Texas Instruments TMS320C6472 Quick Setup Manual

(with integrated XDS560v2 Emulator) Quick Setup Guide TMDSEVM6472LE Getting Started: The ships with a Power On self Test (POST) flashed in to I2C EEPROM. The POST will be automatically executed when the board is powered ON. POST will perform memory test and internal EMAC loopback test. At 'power on' the user LEDs will be OFF by default. The LEDs will blink and turn OFF to indicate successful DSP booting. Then after, User LED-1 will turn ON to indicate successful RAM test and User LED-2 will turn ON to indicate successful internal EMAC loop-back test. These LEDs will remain ON to indicate success of both the tests. Please refer MCSDK Getting Started Guide and MCSDK User Guide for software installation and other details. Helpful Hints: • Plug in all the cables before turning the EVM ON to ensure proper grounding. • Do not unnecessarily flex the boards, while inserting cables. Excessive flexing can break the PCB traces. Online Documentation Most of the information on TMDSEVM6472LE is available online. Some of the most commonly used resources are mentioned below: TMDSEVM6472LE Information: http://www.einfochips.com/TI-TMS320C6472-EVM.php This link contains: • Hardware & software details • Technical Reference Manual • TMS320C6472 Datasheet • Frequently Asked Questions (FAQ) C6472 DSP Information: http://focus.ti.com/docs/prod/folders/print/tms320c6472.html EVM6472 Support: Please write to for technical queries related to this EVM. eInfochips Address: eInfochips Limited 303 Parishram Building, 5/B Rashmi Society, Mithakhali Six Road, Navarangpura, Ahmedabad - 380009 Gujarat, INDIA. Tel: +91-79-2656 3705 Fax: +91-79-2656 0722 TMDSEVM6472LE [email protected] TI Worldwide Technical Support Internet TI Semiconductor Product Information Center Home Page support.ti.com TI Semiconductor KnowledgeBase Home page support.ti.com/sc/knowledgebase Product Information Centers Americas Phone +1(972) 644-5580 Fax +1(972)927-6377 Internet/Email support.ti.com/sc/pic/americas.htm Europe, Middle East and Africa Phone European Free Call 00800-ASK-TEXAS (00800 275 83927) International +49 (0) 8161 80 2121 Russian Support +7 495 981 0701 Note: The European Free Call (Toll Free) number is not active in all countries. If you have technical difficulty calling the free call number, please use the international number above. Fax +(49) (0) 8161 80 2045 Internet support.ti.com/sc/pic/euro.htm Japan Fax International +81-3-3344-5317 Domestic 0120-81-0036 Internet/Email International support.ti.com/sc/pic/japan.htm Domestic www.tij.co.jp/pic Asia Phone International Domestic Toll-Free-Number Toll-Free-Number Australia Malaysia China New Zealand Hong Kong Philippines India Singapore Indonesia Taiwan Korea Thailand Fax Email [email protected] [email protected] Internet support.ti.com/sc/pic/asia.htm Important Notice: The products and services of Texas Instruments Incorporated and its subsidiaries described herein are sold subject to TI's standard terms and conditions of sale. Customers are advised to obtain the most current and complete information about TI products and services before placing orders. TI assumes no liability for applications assistance, customer's applications or product designs, software performance, or infringement of patents. The publication of information regarding any other company's products or services does not constitute TI's approval, warranty or endorsement thereof. The floating bar is a trademark of Texas Instruments. All other trademarks are the property of their respective owners ©2011 Texas Instruments Incorporated eInfochips Literature: EVM6472E_QSG_1.0 +91-80-413816651- 800-999-084 800-820-8682 800-96-5941 1-800-425-7888 001-803-8861-1006 080-551-2804 +886-2-2378-6808 1-800-80-3973 0800-446-934 1-800-765-7404 800-886-1028 0800-006800 001-800-886-0010 w w w . e i n f o c h i p s . c o m +12V DC AMC- Type B+ C6472 DSP HPI - DC LEDs-I2C (*Note: Beneath the emulator) DDR2 RAM 256 MB FPGA JTAG User Switches Boot Mode/Configuration Settings UART Route Select 3-pin Rs232 serial USB UART XDS560v2 USB JTAG User LEDs* Blue LED* LED1* Warm Reset* Cold Reset* Dual Gigabit Ethernet Jack XDS560v2 Mezzanine Emulator NAND Flash 128 MB*, FPGA*, MSP430 (MMC)*

TMS320C6472 Evaluation Module with integrated XDS560v2 Emulator Power supply and power cord USB Cable for JTAG emulation Ethernet cable 3-Pin to 9-Pin DTE UART cable Software (DVD) and documentation ©2011 Texas Instruments Incorporated eInfochips Literature: EVM6472E_QSG_1.0 ©2011 Texas Instruments Incorporated eInfochips Literature: EVM6472E_QSG_1.0 C6472 Evaluation Module 3 Connect Ethernet switch / router / PC to the lower Gigabit Ethernet port (J3) of TMDSEVM6472LE board using an Ethernet cable to access EMAC0. Connect the Mini-USB cable to J1 plug on XDS560v2 Emulator for high speed emulation, as shown in figure. (For use with CCS debugger only) 2 1a The TMDSEVM6472LE is also shipped with an Out-Of-Box Demo application flashed into NAND. This is a network based application which starts an HTTP server and a TELNET server with the static IP address 192.168.2.100. Be sure the first switch in the dual-switch SW3 is off. In order to connect to the board, the test PC should be configured with a compatible static IP address such as 192.168.2.101. Once the User LEDs blink and turn OFF (indicating successful NAND boot) the user can access the following URL through a browser to view the Out-Of- Box demo: http://192.168.2.100 Ensure EVM configuration switches are set as shown to run 1Power On Self Test (POST). 1a To run demo through NAND, configure the switches as shown above. Out-Of-Box Connect the 12V DC power adapter (supplied with the kit) to power jack (J6). 4