Miele professional PM 1210 Operating Instructions Manual

PM 1210 PM 1214 PM 1217 To avoid the risk of accidents or damage to the appliance, it is essential to read these instructions before it is installed and used for the first time. en-AU, NZ M.-Nr. 10 026 131

Warning and Safety instructions........................................................................................ 5 Correct application................................................................................................................ 5 Technical and electrical safety ............................................................................................. 5 Operation............................................................................................................................... 6 Using accessories ................................................................................................................ 6 Notes on the use of this flatwork ironer ............................................................................... 6 Guide to the appliance........................................................................................................ 8 Touch display ........................................................................................................................ 9 Display symbols .................................................................................................................. 11 Finger guard ........................................................................................................................ 12 Swing out bar ...................................................................................................................... 13 Flexible laundry feed for throughfeed or return feed........................................................... 13 Using for the first time ...................................................................................................... 14 Cleaning and waxing the heater plate before first use........................................................ 14 Operation............................................................................................................................ 15 Preparing the laundry .......................................................................................................... 15 Residual moisture...........................................................................................................  15 Preparing for use................................................................................................................. 15 Ironing.................................................................................................................................. 15 Ironing temperature ........................................................................................................  16 Setting the temperature..................................................................................................  16 Changing the preset temperature for a temperature selection button ...........................  16 Selecting the ironer speed .............................................................................................  16 Setting the ironer speed.................................................................................................  17 Changing the preset roller speed for a roller speed selection button ............................  18 Laundry feed ..................................................................................................................  18 Pauses in ironing ............................................................................................................  19 Standby mode................................................................................................................  19 FlexControl foot switch ..................................................................................................  19 Pick-off bands................................................................................................................  19 After ironing......................................................................................................................... 20 Ironing with a coin-operated payment system.................................................................... 20 Notes .................................................................................................................................. 21 Changing the temperature unit (°C / °F) .............................................................................. 21 Favourites setting ................................................................................................................ 21 Avoiding no-load operation ................................................................................................. 21 Power failure during ironing................................................................................................. 21 Peak load / Energy management (optional) ........................................................................ 21 Fault messages ................................................................................................................... 22 Cleaning and care ............................................................................................................. 23 Cleaning the heater plate .................................................................................................... 23 Starting the cleaning programme...................................................................................  23 Cleaning with the cleaning cloth ....................................................................................  24 Waxing the heater plate....................................................................................................... 25 Waxing using the waxing cloth.......................................................................................  25 Roller padding ..................................................................................................................... 26

Fitting the roller cover.....................................................................................................  27 Miele Professional Service .................................................................................................. 27

4 Disposal of the packing material The transport and protective packaging has been selected from materials which are environmentally friendly for disposal, and can normally be recycled. Recycling the packaging reduces the use of raw materials in the manufacturing process and also reduces the amount of waste in landfill sites. Ensure that any plastic wrappings, bags etc. are disposed of safely and kept out of the reach of babies and young children. Danger of suffocation. Disposing of your old appliance Electrical and electronic appliances often contain valuable materials. They also contain specific materials, compounds and components, which were essential for their correct function and safety. These could be hazardous to human health and to the environment if disposed of with your domestic waste or if handled incorrectly. Please do not, therefore, dispose of your old appliance with your household waste. Please dispose of it at your local community waste collection / recycling centre for electrical and electronic appliances. You are also responsible for deleting any personal data that may be stored on the appliance prior to disposal. Please ensure that your old appliance poses no risk to children while being stored prior to disposal.

5 Please read these instructions carefully before using the flatwork ironer for the first time. They contain important information on the safety, use and maintenance of the flatwork ironer. This prevents both personal injury and damage to the appliance. If other persons are being shown how to operate the flatwork ironer, they must be given these important safety instructions and/or be made aware of them. Keep these instructions in a safe place and pass them on to any future owner. Correct application This flatwork ironer must be used as described in these instructions and must be checked on a regular basis to make sure it is functioning correctly. Maintenance must be carried out when necessary.  This flatwork ironer must only be used for ironing articles which were washed in water and which have a care label stating that they are suitable for machine ironing.  This flatwork ironer is intended for use in commercial settings. This appliance is not designed for domestic use. If the flatwork ironer is operated in a publically accessible place, it is the operator's responsibility to ensure suitable measures are in place to protect users from any source of risk or danger.  This flatwork ironer is not suitable for outdoor use. Technical and electrical safety  This flatwork ironer should not be operated in the same room as dry-cleaning equipment using perchloroethylene or solvents containing CFCs.  This flatwork ironer should only be operated in a suitably dry room.  Only operate this flatwork ironer when all removable outer panels are in place so that it is impossible to touch an electrical component or moving part.  Do not damage, remove or bypass the safety components or control elements of this flatwork ironer.  Do not make any alterations to the flatwork ironer unless authorised to do so by Miele.  If the controls or the electrical cabling insulation have been damaged, this flatwork ironer must not be used until it has been repaired.  Repairs and other work by unqualified persons could be dangerous. The manufacturer cannot be held liable for unauthorised work. Repairs may only be carried out by a Miele authorised service technician.  Faulty components must only be replaced by genuine Miele Original spare parts. The manufacturer can only guarantee that the machine fully complies with safety requirements when Miele replacement parts are used.  The electrical safety of this flatwork ironer can only be guaranteed if connected to a correctly installed earthing system on site. It is most important that this standard safety requirement is present and tested regularly and, where there is any doubt, the on-site electrical system should be tested by a qualified electrician. Miele cannot be held liable for damage or injury caused by the lack of or inadequacy of an effective earthing system.

6  This flatwork ironer is only completely isolated from the electricity supply when switched off at the mains circuit breaker or it is switched off at the wall socket and the plug is withdrawn from the socket (if applicable). Operation  This flatwork ironer must not be operated unsupervised.  This flatwork ironer is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience or knowledge, unless they are supervised whilst using it or have been shown how to use it in a safe way and understand and recognise the consequences of incorrect operation.  Please supervise children in the vicinity of the flatwork ironer and do not let them play with it.  In the heated state and with the heater plate contacting the roller, there is a serious risk of burning if the edge of the heater plate on the laundry output side is touched.  Do not set the ironing temperature higher than the temperature given on the care label of the item you intend to iron. The laundry could ignite if the ironing temperature is set too high.  When ironing double layered items, do not reach in between the layers to straighten out the fabric. This is extremely dangerous as you may not be able to extract your hands in time. The same applies when ironing garments with pockets.  The flexible laundry feed mechanism (depending on model) must only be operated from the front.  Ensure the room in which the flatwork ironer is being used is sufficiently lit.  Keep the working area around the flatwork ironer free from clutter.  Always keep a fire extinguisher accessible in the rare event of textiles igniting. Items which are unsuitable for ironing or which have not been washed in water can catch fire. Using accessories  Accessory parts may only be fitted when expressly approved by Miele. If other parts are used, warranty, performance and product liability claims will be invalidated.  Coin operated ironers must be anchored to the floor by the supporting feet to prevent the risk of the machine tipping. Notes on the use of this flatwork ironer  Only responsible people over the age of 16 years who have been fully trained in the use of the flatwork ironer should use the infeed table.  When working with the flatwork ironer, always wear close fitting clothes and keep long hair tied back. Wide sleeves, apron straps, scarves and ties etc. could be taken in by the roller.  Remove rings and bracelets before ironing.

7  Smooth out folds as far away from the infeed on the infeed table as possible. Feed pillow cases and duvet covers into the ironer with the open end first. Do not take hold of the corners from the inside. Do not take hold of straps or ties etc. from the inside of garments.  Check daily that safety devices are correctly set. This flatwork ironer must only be used if all safety features are functioning correctly. This way you will avoid the danger of burns, squashed fingers and even loss of hands.  Before switching to reverse, make sure that nobody is endangered. If other persons are being shown how to operate the flatwork ironer, they must be given or made aware of these important safety instructions. Pass these instructions on to any future users/owners of the flatwork ironer.

8 a Control panel (touch display) b Infeed table c Finger guard d Roller e Heater plate with cover f Laundry outfeed table g FlexControl foot switch h Pick-off bands i Height-adjustable screw feet j Plinth (optional) k Laundry box Option PM 1210 PM 1214 PM 1217 Swing out bar X Flexible laundry feed X Leaf-spring padding X Plinth X X X

9 Touch display The buttons on the touch display can be activated by a light touch with the finger. When a button is pressed, it is highlighted with a bar underneath.             Display in temperature selection mode a Button  For switching the flatwork ironer on and off. b Button  For pausing the ironing process. c Button  For starting the ironing process. Button flashes when the ironing process can be started. d Button  Temperature selection mode e Temperature selection button  For nylon and rayon fabrics. f Temperature selection button  For woollen and silk fabrics. g Temperature selection button  For cotton and linen fabrics. h Button  For increasing the ironing temperature. i Button  For decreasing the ironing temperature. j Button  Favourites setting k Button * Maintenance position for carrying out maintenance work. Press and hold the button for at least 3 seconds to activate or deactivate. * depending on the model, this button is displayed or hidden l Button  Function for cleaning and waxing the heater plate. Press and hold the button for at least 3 seconds to activate or deactivate.

10             Display in roller speed selection mode a Button  For switching the flatwork ironer on and off. b Button  For pausing the ironing process. c Button  For starting the ironing process. Button flashes when the ironing process can be started. d Button . For switching to roller speed selection mode. e Roller speed selection button  Low speed range f Roller speed selection button  Medium speed range g Roller speed selection button  High speed range h Button  For increasing the roller speed. i Button  For decreasing the roller speed. j Button  Favourites setting k Button * Maintenance position for carrying out maintenance work. Press and hold the button for at least 3 seconds to activate or deactivate. * depending on the model, this button is displayed or hidden l Button  Function for cleaning and waxing the heater plate. Press and hold the button for at least 3 seconds to activate or deactivate.

11 Display symbols 1  Prompt to activate the finger guard 2  Heating on / temperature increasing 3  Service indicator for cleaning and waxing 4  Heating off / temperature decreasing 5  General fault 6  or  Constant laundry feed on left or right side 7  Pre-selection and temperature display in °C/°F 8  Pre-selection and roller speed display 9 // Roller speed range 10  Coin operation mode 11 °C/°F For switching between temperature units °C or °F.

12 Finger guard The finger guard is a safety feature which must be checked daily for proper functioning before the machine is used. Risk of injury due to lack of finger guard function! A malfunctioning finger guard function can lead to serious injury. Shut down the flatwork ironer immediately. Contact Miele without delay. Ensure that the flatwork ironer is not put into operation by other persons and draw attention to the potential hazard. The ironer will only switch to the normal operating mode if the finger guard has been activated properly after switching on the ironer. Otherwise, the ironer will switch off again after a short period of time. Activate the finger guard once when the  symbol flashes in the display. If finger tips get between the roller and the finger guard, the roller is stopped immediately and the heater plate is withdrawn. If this happens, the  symbol will light up constantly. The ironer can be turned on again by pressing the  button. While the ironer is operating, do not use the finger guard intentionally to interrupt the ironing process. Always interrupt the ironing process by pressing the  button.

13 Swing out bar (Optional accessory for PM 1214) Ironed laundry can be placed over the swing out bar to prevent creasing. Flexible laundry feed for throughfeed or return feed (Optional accessory for PM 1217) The flexible laundry feed mechanism enables laundry to be fed through to the back of the ironer for removal. It is particularly suitable for larger items of laundry such as sheets/duvet covers or table cloths. The flexible laundry feed for the reverse removal of laundry should be applied only from the front. Do not touch the edge of the heater plate. Danger of burning!

14 Cleaning and waxing the heater plate before first use Before using for the first time, the heater plate must be cleaned and waxed (see “Cleaning and care”). Clean the heater plate by passing through a Miele cleaning cloth along the entire width of the roller. Then wax the heater plate with an ironer waxing cloth and ironer wax. Use the wax sparingly.

Residual moisture For a good result and optimum ironing performance the laundry should have the following residual moisture levels, depending on model: PM 1214, PM 1217: 15-25% residual moisture PM 1210: 15% residual moisture The ideal residual moisture level depends on the composition of the fabric. Preparing for use Switch on the on-site mains switch. Press the  button to switch on the flatwork ironer. The red  symbol will flash in the display. Activate the finger guard by lifting it. The ironer switches to the normal operating mode. The ironer is only ready to use if the finger guard has been activated properly. Otherwise, the ironer will switch off again after a short period of time. The red  symbol will appear in the display and the flatwork ironer will heat up. Ironing After switching the flatwork ironer on, wait until it has reached the minimum ironing temperature. The  button begins to flash as soon as the minimum temperature has been reached. The flatwork ironer is ready for operation when the set temperature is reached and the  symbol no longer appears in the display. Now press the flashing  button to start up the flatwork ironer. The ironing process can begin. Useful tip: Allow the roller to rotate for about 5 minutes to enable the heat to equalise between the heater plate and the roller. Danger of burning on the edge of the hot heater plate! There is a warning sticker on the heater plate housing to warn of the danger of burning.

Fabric Symbol Temperature Preset value Nylon/rayon  100 - 110 °C 110°C Silks/woollens  111 - 150 °C 125°C Cottons/linens  151 - 185 °C 180°C Temperature selection buttons The temperature can be selected either by using the temperature selection buttons or the  and – buttons. If a higher ironing temperature is reduced to a lower temperature, the flatwork ironer must be allowed to cool down first. This will turn off the heating of the ironer. The red  display symbol will indicate that the current ironing temperature is still too high. As soon as the  display symbol goes out, the selected temperature has been reached. Setting the temperature Press the   button on the control panel to call up the temperature selection mode. The   button will be highlighted with a bar underneath. Press one of the three temperature selection buttons. (e.g. temperature selection button ) The button is highlighted with a bar underneath and the ironer is heated up or cooled down to the selected temperature. Changing the preset temperature for a temperature selection button Press the temperature selection button you want to change the value for. Keep it pressed in. The bar will light up underneath it and the current temperature value will appear in the display. Press the  or – button to set the temperature you want to save for that button. Then press and hold the selected temperature selection button until it flashes once. The temperature value is now saved for that temperature selection button. Useful tip: Allow the roller to rotate for about 5 minutes to enable the heat to equalise between the heater plate and the roller.

Symbol Speed range m/min  Low speed range 1.5 - 2.2  Medium speed range 2.3 - 3.2  High speed range 3.3 - 4 PM 1217 Symbol Speed range m/min  Low speed range 1.5 - 2.4  Medium speed range 2.5 - 3.4  High speed range 3.5 - 4.5 Speed selection buttons The roller speed can be set either by using the speed selection buttons or the  and – buttons. Setting the ironer speed Press the . button to call up the roller speed selection mode. The button will be highlighted with a bar underneath. Press one of the three roller speed buttons. (e.g. button ) The selected roller speed button will be highlighted with a bar underneath, and the flatwork ironer will operate at the preset roller speed for this button.

speed selection button Press the roller speed button that you want to change the speed for. Keep it pressed in. The bar will light up underneath it and the current speed will appear in the display. Press the  or – button to set the roller speed you want to save for that button. Then press and hold the selected roller speed button until it flashes once. The roller speed is now saved for that roller speed button. Laundry feed Press the  button to start the ironing process. The heater plate engages and the roller starts to turn. Items with buttons should be passed through the ironer with the buttons facing in to the roller padding. If they face upwards, they could be damaged or torn off when the item is passed through the ironer. A cloth should be placed over zips, metal buttons and hooks to protect the heater plate during ironing. Metal and plastic buckles and very bulky buttons should not be passed through the flatwork ironer. Lay the item parallel to the roller at the start of the laundry infeed ta- ble. Smooth the item. Feed the item evenly into the machine. Do not restrict ironing of smaller articles to any one part of the roller. Otherwise heat is transferred on one side only, and the roller cover is worn down unevenly. If laundry is continuously fed in from one and the same side of the roller, the red symbol  or  will light up in the display and an alarm will sound. Make use of the whole roller width and distribute smaller items evenly on the infeed table.

Press the  button to go into Pause mode. The heater plate is disengaged and the roller comes to a standstill. The heating will remain switched on. Press the  button to start ironing again. The flatwork ironer remains on and ready to operate in Pause mode. After an adjustable period of non-use (factory default setting = 10 minutes), the temperature can be reduced to a value between 50–70 °C (factory default setting = 60 °C). The values must be set at the service level by Miele Professional Service. After a period of inactivity which can be preset, the ironer will switch to standby mode. Standby mode Standby mode is switched off at the factory. It can be reactivated by Miele Professional Service. The time interval after which the flatwork ironer switches to Standby mode can be set between 1 minute and 30 minutes of inactivity. The ironer can be switched on again by pressing the  button. In Standby mode the roller stops turning and the heater plate is disengaged. The heating is switched off. FlexControl foot switch Activating the moveable foot switch stops the roller. This helps to avoid input mistakes. Stopping the roller During ironing, press down the FlexControl foot switch with your foot. The roller will stop. The heater plate remains engaged. Remove your foot from the foot switch to continue ironing. When the foot switch is released, the roller starts to turn again automatically. The ironing process can continue. The foot switch can also be configured by Miele Professional Service so that operating the foot switch ends Pause mode, engages the heater plate and makes the roller start turning. Pick-off bands The pick-off bands are used for picking laundry off the roller. The ironed laundry can be very hot when it comes out of the heater plate. Danger of burning! Wear gloves to protect your hands if necessary.

temperature to let the roller covering dry out. Switch the flatwork ironer off by pressing the  button. The heater plate will disengage and the fan will run for 10 minutes to cool down. The  button will flash during this time. Switch off the on-site main switch. Allow the ironed laundry to cool down before packing or stacking it. Hot laundry could self-ignite and cause a fire. Ironing with a coin-operated payment system Press the  button to switch on the flatwork ironer. The  symbol will flash in the display. Insert the coin or token. The  symbol will go out in the display. Select the temperature range according to the type of laundry. Select the roller speed you want. When the  symbol goes out in the display, the flatwork ironer is ready to operate and the ironing time purchased will begin to count down. Press the  button to start the ironing process. The heater plate engages and the roller starts to turn. After the purchased ironing time has expired, the ironer emits an audible signal to indicate that the run-on time has started. You can now finish ironing the item that has been fed in. If the ironing process is paused during the run-on time, you must purchase more ironing time to restart the flatwork ironer. Miele Professional Service can change the duration of the run-on time to a value between 0–5 minutes. At the end of the run-on time, the heater plate disengages and the roller comes to a standstill. The  symbol flashes in the display. More ironing time can be purchased at any time.

The temperature unit can be changed from °C to °F by Miele Professional Service. Favourites setting Using the Favourites  button, the most used combination of temperature and roller speed can be saved so that they can be accessed quickly and easily. To save the desired parameters, press the  button until it flashes once. The saved values are then accessed by pressing the  button briefly. When you leave the Favourites setting, the previously saved values are restored again. Avoiding no-load operation During longer interruptions to ironing, press the  button to pause the machine, or switch the ironer off with the  button. This avoids running the flatwork ironer without laundry and considerably relieves the burden on the roller cover and the drive motor. If the ironer is operated empty for a longer period of time, the roller cover will dry out. This will substantially reduce the lifespan of the roller cover. Power failure during ironing If there is a power outage, the flatwork ironer must be switched on again by pressing the  button, activating the finger guard and pressing the  button. Peak load / Energy management (optional) The flatwork ironer can be connected to a peak load/energy management system using a kit which is available as an optional accessory. If the peak load/energy management system is active, the heater plate is switched off and  or . flash in the display. The residual heat in the heater plate means that ironing can continue until the ironer goes into Pause mode ().

four-digit code appears in the display. Pressing the flashing  button cancels the fault (the fault is stored in the fault memory). The  button flashes and ironing can be restarted. Fault code Fault F 0 Heater fault F 1 F 2 F 8 F 20 F 24 F 25 F 39 Electronic fault F 40 F 41 F 42 F 43 F 45 F 47 F 49 F 50 Drive fault F 53 F 57 Fan fault F 61 Electronic fault F 99 Appliance locked F 104 Drive voltage too low F 108 General compressor fault F 120 Low voltage F 4500–4512 Control system fault If the fault message appears again, repeat the procedure or switch the ironer off and back on. If the fault persists, please call Miele Professional Service. In the event of a malfunction, please call Miele Professional Service.

23 Cleaning the heater plate Regular cleaning and maintenance of the heater plate is essential for the protection of the drive motor and the roller cover. Please follow the notes in the Miele Ironing Handbook on ironing and cleaning and care. The heater plate must be waxed every time it is cleaned. Failure to do so can result in a considerable reduction of the lifespan of the flatwork ironer. The heater plate is made of aluminium. For this reason, do not use coarse scouring agents or abrasive cleaning cloths. Only use the Miele cleaning set for cleaning. It includes a cleaning cloth, waxing cloth, and ironer wax. The set is available to order as an optional accessory. Detergent and starch deposits can stick to the heater plate. It should therefore be cleaned before starting work, depending on the degree of soiling. The ironers PM 1210, PM 1214 (from serial No. 120610687 onwards) and PM 1217 (from serial No. 120610797 onwards) all come with a cleaning and waxing indicator (red indicator symbol ). When the red indicator symbol  lights up, it is necessary to run the cleaning programme to clean and wax the heater plate. Starting the cleaning programme Press and hold the  button for more than 3 seconds. The cleaning programme is started. 80 °C is shown in the display. If the current temperature of the ironer is higher than 80 °C, the  symbol appears and the ironer is cooled down. You can start cleaning as soon as the symbol has gone out and a temperature of 80 °C is displayed.

24 Cleaning with the cleaning cloth Use the Miele cleaning cloth for cleaning the heater plate. As the cleaning cloth is narrower than the heater plate, the entire plate cannot be cleaned in one go. It is necessary to feed the cleaning cloth through the ironer several times, gradually moving it down the width of the heater plate. Useful tip: Stubborn soiling such as starch deposits can be removed by passing a cloth soaked in lukewarm water through the ironer. ① ② ③ a Pocket b Cleaning strip c Cotton strip Place the cleaning cloth on the left side of the infeed table so that the cleaning strip faces towards the heater plate. Feed the cleaning cloth evenly into the ironer from the left side of the infeed table until it has passed all the way through the ironer. The cleaning strip helps to lift the soiling. The softer cotton strip removes the soiling and polishes the heater plate. 1. 2. 3. Feeding the cleaning cloth through the ironer from left to right Place the cleaning cloth on the infeed table again, this time slightly further to the right. The cleaning strip must face the heater plate.

25 Feed the cleaning cloth through the ironer again. Repeat the process until you have arrived at the right side of the infeed table and have cleaned the entire width of the heater plate. The heater plate must be waxed after every cleaning process. Waxing the heater plate To start the waxing function, first press the  button for a minimum of 3 seconds and then the temperature selection button . As soon as the flatwork ironer has reached the  temperature range, the  button starts flashing. To deactivate the waxing function, press the  button again and hold it for a minimum of 3 seconds. When waxing has been completed for at least 40 seconds in the waxing function, the timer for the prompt to clean and wax the heater plate (red indicator symbol ) is reset. Waxing using the waxing cloth Sprinkle some wax into the pocket of the waxing cloth. Use the wax sparingly to prevent the roller cover becoming too smooth. Close the pocket. Press the  button to start the waxing process. Lay the pocket with the rubberised side facing downwards (i.e. towards the roller) and feed it into the flatwork ironer when hot (heater plate temperature approx. 180 °C). Do not feed the waxing cloth with the rubberised side facing upwards (i.e. towards the heater plate).

26 1. 2. 3. Feed the waxing cloth into the ironer from the left or right side at intervals across the entire working width of the roller. When finished, press and hold the  button for a minimum of 3 seconds. The waxing mode is deactivated. Useful tip: To maintain the smooth surface of the heater plate, it should be waxed after every working day. Always carry out cleaning in the cleaning programme and waxing in waxing mode, as otherwise the ironer's maintenance interval will not be reset. The maintenance interval is only reset once cleaning and waxing have been carried out completely in the corresponding mode. Roller padding Before removing the roller cover for cleaning or replacing, switch off the flatwork ironer and allow the heater plate to cool down. Removing the roller cover The roller cover on the PM 1217 with leaf-spring padding must only be removed or replaced by Miele Professional Service. Otherwise there is the risk of damage to the leaf-spring padding. Please note that the laundry pick-off bands on the roller need to be fully retracted one after the other before removing the roller cover. Switch on the flatwork ironer by pressing the  button. Press the  button for more than 3 seconds. The heater plate disengages and is locked into this position. By repeatedly pressing the - button, incrementally rotate the roller in reverse (jogging mode). Take hold of the edge of the roller cover and lay it on the laundry infeed table. With the roller in reverse, fully remove the roller cover. After that, press the  button for longer than 3 seconds to deactivate the maintenance position.

27 Wire wool residues may fall onto the laundry table whilst the roller cover is being removed. These must be removed. Fitting the roller cover Switch on the flatwork ironer by pressing the  button. Select the lowest temperature () and the lowest roller speed (). While operating the ironer normally, place the roller cover on the ironer parallel to the roller and feed the roller cover over the roller. The roller cover needs to be changed if there is a visible gap at the lower edge of the heater plate and roller (laundry outfeed) due to prolonged use. Recovering the roller with wire wool must only be carried out by Miele Professional Service. The diameter of a new or re-upholstered roller must not exceed the following dimensions (including the roller cover). PM 1210, PM 1214 PM 1217 210-215 mm 250-255 mm Within this range the roller cover should be wound cylindrically over the entire length of the roller. During the replacement of the roller padding, Miele Professional Service should check whether the carbon brushes in the drive motor need to be replaced as well. Miele Professional Service In the event of a malfunction, please call Miele Professional Service. Miele will require the model and serial number [SN] of the flatwork ironer. Both can be found on the data plate which is on the inside of the right side stand. Position of the data plate

ACN 005 635 398 ABN 96 005 635 398 1 Gilbert Park Drive Knoxfield, VIC 3180 Telephone: 1300 731 411 [email protected] Melbourne: www.miele-professional.com.au [email protected] Miele New Zealand Limited IRD 98 463 631 Level 2, 10 College Hill Freemans Bay Auckland 1011 New Zealand Telephone: www.miele-professional.com.au [email protected] Miele Global Headquarters Germany Miele & Cie. KG Carl-Miele-Straße 29 33332 Gütersloh Federal Republic of Germany 0800 4 MIELE (0800 464 353) Alteration rights reserved / Publication date: 47.18 M.-Nr. 10 026 131 / 01 