Schlage CONNECT Quick Start Manual
Read Online
Read the Schlage CONNECT Quick Start Manual online using the built-in PDF viewer.
Text of the manual
Backup Key
Touchscreen
Assembly
Backplate
Reinforcement
Plate
Bolt
Strike
Reinforcement
Screws
Inside Assembly
Screw
Backplate
Screws
Bolt/Strike
Screws
Parts
Set Screw
Battery
Cover
Inside
Assembly
Thumbturn
For an improved installation experience, follow the
link below or scan the QR code for online interactive
instructions, warranty, and reference information.
https://instructions.allegion.
com/instr/86/2110
Don’t use a power drill!
Phillips screwdriver
1 2 3 4 5
U.S.A.: 888-805-9837
Canada: 800-900-4734
Mexico: 018005067866
Support
See “Help with Step 1” in the online
instructions. The link is on the back
cover or the third page of this guide.
1
step
Actual Size
Make sure the
word “TOP” is
facing up.
Install the bolt.
You may have to adjust your bolt length. Make sure the slot in
the bolt is centered in the hole.
Slot is
centered
in the hole.
No change
needed.
Twist the
faceplate to
extend.
Keep
twisting
until 2 ¾”.
Install the strike into the door frame.
2
step
Actual Size
Actual Size
Install
this strike
reinforcer for
enhanced
security.
Need Help?
Trouble installing the strike reinforcer? See
“Help with Step 2” in online instructions.
If you have a window next to your door, you may not be able
to use the longer wood screws to install the reinforcer.
Install the touchscreen.
Route the cable through the door BELOW the bolt. Align the
tailpiece as shown and push the touchscreen onto the door.
Is it hard to install the touchscreen?
Is the tailpiece not installing correctly?
If the hole through your door seems
too small, you may need to remove the
spacer. See the online instructions.
The bump on the
tailpiece aligns
with the slot in the
bolt.
Install the inside backplate.
Route the cable below the bolt and through the hole on the
bottom of the backplate. Secure the backplate with screws.
Hold the touchscreen
on the outside of
the door while you
tighten the screws.
TOP
Make sure
that “TOP”
is facing
out.
Actual Size (2)
Don’t use a power drill!
You may damage your lock!
Phillips screwdriver
1 2 3 4 5
Secure the lock to the door.
7
step
Align bump on
tailpiece with notch.
If the bump on the tailpiece doesn’t align with the slot in the
back of the inside assembly, make sure your thumbturn is vertical
(up and down). Tuck the wire into the channel.
Tuck
wire.
Install the screws.
Actual Size
Actual Size
Install the lower screw first.
1st
2nd
Don’t use a power drill!
You may damage your lock!
Phillips screwdriver
1 2 3 4 5
Set up your lock.
1. Open your door!
2. Enter one of the two default user
codes.
The codes are located on the back
of this guide and on the back of
the inside assembly. You need to
remove the inside assembly to see
the label.
3. Your lock will enter a setup routine.
When the bolt stops moving, setup
is complete.
10
step
Test your lock.
1. Close your door.
2. Extend and retract the bolt using the inside thumbturn.
3. Make sure the bolt retracts smoothly. If it doesn’t your door
and frame may not be aligned.
4. Open your door.
5. Extend the bolt using the inside thumbturn.
6. Now enter a user code at the touchscreen to check that the
bolt retracts.
If the bolt doesn’t extend or
retract during testing, see the
online instructions and make sure
spindle is aligned properly.
Need Help?
Enroll your lock.
1. Place your smart home system or
panel into enrollment mode (see
documentation for that device for
details).
2. Remove the battery cover.
3. Press then release button.
4. A yellow flashing light indicates
enrollment is in progress.
5. A solid green light indicates
successful enrollment.
L
L A red light indicates
an enrollment issue, try
repeating steps 1-3.
12
step
Lock and unlock
To unlock your door
enter a user code.
To lock your door just
tap the
logo.
You can also lock your door by
entering a user code while the door
is closed or by turning the thumbturn
toward the door edge.
You can also unlock your door from
inside by turning the thumbturn away
from the door edge.
Add and delete codes
Enter the user
code you’d
like to add or
delete.
Press
1
Enter
Programming
Code
(6 digits)
2
4
add or delete another
user code
Enter that
code again.
5
indicates
success
•• The lock supports user codes
between 4 and 8 digits and is set
to a default length of 4 digits.
•• The first 4 - 6 digits must be
different from the first 4 - 6 digits
of the programming code.
Choose
and press:
or
add
delete
3
Factory default reset
1. Disconnect
your batteries.
2. Press and hold
down the
logo.
While you are pushing
the logo, reconnect
your batteries.
3. Test your lock
with one of your
default codes,
located on the
back of this
guide.
If you have forgotten your programming code, you can restore the
default codes. If you want to move the lock to a different door, you
need to restore default settings. Move the lock to the new door,
and then set it up again.
Now set
up your
lock, see:
10
step
© Allegion 2018
Printed in U.S.A.
P518-669 Rev. 06/18-b
Save this guide!
*P518-669*
P518-669
PLACE LABEL
HERE
PLACE LABEL
HERE
https://instructions.
allegion.com/
instr/86/2110
Access step-by-step
instructions and help.
