AT&T 146 Operation & User’s Manual

AT&T Corp. licensed to Advanced American Telephones. © 2000 Advanced American Telephones. All rights reserved. Printed in China. 850005059 Issue 1AT&T 12/00 1 USER’S MANUAL Part 2 INSTALLATION Please also read Part 1 – Important Product Information Design Line® Telephone 146 2 4 Pull phone down onto mounting studs as shown. 5 Follow Steps 3-5 in Table/Desk, above. Table/Desk Wall 3 Press the cord into the channel as shown, and connect to the free end of the line cord to the modular wall jack. 2 Connect the short line cord to the telephone. 1 Reverse the handset tab as shown. 1 Connect the long line cord to the telephone. 2 Press the cord into the channel as shown, and connect the free end of the line cord to the modular wall jack. 3 Set the dial mode switch to TONE if you have touch tone service or to PULSE if you have dial pulse service. 4 Connect the handset to the base using the coiled cord. Hang up the handset. 5 Lift the handset and check for dial tone. Dial mode switch b c a NOTE: If you do not reverse the handset tab, the handset will not stay in the cradle when used on a wall. If you later move this phone to a table or desk, be sure to reverse the handset tab again. Dial mode switch

If you have difficulty operating this phone, try the suggestions below. For Customer Service, visit our website at www.telephones.att.com or call 1 800 222-3111. Please retain your receipt as your proof of purchase. No Dial Tone • Make sure all plugs are connected properly. Inspect the line cord connections at the modular jack and at the telephone. Also inspect the coiled handset cord connections at both ends. • Unplug the telephone and connect it to another modular jack. If it still does not work, try another telephone; if neither telephone works the problem is not in this telephone. Contact your telephone service provider. Calls Cannot Be Dialed or Are Dialed Slowly Check the dial mode switch; make sure it is set for your type of dialing service (TONE or PULSE). Telephone Does Not Ring or Rings Too Softly • Make sure the RINGER switch is not set to OFF. • You may have inadvertently turned off the ringer when selecting a ringer tone. Press , #, 6, to turn the ringer back on. • You might have too many extension phones on your line to allow all of them to ring. Try unplugging some of them. You Can Hear Other Party but Other Party Can’t Hear You The Mute feature might be activated. Try pressing . If this doesn’t work, try pressing again. OPERATION Select Ringer Tone You can select from three different ringer tones. The phone comes set to Tone 2. 1 Press . 2 Press #. 3 Press 3 for Tone 1 — OR — Press 6 for Tone 2 — OR — Press 9 for Tone 3. 4 Press to save your selection. Store Memory Numbers This phone can store 10 telephone numbers, each up to 21 digits long. 1 Lift the handset. 2 Press . 3 Press m. 4 Enter a memory location (0 - 9) where the number is to be stored. 5 Enter the telephone number. You’ll hear a click each time you press a button. 6 Press . 7 Hang up. 8 Repeat Steps 1 to 7 to store another number. Dial Memory Numbers 1 Lift the handset and listen for a dial tone. 2 Press m. 3 Press the memory location (0 - 9). Erase Memory Numbers To erase any number from memory, store another number in its place. NOTE: Memory numbers and redial memory will be lost if the phone is unplugged from wall jack for more than 30 minutes. Directory Card A directory card is provided for your convenience to record numbers stored in memory. OPERATION Adjust the volume of what you hear through the handset from NORMAL to LOUD. Adjust the volume of the ringer from OFF to LO to HI. Dial the last number called from this phone (up to 31 digits). To erase redial memory, lift the handset, press any digit, then hang up. Access special telephone company subscriber services such as Call Waiting. Change from dial pulse to tone dialing during a call. 1 Dial the number. 2 Press *. All buttons pressed after this send tone signals. 3 After you hang up, the phone returns to dial pulse service. While on a call, press to prevent the other party from hearing you (you can still hear the other party). Press again to return to two-way conversation. 3 4