Reliable 7000FE Instruction Manual

the 7000FE end cutting system from Reliable. Everything you need to start end cutting is included. A heavy-duty 4” cutting head with a manual sharpener, 96” track with lifter set and uprights with a piece goods bar for your fabric. For your safety and to fully enjoy the advantages of this product, please take a few minutes to read all of the important safeguards and care instructions. Keep this manual handy for your reference.

hand on the same side of operation when the machine is installed. 1. SETTING UP THE FABRIC ROLL STAND (CB-13) A) Fix the stands on both sides at the end of table and tie the drive. B) Lie down the fabric roll on the fabric stands. 2. SETTING UP THE CLAMPS (CB-02) A) Find and fix two clamps on both sides of the table and tie the drive. B) Find and fix the twin spring on the clamp of the operated side (single spring set up on another clamp). C) Attach the spring connector (CB-17) on the bar lifter stands (CB-10). 3. SETTING UP THE BELT FOR THE BAR LIFTER (CB-25) A) Find the green plastic belt and fix one end into the belt connector (CB-08) clamp. B) Pull the other end of the belt across the plastic roller. 4. SET UP RAIL (CB-01) A) Lie down the rail on two clamps and secure with a bolt. 5. SETTING UP THE RAIL (CB-01) A) Take off the lift handle (CB-11A) and spring (CB-49). B) Insert the cutter plate into the rail and restore (CB-11A) and (CB-49). 6. CONNECTING THE POWER A) Find the electric cable and connect the socket (CE-04) with the plug (CE-03) and con- nect another cable end with the power source. B) Short handle: turn on operating switch (CE-05) for machine to start. C) Long handle: power will be started when the cutter head is pushed out from the operated side.

PLASTIC ROLLER ROLLER SHAFT SCREW FOR RAIL SCREW FOR LOFT HANDLE BELT CONNECTOR FOR BAR LIFTER BAR LIFTER STAND LIFT HANDLE (PLASTIC) LIFT HANDLE (ALUMINUM) FABRIC ROLL HOLDER STAND FOR FABRIC ROLL SCREW DRIVE FOR CLAMP SCREW DRIVE FOR FABRIC ROLL STAND NUT FOR CLAMPING SCREW SPRING CONNECTOR CB-18 CB-19 CB-22 CB-23 CB-24 CB-25 CB-26 CB-27 CB-28 CB-29 CB-30 CB-31 CB-42 CB-47 CB-49 CB-50 W-019BB(W) SQUARE SEAT ROLLER SEAT SPRING FABRIC ROLL HOLDING ROLLER STEEL PIECE BELT FOR BAR LIFTER RAIL RUBBER TAPE CLOTH PRESS TRACK BEARING FOR FABRIC ROLL HOLDER 626 BUSH BEARING LM-13 BUSH CLIP BOLT FOR BAR LIFTER ELBOW HOLDING ROLLER PLASTIC ARROW LIFT HANDLE SWITCH SET SPRING C. TYPE SPRING MOTOR(220V)G MOTOR ASSEMBLY & ACCESSORIES

CA-01(W) CA-01A CA-01B CA-01C CA-02 CA-03 CA-04 CA-04A CA-04C CA-04E CA-05 CA-06A-1 CA-07A CA07B CA-09 CA-10 CA-11A CA-11(W) CA-12 CA-13 CA-14 CA-15 MOTOR COVER (WHITE) CARBON BRUSH CARBON BRUSH COVER CARBON BRUSH HOLDER TERMINAL BOX COVER FOR TERMINAL BOX SHORT HANDLE LONG DRIVE HANDLE CONNECT FOR LONG HANDLE SCREW FOR LONG HANDLE CONNECTOR MOTOR PLATE MOTOR STAND LOWER BLADE ARM LOWER BLADE ARM ADJ COLLAR FOR KNIFE LOCK NUT FOR KNIFE SCREW FOR BLANCE IRON BLANCE IRON (WHITE) KNIFE COVER KNIFE GUARD MOTOR COVER PIECE SPRING FOR COLLAR CA-16 CA-17 CA-19 CD CD-01 CD-48-E CD-02 CD-03 CD-04 CD-05 CD-06 CD-07 CE-01 CE-01C CE-02BB CE-03 CE-04 CE-04A CE-05 CE-05-01 CE-06 ROUND KNIFE LOWER BLADE SWITCH PLATE GRINDER ASSEMBLY GRINDER STONE SWITCH CABLE (GLORY) BEARING BRAZE SET FOR BEARING PLATE FOR GRINDER STONE SPRING PUSH BUSH GRINDER SUPPORT MOTOR AXIS MOTOR COIL COUNTER (220V) CABLE PLUG SOCKET CABLE OPERATING SWITCH LONG DRIVE HANDLE OPERATING SWITCH COUNTER SWITCH

every product sold by Reliable (a “Reliable Product”) is free from defects in material and workmanship for a period of one year from the date of purchase if properly used and maintained. Subject to the conditions and limitations set forth below, Reliable will either repair or replace any part of a Reliable Product that proves defective by reason of improper workmanship or materials. If the defective Reliable Product is no longer available and cannot be repaired effectively or replaced with an identical model, Reliable shall replace the defective Reliable Product with a current Reliable Product of equal or greater value. Repaired parts or replacement products will be provided by Reliable on an exchange basis, and will be either new or refurbished to be functionally equivalent to new. If Reliable is unable to repair or replace a Reliable Product, it will refund the current value of that Reliable Product at the time the warranty claim is made. This limited warranty does not cover any damage to a Reliable Product that results from improper installation, accident, abuse, misuse, natural disaster, insufficient or excessive electrical supply, abnormal mechanical or environmental conditions, wear and tear resulting from normal use of the product, or any unauthorized disassembly, repair, or modification. This limited warranty does not extend to any indirect, consequential or incidental damages that may be suffered by a user or from the use of a Reliable Product, including without limitation, any liability for third party claims for damage, and is limited to the amount paid by the original purchaser Reliable Product with respect to which this limited warranty protection applies. This limited warranty does not apply with respect to products that have been altered or which are missing serial numbers or for products not purchased directly from Reliable or a dealer authorized by us to sell Reliable Products. This limited warranty is the only warranty that applies to any Reliable Product, supersedes any and all terms that may be contained in any other document or purchase order and may not be altered or amended except expressly in writing by Reliable. To obtain a repair or replacement under the terms of this warranty, please contact our customer service group at 1-800-268-1649 or at [email protected]. You will be required to submit an original receipt via fax or e-mail. The receipt must reflect that you are the original purchaser, the product was bought directly from us or from an authorized Reliable dealer and that the warranty claim is being made within the warranty period. You will be issued a return authorization number (RA#) and asked to ship the defective product together with proof of purchase and RA#, prepaid insured to the following address: Reliable Corporation, 5-100 Wingold Avenue, Toronto, ON M6B 4K7. Freight collect shipments will be refused. The risk of loss or damage in transit will be borne by the customer. Once Reliable receives the defective product, it will initiate the repair or replacement process. If you have any questions regarding this warranty, you may write to: Reliable Corporation 100 Wingold Avenue, Unit 5 Toronto, Ontario Canada M6B 4K7 www.reliablecorporation.com RELIABLE PRODUCTS WARRANTY