MobileVision M150-WL Operating Instructions Manual

and keep it for future reference. 2.4G 7 Inch Wireless Color LCD Monitor Digital V 1.2

6. Remote Control Operation 7. Basic Operation 8. Menu (1) Picture (2) Option (3) System 9. Troubleshooting 13 3. Technical Specifications 11 9 8 6 5 9 ………………………………………………………… ………………………………………………………… ……………………………………………………… ……………………………………………………… ……………………………………… ……………………………………………… ……………… ……………………………………… …………………………………………… …………………………………………………… ………………………………………………………… …………………………………………………… 4 3 3 1 12 ………………………………………………………… Contents (4) Auto Scan 13 ……………………………………………………

2. Observe polarity. power s do not device Make sure all cables are connected properly. Improper cable connections may damage the monitor. Remove the cable connection when you intend to use the . 1. High voltage is present within the monitor. The opening of the case should be by professionals. 2. Do not watch the video while driving unless you are monitoring the rear view camera display. ! Occasionally, a few highlights or dark spots may occur on the LCD screen. This is a very common phenomenon in active matrix display technology, and doesn’t necessarily indicate any defects or faults. Never try to repair this device by yourself. In case of any problems, please turn off the display at once and notify our company or authorized dealer. The monitor is a complex device. Any disassembly or modification may lead to damage and void the warrantee. ! Warning! 1. Precautions Special Notice 1 Storage and Keeping 1. Do not expose the monitor to excessive heat or cold. The storage temperature of this device is -30~+80℃, and the operating temperature is -20~+70 ℃. The humidity is RH90%. 2. Never use this device near a bathtub, wash basin, kitchen, damp basement, swimming pool or similar places. 3. Never use this device in environments with excessive moisture, dust or smoke. 4. Avoid dropping or striking this device. 5. Avoid using this device in enclosed spaces, areas with excessive vibration or subject to severe impacts. 6. Never puncture, scratch or use abrasive cleaning materials on this device. 7. Do not place cables where they may be pinched or stepped on. 8. Leave at least a 2" space between the monitor and walls, cabinets or other objects to allow adequate air circulation around the device. 9. The monitor is not designed to be waterproof.

2. Use a mild household detergent and clean the unit with a slightly damp,soft cloth. Never use strong solvents such as thinner or benzine, as they might damage the finish of the device. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. You are cautioned that any changes or modifications not expressly approved in this manual could void your warrantee and neccessitate expensive repairs. CAUTION This symbol is intended to alert the user not to waste electrical and electronic equipment. Declaration of conformity This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2 Maintenance

2.Picture image may be adjusted for Horizontal, Vertical, Mirror and Normal viewing. 3.Select from 8 languages for user operation. 4.Automatic back lighting for buttons. 5.Full-function remote control. 6.Multiple video formats: PAL/AUTO/NTSC. 7.Up to 4 wireless camera input,1video output and 1 audio output. 8.Operates from 10 -32V. Supports 12V or 24V automobile battery. 9. On-board speaker. 10.Automatic scanning function. 11.The scale can be adjusted for left, right, up and down. 12.Automatically switches to back-up,left,right or front camera views. 2. Features 1. Product: 7" Digital TFT- LCD Color monitor with built-in 2.4GHz wireless receiver. 2. Resolution: 800 x 3 (RGB) x 480 3. Contrast: 500:1 4. Brightness: 400cd/m2. 5.Viewing angle: U: 50 / D: 60, R/L: 70 6. Operation Frequency: 2400-2483.5MHZ 7. Line of Sight Range: 120M 8. Receiving Sensitivity: -78dBm 9. Video Codec: MPEG4 10. RF Band Width: 5MHZ 11. Frame Rate: PAL: 25f/s NTSC: 30f/s 12. Output Power: 18dBm 13. Spread Spectrum: FHSS 14. Hopping Rate: 1200/S 15. Delay: 200ms 16. RF Bit Rate: 6Mbps 17. Audio output: 1.5W 18. Loudspeaker: one 15x24mm round loudspeaker 19. Power supply: Automobile storage battery (10-32V) 20. Power consumption: about 8W 21. Outer dimension: 182mm (W) × 122mm (H) × 43mm (T) 22. Operating temperature: -20~+70ºC,RH90% 23. Storage temperature: -30~+80ºC,RH90%

! U- Support bracket Center mount bracket IR Remote control Angle adjustment screws Special Notice Power cable

Support attaching piece Brightness increase Brightness decrease Setting selection down Remote control sensor Automatic brightness control sensor Digital Color LCD screen Power indicator Power switch Menu Loudspeaker Select CAM1/CAM2/ CAM3/CAM4

2. Never disassemble the remote control or allow it to drop, or become wet. 3. Press the control buttons firmly. Allow 2 seconds for the picture to change. Setting Selection Up Setting Selection Down Power Switch 6. Remote Control Operation Less Brightness More Brightness PAL / AUTO / NTSC Call Select CAM1/CAM2/ CAM3/CAM4

POWER(Power switch) Press to set the time to shut down monitor (10,20,30,40,50,60,70,80and max 90 minutes). Press to select ENABLE/MUTE sound. SONAL / STANDARD / SOFT / VIVID / LIGHT). Press to select the upper setting. Press to select the lower setting or to display the scale. Press to decrease Brightness. Press to increase Brightness. : : LANG(Language Selection): Press to select language display of English, Deutsch, Français,Español,Português, Italiano, Nederlands or Русский options. SYS: Press to select PAL / AUTO / NTSC. Call Press to display video channel source SEL Press to select CAM channels

Angle adjustment screws Adjust the angle of the monitor and tighten the knob on the center mounting bracket. Adjust monitor level by sliding t desired height. he support to the 7.1. Installation of Center Mounting Bracket: 1 2 Knob Support attaching piece Single red wire to positive power supply of DC/10-32V. Single black wire to GND. Single brown wire to positive power wire of back-up light. Single white wire to positive power wire of left light . Single blue wire to positive power wire of right light . Single green wire to any other trigger control. Yellow RCA female for video output . White RCA female for audio output. DW-127D Brown Red Green White Black Blue Yellow RCA female White RCA female Video inputs Yellow RCA White RCA Monitor 1 2 3 DC/10-32V Trigger control POWER VOL VOL CH MENU V1/V2/V3 AV2 Automobile application Battery Battery + _ Camera DC/12V 4 5 6

1. PICTURE 2. OPTION 3. SYSTEM 4. AUTO SCAN (1) Picture BRIGHT,CONTRAST, COLOR, VOLUME, AUTO DIM and SCALE ADJUST options will display on the screen as illustrated below: Press CH- to select BRIGHT. PICTURE BRIGHT CONTRAST COLOR VOLUME 50 50 50 50 Press / to adjust the brightness level. AUTO DIM SCALE ADJUST OFF OFF 7.3.2. When the blue wire is connected to the positive wire of the right turn light, the monitor automatically switches to CAM2 (right side camera) when the right turn indicator is activated. 7.3.1. When the white wire is connected to the positive wire of the left turn light , the monitor automatically switches to CAM1 (left side camera) when the left turn indicator is activated. 7.3.Reversing Display: CAM1 CAM2 7.3.3. When the brown wire is connected to the positive wire of back-up light, the monitor automatically switches to CAM 3 (back-up camera) when the back-up light is turned on. The distancing grid will also be displayed. 7.3.4.When the green wire is activated,the monitor automatically switches to CAM4 CAM4 9

PICTURE BRIGHT CONTRAST COLOR VOLUME AUTO DIM SCALE ADJUST 50 50 50 50 OFF OFF Press / to select ↑↓ or for scale adjustment. ← When exit menu and press to display the grid line. CH- When auto dim is turned on in dark environment, OSD turns into dim mode for dim setting ; When auto dim is turned on / off in bright environment, OSD displays normal mode. PICTURE DIM BRIGHT DIM CONTRAST DIM COLOR VOLUME AUTO DIM SCALE ADJUST 40 45 40 50 ON OFF Dim mode PICTURE AUTO DIM SCALE ADJUST BRIGHT CONTRAST COLOR VOLUME 50 50 50 ON OFF Normal mode 50 If ↑↓ is selected, press / to adjust the scale up/down; If is selected press+/- to adjust the scale left/right. → ←→

as illustrated below : , , , , Press CH- to select LANG. Press / to select English, Deutsch, Français,Español,Português, Italiano, Nederlands or Русский. (2) OPTION Press / to select OFF/ON. Firstly press SEL to choose the channel to be paired, secondly press CH- to select PAIRING. Press / to select ON / OFF. Scale refers to the reversing distance indicator displayed on the monitor. Press CH- to select SCALE. OPTION SCALE PAIRING CAM1 CAM2 CAM3 CAM4 ON LANG ENGLISH OFF NORMAL NORMAL NORMAL NORMAL OPTION SCALE ON LANG ENGLISH OPTION SCALE ON LANG ENGLISH PAIRING CAM1 CAM2 CAM3 CAM4 OFF NORMAL NORMAL NORMAL NORMAL PAIRING CAM1 CAM2 CAM3 CAM4 OFF NORMAL NORMAL NORMAL NORMAL

When it counts down 50 seconds. PAIRING START Long press the “ PAIR” on the camera for 5 seconds. The screen shows “SAVE DATA” and picture, then code matching succeeds. SAVE DATA If code matching doesn’t complete in 50 seconds, the screen will show “PAIRING FAIL” to tell you that code matching fails and you need to try again.Other channels can be paired in the same way above. 50 (3) System COLOR-SYS, HORIZONTAL, VERTICAL, ZOOM functions will display on the screen as illustrated below : Press CH- to select COLOR-SYS . Press / to select PAL / AUTO / NTSC. SYSTEM COLOR -SYS HORIZONTAL VERTICAL ZOOM SYSTEM HORIZONTAL VERTICAL ZOOM COLOR -SYS AUTO 16:9

Upside down or lateral inverted picture Improper connection of automobile adapter. Use of un- authorized power supply. Power switch is on OFF position. Check whether AV cable is properly connected. Check whether audio wire is properly connected or the sound volume is turned off or set too low. Check whether brightness and contrast are adjusted correctly; Check whether the environments temperature is too low. Adjust the color settings. The black wire of the monitor AV cable to the reversing light may be loose. The red wire from the monitor may be loose. 9. Troubleshooting Use the remote control horizontal /vertical selection switch to set proper orientation No picture, no sound No picture No sound Dark picture No color No reversing function (i.e.Picture) The symptoms described below do not necessarily mean a failure within the display. Please check the following items before you initiate request for repair. Press / to select 16:9 or 4:3. Press CH- to select ZOOM. SYSTEM HORIZONTAL VERTICAL ZOOM COLOR -SYS PAL 16:9 (4) Auto Scan AUTO SCAN,SCAN TIME,CAM1,CAM2,CAM3 and CAM4 options display on the screen as illustrated below: Press CH- to select . SCAN TIME AUTO SCAN CAM1 CAM2 CAM3 OFF OFF OFF Press / to select 6S~90S. AUTO SCAN SCAN TIME OFF 6S CAM4 OFF