Oricom UHF390 Operating Instructions Manual

purchase in case of warranty service. AUSTRALIA: www.oricom.com.au NEW ZEALAND: www.oricom.co.nz Operating Instructions UHF390 80 Channel UHF Citizen Band Radio

and New Zealand approval requirements AS/NZS 4365:2011 Why has the ACMA increased the number of available UHF CB channels? To provide additional channel capacity within the UHF CB Band, the ACMA will over the next 5 years change the majority of the current wideband 40 channel use to narrowband 80 channel use. During this time wideband channel use will be gradually phased out as users upgrade their existing radio’s. This means that the new Oricom narrowband radio you have purchased will have more channels than older wideband radios. Some of these channels are locked and cannot be used, (see the attached channel chart for more information). When will this take place? Early in 2011 new AS/NZS Standards came into effect allowing operators to use additional narrowband channels and also use narrowband transmissions on some current wideband channels. This increased the number of channels up to 80, 75 of which are useable voice channels. What issues may users experience during the transition phase? When a new narrowband radio receives a transmission from an older wideband radio the speech may sound loud and distorted – simply adjust your radio volume for the best listening performance. When an older wideband radio receives a signal from a new narrowband radio the speech may sound quieter - simply adjust your radio volume for best listening performance. When operating a narrowband radio or Channel 41 - 80 interference is possible from wideband radios transmitting on high power or on adjacent frequency. The issues described above are not a fault of the radio but a consequence of mixed use of wideband and narrowband radios. It is expected that as older wideband radios are removed from service that this issue will be resolved. Most radios in use will be narrowband eliminating this issue. This information is current at time of printing. For further up to date information please visit www.acma.gov.au

Important information.....................................................7 Installation of your Oricom Radio ..................................8 Operations ...................................................................11 UHF CB channels and frequencies .............................27 Express Warranty (Australia).......................................31 Table of contents Need Help? If you need assistance setting up or using your Oricom product now or in the future, call Oricom Support. Australia 1300 889 785 or (02) 4574 8888 www.oricom.com.au Mon-Fri 8am – 6pm AEST New Zealand 0800 67 42 66 www.oricom.co.nz Mon-Fri 10am – 8pm NZST

Controls and Indicators Front View of Controller Speaker Microphone 1 2 3 4 5 6 7 8 9 1. LCD display 2. Microphone 3. On/Off/Volume/Channel/ Squelch 4. Speaker 5. Scan/Memory skip/ Memory 1 6. Priority channel recall/Key lock/Memory 2 7. Monitor/Tone Squelch/ Memory 3 8. Triple watch/Menu/ Memory 4 9. Memory recall/Memory write

Rear view of Radio 3 2 1 1. 3.5mm external jack for optional 8 ohm speaker 2. Power supply connection 3. Antenna Jack

LCD Icons & Indicators 1 2 3 4 5   9 7 8 6 1. Signal strength & TX meter 2. Triple watch on 3. Duplex on 4. Status display 5. Channel display 6. CTCSS or DCS channel display 7. Scrambler on 8. DCS on 9. CTCSS on 10. Roger Beep on 11. Memory channel

Oricom radio The operation of your UHF radio in Australia and New Zealand is subject to conditions in the following licenses: In Australia, the ACMA Radio communications (Citizen Band Radio Stations) and in New Zealand by MED the General User Radio License for Citizen Band Radio. Safety Information and Warnings WARNING Potentially Explosive Atmosphere Turn your radio OFF when in any area with a potentially explosive atmosphere. Sparks in such areas could cause an explosion or fire resulting in injury or even death. NOTE: Areas with potentially explosive atmospheres are often, but not always clearly marked. They include fuelling areas such as below deck on boats; fuel or chemical transfer or storage facilities; areas where the air contains chemicals or particles, such as grain, dust, or metal powders; and any other area where you would normally be advised to turn off your vehicle engine. Blasting Caps and Areas To avoid possible interference with blasting operations, turn your radio OFF near electrical blasting caps or in a “blasting area” or in areas posted: “Turn off two way radios.” Obey all signs and instructions. Electromagnetic Interference/Compatibility Nearly every electronic device is susceptible to electromagnetic interference (EMI). To avoid the possibility of electromagnetic interference and/or compatibility conflicts, turn off your radio in any location where posted notices instruct you to do so such as health care facilities.

The controller speaker microphone uses a 6-pin telephone style plug and socket: 1. Position the microphone plug so the plastic flap faces downwards, and insert the plug into the socket until it ‘clicks’. 2. Gently press the rubber boot into the hole surrounding the socket so that the slot around the boot fits neatly inside the rim of the entry hole. Disconnecting the Controller Speaker Microphone It is recommended that the Controller Speaker Microphone be left permanently connected to the radio, but if it must be disconnected, proceed as follows: 1. Lift the rubber boot and the lip of the raised area on the front panel. 2. Ease the rubber boot out of the cable entry hole and slide it along the cable away from the front panel. 3. Identify the plug locking lever, and move the lever towards the plug body. At the same time gently pull the plug from the socket. Installation of your Oricom Radio

CAuTION When installing your radio in your vehicle, check that during installation you do not damage any wiring or vehicle components that may be hidden around the mounting position. Ensure the installation does not interfere with the operation of the vehicle and meets all regulatory and safety retirements for accessories fitted to your vehicle. For optimum performance, your radio needs to be installed correctly. If you are unsure about how to install your radio, we suggest you have your radio professionally installed by a UHF specialist or Auto electrician. When installing the radio, avoid mounting it close to heaters or air conditioners. Never press the PTT button before connecting the antenna to the radio. Wiring Methods There are two possible wiring configurations for connecting to the vehicles power supply. A. Radio stays ON when the ignition is switched OFF Connect the radio’s negative (black) lead to the vehicle chassis, or directly to the battery’s negative terminal. Connect the radio’s positive (red) lead via the 3 Amp fuse to the battery’s positive terminal. Alternatively, the positive lead could be connected at the fuse box at a point that has DC Power continuously available (preferably the battery side of the ignition switch) via the 3 Amp fuse. B. Radio turns OFF with the ignition switch Connect the radio’s negative (black) lead to the vehicle’s chassis, or directly to the battery’s negative terminal. The radios positive (red) lead should connect to an accessory point in the vehicle’s fuse box via the 3 Amp fuse.

Antenna information The antenna (not supplied) is of critical importance to maximise your output power and receiver sensitivity. A poorly installed, inferior quality antenna, or one not designed for the correct frequency band, will give poor performance. You should only purchase an antenna designed for the 477MHz frequency band. Antenna installation 1. Connect the antenna to the rear antenna socket using a PL259 coaxial connector (not supplied). 2. To obtain maximum performance from the radio, select a high quality antenna and mount it in a good location. Never press the PTT before connecting the antenna to the radio. Optional accessories If required, you may install an external (8 ohm, Minimum 5W power) speaker fitted with a 3.5mm plug (not supplied). Depending on the installation, it may be necessary to use an external speaker (not supplied) to give improved volume and clarity. This can be plugged into the external speaker (SP) socket on the rear of the unit.

Press and hold the Channel selector. At power on, the current applied DC voltage is displayed numerically as shown below. Special over and under voltage detection circuitry protects the radio and warns of excessive voltage conditions by the LCD flashing the 3 backlight colours. Setting the Volume Turn the channel selector clockwise to adjust the sound level for comfortable reception. Operations

Press channel selector once. “CH” will appear on the LCD. Select the channel by rotating the channel knob. Setting the Squelch Level 1. Press channel selector 2 times. The current squelch level is displayed. 2. Select the squelch level by rotating the channel knob. The radio has 16 preset (off to 15) squelch levels, off-Squelch open. 1 - Max. sensitivity (Min. squelch) 15 - Min. sensitivity (Max/Tight squelch) Note : * If a button is not pressed within 5 seconds, the radio will automatically exit the sub display of “VOL” “CH” and “SQL”.

Pressing the PTT allows audio to be transmitted, by speaking across the front of the controller speaker microphone. TX is indicated by the level bars on the LCD display. To receive, release the PTT button and then TX will disappear on the display. When transmitting, hold the MIC 5 cm from your mouth and speak clearly in normal voice across the front of the mic. Scanning The Scan feature allows you to search for active channels automatically. There are two scanning modes: Open Scan and Priority Scan. Both of these scan modes can be set from the menu. Open scan Press Scan/Menu button and scanning starts. The OS sub menu display appears on the LCD. The scan direction can be changed at any time by rotating the channel selector left or right. To stop Scan, press Scan/Menu Button or PTT button. When a signal is found, scanning will stop at that channel to allow the signal to be heard, then resume scanning when the channel is clear again. CH 1-2-3-4-5-6-7 …… 77-78-79-80 Press

inserts your Priority Channel into the scan sequence. This means that your Priority Channel will be monitored regularly while scanning to ensure that no calls are missed. Any signal received on your Priority Channel will take precedence over any signals received on the other channels. CH 1-2-3-4-5- PRI CH - 6-7-8-9-10- PRI CH …… 76-77-78-79-80 Memory On/Off Your UHF390 has been pre-programmed with all the UHF CB channels into the Open Scan channel memory. However, you can change or customize the channels by this function. • Select the desired channel with rotary knob. • Press and hold SC/MEM button. • The memory icon “M” disappears. Priority channel Recall You can store a priority channel through the menu in the “PRI” setting. To recall the priority channel press the PRI/LOC button. “PRI” will appear along with the priority channel number. This priority channel will also be automatically monitored during Priority Scan. Key Lock To prevent accidental entries, you can lock the key pad. To enable “Key lock” Function: Press and hold Press Operations

When the key lock is active, a warning beep will be heard if you attempt to press keys. Note: The PTT, volume / channel / squelch dial do not lock. Warning beep is only active if beep function is turned on. • To disable the Key lock function: • Press hold “PRI/LOC” button. “LOC OF” will then appear. Monitor Function The monitor button is used to temporarily open the squelch, in order to listen to signals that are too weak to keep the squelch permanently opened. For brief listening, press Monitor briefly to turn Squelch off, press briefly again to turn Squelch back on. Selecting the Required CTCSS or DCS Tone To pre-select the CTCSS tone or DCS on your radio, please refer to the MENU setting. Enabling CTCSS or DCS on a Channel If a CTCSS tone has been selected, it can be enabled on individual channels. 1. Rotate the Channel knob to select the required channel. The letters CT or DT icon will appear. 2. Press and hold the MO/TSQ button. Disabling CTCSS or DCS on a Channel Repeat steps 1 and 2 above. Press and hold Press Press and hold Operations

Pressing the TW/MENU button activates the Triple watch function. The Triple Watch feature allows for monitoring of 2 or 3 channels. The currently displayed channel and 2 more channels saved in TRI1 and TRI2. To store the channels in TRI1 or TRI2, select the channels and features CTCSS/DCS/Duplex on the display, then enter menu mode and save the channel in TRI1 or TRI2. If only one additional channel is required, then select “Off” in TRI2. Once Watch is activated, by pressing the TW/MENU button, the TRI 1 and TRI 2 channels are checked in the following sequence: Main channel is checked for 0.7 of a second, then TRI 1 for 0.15 seconds, TRI 2 FOR 0.15 seconds and then back to the Main channel. The sequence is repeated until a signal is detected or radio is switched off. If there is a signal present on TRI 1 or TRI 2, the radio will wait on that channel for 5 seconds after the signal is no longer present, then revert to Tri Watch operation. Triple Watch can be disabled by pressing any keys. Memory recall channels To access memorized channels simply press the “MR/MW” button then one of the M1 to M4 buttons. Press The default channels of M1 to M4 M1 : 1 channel M2 : 20 channels M3 : 40 channels M4 : 80 channels Press Operations

The Memory write button is used to store a channel in the memory locations M1 to M4. To store channels: • Select the desired channel with rotary knob. • Press and hold MR/MW button. • Select the location you would like to store the channel by pressing M1, M2, M3 or M4. Memory scan • Press SC/MEM button to start scanning. • Whilst radio is in scan mode, push and hold the SC/MEM button for 2 seconds, the radio will now start scanning the stored channels in M1, M2, M3 and M4. • When you want to stop scanning, you can press the SC/MEM button or push the PTT button. Menu Function The Menu function provides a convenient method of customizing some of the radios functions. The following menu options are available: Note that some items are only available on certain channels. To access the Menu functions: 1. Press and hold the TW/MENU button. The first menu function is displayed. 2. Briefly press the menu button to cycle through each available function. After the last function has been selected, the cycle automatically exits the menu. 3. Use the volume control to change the parameters of the selected function. Press and hold Operations

button for 2 seconds. The following features can be selected by using the “MENU” button: 1) User selectable 38 CTCSS and 104 DCS codes (CTCSS or DCS cannot be enabled on channels 5 or 35) 2) Scrambler setting (Off, 1 to 5 different frequencies) 3) LCD backlight colour (3 colours) 4) LCD backlight level (Bright or Dim) 5) Voice enhancer equalizer setting (-5 to +5, 10 steps) 6) Duplex On/Off 7) Priority channel memory ( 1 to 80 Channel) 8) Scan mode (Open or priority scan) 9) Busy channel lockout (On or Off) 10) Key beep tone (On or Off) 11) Roger beep tone (On or Off) 12) Triple watch sub channel 1 setting 13) Triple watch sub channel 2 setting 14) Squelch tail (On or Off) 15) Auto power off 1 ,2 or 4 hours 16) Software version display Operations

CTCSS 38 CTCSS 01 DCS 104 Scrambler 1 Off Off 5 Backlight LED colour YE Green Green Ab Bright of LCD br Bright dr Voice equalizer +5 0 0 -5 Duplex On Off Off Priority CH. 1 11 11 80 Scan mode OS OS PS Busy channel lock On Off Off Key beep tone On Off Off Roger beep tone On Off Off Operations

1 Off 80 Triple watch CH 2 1 Off 80 Squelch tail On Off Off Auto power off Off Off 1 2 4 Software Version Ver. 01 Version Duplex General Your radio has a Repeater Access function to allow use of local repeater station (if available in your area). Repeaters are shared radio systems installed by interested parties (clubs, local business etc.) that pick transmissions on specific channels and re-transmit (or repeat) the received signal to another channel. Channel 2 Channel 32 Channel 2 Channel 32 Repeater Station

and 41 to 48) used by local repeater stations. When activated, your radio will receive the Repeater on its specific channel (all repeater outputs are on channel 1 to 8 and 41 to 48) but transmit to the repeater channel 31 to 38 and 71 to 78 (Factory default is set to On for all repeater channels). e.g. CH01 on Duplex mode will receive on CH01 but transmit on CH31. CH02 on duplex mode will receive on CH02 but transmit on CH32. If you transmit on CH01 duplex mode, you are actually transmitting on CH31; the repeater station down converts your signal and retransmits on CH01. Your transceiver allows you to pre-select Duplex operation individually on each channel. CH and Number Simplex mode Transmit/ Receiver Frequency (MHz) Duplex Mode Transmit/ Receiver Frequency(MHz) 1 476.425 477.175 CH31 2 476.450 477.200 CH32 3 476.475 477.225 CH33 4 476.500 477.250 CH34 5 476.525 477.275 CH35 6 476.550 477.300 CH36 7 476.575 477.325 CH37 8 476.600 477.350 CH38 41 476.4375 477.1875 CH71 42 476.4625 477.2125 CH72 43 476.4875 477.2375 CH73 44 476.5125 477.2625 CH74 45 467.5375 477.2875 CH75 46 476.5625 477.3125 CH76 47 476.5875 477.3375 CH77 48 476.6125 477.3625 CH78

channel. CTCSS and DCS Setting This feature allows you to receive signals only from callers who have selected the same CTCSS and DCS code. DCS is similar to CTCSS. It provides 104 extra, digitally coded, squelch codes that follow after the 38 CTCSS codes. CTCSS 1 - 38, followed by DCS 1 - 104. Scramble Scramble enables private communications by scrambling the voice signal. This prevents users without descrambler equipment or a compatible unit from understanding the conversation. Select desired channel. SCR appears when scramble is turned on in the menu. You can select 1 to 5. 3 Multi Colour backlight You can select from 3 different colours for the LCD backlight. LCD Backlight Brightness You can reduce the brightness of the LCD backlight to be more comfortable while driving at night. Operations

Choose from 10 different receive audio level settings to provide a natural voice enhancer for super clarity and performance. The radio has 10 preset (-5 to 5) voice enhancer equalizer levels. -5 : Bass - Enhancing the low frequencies, the sound quality becomes mild and easy to listening. 0 : Normal. +5 : Treble - Enhancing the high frequencies, the sound quality becomes sharp. -5 : Bass 0 : Normal +5 : Treble Duplex Duplex mode can be turned on or off on the duplex channels. When turned on, the transmit channel will be as shown in the table on page 21. Priority Channel Set A priority channel can be stored in the menu. The letter “PRI” will appear when the selected channel is set to Priority. This channel will then be automatically monitored during the Priority Scan. Note: You can only store one channel as your priority channel. Operations

Priority scanning (PS). Scanning allows you to search for active channels programmed in the memory. You can choose Scan type in menu mode. To initiate scanning: Press scan key and scanning starts. OS icon appears during scanning. Open Scan (OS) Mode The Open Scan feature scans for activity on all CB channels in memory. Once a channel is located, scanning will pause. This will allow the signal to be heard. Open Scan Priority Scan (PS) Mode With Priority Scan, the radio scans for activity, but in addition, it also inserts your Priority Channel into the scan sequence. This means that your Priority Channel will be monitored regularly while scanning to ensure that no calls are missed. Any signal received on your Priority Channel will take precedence over any signals received on the other channels. The priority channel will be checked after every 4th channel scanned. ...... PRIORITY SCAN

If the channel is already in use, you can prevent the UHF CB radio from transmitting. This is particularly important when using CTCSS/DCS. Key Beep The Beep tone emits a tone when you press any of the buttons on the controller speaker microphone (except PTT button). Roger Beep This function emits a beep on the communication party to inform that the transmission is finished. Squelch Tail Squelch tail is the noise heard after the transmitting party releases the PTT and is heard by the receiving party. If Squelch Tail is turned ON, on both radios this squelch noise will be muted. Auto Power Off This feature allows the radio to be connected directly to the battery of a vehicle and when enabled, will automatically turn the radio off, if it has not been used for a preset period of time 1, 2 or 4 hours. The main purpose of this feature is if the radio is inadvertently left on when directly connected to the battery it automatically turns the radio off to prevent the battery from being discharged.

need to reset your UHF radio. Caution: This procedure clears all the information you have stored in your UHF radio. Before you reset your UHF radio, try turning it off and on again. If your UHF radio is still not functioning correctly, you may need to reset the UHF radio. To reset, press and hold monitor button and power on. “Reset” will appear in the display. The radio will then return to standby mode. TOT (Time Of Timer) Australian and New Zealand standards require that if the PTT is pressed for more than 3 minutes, the unit must stop transmitting. The radio is set to stop transmitting after 2 minutes and 30 seconds of continuous transmission. “TOT-on” will appear in the display and it will emit a beep sound to indicate that TOP is activated.

Channel Frequency Table Radiocommunications (Citizen Band Radio Stations) Class Licence 2002 No licence is required to own or operate this radio in Australia and New Zealand. The Radiocommunications (Citizen Band Radio Stations) Class Licence 2002 contains the technical parameters, operating requirements, conditions of licence and relevant standards for Citizen Band (CB) radios. CB radios must comply with the class licence for their use to be authorised under the class licence. UHF channels and frequencies IMPORTANT NOTE: The operation of your uHF radio in Australia and New Zealand is subject to conditions in the following licenses: In Australia the ACMA Radio communications (Citizen Band Radio Stations) and in New Zealand by MED the General user Radio License for Citizen Band Radio. EMC Technologies (NZ) Ltd Test Report No 101127.1 Report date: 25th November 2010 6.2 Nominal Carrier Table 1 Nominal Carrier Frequency Channel Tx Rx Channel Tx Rx Freq Freq Freq Freq MHZ MHz MHz MHz 01* 476.4250 476.4250 21 476.9250 476.9250 41* - 476.4375 61‡ — — 02* 476.4500 476.4500 22† 476.9500 476.9500 42* - 476.4625 62‡ — — 03* 476.4750 476.4750 23† 476.9750 476.9750 43* - 476.4875 63‡ — — 04* 476.5000 476.5000 24 477.0000 477.0000 44* - 476.5125 64 477.0125 477.0125 05* 476.5250 476.5250 25 477.0250 477.0250 45* - 476.5375 65 477.0375 477.0375 06* 476.5500 476.5500 26 477.0500 477.0500 46* - 476.5625 66 477.0625 477.0625 07* 476.5750 476.5750 27 477.0750 477.0750 47* - 476.5875 67 477.0875 477.0875 08* 476.6000 476.6000 28 477.1000 477.1000 48* - 476.6125 68 477.1125 477.1125 9 476.6250 476.6250 29 477.1250 477.1250 49 476.6375 476.6375 69 477.1375 477.1375 10 476.6500 476.6500 30 477.1500 477.1500 50 476.6625 476.6625 70 477.1625 477.1625 11 476.6750 476.6750 31* 477.1750 477.1750 51 476.6875 476.6875 71* 477.1875 - 12 476.7000 476.7000 32* 477.2000 477.2000 52 476.7125 476.7125 72* 477.2125 - 13 476.7250 476.7250 33* 477.2250 477.2250 53 476.7375 476.7375 73* 477.2375 - 14 476.7500 476.7500 34* 477.2500 477.2500 4 4 6 62 4 6 62 4* 4 262

48* - 476.6125 68 477.1125 477.1125 9 476.6250 476.6250 29 477.1250 477.1250 49 476.6375 476.6375 69 477.1375 477.1375 10 476.6500 476.6500 30 477.1500 477.1500 50 476.6625 476.6625 70 477.1625 477.1625 11 476.6750 476.6750 31* 477.1750 477.1750 51 476.6875 476.6875 71* 477.1875 - 12 476.7000 476.7000 32* 477.2000 477.2000 52 476.7125 476.7125 72* 477.2125 - 13 476.7250 476.7250 33* 477.2250 477.2250 53 476.7375 476.7375 73* 477.2375 - 14 476.7500 476.7500 34* 477.2500 477.2500 54 476.7625 476.7625 74* 477.2625 - 15 476.7750 476.7750 35* 477.2750 477.2750 55 476.7875 476.7875 75* 477.2875 - 16 476.8000 476.8000 36* 477.3000 477.3000 56 476.8125 476.8125 76* 477.3125 - 17 476.8250 476.8250 37* 477.3250 477.3250 57 476.8375 476.8375 77* 477.3375 - 18 476.8500 476.8500 38* 477.3500 477.3500 58 476.8625 476.8625 78* 477.3625 - 19 476.8750 476.8750 39 477.3750 477.3750 59 476.8875 476.8875 79 477.3875 477.3875 20 476.9000 476.9000 40 477.4000 477.4000 60 476.9125 476.9125 80 477.4125 477.4125 * The primary use for these channels is repeater operation using 750 kHz offset. Channels 1-8 inclusive are used for mobile reception and channels 31-38 for mobile transmission. They may also _____________________________________________________________________________________________________________________________________________________ EMC Technologies (NZ) Ltd STREET ADDRESS - 47 MacKelvie Street, Grey Lynn, Auckland, NZ Phone: +64 9 360 0862 Fax: +64 9 360 0861 POSTAL ADDRESS - PO Box 68 307, Newton, Auckland, New Zealand E-mail: [email protected] Page 11 of 23 This report may not be reproduced except in full * The primary use for these channels is repeater operation using 750 kHz offset. Channels 1-8 and 41-48 inclusive are used for mobile reception and channels 31-38 and 71-78 for mobile transmission. In addition, any designated repeater channel may be used for simplex operation in areas where it is not used for repeater operation. † Speech telephony is prohibited on these channels. ‡ At the time of production Channels 61, 62 and 63 are guard channels and are not available for use. Channel 5 and 35 (paired for Duplex repeaters) are reserved as emergency channels and should be used only in an emergency. CTCSS and DCS will not operate on channels 5 and 35. A list of currently authorised channels can be obtained from the ACMA website in Australia and the MED website in New Zealand. Channel 11 is a calling channel generally used to call others and channel 40 is the customary road vehicle channel. Once contact is established on the calling channel, both stations should move to another unused "SIMPLEX" channel to allow others to use the calling channel. Channels 22 and 23 are for Telemetry and Telecommand use, voice communications are not allowed on these channels. Channel 9 and above are the best choices for general use in Simplex mode.

38 CTCSS CODE LIST CODE Frequency(Hz) CODE Frequency(Hz) OFF OFF 20 131.8 1 67.0 21 136.5 2 71.9 22 141.3 3 74.4 23 146.2 4 77.0 24 151.4 5 79.7 25 156.7 6 82.5 26 162.2 7 85.4 27 167.9 8 88.5 28 173.8 9 91.5 29 179.9 10 94.8 30 186.2 11 97.4 31 192.8 12 100.0 32 203.5 13 103.5 33 210.7 14 107.2 34 218.1 15 110.9 35 225.7 16 114.8 36 233.6 17 118.8 37 241.8 18 123.0 38 250.3 19 127.3

Code No. DCS Code (Octal) Code No. DCS Code (Octal) Code No. DCS Code (Octal) 1 023 36 223 71 445 2 025 37 225 72 446 3 026 38 226 73 452 4 031 39 243 74 454 5 032 40 244 75 455 6 036 41 245 76 462 7 043 42 246 77 464 8 047 43 251 78 465 9 051 44 252 79 466 10 053 45 255 80 503 11 054 46 261 81 506 12 065 47 263 82 516 13 071 48 265 83 523 14 072 49 266 84 526 15 073 50 271 85 532 16 074 51 274 86 546 17 114 52 306 87 565 18 115 53 311 88 606 19 116 54 315 89 612 20 122 55 325 90 624 21 125 56 331 91 627 22 131 57 332 92 631 23 132 58 343 93 632 24 134 59 346 94 654 25 143 60 351 95 662 26 145 61 356 96 664 27 152 62 364 97 703 28 155 63 365 98 712 29 156 64 371 99 723 30 162 65 411 100 (A0) 731 31 165 66 412 101 (A1) 732 32 172 67 413 102 (A2) 734 33 174 68 423 103 (A3) 743 34 205 69 431 104 (A4) 754 35 212 70 432 UHF CB channels and frequencies

Express Warranty (Australia) This Express Warranty is provided by Oricom International Pty Ltd ABN 46 086 116 369, unit 1, 4 Sovereign Place, South Windsor NSW 2756, herein after referred to as “Oricom”. Oricom products come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. Oricom warrants that the product is free from defects in materials or workmanship during the Express Warranty Period. This Express Warranty does not extend to any product from which the serial number has been removed or was purchased outside of Australia. Nothing in this Express Warranty excludes, restricts or modifies any condition, warranty, guarantee, implied term, right or remedy pursuant to the Australian Consumer Law and which may not be so excluded, restricted or modified. For such conditions, terms, guarantees and warranties that cannot be excluded, restricted or modified, Oricom limits the remedies available to extent permitted in the relevant legislation. The Express Warranty Period will be 5 years from the date of purchase of the product evidenced by your dated sales receipt. You are required to provide proof of purchase as a condition of receiving Express Warranty services. You are entitled to a replacement product or repair of the product at our discretion according to the terms and conditions of this document if your product is found to be faulty within the Express Warranty Period. This Express Warranty extends to the original purchaser only and is not transferable. Products distributed by Oricom are manufactured using new materials or new and used materials equivalent to new in performance and reliability. Spare parts may be new or equivalent to new. Spare parts are warranted to be free from defects in material or workmanship for thirty (30) days or for the remainder of the Express Warranty Period of the Oricom branded product in which they are installed, whichever is longer. During the Express Warranty Period, Oricom will where possible repair and if not replace the faulty product or part thereof. All component

unlikely event that your Oricom product has a recurring failure, Oricom may always, subject to the Competition and Consumer Act 2010, at its discretion, elect to provide you with a replacement product of its choosing that is at least equivalent to your product in performance. No change to the conditions of this Express Warranty is valid unless it is made in writing and signed by an authorised representative of Oricom. Oricom will not be liable under this Express Warranty, and to the extent permitted by law will not be liable for any defect, loss, damage or injury arising out of or in connection with a: 1. Failure by you to adhere to the warnings and follow the instructions set out in this user guide for the proper installation and use of the product; 2. Wilful misconduct or deliberate misuse by you of the product; 3. Any external cause beyond our control, including but not limited to power failure, lightning or over voltage; or 4. Modification to the product or services carried out on the product by anyone other than Oricom or Oricom’s authorised service provider. Express Warranty (Australia)

Oricom has a simple warranty process for you to follow: •� �Please�call�or�email�our�Customer�Support�Team,�1300�889�785�or� [email protected]. •� �A�Customer�Support�Team�member�will�verify�after�troubleshooting�with�you�if� your product qualifies under warranty. If so, they will give you a Product Return Authorisation number. •� �We�will�then�email�or�fax�a�Return�Authorisation�form�and�a�Repair�Notice�(if� necessary), together with instructions on how to return the goods for warranty service. Please note that if a Customer Support Team member advises that your product does not qualify for return, this warranty does not apply to your product. Products that are authorised to be returned to Oricom in Australia must include all of the following: •� A�completed�Return�Authorisation�form •� �A�copy�of�your�Proof�of�Purchase�(please�keep�your�original�copy) •� The�faulty�product,�including�all�accessories. Send the approved returns to: Oricom International Pty Ltd Locked Bag 658 South Windsor NSW 2756 Australia Please note that this Express Warranty excludes expenses incurred by you in returning any faulty product to us. You must arrange and pay any expenses incurred (including postage, delivery, freight, transportation or insurance of the product) to return the faulty product to us, however, we will arrange delivery of the repaired or replaced faulty product to you. Express Warranty (Australia)

generated data (such as stored telephone numbers, text messages and contact information). Please ensure that you have made a copy of any data saved on your goods before sending for repair. Please also be aware that goods presented for repair may be replaced by refurbished goods or parts of the same type rather than being repaired. Express Warranty (Australia)

Oricom have a trained and dedicated team of Customer Support Representatives, each with the knowledge and resources to assist in answering your questions quickly and efficiently. Oricom Support - Australia For all product enquiries, troubleshooting or to discuss the range of Oricom products, feel free to contact Oricom or visit our website for answers to frequently asked questions. 1300 889 785 Monday - Friday 8am – 6pm AEST Email: [email protected] www.oricom.com.au Oricom Support - New Zealand 0800 674 266 Monday - Friday 10am - 8pm NZST Email: [email protected] www.oricom.co.nz Ref: 03082018