Optical Systems Design OSD2512 Quick Start Manual

DOC ID: 10116701 OSD2512 QUICK START GUIDE PAGE 3 INDEX 1 1 INTRODUCTION ...................................................................................................................... 4 2 INSTALLATION........................................................................................................................ 4 3 OSD2512 FRONT AND REAR PANELS................................................................................. 5 3.1 FRONT PANEL ....................................................................................................................... 5 3.2 REAR PANEL ............................................................................................................................ 5 4 POWER SUPPLY CONNECTIONS ........................................................................................ 6 5 LED INDICATORS ................................................................................................................... 7 6 FITTING SFP CONNECTORS ................................................................................................ 8 7 CLI OVERVIEW ....................................................................................................................... 9 7.1 CONNECT TO CLI ...................................................................................................................... 9 7.2 CLI COMMAND FOR IP CONFIGURATION ................................................................................. 10 8 GUI OVERVIEW ..................................................................................................................... 11 8.1 DEFAULT SETTING................................................................................................................... 11 8.2 LOG INTO THE SWITCH ............................................................................................................ 11 8.3 IP CONFIGURATION ................................................................................................................. 11 8.4 USERS AUTHENTICATION ........................................................................................................ 12 8.5 SAVE CONFIGURATION TO START-UP ...................................................................................... 13 9 WARRANTY ............................................................................................................................ 14 9.1 WARRANTY PERIOD .......................................................................................................... 14 9.2 REPAIRS ................................................................................................................................ 14 9.2.1 WARRANTY REPAIRS .................................................................................................... 14 9.2.2 OUT-OF-WARRANTY REPAIRS .................................................................................... 14 9.2.3 SITE REPAIRS .................................................................................................................. 14 9.2.4 EXCLUSIONS ................................................................................................................... 14 FIGURE 1: FRONT PANEL .................................................................................................................... 5 FIGURE 2: REAR PANEL ...................................................................................................................... 5 FIGURE 3: POWER CONNECTION ...................................................................................................... 6 FIGURE 4: FITTING/REMOVING SFP CONNECTORS ..................................................................... 8 TABLE 1: DC POWER CONNECTION ................................................................................................. 6 TABLE 2: LED FUNCTION ................................................................................................................... 7

DOC ID: 10116701 OSD2512 QUICK START GUIDE PAGE 4 1 INTRODUCTION Thank you for choosing the OSD2512 14-Port Gigabit Managed Ethernet Switch. This Quick Start Guide is designed to guide you through the installation and basic software function. 2 INSTALLATION ELECTROMAGNETIC COMPATIBILITY WARNING: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. OPTICAL OUTPUT OPERATION WARNING: Laser Safety: Class 1 Laser Product (SFP) per IEC 60825-1:2014 standard. Class 1 The OSD2512 is a Class 1 laser product. PRECAUTIONS ▲ All service personnel should be provided training as to the hazards of direct viewing of laser radiation and of the precautionary measures during servicing of equipment ▲ Areas where laser products are installed should be restricted in access to trained service personnel only and appropriate warning signs posted in the work area. ▲ All laser apertures should be covered by protective covers when not connected to optical fibers. Never leave outputs uncovered. ▲ Laser equipment should be positioned above or below eye level where possible. Apertures should be positioned away from personnel. ▲ Protective eyewear should be worn in the vicinity of laser equipment.

DOC ID: 10116701 OSD2512 QUICK START GUIDE PAGE 5 3 OSD2512 FRONT AND REAR PANELS 3.1 FRONT PANEL FIGURE 1: FRONT PANEL 1. Board Status LED 2. USB Console Port 3. View LED Mode Button 4. View Mode LEDs Indicators 5. Copper Port Status LEDs 6. RJ45 Copper Ports 7. SFP Fiber LED 8. SFP Fiber Ports 9. SFP Fiber LED 10. Reset Button 3.2 REAR PANEL FIGURE 2: REAR PANEL 11. Earth 12. Power 1 LED 13. Dual Redundant Power Input 14. Power 2 LED 1 2 3 4 5 6 7 8 9 10 11 12 13 14

DOC ID: 10116701 OSD2512 QUICK START GUIDE PAGE 6 4 Power Supply Connections Connect the dual redundant power to the 4-way terminal block located on the rear of the unit. The OSD2512 requires external +10 to +36VDC @ 40VA Max power. FIGURE 3: POWER CONNECTION TABLE 1: DC POWER CONNECTION External Power Pin Specification Pin 1, Pin 3 0V (Ground Isolated) Pin 2, Pin 4 +10 to +36VDC @ 40VA max

DOC ID: 10116701 OSD2512 QUICK START GUIDE PAGE 7 5 LED Indicators TABLE 2: LED FUNCTION Function Board Status LED • Green – Normal status • Red Blinking – Internal Warning View Mode LED Indicators Controlled by View LED Mode Button. Pressing the Mode button cycles the Copper Port Status LED indication. Speed Mode � Duplex Mode � Status Mode � Reserved �. Copper Port Status LED The Copper Port Status LED will indicate different information. Speed Mode: • Green – 1Gbps • Yellow – 100MBps • Off – No Connection • Blinking - Traffic Duplex Mode: • Green – Full Duplex • Yellow – Half Duplex • Off – No Connection • Blinking - Traffic Status Mode: • Green – Connection good • Off – No Connection Fiber Port Status LED • Green – 1Gbps • Off – No Connection • Blinking - Traffic

DOC ID: 10116701 OSD2512 QUICK START GUIDE PAGE 8 6 Fitting SFP Connectors Care should be taken when inserting/removing the SFP connectors from the SFP port as SFP modules are Electrostatic (ES) sensitive and Electrostatic Discharge (ESD) precautions should be taken when installing. Ensure that the SFP is fully engaged and latched into position. Inserting SFP – Ensure that the SFP lever is in the locked position and insert into appropriate SFP port. Gently push the SFP until it locks into place. Remove plastic/rubber dust cap and fit appropriate fiber cable. Removing SFP – Remove fiber connector. Pull the SFP lever down to unlock SFP from housing. Using the lever, gently pull the SFP out. Fiber SFP FIGURE 4: FITTING/REMOVING SFP CONNECTORS Inserting SFP Removing SFP 1 2

DOC ID: 10116701 OSD2512 QUICK START GUIDE PAGE 9 7 CLI OVERVIEW 7.1 CONNECT TO CLI The Silicon Laboratories CP210x VCP Drivers is needed to be installed on the PC before connecting the switch.

DOC ID: 10116701 OSD2512 QUICK START GUIDE PAGE 10 1. Connect the Console Port on UUT to PC with USB cable (Type A to Type B). 2. Using HyperTerminal to set up the following parameters. • Baud Rate: 115200 • Data Bits: 8 • Parity: None • Stop Bits: 1 • Flow Control: None 3. Check the link by pressing . The line should jump to the next line. 4. Using the Username and password to login the switch • Default Username: admin • Default Password: (None) 7.2 CLI COMMAND FOR IP CONFIGURATION • show ip interface brief: Display the current IP address and subnet mask. • configure terminal -> interface vlan 1 -> ip address : Setup the switch IP address. • copy running-config startup- config: Save the current configuration to start-up configuration. PS: All configuration changes must be saved otherwise all the changes will be lost after rebooting!

DOC ID: 10116701 OSD2512 QUICK START GUIDE PAGE 11 8 GUI Overview 8.1 DEFAULT SETTING • IP Address: 192.168.0.99 • Subnet Mask: 255.255.255.0 • Gateway: 192.168.0.1 • User Name: admin • Password: (None) 8.2 LOG INTO THE SWITCH • Connect a switch port to a PC, Change the PC’s network IP address to connect to the switch (i.e.: 192.168.0.2). • In a web browser, enter the URL 192.168.0.99. • Enter the username and password. 8.3 IP CONFIGURATION In the treemap on the left, expand the Configuration -> System -> IP. Enter the IPv4 address and Mask Length in the table. Choose the management VLAN ID to access that IP in VLAN table if VLAN function is required. If the multiple IP addresses are required, click Add Interface to add more IP interface. Click Save to save the configuration. Use new IP address to access the switch. PS: All configuration changes must be saved otherwise all the changes will be lost after rebooting!

DOC ID: 10116701 OSD2512 QUICK START GUIDE PAGE 12 8.4 USERS AUTHENTICATION In the tree map on the left, expand the Configuration -> Security-> Switch-> Users Click admin to change the current admin account setting. If multiple users are required, click Add New User

DOC ID: 10116701 OSD2512 QUICK START GUIDE PAGE 13 PS: All configuration changes must be saved otherwise all the changes will be lost after rebooting! 8.5 SAVE CONFIGURATION TO START-UP In the treemap below, expand the Maintenance and expand Configuration, then select Save startup- config Click Save Configuration to save the configuration on start-up.

DOC ID: 10116701 OSD2512 QUICK START GUIDE PAGE 14 9 WARRANTY Thank you for purchasing equipment designed, manufactured and serviced by Optical Systems Design (OSD). OSD warrants that at the time of shipment, its products are free from defects in material and workmanship and conforms to specifications. Our Warranty conditions are outlined below: 9.1 WARRANTY PERIOD For warranty period, please call your local OSD distributor. 9.2 REPAIRS Optical Systems Design reserves the right to repair or replace faulty modules/units. Please obtain a “Return Material Authorisation” (RMA) form and number before returning goods. Goods must be returned in adequate packing material to Optical Systems Design, Warriewood or its nominated authorised representative, for all repairs. 9.2.1 WARRANTY REPAIRS Return shipments to OSD shall be at customer's expense and freight back to the customer will be at OSD expense. 9.2.2 OUT-OF-WARRANTY REPAIRS OSD reserves the right to repair or replace any faulty goods. Freight costs and insurance for both journeys are met by the user. All equipment repaired by OSD will have a 3-Month Warranty from the date of dispatch. 9.2.3 SITE REPAIRS By agreement site repairs may be undertaken for which out of pocket, hotel and travel expenses will be charged. 9.2.4 EXCLUSIONS This warranty does not apply to defects caused by unauthorized modifications, misuse, abuse or transport damage to the equipment. All modifications to OSD’s standard product will need written authorization and will be charged at normal repair rates. All modifications are to be carried out by OSD Technicians. Warranty is void if unauthorized removal and/or tampering with serial number and/or repair labels is evident.

7/1 Vuko Pl. Warriewood 2102 P.O. Box 891 Mona Vale N.S.W. Australia 2103 Telephone: +61 2 9913 8540 Facsimile: +61 2 9913 8735 Email: [email protected] Web Site: www.osd.com.au OPTIC L SYSTEMS DESIGN PTY LTD A.B.N. 83 003 020 504 Printed in Australia