page 93, “What the Internal Secondary Battery Does”.

1.3 Internal Wiring Connections for Ports 1.3.1 COM. Port When connecting the unit to the FP series, there is no need to wire both the RS and CS. Wiring and cables should be laid out in such a way that cables are not affected by external noise. Also, shielded wiring should be used for cables. SD RD RS CS GND 1.3.2 TOOL Port Pin No. Contents 1 SG 2 SD 3 RD 4 N.C. 5 (+5 V) The +5 V of Pin 5 is reserved for the FP Programmer II. It should not be used for any other application. 1 2 4 5 3

1.3.3 Power Supply Terminals Maker Shape Model Applicable wiring Tightening torque Round 1.25-MS3 0.25 mm2 to 1.65 mm2 0.5 N⋅m JST Mfg. Front-opening 1.25-B3A JST Mfg. Co., Ltd. Round 2-MS3 1.04 mm2 to 2.63 mm2 Front-opening 2-N3A Applicable crimp terminals - The terminal screws are M3 screws. We recommend using crimp terminals for wiring to terminals. Open-tip terminals Round terminals The tightening torque for terminal base screws should be between 0.5 and 0.6 N·m, or less. Operating at a higher force could cause damage. If crimp terminals are not being used, wire with a diameter of 0.5 mm2 to 1.25 mm2 should be used for power cables. In keeping with the European EMC Directive (EMC Direc- tive 89/336/EEC), the GT10 conforms to European Stan- dards (EN50081-2:1993, EN50082-2:1995). As a condi- tion of compatible, a ferrite core should be installed when wiring to the terminal base (Seiwa Electric Mfg. Co., Ltd. E04RC281613 or equivalent). Ferrite core +24 V 0 V F.E. 6.0 mm max. 6.0 mm max.

1.4 Dimensional Outline Diagram 1.4.1 GT10 Dimensional Outline Diagram 144/5.67 32/1.26 138.0/5.43 80/3.15 4/0.16 97/3.82 60/2.36 40/1.57 72/2.83 65.8/2.59 9.6/0.38 (7/0.28) 8.5/0.33 2/0.08 (Unit: mm/inch) (Display unit) (Display unit) (Packing) (7/0.28)

1.4.2 Panel Cutout Dimensional Outline Diagram The panel cutout dimensions of the GT10 are as shown below. /5.47 /2.64 + 0 0 Applicable panel thickness: 1.0 to 6.0/0.002 to 0.236 (Unit: mm/inch) 1 1 + 139 + 0 0.04 67 0 0.04 + all-guides.co m

This chapter explains how the GT10 should be installed and how wiring should be connected. 2.1 Installation 15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.1.1 Installation Environment 15 . . . . . . . . . . . . . . . . . . . . 2.1.2 Installation Method 17 . . . . . . . . . . . . . . . . . . . . . . . . 2.2 Wiring the Power Supply 19 . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2.1 Wiring the Power Supply 19 . . . . . . . . . . . . . . . . . . . 2.3 Wiring the COM. Port 21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3.1 Wiring the COM. Port 21 . . . . . . . . . . . . . . . . . . . . . . 2.3.2 Wiring Method 22 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3.3 Precautions Concerning Wiring 22 . . . . . . . . . . . . . .

GT10 15 2.1 Installation 2.1 Installation 2.1.1 Installation Environment When installing and using the GT10, always make sure the following conditions are observed. Usage Conditions When installing the product, make sure it is used within the range of the general specifications. Do not use in the following environments: - Areas where the unit may come in contact with water (the unit is warranted by IP65 for the installed panel, but this applies to initial values and operation cannot be guaranteed in areas where the unit is constantly subjected to water or to extreme temperatures or humidity). - Areas where the ambient temperature exceeds the range 0°C to 40°C/32°F to 104°F. - Areas where the ambient humidity exceeds 20% RH to 85% RH. - If the control panel and other parts are installed in an environment where the air tends to be poorly ventilated, forced cooling should be used to keep the ambient temperature of the from going over 40°C/104°F. This prevents the temperature of the GT10 display unit from rising. - Locations where condensation may form because of sudden fluctuations in temperature. - Locations where flammable or corrosive gases are present. - Locations where there are high concentrations of dust or iron filings. - Locations where substances such as organic solvents (thinner, benzene, etc.) or strong alkali substances (ammonia, caustic soda, etc.) might adhere to the product. - Locations where the product is subject to extreme vibration and/or impact. - Avoid installing the product near high-voltage lines, high-voltage devices, power lines, power devices, amateur radio sets and other transmitters, and devices that generate strong current surges. - Avoid locations where the display unit is subject to direct sunlight. Safety Precautions - The switch functions of the programmable display unit should not be used to design systems which may pose a threat to human life or which may cause severe injury or damage. Designs should include safety mechanisms for use in the event that switch functions do not function correctly.

16 2.1 Installation Power Supply Wiring - For the power supply, use twisted wire (strand wire). - There is sufficient noise resistance to offset power line noise, but we recommend reducing noise by measures such as installing an insulated transformer. - Separate wiring systems should be used for the power supply unit and the operating unit. Static Electricity/Noise - Keep the GT10 main unit, PLC connecting cable, and other wiring as far away as possible from machines which are likely to produce noise (welding equipment, power lines, inverters, motors, etc.). - For use in environments where the frequent occurrence of static electricity, radiation, or induced noise can be expected, the use of shielded cable on all wiring and grounding of shield (1-point ground) is recommended. When wiring the equipment, shielded wires should be electrically insulated to signal lines and signal grounds. - If excessive static electricity is applied to the panel surface, the LCD display unit may be damaged. Secondary Battery Service Life - The service life of the internal secondary battery is just under 2 years when used in ambient operating temperatures of more than 40°C/104°F or when the operating voltage exceeds 25V DC. Use caution when using the clock and device hold area functions. Other Precautions - Do not leave the GT10 connected to the TOOL port of the FP Programmer II. - Always operate the touch panel with your fingers. Excessive load (about 98 N/cm2 ) or impact (operating with tools, etc.) will cause damage. Touch panel operation must be within the standard operating power range. Uniform pressure should be used to avoid abnormal wear of electrodes which may disable operation. Operate the unit only by touch. - Never dismantle, re-assemble, or alter the unit. Performance cannot be warranted if this precaution is disregarded.

GT10 17 2.1 Installation 2.1.2 Installation Method Secure the GT10 to the installation panel using the four fittings and four screws provided with the unit. (1) Place the GT10 main unit in the installation panel. (2) Insert the fittings into the grooves provided in the GT10 main unit, and tighten the screws to secure the GT10 main unit to the installation panel. Enlarged view Four fittings and four screws provided with the unit CAUTION • Screw tightening torque The screw tightening torque should be 10 N⋅cm to 25 N⋅cm. • Applicable panel thickness A panel with a thickness of 1.0 mm to 6.0 mm should be used. • Installation angle If the installation angle is between 60 degrees and 0 degrees (horizontal), the operating voltage should be set to 25V DC or lower. Installation angle next page all-guides.co m

18 2.1 Installation • Clearance when the GT10 is installed When installing the GT10, if other parts are being installed to the panel or cables are being wired to it, we recommend providing a clearance of 30 mm to 50 mm/1.18 inch to 1.97 inch around the GT10. This prevents cables from being damaged, and facilitates the installation work. Also, make sure that the slits in the main unit are never obstructed.

GT10 19 2.2 Wiring the Power Supply 2.2 Wiring the Power Supply 2.2.1 Wiring the Power Supply The power supply should be wired by securely connecting the terminal on the rear of the main unit to the terminal shown below. Always use crimp terminals for wiring. +24 V 0 V (D-type ground) F. E. Use twisted wiring for the power supply In order to minimize influence from noise, the wiring for the power supply should be twisted. Insulate the power supply inside a protective circuit - In order to protect the unit against abnormal voltage from the power supply line, the power supply should be an insulated type, and should be enclosed within a protective circuit. - A non-insulated regulator is used with the GT10. - If a power supply device without an internal protective circuit is being used, power should always be supplied to the GT10 through a fuse or a similar protective device. Keep the power supply voltage within the operating voltage range Operating voltage range 21.6 to 26.4V DC Use M3 crimp terminals - The terminal screws are M3 screws. We recommend using crimp terminals for wiring to terminals. Maker Shape Model Applicable wiring Tightening torque Round 1.25-MS3 0.25 mm2 to 1 65 mm2 0.5 N·m JST Mfg. Front-opening 1.25-B3A 1.65 mm2 JST Mfg. Co., Ltd. Round 2-MS3 1.04 mm2 to 2 63 mm2 Front-opening 2-N3A 2.63 mm2 6.0 mm max. 6.0 mm max. The tightening torque for terminal base screws should be between 0.5 and 0.6 N·m, or less. Operating at a higher force could cause damage. If crimp terminals are not being used, wire with a diameter of 0.5 mm2 to 1.25 mm2 should be used for power cables. For precautions concerning con- formance to European EMC di- rectives, please see “Power Supply Terminals” on page 10. Open-tip terminals Round terminals

20 2.2 Wiring the Power Supply Keep the power supply wiring separate - Wiring to the GT10, PLC, and other power equipment should have separate wiring systems. PLC GT10 Breaker Power equipment Insulated DC power supply

GT10 21 2.3 Wiring the COM. Port 2.3 Wiring the COM. Port 2.3.1 Wiring the COM. Port Accessory communication connector/applicable wiring The communication connector used for the COM. port (provided as an accessory with the main unit) has a screw-tightening type of terminal base. The wiring shown below should be used. Accessory communication connector The communication connector is made by Fenics Contact Co., Ltd. No of pins Fenics Model No. No. of pins Model No. Product No. 5-pin MC1, 5/5-ST-3,5 1840396 Applicable wiring (twisted wiring) Size Conductor Cross-Section Surface Area AGW#28 to 16 0.08 mm2 to 1.25 mm2 Applicable stick-type terminals with insulated sleeves If stick-type terminals are used, the models listed below are marketed by Fenics Contact Co., Ltd. Maker Cross-Section Surface Size Fenics Co. Model 0.25 mm2 AGW#24 AI 0,25 to 6 YE Fenics Contact 0.50 mm2 AGW#20 AI 0,50 to 6 WH Fenics Contact Co., Ltd. 0.75 mm2 AGW#18 AI 0,75 to 6 GY 1.00 mm2 AGW#18 AI 1 to 6 RD Crimp tools for stick-type terminals Maker Fenics Model No. Maker Model No. Product No. Fenics Contact Co., Ltd. CRIMPFOX UD6 1204436

22 2.3 Wiring the COM. Port Use a special tool to tighten the terminal base of the communication connector Tightening of terminals should be done using a screwdriver made by Fenics Contact Co., Ltd. (Fenics mfg. no. 1205037, blade width 0.4 x 2.5, model no. SZS 0.4 x 2.5), or a screwdriver made by Matsushita Electric Works Co., Ltd. (Product number AFP0806). The tightening torque should be 0.22 N·m to 0.25 N·m or less. 2.3.2 Wiring Method (1) Remove the sheath from the wire. 7 mm/0.28 inch (2) Insert the wire all the way into the terminal base, and tighten the screw in the clockwise direction to secure it. 2.3.3 Precautions Concerning Wiring The following precautions should be observed, to avoid broken or disconnected wires. - When removing the sheath, be careful not to scratch the core wire. - Wire the terminal without twisting the core wire. - The core wire should be connected without soldering it. Vibration can sometimes cause soldered connections to break loose. - After connecting the wiring, avoid subjecting the cable to stress. - Because of the construction of the terminal, tightening the wire in the counterclockwise direction will cause a faulty connection. If this happens, disconnect the wire, check the terminal hole, and connect the wire again. Counterclockwise Clockwise all-guides.co m

GT10 23 2.3 Wiring the COM. Port REFERENCE For information on connecting the COM. port of the GT10 with various PLC units, please see Chapter 4, “Connecting and Communicating With the PLC”, on page 35.

first time. 3.1 Setup Procedure for the GT10 27 . . . . . . . . . . . . . . . . . . . . . . 3.1.1 Setup Procedure 27 . . . . . . . . . . . . . . . . . . . . . . . . . . 3.2 Entering Settings for the Basic Communication Area to PLC 30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.2.1 What is the Basic Communication Area? 30 . . . . . 3.2.2 Basic Communication Area Map 32 . . . . . . . . . . . . .

3.1 Setup Procedure for the GT10 3.1.1 Setup Procedure The GT10 should be set up using the procedure outlined below. (1) Setting the “Configuration File” with GTWIN The GT10 has an internal file called the “Configuration file”, which is used to determine various operating environment parameters. When the GT10 is shipped from the factory, the settings listed below are set for the parameters in the configuration settings file. If changes are made to these settings, they are made from GTWIN screen creation tool. (For detailed information on changing settings, see page 58 and subsequent pages.) If the GT10 is being used without changing the factory settings, the following setup procedure is not necessary. Contents of configuration settings when shipped from the factory Classification Item Setting contents Basic Setup Area for basic communication with PLC Mode : GT10 mode Word area: DT0 to DT2 Bit area : WR0 to WR2 Communication parameter COM. port Communication speed: 19200 bits/s, data length: 8 bits, stop bit: 1 bit, parity: odd Retries: 3, error code displayed (not held) parameter settings TOOL port Communication speed: 19200 bits/s, data length: 8 bits, stop bit: 1 bit, parity: odd None Auto paging Automatic paging No Startup screen Startup screen No. 00 Startup screen settings Rise delay time 0 seconds Clock GT main unit clock / external transmission: No Other settings Backlight control Not turned off automatically Other settings Touch operation sounds Valid Hold PLC Device Holds a PLC device Not held Always confirm “Basic communication area to PLC” under “Basic Setup” This is an internal device area that comes already provided in the GT10 for the purpose of communicating with a PLC. If the factory settings are to be changed, the setup procedure must be carried out. For detailed information, please see page 30. (2) Connect the GT10 and the personal computer. After the settings have been entered with GTWIN, connect the computer and the GT10, using the screen transfer cable. GTWIN GT10 Screen transfer cable (AFC8503) all-guides.co m

(3) Transfer the GT10 Configuration file from GTWIN. After connections have been completed, use the following procedure to transfer the GT10 Configuration file from GTWIN. Boot GTWIN, and select “Transfer” on the “File” menu. When the transfer function is selected, a dialog box for file transfer is displayed. At this point, specify the type of data to be transferred, and the direction of transfer. Transfer data: “GT10 Configuration” Transfer direction: “GTWIN →GT main unit” Enter the above conditions and click on the “OK” button. The system files are transferred to the GT10.

When the menu operation as shown at the left page is carried out, the configuration file is sent to the GT10. During the transfer, a screen like that shown below is displayed. GTWIN GT10 Transferring PC→GT GT10 Configuration file being transferred Screen transfer cable (AFC8503) (4) Setup is completed. If the transfer has been completed without any problems, the setup is completed. CAUTION Backup of the GT10 Configuration file The GT10 Configuration file is stored in the user memory (F-ROM) of the GT10. This file is deleted if the memory is initialized using the command on the system menu of the GT10 main unit (see page 78), and will have to be transferred again.

3.2 Entering Settings for the Basic Communication Area to PLC 3.2.1 What is the Basic Communication Area? Communication between the GT10 and PLC is carried out as shown below. GT10 PLC Internal PLC devices Part reference / output device For part functions (free device specification) Basic communication area For screen switching settings and system control (word device / bit device: 3 words each) Ongoing Communication As shown in the illustration, communication is carried out on an ongoing basis between the GT10 and internal devices in the PLC. Internal PLC devices are divided into the following two devices: Basic communication area This area is for system control, such as screen switching settings. PLC devices belong to this area on a fixed basis, and communication is constantly being carried out. Breakdown of the basic communication area Word devices (DT, FL, etc.) 3 consecutive words Bit devices (WR, etc.) 3 consecutive words - Word devices - - - For reading devices handled in word units (3 consecutive words) - Bit devices - - - For reading devices handled in bit units (3 consecutive words) References and output devices for parts These are devices that are used in parts functions, and can be freely specified by the user. Communication is carried out on an ongoing basis only for those that are currently displayed on the screen and pertain to devices currently in use. With the GT10, before GTWIN screen creation tool is used to specify the devices for parts functions, the “basic communication area” must be determined. DT0 to DT2 and WR0 to WR2 are set as the default values for the basic communication area, but the initial address can be changed using the following procedure. CAUTION The basic communication area should not be used in PLC ladder programs.

Settings in GTWIN Select “Configuration” under “File” on the menu bar, and then select the sub-menu called “GTWIN Configuration”. This displays the dialog box for the GT10 Basic Setup, as shown below. Clicking on the button in “Basic Communication Area to PLC” displays the device settings dialog box shown below, where the initial addresses for the word area and bit area can be changed. GT10 Configuration Basic Setup dialog box Explanation of this function Key operation in the Device Settings dialog box Click on the button to display a pull-down menu, and then select the device for which settings are to be entered. Use the ten-keys to enter the address. The button acts as a backspace key when entering an address, and the button functions as a Clear key.

3.2.2 Basic Communication Area Map In order for communication to be carried out between the GT10 and PLC, an internal device area like that shown below is provided in the PLC. This field should not be used in the ladder programs of PLCs in actual operation. The starting address “N” of the field shown below is specified in the GT10 configuration settings of GTWIN screen creation tool, and is then sent to the GT main unit. Word devices Word position F E D C B A 9 8 7 6 5 4 3 2 1 0 N+0 Screen no. specified by PLC (area read by GT10 from PLC) N+1 Usage prohibited N+2 No. of currently displayed screen (area in which data is written from GT10 to PLC) Explanation of system area Screen no. specified by PLC - - - The screen number displayed on the GT10 is specified from the PLC in hexadecimal format. No. of currently displayed screen - - - The number of the screen currently displayed on the GT10 is written to the PLC in hexadecimal format. Bit devices Word position F E D C B A 9 8 7 6 5 4 3 2 1 0 N+0 BZ Forced- display flag Backlight Valid flag Backlight Flashing Backlight Color N+1 Usage prohibited N+2 BAT Data Input In Progress flag Explanation of system areas BZ - - - This turns on the buzzer. Forced-Display flag - - - At the rise when the bit is turned on, the screen specified by the PLC is forcibly displayed. (This is executed only when at the rise of the bit.) Backlight Valid flag - - - When the bit is turned on, the backlight flashing/backlight color control becomes effective. Backlight Flashing - - - 0: Lighted (normal), 1: Flashing Backlight Color - - - 00: Off, 01: Green, 10: Red, 11: Orange BAT - - - This goes on if clock data and Hold PLC Device data held in the SRAM are not being backed up normally. (This bit also goes on if the SRAM is not backed up by the internal secondary battery.) Data Input In Progress flag - - - This is 1 while data is being input, and 0 when data input has been completed. all-guides.co m

Explanation of this function • “IOP01” mode The GT10 is equipped with an IOP01 mode for users with conventional models (I.O.P. B01C / M01L / D01TL series).Using this function enables compatibility with earlier models, so that communication is possible between the GT10 and PLC, except for one part of the basic communication area. • Entering settings for the IOP01 mode Click on the “File” menu in GTWIN, and then select “Configuration” from the displayed menu. Next, select “GT Configuration” from the sub-menu. Turn on the radio button for “IOP01 Mode” in the displayed dialog box. For information on the displayed dialog box, please see “Basic Setup” under “GT10 Configuration Settings” on page 59.

• Map of the basic communication area for conventional models (conventional name: system area) If the IOP01 mode is set, the basic communication area map for the GT10 is as follows. Reference data area Address Bit configuration Address F E D C B A 9 8 7 6 5 4 3 2 1 0 n BZ PC Screen no. n+1 n+2 T bit fi ld * N t 1 n+3 Tag bit field * Note 1 (Used to turn tag display on/off, display status screen segments, and display settings) • (Used to turn tag display on/off, display status screen segments, and display settings) • T fi ld * N t 1 • Tag field * Note 1 (Used to switch tags, specify movements, and reference and set data) • (Used to switch tags, specify movements, and reference and set data) Output destination relay Address Bit configuration Address F E D C B A 9 8 7 6 5 4 3 2 1 0 n System switch out- put destination Function switch out- put destination Displayed screen data (no. of screen n Not supported * Note 2 Not supported * Note 2 Displayed screen data (no. of screen currently displayed) n+1 BAT SET n+2 n+3 Output destination relay * Note 1 • Output destination relay Note 1 (Used for switch output destinations of tags, segments, and manual switches) • 1. Note 1: The tag bit field and tag field under “Reference data area”, and the output destination relay field under “Output relay” can be switched just as they are, as device setting destinations for GT10 parts functions. 2. Note 2: System switch output destinations and function switch output destinations provided in conventional models as the initial addresses under “Output relay” are not supported with the GT10. System switches should be replaced with keyboard parts, and function switches with switch parts. System field (fixed at 2 words) Field for user use (fixed at 126 words maximum) System field (fixed at 2 words) Field for user use (fixed at 30 words max- imum)

PLC This chapter explains how to connect the GT10 to the FP series PLC, and how to set up communications between the units. 4.1 Connecting the FP0 37 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.1.1 Connecting to the COM. Port 37 . . . . . . . . . . . . . . . 4.1.2 Connecting to the TOOL Port 39 . . . . . . . . . . . . . . . 4.2 Connecting the FP1 40 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2.1 Connecting to the COM. Port 40 . . . . . . . . . . . . . . . 4.3 Connecting the FP2/FP2SH 41 . . . . . . . . . . . . . . . . . . . . . . . . 4.3.1 Connecting to the COM. Port 41 . . . . . . . . . . . . . . . 4.3.2 Connecting to the TOOL Port 42 . . . . . . . . . . . . . . . 4.4 Connecting the FP2/FP2SH Computer Communication Unit 43 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5 Connecting the FP10SH 44 . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5.1 Connecting to the COM. Port 44 . . . . . . . . . . . . . . . 4.5.2 Connecting to the TOOL Port 46 . . . . . . . . . . . . . . . 4.6 Connecting the FP10SH/FP3 Computer Communication Unit 47 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.7 Connecting the FP-M 48 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.7.1 Connecting to the COM. Port 48 . . . . . . . . . . . . . . . 4.7.2 Connecting to the TOOL Port 50 . . . . . . . . . . . . . . . 4.8 Automatic Communication Settings Function 51 . . . . . . . . . . 4.9 Through Function 53 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

GT10 37 4.1 Connecting the FP0 4.1 Connecting the FP0 4.1.1 Connecting to the COM. Port GT10 Loose-wire connection FP0 COM. port FP0 communication format settings System register no. Item Value Set System register value 412 Selection of target use of RS232C port Computer link K1 413 Data length 8 bits K3 Parity check Yes Parity setting Odd Stop bits 1 bit Line return code CR Start code No STX 414 Baud rate setting 19200 bits/s H0 * 00 415 Unit number 1 K1 416 Modem connection No connection H0 Connecting to the FP0 COM. port GT10 FP0 S SD R RD G SG PLC side Pin no. Abbreviation SD SD RD RD RS RS CS CS GND GND GT10 side Pin no. Abbreviation ←To set 19200 bits/s for both the COM. port and the TOOL port, “H0100” should be set. all-guides.co m

38 4.1 Connecting the FP0 CAUTION Because loose wiring is used for connection to the FP0 COM. port, no dedicated cable is available. The cable should be provided by the customer. When purchasing a cable, the following precautions should be observed: • Shielded wire with a size of AGW#28 to 16 (conductor cross-section surface area: 0.08 mm2 to 1.25 mm2) should be used for connections. • For wiring procedures, please refer to “Wiring the COM. Port” on page 21.

GT10 39 4.1 Connecting the FP0 4.1.2 Connecting to the TOOL Port AIGT8192 GT10 FP0 TOOL port FP0 communication format settings System register no. Item Value Set System register value 410 Unit number 1 K1 411 Data length 8 bits H0 Modemconnection No connection 414 Baud rate setting 19200 bits/s H010X X is 0 to 6 PLC communication cable: Mini-DIN 5-pin loose-wire cable (AIGT8192) 3 5 4 1 2 7/0.28 30/1.18 2000/78.74 (Unit: mm/inch) Connector: Made by JST Mfg. Co., Ltd.: MD-P15B (housing A) MD-P16A (housing B) MD-PS8T (shell) MD-SP2240 x 5 (terminal) Mini-DIN plug side signals 1 SG Brown 2 SD Red 3 RD Orange 4 - - - - 5 - - - - Pin no. Abbreviation Wire color Specifications L Product No. 2 m/6.56 ft Mini-DIN 5-pin Single-side loose wire AIGT8192 Connecting to the FP0 TOOL port GT10 3 5 4 1 2 No. 1 (brown) Pin no. on PLC side No. 3 (orange) No. 2 (red) PLC side Pin no. Abbreviation 1 SG 2 SD 3 RD 4 - - 5 - Abbreviation GT10 side Pin no. SD SD RD RD RS RS CS CS GND GND ←To set 19200 bits/s for both the COM. port and the TOOL port, “H0100” should be set.

40 4.2 Connecting the FP1 4.2 Connecting the FP1 4.2.1 Connecting to the COM. Port AIP81842 GT10 FP1 COM. port FP1 communication format settings System register no. Item Value Set System register value 412 Selection of target use of RS232C port Computer link K1 413 Data length 8 bits K3 Parity check Yes Parity setting Odd Stop bits 1 bit Line return code CR Start code No STX 414 Baud rate setting 19200 bits/s K0 415 Unit number 1 K1 416 Modem connection No connection H0 PLC communication cable: D-sub 9-pin loose-wire cable (AIP81842) 1 2 3 4 5 6 7 8 9 L 50/1.97 (Unit: mm/inch) Made by JAE: DE-C8-J9-F1-1 Made by JAE: DE-9PF-N 10/0.39 (shielded mesh wire section) Signals on D-sub side Pin no. Wire color Dot mark 1 Brown Black dot 2 Brown Red dot 3 Yellow Black dot 4 Yellow Red dot 5 Green Black dot 6 - - - - 7 Green Red dot 8 - - - - 9 - - - - Specifications L Order no. D-sub 9-pin Single-side loose wiring AIP81841 AIP81842 1 m/3.28 ft 2 m/6.56 ft Connecting to the FP1 COM. port 1 FG SD RS SG CS RD 2 3 4 5 6 N.C. 7 8 9 N.C. ER SD SD RD CS GND RS RD RS CS GND 1 2 3 4 5 6 7 8 9 GT10 Pin no. on PLC side No. 3 (yellow: black dot mark) No. 2 (brown: red dot mark) No. 7 (green: red dot mark) No. 4 (yellow: red dot mark) Short wiring here No. 5 (green: black dot mark) PLC side GT10 side Pin no. Pin no. Abbreviation Abbreviation

GT10 41 4.3 Connecting the FP2/FP2SH 4.3 Connecting the FP2/FP2SH 4.3.1 Connecting to the COM. Port AIP81842 GT10 FP2/FP2SH CPU COM. port FP2/FP2SH communication format settings System register no. Item Value Set 412 Selection of target use of RS232C port Computer link 413 Data length 8 bits Parity check Yes Parity setting Odd Stop bits 1 bit Line return code CR Start code No STX 414 Baud rate setting 19200 bits/s 415 Unit number 1 416 Modem connection No connection PLC communication cable: D-sub 9-pin loose-wire cable (AIP81842) 1 2 3 4 5 6 7 8 9 L 50/1.97 (Unit: mm/inch) Made by JAE: DE-C8-J9-F1-1 Made by JAE: DE-9PF-N 10/0.39 (shielded mesh wire section) Signals on D-sub side Pin no. Wire color Dot mark 1 Brown Black dot 2 Brown Red dot 3 Yellow Black dot 4 Yellow Red dot 5 Green Black dot 6 - - - - 7 Green Red dot 8 - - - - 9 - - - - Specifications L Order no. D-sub 9-pin Single-side loose wiring AIP81841 AIP81842 1 m/3.28 ft 2 m/6.56 ft Connecting to the FP2/FP2SH COM. port 1 FG SD RS SG CS RD 2 3 4 5 6 N.C. 7 8 9 N.C. ER SD SD RD CS GND RS RD RS CS GND 1 2 3 4 5 6 7 8 9 GT10 Pin no. on PLC side No. 3 (yellow: black dot mark) No. 2 (brown: red dot mark) No. 7 (green: red dot mark) No. 4 (yellow: red dot mark) Short wiring here No. 5 (green: black dot mark) PLC side GT10 side Pin no. Pin no. Abbreviation Abbreviation

42 4.3 Connecting the FP2/FP2SH 4.3.2 Connecting to the TOOL Port AIGT8192 GT10 FP2/FP2SH CPU TOOL port FP2/FP2SH communication format settings System register no. Item Value Set 410 Unit number 1 411 Data length 8 bits 411 Modem connection No connection 414 Baud rate setting 19200 bits/s PLC communication cable: Mini-DIN 5-pin loose-wire cable (AIGT8192) 3 5 4 1 2 7/0.28 30/1.18 2000/78.74 (Unit: mm/inch) Connector: Made by JST Mfg. Co., Ltd.: MD-P15B (housing A) MD-P16A (housing B) MD-PS8T (shell) MD-SP2240 x 5 (terminal) Mini-DIN plug side signals 1 SG Brown 2 SD Red 3 RD Orange 4 - - - - 5 - - - - Pin no. Abbreviation Wire color Specifications L Product No. 2 m/6.56 ft Mini-DIN 5-pin Single-side loose wire AIGT8192 Connecting to the FP2/FP2SH TOOL port GT10 3 5 4 1 2 No. 1 (brown) Pin no. on PLC side No. 3 (orange) No. 2 (red) 1 SG 2 SD 3 RD 4 - - 5 - - PLC side Pin no. Abbreviation SD SD RD RD RS RS CS CS GND GND GT10 side Pin no. Abbreviation all-guides.co m

GT10 43 4.4 Connecting the FP2/FP2SH Computer Communication Unit 4.4 Connecting the FP2/FP2SH Computer Communication Unit AIP81842 GT10 FP2 computer communication unit DIP switch settings on reverse side of FP2 computer communication unit SW No. Setting contents Value Set Switch status 1 Reserved for system ON 2 COM.1 transfer speed 19200 bits/s ON 3 p OFF 4 COM.1 data length 8 bits ON 5 Reserved for system ON 6 COM.2 transfer speed 19200 bits/s ON 7 p OFF 8 COM.2 data length 8 bits ON With the FP2 CCU, the parity check is fixed at “Odd”, and the number of stop bits is fixed at “1 bit”. PLC communication cable: D-sub 9-pin loose-wire cable (AIP81842) 1 2 3 4 5 6 7 8 9 L 50/1.97 (Unit: mm/inch) Made by JAE: DE-C8-J9-F1-1 Made by JAE: DE-9PF-N 10/0.39 (shielded mesh wire section) Signals on D-sub side Pin no. Wire color Dot mark 1 Brown Black dot 2 Brown Red dot 3 Yellow Black dot 4 Yellow Red dot 5 Green Black dot 6 - - - - 7 Green Red dot 8 - - - - 9 - - - - Specifications L Order no. D-sub 9-pin Single-side loose wiring AIP81841 AIP81842 1 m/3.28 ft 2 m/6.56 ft Connecting to the FP2 computer communication unit (CCU) 1 FG SD RS SG CS RD 2 3 4 5 6 N.C. 7 8 9 N.C. ER SD SD RD CS GND RS RD RS CS GND 1 2 3 4 5 6 7 8 9 GT10 Pin no. on PLC side No. 3 (yellow: black dot mark) No. 2 (brown: red dot mark) No. 7 (green: red dot mark) No. 4 (yellow: red dot mark) Short wiring here No. 5 (green: black dot mark) PLC side GT10 side Pin no. Pin no. Abbreviation Abbreviation If both serial ports of the FP2 computer commu- nication unit are being used, each port should be set individually as shown at the left.

44 4.5 Connecting the FP10SH 4.5 Connecting the FP10SH 4.5.1 Connecting to the COM. Port 0 1 DIP SW 1 DIP SW 2 1 AIP81842 J GT10 FP10SH communication format settings SW no. 2 3 4 5 6 7 8 Setting port COM. setting port Setting contents Modem control Start code End code Stop bit length Parity check Data length Value Set No STX invalid CR code 1 bit Odd parity 8 bits Switch status OFF OFF OFF ON ON ON ON ON DIP SW 1 SW no. 1 2 3 4 5 6 7 8 Setting port TOOL port Memory COM. setting port Setting contents Transfer speed Data length Modem control Program memory protect Program memory select Transfer speed Value Set Not related to GT10 communication 19200 bits/s Switch status Not related to GT10 communication ON ON OFF DIP SW 2 FP10SH CPU COM. port Not related to GT10 communication Unit number setting PLC communication cable: D-sub 9-pin loose-wire cable (AIP81842) 1 2 3 4 5 6 7 8 9 L 50/1.97 (Unit: mm/inch) Made by JAE: DE-C8-J9-F1-1 Made by JAE: DE-9PF-N 10/0.39 (shielded mesh wire section) Signals on D-sub side Pin no. Wire color Dot mark 1 Brown Black dot 2 Brown Red dot 3 Yellow Black dot 4 Yellow Red dot 5 Green Black dot 6 - - - - 7 Green Red dot 8 - - - - 9 - - - - Specifications L Order no. D-sub 9-pin Single-side loose wiring AIP81841 AIP81842 1 m/3.28 ft 2 m/6.56 ft

GT10 45 4.5 Connecting the FP10SH Connecting to the FP10SH COM. port 1 FG SD RS SG CS RD 2 3 4 5 6 N.C. 7 8 9 N.C. ER SD SD RD CS GND RS RD RS CS GND 1 2 3 4 5 6 7 8 9 GT10 Pin no. on PLC side No. 3 (yellow: black dot mark) No. 2 (brown: red dot mark) No. 7 (green: red dot mark) No. 4 (yellow: red dot mark) Short wiring here No. 5 (green: black dot mark) PLC side GT10 side Pin no. Pin no. Abbreviation Abbreviation

46 4.5 Connecting the FP10SH 4.5.2 Connecting to the TOOL Port AIP81842 J GT10 SW no. 1 2 3 4 5 6 7 8 Setting port TOOL port Memory COM. setting port Setting contents Transfer speed Data length Modem control Program memory protect Program memory select Transfer speed Value Set 19200 bits/s 8 bits No Not related to GT10 communication Switch status OFF ON OFF DIP SW 2 FP10SH CPU TOOL port FP10SH communication format settings DIP SW 1: Not related to GT10 communication Unit number setting Not related to GT10 communication 0 1 PLC communication cable: D-sub 9-pin loose-wire cable (AIP81842) 1 2 3 4 5 6 7 8 9 L 50/1.97 (Unit: mm/inch) Made by JAE: DE-C8-J9-F1-1 Made by JAE: DE-9PF-N 10/0.39 (shielded mesh wire section) Signals on D-sub side Pin no. Wire color Dot mark 1 Brown Black dot 2 Brown Red dot 3 Yellow Black dot 4 Yellow Red dot 5 Green Black dot 6 - - - - 7 Green Red dot 8 - - - - 9 - - - - Specifications L Order no. D-sub 9-pin Single-side loose wiring AIP81841 AIP81842 1 m/3.28 ft 2 m/6.56 ft Connecting to the FP10SH TOOL port 1 FG SD RS SG CS RD 2 3 4 5 6 N.C. 7 8 9 N.C. ER SD SD RD CS GND RS RD RS CS GND 1 2 3 4 5 6 7 8 9 GT10 Pin no. on PLC side No. 3 (yellow: black dot mark) No. 2 (brown: red dot mark) No. 7 (green: red dot mark) No. 4 (yellow: red dot mark) Short wiring here No. 5 (green: black dot mark) PLC side GT10 side Pin no. Pin no. Abbreviation Abbreviation

GT10 47 4.6 Connecting the FP10SH/FP3 Computer Communication Unit 4.6 Connecting the FP10SH/FP3 Computer Communication Unit AIP81842 GT10 FP3 computer communication unit DIP switch settings on reverse side of FP3 computer communication unit SW No. Setting contents Value Set Switch status 1 ON 2 Transfer speed 19200 bits/s OFF 3 p / OFF 4 Data length 8 bits ON 5 Parity check Odd parity ON 6 Parity check Odd parity OFF 7 Stop bit length 1 bit OFF 8 Control signals CS, RS invalid OFF PLC communication cable: D-sub 9-pin loose-wire cable (AIP81842) 1 2 3 4 5 6 7 8 9 L 50/1.97 (Unit: mm/inch) Made by JAE: DE-C8-J9-F1-1 Made by JAE: DE-9PF-N 10/0.39 (shielded mesh wire section) Signals on D-sub side Pin no. Wire color Dot mark 1 Brown Black dot 2 Brown Red dot 3 Yellow Black dot 4 Yellow Red dot 5 Green Black dot 6 - - - - 7 Green Red dot 8 - - - - 9 - - - - Specifications L Order no. D-sub 9-pin Single-side loose wiring AIP81841 AIP81842 1 m/3.28 ft 2 m/6.56 ft Connecting to the FP3 computer communication unit (CCU) 1 FG SD RS SG CS RD 2 3 4 5 6 N.C. 7 8 9 N.C. ER SD SD RD CS GND RS RD RS CS GND 1 2 3 4 5 6 7 8 9 GT10 Pin no. on PLC side No. 3 (yellow: black dot mark) No. 2 (brown: red dot mark) No. 7 (green: red dot mark) No. 4 (yellow: red dot mark) Short wiring here No. 5 (green: black dot mark) PLC side GT10 side Pin no. Pin no. Abbreviation Abbreviation all-guides.co m

48 4.7 Connecting the FP-M 4.7 Connecting the FP-M 4.7.1 Connecting to the COM. Port AIP81842 GT10 FP-M COM. port FP-M communication format settings System register no. Item Value Set System register value 412 Selection of target use of RS232C port Computer link K1 413 Data length 8 bits K3 Parity check Yes Parity setting Odd Stop bits 1 bit Line return code CR Start code No STX 414 Baud rate setting 19200 bits/s K0 415 Unit number 1 K1 416 Modem connection No connection H0 PLC communication cable: D-sub 9-pin loose-wire cable (AIP81842) 1 2 3 4 5 6 7 8 9 L 50/1.97 (Unit: mm/inch) Made by JAE: DE-C8-J9-F1-1 Made by JAE: DE-9PF-N 10/0.39 (shielded mesh wire section) Signals on D-sub side Pin no. Wire color Dot mark 1 Brown Black dot 2 Brown Red dot 3 Yellow Black dot 4 Yellow Red dot 5 Green Black dot 6 - - - - 7 Green Red dot 8 - - - - 9 - - - - Specifications L Order no. D-sub 9-pin Single-side loose wiring AIP81841 AIP81842 1 m/3.28 ft 2 m/6.56 ft

GT10 49 4.7 Connecting the FP-M Connecting to the FP-M COM. Port 1 FG SD RS SG CS RD 2 3 4 5 6 N.C. 7 8 9 N.C. ER SD SD RD CS GND RS RD RS CS GND 1 2 3 4 5 6 7 8 9 GT10 Pin no. on PLC side No. 3 (yellow: black dot mark) No. 2 (brown: red dot mark) No. 7 (green: red dot mark) No. 4 (yellow: red dot mark) Short wiring here No. 5 (green: black dot mark) PLC side GT10 side Pin no. Pin no. Abbreviation Abbreviation

50 4.7 Connecting the FP-M 4.7.2 Connecting to the TOOL Port 19200 AIGT8192 GT10 FP-M TOOL port FP-M communication format settings System register no. Item Value Set System register value 410 Unit number 1 K1 411 Data length 8 bits H0 Modem connection No connection PLC communication cable: Mini-DIN 5-pin loose-wire cable (AIGT8192) 3 5 4 1 2 7/0.28 30/1.18 2000/78.74 (Unit: mm/inch) Connector: Made by JST Mfg. Co., Ltd.: MD-P15B (housing A) MD-P16A (housing B) MD-PS8T (shell) MD-SP2240 x 5 (terminal) Mini-DIN plug side signals 1 SG Brown 2 SD Red 3 RD Orange 4 - - - - 5 - - - - Pin no. Abbreviation Wire color Specifications L Product No. 2 m/6.56 ft Mini-DIN 5-pin Single-side loose wire AIGT8192 Connecting to the FP-M TOOL port GT10 3 5 4 1 2 No. 1 (brown) Pin no. on PLC side No. 3 (orange) No. 2 (red) 1 SG 2 SD 3 RD 4 - - 5 - - PLC side Pin no. Abbreviation SD SD RD RD RS RS CS CS GND GND GT10 side Pin no. Abbreviation

GT10 51 4.8 Automatic Communication Settings Function 4.8 Automatic Communication Settings Function After turning on the power supply, if there is no response from the PLC connected to the GT10, the GT10 switches to the automatic setting mode for the communication conditions. In the automatic setting mode, commands are sent to the PLC while changing the communication conditions in the sequence shown below. GT10 PLC (1) 9600 bits/s, 8 bits, odd parity, 1 stop bit (2) 19200 bits/s, 8 bits, odd parity, 1 stop bit (3) 115200 bits/s, 8 bits, odd parity, 1 stop bit (4) Communication conditions set in GTWIN Configuration Settings If there is no response from the PLC, commands are sent to the PLC while changing the communication conditions. The GT10, in automatic setting mode, continues to repeat steps (1) to (4) until there is a response from the PLC. While it is repeating these steps, it is in the “Standby” mode under “GT10 Configuration” a “Communication Parameters” a “Handle Communication Error” on GTWIN. For information on how settings are entered, please refer to page 61. Explanation of this function • Conditions when the automatic settings mode is in effect If communication is attempted the specified number of times and there is no response from the PLC, the GT10 goes into the automatic settings mode. The number of attempts is specified using the “No. of Retries” parameter under “GT10 Configuration” →“Communication Parameters” →“Handle Communication Error” on GTWIN. For information on how settings are entered, please refer to page 61. • Automatically set communication conditions In the automatic settings mode, if there is a response from the PLC, subsequent communication is carried out under conditions matching the response. The main unit configuration settings are not updated, however, even if the communication parameters are different from those of the main unit configuration settings.

52 4.8 Automatic Communication Settings Function CAUTION • An error response from the PLC is taken as a response, and the GT10 does not go into the automatic settings mode. • If the GT10 is connected to the COM. port of the FP0, FP1, FP2, FP2SH, or FP-M, the automatic communication settings mode functions only if the usage objective of the RS232C port is set to “Computer Link”. Always set the setting on the PLC side to match “Computer Link”. For detailed information, please refer to Chapter 4, “Connecting and Communicating With the PLC”, on page 35. all-guides.co m

GT10 53 4.9 Through Function 4.9 Through Function With the GT10, communication can be set to take place automatically between the COM. and TOOL ports in a “through function”. When the FP series tool software installed in the computer connected to the GT10 as shown below is booted, PLC programs can be edited through the GT10. The through function does not require any special settings, and is always in the standby mode. PLC GT10 Connected by cable to the COM. port or TOOL port of the PLC Screen transfer cable AFC8503 Screen data being sent and received Screen creation tool GTWIN FP series programming tool FPWIN GR Personal computer The FPWIN GR and NPST-GR are booted on the computer being used to edit the GT10 screens, and the PLC programs can be edited and monitored through the GT10. PLC debugging

54 4.9 Through Function CAUTION • Precautions when using the through function The system should be set up so that the interval for communication retries in the FP series software (FPWIN GR or NPST-GR) (A) is larger than that of the GT10 COM. port (B), meaning (A) > (B). If the system is set up so that A = B or A < B, the through function will not work properly. • Restrictions on COM. port connections If the GT10 is connected to the COM. port of the PLC, please be aware that some functions cannot be used, such as rewriting in the RUN mode in the FPWIN GR. • Precautions when connecting the FP Programmer II to the TOOL port If the FP Programmer II is connected to the TOOL port of the GT10, the operating voltage of the GT10 should be set to 25V DC or less. Also, the GT10 should not be left connected to the FP Programmer II on an ongoing basis. GT10 FP Programmer II 25V DC max.

This chapter describes the configuration settings for the GT10, and how they should be entered. 5.1 GT10 Configuration Settings 57 . . . . . . . . . . . . . . . . . . . . . . . . 5.1.1 Two Types of GT10 Configuration Settings 57 . . . . 5.2 Entering Configuration Settings from GTWIN Screen Creation Tool 58 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.2.1 Opening the GT Configuration Settings 58 . . . . . . . 5.2.2 GT Configuration Settings: “Basic Setup” 59 . . . . . 5.2.3 GT Configuration Settings: “Communication Parameters” 61 . . . . . . . . . . . . . . . 5.2.4 GT Configuration Settings: “Auto-Paging” 64 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.2.5 GT Configuration Settings: “Startup Screen Settings” 66 . . . . . . . . . . . . . . . . . . . 5.2.6 GT Configuration Settings: “Setup” 68 . . . . . . . . . . . 5.2.7 GT Configuration Settings: “Hold PLC Device” 71 . . . . . . . . . . . . . . . . . . . . . . . . . 5.3 Entering Configuration Settings from the GT Main Unit 73 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.3.1 What is the System Menu? 73 . . . . . . . . . . . . . . . . . 5.3.2 Bringing Up the System Menu 73 . . . . . . . . . . . . . . . next page

56 5.3.3 Setting Mode: “Communication Parameters” (COM. Port / TOOL Port) 74 . . . . . . . . . . . . . . . . . . . 5.3.4 Setting Mode: “Liquid Crystal Display Contrast Adjustment” (Contrast) 76 . . . . . . . . . . . . . 5.3.5 Setting Mode: “Clock Settings” (Clock) 76 . . . . . . . 5.3.6 Setting Mode: “Memory Initialization” (Clear Memory) 78 . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.3.7 Test Mode: “Self-Diagnosis” 79 . . . . . . . . . . . . . . . . 5.3.8 Inhibiting the System Menu Display 80 . . . . . . . . . .

GT10 57 5.1 GT10 Configuration Settings 5.1 GT10 Configuration Settings Before using the GT10 for the first time, it must be set up by entering the GT10 configuration settings indicated below. Always check and enter the settings under “Basic communication area to PLC”. For instructions on setting up the GT10, see page 30. 5.1.1 Two Types of GT10 Configuration Settings 1. Entering configuration settings from GTWIN screen creation tool page 58 . . With this method, GT10 configuration settings are entered from GTWIN screen creation tool, and the GT10 configuration file is sent to the GT10. Most items can be set using this method. GTWIN GT10 GT10 configuration file sent 2. Entering configuration settings from the GT main unit page 73 . . . . . . . . . . . . . Some of the settings, such as the communication parameters, the internal clock, and adjustments of the liquid crystal display contrast, can be set using the system menu of the GT10. Settings are entered using the touch switches on the front of the panel. GT10 Explanation of this function Items in the GT10 Configuration Settings Items that can be set from GTWIN Items that can be set either way Items that can be set from the GT10 system menu Title setting Communication parameters Clock division setting for the internal clock Type of PLC connected LCD contrast setting Basic communication area to PLC Communication parameters Communication parameters Memory initialization Auto-paging screen settings Self-diagnosis Startup screen (default screen) settings Reference destination setting for clock Backlight control Touch sounds Hold PLC device all-guides.co m

58 5.2 Entering Configuration Settings from GTWIN Screen Creation Tool 5.2 Entering Configuration Settings from GTWIN Screen Creation Tool This section describes how configuration settings for the GT10 are entered from GTWIN screen creation tool. 5.2.1 Opening the GT Configuration Settings The GT configuration settings are set by selecting [Configuration] on the menu displayed by clicking with the mouse on [File] or pressing the Alt + F keys. Then select the “GT Configuration” sub-menu under [Configuration]. Configuration Settings GTWIN Configuration - - - These are operating environment settings for GTWIN. GT Configuration - - - These are configuration settings for the GT10. The file is sent from GTWIN to the GT10 after the settings have been entered.

GT10 59 5.2 Entering Configuration Settings from GTWIN Screen Creation Tool 5.2.2 GT Configuration Settings: “Basic Setup” Selecting [Configuration] on the [File] menu of GTWIN and then the sub-menu [GT Configuration] displays the “Basic Setup” screen shown below. This is used to specify the basic communication area used for communication between the GT10 and PLC, and the environment required for GT10 operation. “Basic Setup” screen Title - - - The title of the configuration settings file is entered here. Titles are convenient if each GT10 has its own configuration settings. PLC Model - - - The model of PLC specified when GTWIN is booted is displayed here. GT Model - - - The model of GT specified when GTWIN is booted is displayed here. Basic communication area to PLC This is used to specify the mode in which communication takes place between the GT10 and PLC, and the internal PLC device used for basic communication. Modes Turn on the radio button for either “GT10 Mode” or “IOP01 Mode”. - GT10 Mode - - - Select this if you are using the GT10 for the first time. - IOP01 Mode - - - This mode is for users who are using a conventional model (I.O.P. B01C / M01L / D01TL). If this mode is selected, the basic communication area for communication between the GT10 and PLC is compatible with conventional models for the most part, except for a few items. REFERENCE For information on the IOP01 mode, please see page 33, “IOP01 Mode”.

60 5.2 Entering Configuration Settings from GTWIN Screen Creation Tool Device used This specifies the internal PLC device used for basic communication between the GT10 and PLC. · Word area - - - This specifies the type of device that reads and writes screen numbers and other information in word units, and the initial address. · Bit area - - - This specifies the type of device that reads and writes backlight control and other bit information, and the initial address. The type of device and addresses can be set by clicking on the buttons for the various items. Device settings dialog box Clicking on the button displays a pull-down menu. Select the device for which settings are to be entered, and use the ten-keys to enter addresses. The button functions as a backspace key when entering addresses. The button acts as a Clear key. REFERENCE For detailed information on the basic communication area map, see “Basic Communication Area Map” on page 32. Explanation of this function Standard settings Clicking on the button in the “GT Configuration” dialog box displays the following message. Clicking on [OK] sets the default values (the configuration settings entered when the unit is shipped) for all of the settings. For information on the contents of configuration settings entered when the unit is shipped, see “Contents of configuration settings when shipped from the factory” on page 27.

GT10 61 5.2 Entering Configuration Settings from GTWIN Screen Creation Tool 5.2.3 GT Configuration Settings: “Communication Parameters” Clicking on the “Communication Parameters” tab in the “GT Configuration” dialog box displays the following screen. This is where communication parameters for the PLC and personal computer (GTWIN) connected to the GT10 are set. “Communication Parameters” screen COM. port (Connected to PLC/External Device) This is used to specify the communication speed and transmission format when the GT10 is connected to an external device (PLC). Clicking on the button displays a pull-down menu from which the value to be set can be selected. · Baud Rate - - - Select 9600, 19200, 38400, 57600, 76,800 or 115200 bits/s. · Data Length - - - Select either “7 bits” or “8 bits”. · Stop Bits - - - This is fixed at “1 bit”. · Parity Bit - - - Select “None”, “Odd”, or “Even”.

62 5.2 Entering Configuration Settings from GTWIN Screen Creation Tool Handle Communication Error Clicking on the button displays the “Communication Error Remedy” dialog box. This is used to specify the processing to be used if a communication error occurs. “Communication Error Remedy” dialog box For “Retry” and “Waiting”, click the button and specify the values in the “Value Set” dialog box that is dis- played. For “Display Error Code”, select “Off”, “On (Hold)”, or “On (Unhold)” by click- ing the radio button of the desired val- ue to turn it on. Retry - - - This specifies the number of retries if a communication error occurs. The setting range is from 0 to 255 times. Waiting - - - This specifies the interval between retries if a communication error occurs. The setting range is from 0 to 255 seconds. all-guides.co m

GT10 63 5.2 Entering Configuration Settings from GTWIN Screen Creation Tool “Display Error Code” This switches the setting for the error code display used if a communication error occurs. Off - - - No error code is displayed if a communication error occurs. On (Hold) - - - An error code is displayed at the upper right of the screen if a communication error occurs, and continues to be displayed until the power supply is turned off. On (Unhold) - - - An error code is displayed at the upper right of the screen if a communication error occurs, and is cleared when the cause of the error is eliminated. For contents of error codes, please see “Error Codes and How to Handle Them” on page 102. TOOL Port (for GTWIN connection) This is used to specify the communication speed and transmission format when the GT10 is connected to a personal computer (GTWIN). Clicking on the button displays a pull-down menu from which the value to be set can be selected. · Baud Rate - - - Select 9600, 19200 or 115200 bits/s. · Data Length - - - This is fixed at “8 bits”. · Stop Bits - - - This is fixed at “1 bit”. · Parity Bit - - - Select “None”, “Odd”, or “Even”. Through function If the “Forward only to the selected unit” check box is turned on, communication can be carried out via the through function only with unit numbers for a PLC received from a higher-order personal computer or higher-order PLC.

64 5.2 Entering Configuration Settings from GTWIN Screen Creation Tool 5.2.4 GT Configuration Settings: “Auto-Paging” Clicking on “Auto-Paging” in the “GT Configuration” dialog box displays the screen shown below. Here, settings can be entered for a functions that automatically switches the screens displayed on the GT10. “Auto-Paging” screen Auto-paging This is used to specify the “Auto-paging function”, which automatically switches the specified screen when a given period of time has elapsed. Off - - - The screen is not switched automatically. On - - - The screen is switched automatically, in conformance with the specified contents.

GT10 65 5.2 Entering Configuration Settings from GTWIN Screen Creation Tool Auto-paging settings If “On” is selected for auto-paging, and the [Setup] button is clicked, a dialog box containing the following auto-paging settings is displayed. Clicking on the button for “Screen No.”, “Time”, or “Jump to” displays a “Value Set” dialog box. Set the value and click the [Save] button to save values one at a time. Screen No. - - - This specifies the screen targeted for auto-paging. Time - - - This specifies the time for which the screen specified above is displayed. The setting range is from 1 to 255 seconds. Jump to - - - This specifies the number of the next screen to be displayed. [Return] - - - This completes the auto-paging settings and returns to the “Auto-Paging” dialog box. [Delete] - - - This deletes screens registered for auto-paging. [Save] - - - This saves the settings for the screen number, time, and jump destination as auto-paging settings.

66 5.2 Entering Configuration Settings from GTWIN Screen Creation Tool 5.2.5 GT Configuration Settings: “Startup Screen Settings” Clicking on “Start-up Screen” in the “GT Configuration” dialog box displays the screen shown below. Here, the screen displayed when the GT10 is booted can be specified. “Start-up Screen” screen This is used to specify the screen that will be displayed when the GT10 is booted, as well as the time it will be displayed. Clicking on the button for each of the items displays a “Value Set” dialog box where the values can be specified. Start-up Screen No. - - - This specifies the number of the screen that will be displayed when the GT10 is booted. Clicking on the button displays a “Value Set” dialog box where the value for the start-up screen number can be specified. Display Time - - - This specifies the time for which the startup screen specified above will be displayed. The value can be set to any number between 0 and 255 seconds. Clicking on the button displays a “Value Set” dialog box where the start-up delay time can be specified. Key points • When the above settings are entered, the screen specified with the “Startup Screen No.” parameter is displayed for the amount of time specified with the “Display Time” parameter. • When the amount of time specified with the “Display Time” parameter elapses, the screen corresponding to the number stored in the initial address of the word device under “Basic Communication Area to PLC” in the “Basic Setup” parameters under “GT Configuration” will be displayed. • This function is used when it is necessary to delay the start-up time when the power supply on the PLC side is turned on.

GT10 67 5.2 Entering Configuration Settings from GTWIN Screen Creation Tool CAUTION • Communication between the GT10 and the PLC (external device) cannot be carried out during the time specified by the “Display Time” parameter. all-guides.co m

68 5.2 Entering Configuration Settings from GTWIN Screen Creation Tool 5.2.6 GT Configuration Settings: “Setup” Clicking on the “Setup” tab in the “GT Configuration” dialog box displays the screen shown below. Here, clock functions, backlight control, and other parameters can be specified. “Setup” screen Clock Clock This is used to specify the reference destination for the clock displayed with the GT10. Select one of the radio buttons. GT Clock - - - When the time is displayed, the internal clock in the GT10 is used as a reference for the value. PLC Clock - - - When the time is displayed, the internal clock in the PLC is used as a reference for the value. If the “PLC Clock” is referenced for the clock setting, clicking on the button displays a screen where the type of device and the address can be specified. Device Setting dialog box The button functions as a backspace key when entering addresses. The button acts as a Clear key. Click on the button to display the pull-down menu, and select the device from that menu. Enter the address using the ten-keys.

GT10 69 5.2 Entering Configuration Settings from GTWIN Screen Creation Tool Transfer Outside Clock data displayed in the GT10 can be transferred to an external device such as a PLC, using this setting. Off - - - The GT10 clock data is not transferred to an external device. On - - - The GT10 clock data is transferred to an external device. If “On” is selected for the above “Transfer Outside” parameter, click on the button to specify the output destination and the initial device, and specify the address. Data storage sequence for internal PLC device Upper byte Lower byte Top address Minutes data (H00~H59) Second data (H00~H59) Top address +1 Day data (H01~H31) Hour data (H00~H23) Top address +2 Year data (H00~H99) Month data (H01~H12) CAUTION If “On” is selected for the “Transfer Outside” parameter, the data will be transferred to the DT90054 as the default device. If this device address does not exist in the PLC connected to the GT10, however, re-specify the address so that it matches the model connected to the GT10. Selecting a device address that does not exist in the PLC will cause an error (ER61) to occur.

70 5.2 Entering Configuration Settings from GTWIN Screen Creation Tool Backlight control Auto-Off This is used to specify the Auto-Off backlight feature. Off - - - The Auto-Off backlight feature is not used. On - - - Auto-Off backlight feature is used. This parameter specifies the period of time that the GT10 is inactive before the backlight goes off automatically. If “On” is set for the above Auto-Off backlight feature, clicking on the button displays a screen where the time until the backlight goes off can be specified. Any time from one minute to 30 minutes can be specified. Key points If the backlight is turned off automatically using the backlight control function, touching the screen turns it on again. If a touch switch happens to be located at that point on the screen, it will be invalid until the backlight has gone on again. Touch Sounds This sets the touch sounds corresponding to GT10 screens as either invalid or valid. Select one of the radio buttons. Disable - - - Touch sounds are disabled. Enable - - - Touch sounds are enabled.

GT10 71 5.2 Entering Configuration Settings from GTWIN Screen Creation Tool 5.2.7 GT Configuration Settings: “Hold PLC Device” Clicking on the “Hold PLC Device” tab in the “GT Configuration” dialog box displays the screen shown below. “Hold PLC Device” is a function that enables internal PLC device values to be held on the GT10 side. “Hold PLC Device” screen Hold PLC Device The Hold PLC Device function reads the values for the specified internal PLC device to the SRAM in the GT10, and backs up the values. Off - - - PLC devices are not held. On - - - PLC devices are held (up to 24 words) If “On” is selected for the above Hold PLC Device setting, “Device” and “Number of Word” parameters are displayed. Clicking on the button displays a dialog box like that shown below, where the type of initial device, the address, and the number of words can be specified. Device Setting dialog box Click on the button to display the pull-down menu, and select the device from that menu. Enter the address using the ten-keys. The button functions as a backspace key when entering addresses. The button acts as a Clear key.

72 5.2 Entering Configuration Settings from GTWIN Screen Creation Tool CAUTION • Data for PLC devices held in the GT10 will be written to the internal PLC device the next time that the power supply is turned on. • If the power supply on the GT10 side is not turned on, the data can be held for the period of time that the backup with the internal secondary battery is effective. For information on the internal secondary battery specifications, see “What the Internal Secondary Battery Does” on page 93. all-guides.co m

GT10 73 5.3 Entering Configuration Settings from the GT Main Unit 5.3 Entering Configuration Settings from the GT Main Unit 5.3.1 What is the System Menu? The system menu is a dedicated screen on which configuration settings for the GT10 are entered. Some of the items that can be specified here can also be set using GTWIN screen creation tool and then sent to the GT10, but others, such as the internal clock and adjustments to the LCD contrast level, can only be set using the system menu. This section explains how configuration settings are entered using the system menu. 5.3.2 Bringing Up the System Menu The following procedure is used to bring up the system menu. (1) Touch the four corners of the LCD touch panel simultaneously. Touch these four corners at the same time, and continue pressing them for about one second. (2) The initial screen of the system menu is displayed. The initial screen of the system menu is displayed on the GT10. Touching either the [Setting] or [Test] key shifts to the next screen. Touching the [ESC] key exits the system menu and returns to the normal operating mode. *.* indicates the ROM version of the GT10 system. (3) Select the mode. [Setting]: Setting mode initial screen This is where configuration settings for the GT10, such as the contrast, clock, COM. port, TOOL port, and memory, are specified. [Test]: Test mode initial screen This is where GT10 configuration elements such as the touch switches, backlight, clock, buzzer, LCD, contrast, and memory are tested.

74 5.3 Entering Configuration Settings from the GT Main Unit 5.3.3 Setting Mode: “Communication Parameters” (COM. Port / TOOL Port) Touching the [Setting] key on the initial screen of the system menu and then touching the [COM. Port] and [TOOL Port] keys on the setting mode menu displays the communication parameters setting screen. Here, parameters controlling communication between the PLC and personal computer (GTWIN) connected to the GT10 are specified. COM. port communication parameter settings (PLC communication parameter settings) Procedure for bringing up the screen [Initial screen] [Setting] [COM. port] ↓ ↓ Bitrate: PLC communication speed This sets the communication speed, or Baud rate, for communication with an external device (PLC) connected to the GT10. Each time the [Function] key is pressed, the Baud rate switches in the sequence of 9600, 19200, 38400, 57600, 76800, 115200 bits/s. Set the speed to match that of the PLC connected to the GT10. Format: Transmission format This sets the communication parameters (data length, stop bits, parity) for the external device (PLC) connected to the GT10. The items displayed are: Data length / Stop bit / Parity, and each time the [Function] key is pressed, the display switches in the sequence of: [7/1/None], [7/1/Odd], [7/1/Even], [8/1/None], [8/1/Odd], [8/1/Even]. Set the parameters to match those of the PLC connected to the GT10. Learning the shortcut keys saves time! [RETURN]To complete the settings and return to the previous screen, touch the [ESC] key. Explanation of this function COM. port communication parameter settings The default (initial) values for the COM. port communication parameter settings are: 19200 bits/s, 8/1/Odd.

GT10 75 5.3 Entering Configuration Settings from the GT Main Unit TOOL Port communication parameter settings (GTWIN communication parameter settings) Procedure for bringing up the screen [Initial screen] [Setting] [TOOL Port] ↓ ↓ Through function: Through function destination setting When the through function is being used, this specifies the number of the PLC at the other end of the connection. Normally, when used in a 1 : 1 configuration, this should be set to “00”. Bitrate: GTWIN communication speed Each time the [Function] key is touched, the Baud rate switches in the sequence of 9600/19200/115200 bits/s. Set the speed to match that of the personal computer (GTWIN) connected to the GT10. Format: Transmission format This sets the communication parameters (data length, stop bits, parity) for the personal computer (GTWIN) connected to the GT10. The items displayed are: Data length / Stop bit / Parity, and each time the [Function] key is pressed, the display switches in the sequence of: [8/1/None], [8/1/Odd], [8/1/Even]. Learning the shortcut keys saves time! [RETURN]To complete the settings and return to the previous screen, touch the [ESC] key. Explanation of this function TOOL Port communication parameter settings The default (initial) values for the TOOL Port communication parameter settings are: 19200 bits/s, 8/1/Odd.

76 5.3 Entering Configuration Settings from the GT Main Unit 5.3.4 Setting Mode: “Liquid Crystal Display Contrast Adjustment” (Contrast) Touching [Setting] on the initial screen of the system menu and then the [Contrast] key of the setting mode menu displays the contrast adjustment screen. The contrast of the GT10 LCD is adjusted here. Contrast adjustment screen Procedure for bringing up the screen [Initial screen] [Setting] [Contrast] ↓ ↓ Learning the shortcut keys saves time! [ADJUST] Touching the [+] key increases the contrast, and touching the [-] key decreases it. [RETURN]To complete the settings and return to the previous screen, touch the [ESC] key. 5.3.5 Setting Mode: “Clock Settings” (Clock) Touching [Setting] on the initial screen of the system menu and then the [Clock] key of the setting mode menu displays the clock setting screen. The internal clock of the GT10 is set here. Clock setting screen Procedure for bringing up the screen [Initial screen] ↓ [Setting] ↓ [Clock] The time displayed on the screen is the current time indicated by the internal clock of the GT10. Items can be changed by touching the item (year, month, day, hour, minute, second) and touching the [+] and [-] keys to change the values.