Siemens 3wl Function Manual
Read Online
Read the Siemens 3wl Function Manual online using the built-in PDF viewer.
Text of the manual
Information about the library
2
Description of blocks
3
Configuration Manual
4
Technical specifications
5
Technical support
6
Library SENTRON 3WL / 3VL for
SIMATIC PCS 7
Function Manual
11/2008
A5E02316914A-01
V1.0
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken.
CAUTION
without a safety alert symbol, indicates that property damage can result if proper precautions are not taken.
NOTICE
indicates that an unintended result or situation can occur if the corresponding information is not taken into
account.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The device/system may only be set up and used in conjunction with this documentation. Commissioning and
operation of a device/system may only be performed by qualified personnel. Within the context of the safety notes
in this documentation qualified persons are defined as persons who are authorized to commission, ground and
label devices, systems and circuits in accordance with established safety practices and standards.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be adhered to. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of the Siemens AG. The remaining trademarks in this
publication may be trademarks whose use by third parties for their own purposes could violate the rights of the
owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
Siemens AG
Industry Sector
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E02316914A-01
Ⓟ 11/2008
Copyright © Siemens AG 2008.
Technical data subject to change
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
3
Table of contents
1
Introduction................................................................................................................................................ 7
1.1
General ..........................................................................................................................................7
1.2
Further documentation...................................................................................................................7
1.3
Installing the library........................................................................................................................7
1.4
Hardware configuration..................................................................................................................8
1.4.1
Incorporating via GSD file..............................................................................................................8
2
Information about the library .................................................................................................................... 13
2.1
Overview of the blocks.................................................................................................................13
2.2
General information about OS typicals........................................................................................13
2.2.1
Faceplates....................................................................................................................................13
2.2.2
Symbols .......................................................................................................................................15
3
Description of blocks................................................................................................................................ 17
3.1
Diagnostics block DIA_WLVL ......................................................................................................17
3.1.1
Calling OBs ..................................................................................................................................18
3.1.2
Called blocks................................................................................................................................18
3.1.3
Function .......................................................................................................................................18
3.1.4
Message behavior........................................................................................................................18
3.1.5
Error behavior ..............................................................................................................................19
3.1.6
I/O access error ...........................................................................................................................19
3.1.7
Module fault..................................................................................................................................19
3.1.8
Read diagnostics data of 3WL / 3VL ...........................................................................................19
3.1.9
Start-up characteristics ................................................................................................................20
3.1.10
Block parameters .........................................................................................................................20
3.2
Driver module DRV_3WL.............................................................................................................22
3.2.1
Calling OBs ..................................................................................................................................22
3.2.2
Called blocks................................................................................................................................23
3.2.3
Function .......................................................................................................................................23
3.2.4
Message behavior........................................................................................................................26
3.2.5
Assignment of the cyclic process image......................................................................................27
3.2.6
Addressing and module driver .....................................................................................................28
3.2.7
Processing the diagnostics data of the 3WL device ....................................................................28
3.2.8
Start-up characteristics ................................................................................................................29
3.2.9
Block parameters .........................................................................................................................29
3.2.10
Description of symbols and faceplates ........................................................................................60
3.3
Driver module DRV_3VL..............................................................................................................95
3.3.1
Calling OBs ..................................................................................................................................96
3.3.2
Called blocks................................................................................................................................96
3.3.3
Function .......................................................................................................................................96
3.3.4
Message behavior........................................................................................................................99
3.3.5
Assignment of the cyclic process image....................................................................................100
3.3.6
Addressing and module driver ...................................................................................................101
3.3.7
Processing the diagnostics data of the 3VL device ...................................................................102
3.3.8
Start-up characteristics ..............................................................................................................102
Table of contents
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
4
Function Manual, 11/2008, A5E02316914A-01
3.3.9
Block parameters ...................................................................................................................... 102
3.3.10
Description of symbols and faceplates ..................................................................................... 111
4
Configuration Manual............................................................................................................................. 125
4.1
Interconnections on COM15 for 3WL........................................................................................ 125
4.1.1
24V DC voltage......................................................................................................................... 126
4.1.2
Other voltage levels .................................................................................................................. 127
4.2
Interconnections on COM10 for 3VL......................................................................................... 128
4.2.1
Connection for communication ................................................................................................. 128
4.2.2
Connection for motorized operating mechanism ...................................................................... 129
4.3
Connection on COM20 for 3VL................................................................................................. 130
4.3.1
COM20 pin assignment............................................................................................................. 130
4.3.2
Connecting the optional motorized operating mechanism to COM20 ...................................... 131
4.4
Configuring a measuring point .................................................................................................. 132
4.4.1
Creating the PLC program ........................................................................................................ 132
4.4.2
Connection to WinCC................................................................................................................ 135
5
Technical specifications......................................................................................................................... 139
6
Technical support .................................................................................................................................. 141
Figures
Figure 1-1
Catalog path for incorporating via GSD file................................................................................... 8
Figure 1-2
Selection of basic type for 3WL .................................................................................................... 8
Figure 1-3
Selection of basic type for 3VL ..................................................................................................... 9
Figure 1-4
Properties of the 3WL / 3VL device directly connected to the DP master system...................... 10
Figure 1-5
Properties of the 3WL / 3VL device following a Y link ................................................................ 11
Figure 2-1
Section of the overview display................................................................................................... 13
Figure 2-2
Trend setting on the icon............................................................................................................. 14
Figure 2-3
Icons in Graphics Designer......................................................................................................... 15
Figure 3-1
Symbol with 1 measurement....................................................................................................... 61
Figure 3-2
Faceplate for standard view........................................................................................................ 63
Figure 3-3
Faceplate for measurements view, current tab........................................................................... 65
Figure 3-4
Faceplate for measurements view, voltage tab .......................................................................... 66
Figure 3-5
Faceplate for measurements view, active power/energy tab...................................................... 67
Figure 3-6
Faceplate for measurements view, reactive power/energy tab .................................................. 68
Figure 3-7
Faceplate for measurements view, apparent power tab............................................................. 69
Figure 3-8
Faceplate for measurements view, miscellaneous tab............................................................... 70
Figure 3-9
Faceplate for diagnosis view, warnings tab ................................................................................ 71
Figure 3-10
Faceplate for diagnosis view, trip reason tab.............................................................................. 72
Figure 3-11
Faceplate for diagnosis view, setpoints tab ................................................................................ 74
Figure 3-12
Faceplate for maintenance view, maintenance 1 tab ................................................................. 76
Table of contents
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
5
Figure 3-13
Faceplate for maintenance view, maintenance 2 tab ..................................................................77
Figure 3-14
Faceplate for maintenance view, operation tab...........................................................................79
Figure 3-15
Faceplate for protect. para view, parameter set A.......................................................................80
Figure 3-16
Faceplate for protect. para view, parameter set B.......................................................................82
Figure 3-17
Faceplate for protect. para view, additional tab...........................................................................84
Figure 3-18
Faceplate for ext. protect. para view, current tab ........................................................................85
Figure 3-19
Faceplate for ext. protect. para view, voltage tab........................................................................86
Figure 3-20
Faceplate for ext. protect. para view, reactive power tab............................................................87
Figure 3-21
Faceplate for ext. protect. para view, frequency tab....................................................................88
Figure 3-22
Faceplate for setpoints view, current tab.....................................................................................89
Figure 3-23
Faceplate for setpoints view, voltage tab.....................................................................................90
Figure 3-24
Faceplate for setpoints view, frequency tab ................................................................................91
Figure 3-25
Faceplate for setpoints view, active power tab............................................................................92
Figure 3-26
Faceplate for setpoints view, apparent/reactive power tab .........................................................94
Figure 3-27
Faceplate for message suppression view....................................................................................95
Figure 3-28
Symbol with 1 measurement......................................................................................................111
Figure 3-29
Faceplate for standard view.......................................................................................................113
Figure 3-30
Faceplate for measurements view.............................................................................................115
Figure 3-31
Faceplate for diagnosis view......................................................................................................116
Figure 3-32
Faceplate for maintenance view, maintenance 1 tab ................................................................118
Figure 3-33
Faceplate for maintenance view, operation tab.........................................................................119
Figure 3-34
Faceplate for protect. para view, protect. para tab ....................................................................120
Figure 3-35
Faceplate for protect. para view, additional tab.........................................................................121
Figure 3-36
Faceplate for ext. protect. para view..........................................................................................122
Figure 3-37
Faceplate for setpoints view ......................................................................................................123
Figure 3-38
Faceplate for message suppression view..................................................................................124
Figure 4-1
COM15 interconnection at 24V DC voltage...............................................................................126
Figure 4-2
COM15 interconnection at other voltage levels.........................................................................127
Figure 4-3
Connection for communication ..................................................................................................128
Figure 4-4
Connection for motorized operating mechanism .......................................................................129
Figure 4-5
COM20 connection to SENTRON VL ........................................................................................130
Figure 4-6
Driver block in CFC chart (not connected).................................................................................132
Figure 4-7
Compile program .......................................................................................................................133
Figure 4-8
Generate module driver .............................................................................................................133
Figure 4-9
Driver block in CFC chart connected.........................................................................................134
Figure 4-10
Basing the block icons on the plant hierarchy ...........................................................................135
Table of contents
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
6
Function Manual, 11/2008, A5E02316914A-01
Figure 4-11
Creating block icons out of plant hierarchy............................................................................... 136
Figure 4-12
Create block icons when compiling OS .................................................................................... 136
Figure 4-13
Link picture component with measuring point........................................................................... 137
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
7
Introduction
1
1.1
General
The Library SENTRON 3WL / 3VL for SIMATIC PCS 7 software package is used to connect
the circuit breakers SENTRON 3WL and 3VL to a SIMATIC PCS 7 process control system
and contains the following components:
● Block library with:
– DIA_WLVL: diagnostic block
– DRV_3WL: PCS 7 block for recording measurements, setpoints, protective
parameters, etc. of a 3WL circuit-breaker
– DRV_3VL: PCS 7 block for recording measurements, setpoints, protective
parameters, etc. of a 3VL circuit breaker
– User objects and operating blocks for operating and observing measured data on the
OS
● Online help in German and English
● Manual in German and English
The block library can be used in in the PCS 7 versions V6.1 SP1, V7.0 and V7.0 SP1.
1.2
Further documentation
You can find further details in the following manuals:
● Manual for SENTRON WL and SENTRON VL circuit-breakers with communication
capability
● SENTRON WL Operating Manual
● SENTRON VL Operating Manual
1.3
Installing the library
To start the installation, please insert the CD in the CD-ROM drive on your PG/PC and
launch the "Setup.exe" program. All the other information you need will be provided during
the installation process. Please also read the information in the readme file.
1.4 Hardware configuration
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
8
Function Manual, 11/2008, A5E02316914A-01
1.4
Hardware configuration
The driver concept for 3WL / 3VL supports operation of the circuit-breaker as a DP slave
directly connected to the DP master system as well as connected following a Y-link DPV0 or
DPV1.
The circuit-breakers in this setup can be incorporated using a GSD file.
NOTICE
In such cases ensure that the circuit-breaker's I/O data is within the control's process
image. This is absolutely essential to the driver generator's functionality.
1.4.1
Incorporating via GSD file
If the 3WL / 3VL device is incorporated via GSD SIEM80C0.gsd, it is entered in the hardware
configuration catalog under PROFIBUS-DP → Other field devices → Switchgear:
Figure 1-1
Catalog path for incorporating via GSD file
The following I/O configuration applies for 3WL:
● Outputs: 2 bytes of digital control data
● Inputs: 44 bytes of binary status (2 bytes) and measurements with property bytes (42
bytes)
Figure 1-2
Selection of basic type for 3WL
1.4 Hardware configuration
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
9
This configuration corresponds to basic type 3 for 3WL. This basic type must be set to
ensure operation.
The following I/O configuration applies for 3VL:
● Outputs: 2 bytes of digital control data
● Inputs: 14 bytes of binary status (2 bytes) and measurements with property bytes (12
bytes)
Figure 1-3
Selection of basic type for 3VL
This configuration corresponds to basic type 1 for 3VL. This basic type must be set to ensure
operation.
1.4 Hardware configuration
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
10
Function Manual, 11/2008, A5E02316914A-01
Configuration in HW config.
In the HW config., 3WL / 3VL is installed with the corresponding GSD file (see above) and
with basic type 3 and/or 1.
Figure 1-4
Properties of the 3WL / 3VL device directly connected to the DP master system
1.4 Hardware configuration
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
11
If 3WL / 3VL is connected following a Y-link DPV0 or DPV1, 3WL / 3VL must be configured
in the HW config. as a DPV0 slave. All acyclic services and interrupts are deactivated. This
means that the device no longer outputs diagnostic interrupts and data records can no
longer be read from the device. For details of the effect that this has on the response of the
blocks, refer to Section 3 Description of the blocks (Page 17).
Figure 1-5
Properties of the 3WL / 3VL device following a Y link
The start addresses of inputs and outputs must be located in the partial process image that
is assigned to the watchdog interrupt OB in which the driver block is called.
The LADDR parameter input of the driver block must be connected to the start address of
the inputs of the 3WL / 3VLdevice.
The assignment of the cyclic interface is included in the description of the driver block.
1.4 Hardware configuration
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
12
Function Manual, 11/2008, A5E02316914A-01
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
13
Information about the library
2
2.1
Overview of the blocks
The library contains the following blocks:
Name
Function
Number
DIA_WLVL
Diagnostic block
FB1742
DRV_3WL
PCS 7 driver block
FB1741
DRV_3VL
PCS 7 driver block
FB1740
2.2
General information about OS typicals
2.2.1
Faceplates
Faceplates are configured with the Graphics Designer using the templates and PCS 7-
specific standard views (Trend, Batch, and Alarm) provided by the Faceplate Designer. If
other user objects and functions are required, they can be added.
The faceplates described are provided as functional and tested examples and can be
adapted by the user.
Two icons and a group/loop display with all the necessary displays are provided for the
driver block. The relevant group display is called using the icons.
Overview
The display forms part of the @PG_DRV_3WL_OVERVIEW.pdl / @PL_DRV_3WL.pdl
(and/or @PG_DRV_3VL_OVERVIEW.pdl / @PL_DRV_3VL.pdl) basic displays.
(1)
Group display
(2)
Message lock (MSG_LOCK)
(3)
Message acknowledgment
(4)
Message suppression (QMSG_SUP)
Figure 2-1
Section of the overview display
Information about the library
2.2 General information about OS typicals
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
14
Function Manual, 11/2008, A5E02316914A-01
Trend (@PCS7_trend.pdl)
The "ReturnPath" and "StandardTrend" properties must be parameterized on the icon to
incorporate a trend in a faceplate.
2:
Online values with 5 min time axis
• StandardTrend
:
> 2:
Archive values with time axis of the value entered (in
min)
.AVGCUR
Structural element name starting with a full stop
:
Separators
CO_GREEN Color for trend
• ReturnPath:
,
Separators between two online values
Figure 2-2
Trend setting on the icon
Information about the library
2.2 General information about OS typicals
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
15
2.2.2
Symbols
The process display icons are based on the process symbols provided by the Faceplate
Designer. The diagrams are schematic diagrams.
Template pictures @PCS7Typicals_SENTRON.pdl / @Template_SENTRON.pdl
The icons can be found in the template diagrams @PCS7Typicals_SENTRON.pdl and
@Template_SENTRON.pdl.
When using the "Create/Update Block Icons" function, PCS 7 accesses the file
@PCS7Typicals_SENTRON.pdl .
When manually copying the icons into a process display, you must use the icons from the
@Template_SENTRON.pdl file.
Different variants of block icons
There may be several variants of block icons for one measuring point. These variants are
distinguished by the "type" attribute: The value of this attribute describes the variant. For
example, if you look at a variant of the block icon for a valve, you will find the value
"@Valve/2". You use the part of the value displayed after the "/" to control which variant of
the block icon is produced. You therefore have to enter this part in the object properties for
the block instance. If you do not enter any parameters in the object properties for the block
instance, the standard block icon is produced automatically: This is the block icon with the
"/1" label for the "type" attribute, e.g. "@Valve/1".
Only one version is however supplied per circuit breaker type with the library.
Connection to the measuring point
There is one icon for the driver block that is linked to the associated measuring point using
the "Connect picture block to tag structure" function.
The icons contain the following visible information:
(1)
Tag name
(2)
Maximum phase current
(3)
Group display (EventState)
(4)
Circuit breaker in manual (M) / automatic (A)
(5)
Circuit breaker state
Figure 2-3
Icons in Graphics Designer
Information about the library
2.2 General information about OS typicals
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
16
Function Manual, 11/2008, A5E02316914A-01
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
17
Description of blocks
3
The library consists of the blocks described below:
● Diagnostic block (Page 17) DIA_WLVL
● Driver block (Page 22) DRV_3WL
● Driver block (Page 95) DRV_3VL
3.1
Diagnostics block DIA_WLVL
FB1742
The DRV_3WL and DRV_3VL driver blocks have a shared diagnostics block DIA_WLVL.
Description of block:
● Calling OBs (Page 18)
● Called blocks (Page 18)
● Function (Page 18)
● Message behavior (Page 18)
● Error behavior (Page 19)
● I/O access error (Page 19)
● Module fault (Page 19)
● Read diagnostics data of 3WL / 3VL (Page 19)
● Start-up characteristics (Page 20)
● Block parameters (Page 20)
See also
Driver module DRV_3WL (Page 22)
Driver module DRV_3VL (Page 95)
Description of blocks
3.1 Diagnostics block DIA_WLVL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
18
Function Manual, 11/2008, A5E02316914A-01
3.1.1
Calling OBs
The block must be installed in the processing sequence in the following OBs (occurs
automatically in the CFC):
OB1
Cyclic program
OB82
Diagnostic interrupt
OB83
Insert/remove module interrupt
OB85
Program error
OB86
Rack failure
OB100 Warm restart
Installation is performed automatically by means of the function "Generate Module Driver"
3.1.2
Called blocks
The block calls the following blocks:
SFC6
RD_SINFO
SFC51
RDSYSST
3.1.3
Function
The DIA_WLVL block is responsible for diagnosis of the 3WL / 3VL device.
If a 3WL / 3VL is directly connected to the DP master system, the block evaluates the acyclic
events that are relevant for 3WL / 3VL (start-up, DP station failure, module fault), generates
quality code and diagnostic information for the MOD_PAX0 block and provides the driver
block with status information via parameter output OMODE.
In the case of operation following a Y link DPV1, diagnostic information cannot be supplied
to the driver block. The block evaluates start-up, DP station failure and module faults and
provides the driver block with this information via parameter output OMODE.
This block is not used in the case of connection following Y link DPV0.
3.1.4
Message behavior
The block has no message behavior. The messages for DP station failure and module fault
are generated by the MOD_PAX0 block (in the case of direct connection to the DP master
system) or PADP_L00 (in the case of connection following the Y link DPV0) or OB_DIAG1 (in
the case of connection following the Y link DPV1).
Description of blocks
3.1 Diagnostics block DIA_WLVL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
19
3.1.5
Error behavior
Failure of the DP master or DP slave has already been determined by the previous
OB_DIAG1 block and evaluated by the RACKF, SUBN1ERR and SUBN2ERR inputs.
In the event of an error, the output OMODE features the identifier for "higher-ranking error"
(OMODE = 16#40xxxxxx).
3.1.6
I/O access error
From the viewpoint of the I/O configuration, 3WL / 3VL is a "compact" DP slave, i.e. it always
has a fixed I/O configuration. It can therefore be assumed that if an I/O access error occurs,
the entire DP slave must have failed (which is reported shortly afterwards).
I/O access errors are not evaluated any further, for this reason.
3.1.7
Module fault
Following a restart and when ACC_ID = TRUE, the module addressed with LADDR is
checked. SZL ID xC91 is read for this purpose. If the module addressed with LADDR does
not exist, the output QMODF is set and the identifier for "higher-ranking error" is entered for
the OMODE output (OMODE=16#40xxxxxx).
3.1.8
Read diagnostics data of 3WL / 3VL
If the 3WL / 3VL outputs a diagnostics alarm, system function RDSYSST (SFC51) will
activate reading of the device-specific diagnostics data.
The device-specific diagnostics data is also read out using the system function RDSYSST
(SFC51) following a CPU restart and rack start-up.
Since 3WL / 3VL following a Y link switches over to DPV0 mode, the device-specific
diagnostics data cannot be read.
The read information is transferred to the MOD_PAX0 block and the driver block where it is
evaluated.
It is also read if a request is output by the driver block at the "DIAG_REQ" input. This occurs
if:
● MAINT_MC ! = 0
● R_MAINT = 1
● Cyclically at DIAREQ_T ! = 0.0 min
The diagnostics data can also be displayed on a Maintenance Station (MS).
Description of blocks
3.1 Diagnostics block DIA_WLVL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
20
Function Manual, 11/2008, A5E02316914A-01
Diagnostic events are assigned to maintenance status as follows:
Diagnostic event
Maintenance status
QUALITY
PA_DIAG
Perform visual inspection on main contacts
Maintenance
requirement is
medium
16#68
16#0020_0000
Immediate maintenance of main contacts
Maintenance
requirement is high
16#24
16#0100_0000
3.1.9
Start-up characteristics
In OB100, the identifier for "Start up" is entered for output OMODE (OMODE=16#xx01xxxx).
3.1.10
Block parameters
The as-supplied state of the block displayed in CFC is shown in the "I/O" column: I/O name
bold = I/O is visible, normal = I/O is invisible.
I/O (parameter)
Comment
Data type
Default
Type
OCM
EN_DIAG
1 = Enable read diagnostic data
BOOL
FALSE
I
MODE
Parameter OMODE of DRV_WLVL
WORD
0
I
LADDR
Logical address of module
INT
0
I
DADDR
Diagnostic address of module
INT
0
I
DPA_LINK
Device connection:
0 = DP-MASTER,
1 = DP/PA-LINK
BOOL
FALSE
I
SUBN_TYP
1 = External DP interface
BOOL
FALSE
I
SUBN1_ID
ID of Primary Subnet
BYTE
16#FF
I
SUBN2_ID
ID of Redundant Subnet
BYTE
16#FF
I
RACK_NO
Rack number
BYTE
0
I
RACKF
1 = Rack failure
BOOL
FALSE
I
SUBN1ERR
1 = Slave 1 Failure
BOOL
FALSE
I
SUBN2ERR
1 = Slave 2 Failure
BOOL
FALSE
I
ACC_ID
1 = Accept new mode settings
BOOL
TRUE
IO
DIAG_REQ
1 = Read diagnostic information
BOOL
FALSE
I
QERR
1 = Error
BOOL
FALSE
O
QMODF
1 = Module Failure
BOOL
FALSE
O
QRACKF
1 = Rack failure
BOOL
FALSE
O
RACK1ERR
1 = DP slave system failure (primary)
BOOL
FALSE
O
RACK2ERR
1 = DP slave system failure (redundant)
BOOL
FALSE
O
QUALITY
Quality code of process value
BYTE
0
O
OMODE
Status MODE
DWORD
0
O
Description of blocks
3.1 Diagnostics block DIA_WLVL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
21
I/O (parameter)
Comment
Data type
Default
Type
OCM
PA_DIAG
Diagnostic information for maintenance
DWORD
0
O
QDIAG_INF
Diagnostic information
WORD
0
O
Structure of OMODE
Byte
Value
Meaning
Byte 3
16#80: Valid data
16#40: Invalid data
Higher-level fault
Byte 2
16#01: Cold restart (OB100)
Byte 1; 0
16#0000
Irrelevant
Structure of QDIAG_INF
VALUE
Meaning
0
Everything ok
1
Perform visual inspection on main contacts
2
Immediate maintenance of main contacts
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
22
Function Manual, 11/2008, A5E02316914A-01
3.2
Driver module DRV_3WL
FB1741
Description of block:
● Calling OBs (Page 22)
● Called blocks (Page 23)
● Function (Page 23)
● Message behavior (Page 26)
● Assignment of the cyclic process image (Page 27)
● Addressing and module driver (Page 28)
● Processing the diagnostics data of the 3WL device (Page 28)
● Start-up characteristics (Page 29)
● Block parameters (Page 29)
● Description of symbols and faceplates (Page 60)
See also
Diagnostics block DIA_WLVL (Page 17)
Driver module DRV_3VL (Page 95)
3.2.1
Calling OBs
The OB watchdog interrupt in which the block is installed (e.g. OB32). Also in OB100
(performed automatically in CFC, see start-up characteristics).
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
23
3.2.2
Called blocks
The block calls the following blocks:
SFB35
ALARM_8P
SFB52
RDREC
SFB53
WRREC
SFC1
READ_CLK
SFC6
RD_SINFO
SFC20
BLKMOV
SFC21
FILL
3.2.3
Function
The DRV_3WL block is used for measurement acquisition and control and it forms the
interface to the OS.
Automatic / manual mode switch over
Automatic and manual mode are available for operating the driver block. When in manual
mode, the user can control the circuit breaker position (ON / OFF) of the faceplate in WinCC.
When in automatic mode, the corresponding buttons are locked (cannot be operated) in the
faceplate and the circuit breaker is controlled by input parameters which can be connected in
the CFC (AUTO_ON / AUTO_OFF) and therefore by the AS program.
The user can define the mode in which the block is to run in the faceplate or in a block
parameter (AUT_L).
The setting at the LIOP_SEL input determines which of the parameters is currently active.
NOTICE
If an error occurs (monitoring error, Local turn off, Tripped) the block changes to Forced
manual. If the pending error state is acknowledged with one of the RESET buttons, the
block goes into the specified mode again.
If Automatic mode is specified by the AS program (LIOP_SEL = 1, AUT_L = 1) the
commands present at AUTO_ON or AUTO_OFF are always output.
Under certain circumstances this means that resetting error states may cause a switching
operation of the circuit breaker. If this is not desired the user must configure the AS
program accordingly.
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
24
Function Manual, 11/2008, A5E02316914A-01
Switching the circuit breaker on/off
The user can use the driver block to switch the circuit breaker.
It is important to note here that the ON state means "main contacts closed" and the OFF
state means "main contacts open".
The circuit breaker cannot be switched on or off in certain states:
It must not be switched on when:
• there is a monitoring error
(QMON_ERR = 1)
• the block is in maintenance mode
(MAINT = 1)
• write protection applies
(QWR_PROT = 1)
• the circuit breaker is already on
(QON = 1)
• the circuit breaker has tripped
(QTRIP = 1)
• the circuit breaker has been switched off locally
(QLOC_OFF = 1)
• the circuit breaker is not ready for an On command
(RDY_ON = 0)
It must not be switched off when:
• there is a monitoring error
(QMON_ERR = 1)
• the block is in maintenance mode
(MAINT = 1)
• write protection applies
(QWR_PROT = 1)
• the circuit breaker is already off
(QOFF = 1)
• the circuit breaker has tripped
(QTRIP = 1)
• the circuit breaker has been switched off locally
(QLOC_OFF = 1)
Resetting Tripped and Local turn off states
If the block is in one of the two states, it has to be reset before an On command can be
output again. The faceplate features a corresponding button for the user for this RESET.
CAUTION
Before the circuit breaker is switched back on, the reason for tripping/switching off must be
established and possible error causes must be rectified.
NOTICE
If such a state is reset the response of the mode must be observed as it may cause a
switching operation of the circuit breaker under certain circumstances.
See Automatic / Manual mode switchover
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
25
Feedback monitoring
When monitoring is activated (MONITOR = On), switching commands (ON / OFF) and the
resetting of trips are time monitored. If the expected state is not reached after an operation
and within the monitoring time (TIME_MON), the block outputs a message and goes into a
resetting state (QMON_ERR).
The faceplate features an appropriate RESET button for resetting this state again.
NOTICE
If the monitoring error is reset the response of the mode must be observed as it may cause
a switching operation of the circuit breaker under certain circumstances.
See Automatic / Manual mode switchover
Measured value acquisition
The block reads measured values from the cyclic process image.
When operating 3WL on the DP master system directly, the block also reads data record 94
with the system function block RDREC (SFB52).
The data record is read in a defined cycle. The interval at which the data record can be read
can be set in seconds using the input parameter CYCLE_T. The default setting is 60
seconds. A cycle of 0 seconds or less means that this data record is not read.
Time synchronization
Data record 68 writes the current time in cycles in order to transfer the current time to the
circuit breaker. This cycle can be set in seconds using the TIME_SYNC_T parameter.
Diagnostics and maintenance
In order to display the current state of the circuit breaker, modules present, statistics
information and diagnostic messages, the module reads the status word from the process
image and data records 91 and 92.
The process image is called in cycles. The user can request the data records in the faceplate
via operations. The diagnostic messages are updated in cycles when messages are present.
WARNING
During maintenance work on the circuit breaker, maintenance mode must be activated!
At the same time, the circuit breaker must be locked locally to prevent it being switched
back on.
Maintenance specifications apply to the circuit breakers (in accordance with EN 50 110-1,
DIN VDE 0105-100 and BGV A2).
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
26
Function Manual, 11/2008, A5E02316914A-01
Protect. parameter and extended protect. parameter
This data, which comes from data records 128 and 129, is updated for the display in the
faceplate if requested by the operator.
These parameters cannot be written.
Setpoints
These parameters can be read and written from the faceplate.
3.2.4
Message behavior
DRV_3WL issues the following messages:
Message block
Message
number
Message text
Message class
1
Overload tripping (L)
AH
2
Instantaneous short-circuit (I)
AH
3
Short-time-delay short-circuit (S)
AH
4
Ground fault (G)
AH
5
Trip as a result of extended protection function
AH
6
Overload in neutral conductor
AH
7
Overload warning present
WH
MSG_EVID1
8
An activated setpoint value has been exceeded
WH
1
An alarm signal is currently present
WH
2
Error time synchronization
WH
3
Local turn off of circuit breaker / tripped
AH
4
Load shedding warning
WH
5
Perform visual inspection on main contacts
WH
6
Immediate maintenance of main contacts
AH
7
Monitoring error
AS Control System
Fault
MSG_EVID2
8
Forbidden switching command for auto mode - switching
command ignored
AS Control System
Fault
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
27
Auxiliary values
EV_ID
Auxiliary value
Block parameters
1
AUX_PR01
2
AUX_PR02
3
AUX_PR03
4
AUX_PR04
5
AUX_PR05
6
AUX_PR06
7
AUX_PR07
8
AUX_PR08
9
AUX_PR09
MSG_EVID1
-
MSG_EVID2
10
AUX_PR10
3.2.5
Assignment of the cyclic process image
Only basic type 3 is supported in the default setting.
Name
Inputs
Outputs
0 / 1
Control bytes
2
0 / 1
Binary status information
2
2 / 3
Current in phase 1
2
4 / 5
Current in phase 2
2
6 / 7
Current in phase 3
2
8 / 9
Max. current in phase under highest load
2
10 / 11
Current in neutral conductor
2
12 / 13
Phase-to-phase voltage L12
2
14 / 15
Phase-to-phase voltage L23
2
16 / 17
Phase-to-phase voltage L31
2
18 / 19
Neutral-point star voltage L1N
2
20 / 21
Neutral-point star voltage L2N
2
22 / 23
Neutral-point star voltage L3N
2
24 / 25
Mean value of power factors of 3 phases
2
26 / 27
Total active energy of 3 phases
2
28 / 29
Total apparent power of 3 phases
2
30
EB of current phase 1
1
31
EB of current phase 2
1
32
EB of current phase 3
1
33
EB of max. current in phase under highest load
1
34
EB of current in neutral conductor
1
35
EB of phase-to-phase voltage L12
1
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
28
Function Manual, 11/2008, A5E02316914A-01
Name
Inputs
Outputs
36
EB of phase-to-phase voltage L23
1
37
EB of phase-to-phase voltage L31
1
38
EB of neutral-point star voltage L1N
1
39
EB of neutral-point star voltage L2N
1
40
EB of neutral-point star voltage L3N
1
41
EB of mean value of the three power factors
1
42
EB of total active energy
1
43
EB of total apparent power
1
Number of bytes
44
2
3.2.6
Addressing and module driver
The I/O addresses of 3WL must lie completely within the process image of the CPU. In the
CFC chart, the LADDR input is connected to the base address of the 3WL device.
Procedure:
Select input parameter → right mouse button → Interconnection to
address... → Entere.g. EW512
If 3WL is directly connected to the DP master system, the module driver connects block
outputs OMODE, QRACKF and QMODF to inputs MODE00, RACKF and MODF of the block
MOD_PAX0 and the module driver connects input DIAG_INF to output QDIAG_INF of
diagnostics block DIA_WLVL.
In the case of operation following a Y-Link DPV1, the module driver connects block inputs
MODE, RACKF and DIAG_INF to outputs OMODE, QRACKF and QDIAG_INF of
diagnostics block DIA_WLVL.
In the case of operation following a Y-Link DPV0, the module driver connects block inputs
MODE and RACKF to outputs OMODE00 and QRACKF of block PADP_L00.
The block input BASADR is parameterized with the logical base address of the 3WL device
by the module driver.
The block input BASADR_OUT is parameterized with the start address of the outputs of the
3WL device by the module driver.
The input DPA_LINK is parameterized with the connection mode of the 3WL device by the
module driver.
● DPA_LINK = 0 -> Directly connected to the DP master
● DPA_LINK = 1 -> Connected following a DP/PA link
3.2.7
Processing the diagnostics data of the 3WL device
If 3WL is directly connected to the DP master system, the block processes the diagnostic
information that is supplied to it from the DIA_WLVL diagnostics block via the input
DIAG_INF.
The user has the possibility of setting the cycle for cyclic reading of the diagnostics data
record at the "DIAREQ_T" input. At DIAREQ_T = 0.0 minutes no cyclic reading takes place.
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
29
3.2.8
Start-up characteristics
On starting, messages are deactivated (OB100).
3.2.9
Block parameters
The as-supplied state of the block displayed in CFC is shown in the "I/O" column: I/O name
bold = I/O is visible, normal = I/O is invisible.
I/O (parameter)
Comment
Data type
Default
Type
OCM
MODE
Parameter OMODE of DIA_WLVL
DWORD
0
I
RACKF
1 = Rack failure
BOOL
FALSE
I
LADDR
Base address of 3WL module
WORD
0
I
BASADR
Base address of 3WL module
INT
0
I
BASADR_OUT
Base address of 3WL module for outputs
INT
0
I
DPA_LINK
Device connection: 0 = DP-MASTER,
1 = DP/PA-LINK
BOOL
FALSE
I
x
MSG_LOCK
1 = Messages locked
BOOL
FALSE
I
x
RUNUPCYC
Lag: Number of run up cycles
INT
0
I
SAMPLE_T
Sample time [s]
REAL
0.0
I
CYCLE_T
Cycle time of cyclic reading of DRs [s]
REAL
60.0
I
TIME_SYNC_T
Cycle time of time synchronization [min]
REAL
10.0
I
DIAREQ_T
Cycle time of reading diagnostic
information [min]
BOOL
FALSE
O
DR94_K
1 = kWh inputs for real and reactive energy
of DR 94 are used
BOOL
FALSE
I
x
MONITOR
1 = Monitoring activated
BOOL
TRUE
I
TIME_MON
Monitoring time [s]
REAL
10.0
I
DIAG_INF
Diagnostic info for driver
WORD
0
I
ALT_SYM
1 = Alternative symbols
BOOL
FALSE
I
MANOP_EN
1 = Operator may input MANUAL
BOOL
TRUE
I
AUTOP_EN
1 = Operator may input AUTO
BOOL
TRUE
I
LIOP_SEL
1 = Linking, 0 = Operator active
BOOL
FALSE
I
AUT_L
Linkable input for MANUAL/AUTO mode
BOOL
FALSE
I
AUTO_ON
AUTO mode: Switch off (open the main
contacts)
BOOL
FALSE
I
AUTO_OFF
AUTO mode: Switch on (close the main
contacts)
BOOL
FALSE
I
MSG_EVID1
Message ID message block 1
DWORD
0
I
MSG_EVID2
Message ID message block 2
DWORD
0
I
SUP_OVLD_WRN
1 = Active message suppression
BOOL
FALSE
I
x
SUP_SP_EXCEED
1 = Active message suppression
BOOL
FALSE
I
x
SUP_WRN
1 = Active message suppression
BOOL
FALSE
I
x
SUP_LD_SHED
1 = Active message suppression
BOOL
FALSE
I
x
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
30
Function Manual, 11/2008, A5E02316914A-01
I/O (parameter)
Comment
Data type
Default
Type
OCM
RP_NORM_I
DR 130: Real power in normal direction
REAL
0.0
I
x
RP_NORM_I_QC
Quality code of RP_NORM_I
BYTE
0
I
RP_NORM_I_OFF
DR 130: Real power in normal direction
OFF
BOOL
FALSE
I
x
RP_NORM_I_NA
DR 130: Real power in normal direction
not available
BOOL
FALSE
I
x
RP_REV_I
DR 130: Real power in reverse direction
REAL
0.0
I
x
RP_REV_I_QC
Quality code of RP_REV_I
BYTE
0
I
RP_REV_I_OFF
DR 130: Real power in reverse direction
OFF
BOOL
FALSE
I
x
RP_REV_I_NA
DR 130: Real power in reverse direction
not available
BOOL
FALSE
I
x
PF_CAP_I
DR 130: Power factor capacitive
REAL
0.0
I
x
PF_CAP_I_QC
Quality code of PF_CAP_I
BYTE
0
I
PF_CAP_I_OFF
DR 130: Power factor capacitive OFF
BOOL
FALSE
I
x
PF_CAP_I_NA
DR 130: Power factor capacitive not
available
BOOL
FALSE
I
x
PF_IND_I
DR 130: Power factor inductive
REAL
0.0
I
x
PF_IND_I_QC
Quality code of PF_IND_I
BYTE
0
I
PF_IND_I_OFF
DR 130: Power factor inductive OFF
BOOL
FALSE
I
x
PF_IND_I_NA
DR 130: Power factor inductive not
available
BOOL
FALSE
I
x
T_RP_NORM_I
DR 130: Delay time for real power in
normal direction
REAL
0.0
I
x
T_RP_NORM_I_QC
Quality code of T_RP_NORM_I
BYTE
0
I
T_RP_NORM_I_OFF
DR 130: Delay time for real power in
normal direction OFF
BOOL
FALSE
I
x
T_RP_NORM_I_NA
DR 130: Delay time for real power in
normal direction not available
BOOL
FALSE
I
x
T_RP_REV_I
DR 130: Delay time for real power in
reverse direction
REAL
0.0
I
x
T_RP_REV_I_QC
Quality code of T_RP_REV_I
BYTE
0
I
T_RP_REV_I_OFF
DR 130: Delay time for real power in
reverse direction OFF
BOOL
FALSE
I
x
T_RP_REV_I_NA
DR 130: Delay time for real power in
reverse direction not available
BOOL
FALSE
I
x
T_PF_CAP_I
DR 130: Delay time for power factor
capacitive
REAL
0.0
I
x
T_PF_CAP_I_QC
Quality code of T_PF_CAP_I
BYTE
0
I
T_PF_CAP_I_OFF
DR 130: Delay time for power factor
capacitive OFF
BOOL
FALSE
I
x
T_PF_CAP_I_NA
DR 130: Delay time for power factor
capacitive not available
BOOL
FALSE
I
x
T_PF_IND_I
DR 130: Delay time for power factor
inductive
REAL
0.0
I
x
T_PF_IND_I_QC
Quality code of T_PF_IND_I
BYTE
0
I
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
31
I/O (parameter)
Comment
Data type
Default
Type
OCM
T_PF_IND_I_OFF
DR 130: Delay time for power factor
inductive OFF
BOOL
FALSE
I
x
T_PF_IND_I_NA
DR 130: Delay time for power factor
inductive not available
BOOL
FALSE
I
x
OVER_FRQ_I
DR 130: Over frequency
REAL
0.0
I
x
OVER_FRQ_I_QC
Quality code of OVER_FRQ_I
BYTE
0
I
OVER_FRQ_I_OFF
DR 130: Over frequency OFF
BOOL
FALSE
I
x
OVER_FRQ_I_NA
DR 130: Over frequency not available
BOOL
FALSE
I
x
T_OVER_FRQ_I
DR 130: Delay time for over frequency
REAL
0.0
I
x
T_OVER_FRQ_I_QC
Quality code of T_OVER_FRQ_I
BYTE
0
I
T_OVER_FRQ_I_OFF
DR 130: Delay time for over frequency
OFF
BOOL
FALSE
I
x
T_OVER_FRQ_I_NA
DR 130: Delay time for over frequency not
available
BOOL
FALSE
I
x
UNDER_FRQ_I
DR 130: Under frequency
REAL
0.0
I
x
UNDER_FRQ_I_QC
Quality code of UNDER_FRQ_I
BYTE
0
I
UNDER_FRQ_I_OFF
DR 130: Under frequency OFF
BOOL
FALSE
I
x
UNDER_FRQ_I_NA
DR 130: Under frequency not available
BOOL
FALSE
I
x
T_UNDER_FRQ_I
DR 130: Delay time for under frequency
REAL
0.0
I
x
T_UNDER_FRQ_I_QC
Quality code of T_UNDER_FRQ_I
BYTE
0
I
T_UNDER_FRQ_I_OFF
DR 130: Delay time for under frequency
OFF
BOOL
FALSE
I
x
T_UNDER_FRQ_I_NA
DR 130: Delay time for under frequency
not available
BOOL
FALSE
I
x
CUR_THD_I
DR 130: THD current
REAL
0.0
I
x
CUR_THD_I_QC
Quality code of CUR_THD_I
BYTE
0
I
CUR_THD_I_OFF
DR 130: THD current OFF
BOOL
FALSE
I
x
CUR_THD_I_NA
DR 130: THD current not available
BOOL
FALSE
I
x
T_CUR_THD_I
DR 130: Delay time for THD current
REAL
0.0
I
x
T_CUR_THD_I_QC
Quality code of T_CUR_THD_I
BYTE
0
I
T_CUR_THD_I_OFF
DR 130: Delay time for THD current OFF
BOOL
FALSE
I
x
T_CUR_THD_I_NA
DR 130: Delay time for THD current not
available
BOOL
FALSE
I
x
VOLT_THD_I
DR 130: THD voltage
REAL
0.0
I
x
VOLT_THD_I_QC
Quality code of VOLT_THD_I
BYTE
0
I
VOLT_THD_I_OFF
DR 130: THD voltage OFF
BOOL
FALSE
I
x
VOLT_THD_I_NA
DR 130: THD voltage not available
BOOL
FALSE
I
x
T_VOLT_THD_I
DR 130: Delay time for THD voltage
REAL
0.0
I
x
T_VOLT_THD_I_QC
Quality code of T_VOLT_THD_I
BYTE
0
I
T_VOLT_THD_I_OFF
DR 130: Delay time for THD voltage OFF
BOOL
FALSE
I
x
T_VOLT_THD_I_NA
DR 130: Delay time for THD voltage not
available
BOOL
FALSE
I
x
CREST_F_I
DR 130: Crest factor
REAL
0.0
I
x
CREST_F_I_QC
Quality code of CREST_F_I
BYTE
0
I
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
32
Function Manual, 11/2008, A5E02316914A-01
I/O (parameter)
Comment
Data type
Default
Type
OCM
CREST_F_I_OFF
DR 130: Crest factor OFF
BOOL
FALSE
I
x
CREST_F_I_NA
DR 130: Crest factor not available
BOOL
FALSE
I
x
FORM_F_I
DR 130: Form factor
REAL
0.0
I
x
FORM_F_I_QC
Quality code of FORM_F_I
BYTE
0
I
FORM_F_I_OFF
DR 130: Form factor OFF
BOOL
FALSE
I
x
FORM_F_I_NA
DR 130: Form factor not available
BOOL
FALSE
I
x
T_CREST_F_I
DR 130: Delay time for crest factor
REAL
0.0
I
x
T_CREST_F_I_QC
Quality code of T_CREST_F_I
BYTE
0
I
T_CREST_F_I_OFF
DR 130: Delay time for crest factor OFF
BOOL
FALSE
I
x
T_CREST_F_I_NA
DR 130: Delay time for crest factor not
available
BOOL
FALSE
I
x
T_FORM_F_I
DR 130: Delay time for form factor
REAL
0.0
I
x
T_FORM_F_I_QC
Quality code of T_FORM_F_I
BYTE
0
I
T_FORM_F_I_OFF
DR 130: Delay time for form factor OFF
BOOL
FALSE
I
x
T_FORM_F_I_NA
DR 130: Delay time for form factor not
available
BOOL
FALSE
I
x
RP_DEM_I
DR 130: Demand real power
REAL
0.0
I
x
RP_DEM_I_QC
Quality code of PR_DEM_I
BYTE
0
I
RP_DEM_I_OFF
DR 130: Demand real power OFF
BOOL
FALSE
I
x
RP_DEM_I_NA
DR 130: Demand real power not available
BOOL
FALSE
I
x
AP_DEM_I
DR 130: Demand apparent power
REAL
0.0
I
x
AP_DEM_I_QC
Quality code of AP_DEM_I
BYTE
0
I
AP_DEM_I_OFF
DR 130: Demand apparent power OFF
BOOL
FALSE
I
x
AP_DEM_I_NA
DR 130: Demand apparent power not
available
BOOL
FALSE
I
x
T_RP_DEM_I
DR 130: Delay time demand of the real
power
REAL
0.0
I
x
T_RP_DEM_I_QC
Quality code of T_RP_DEM_I
BYTE
0
I
T_RP_DEM_I_OFF
DR 130: Delay time demand of the real
power OFF
BOOL
FALSE
I
x
T_RP_DEM_I_NA
DR 130: Delay time demand of the real
power not available
BOOL
FALSE
I
x
T_AP_DEM_I
DR 130: Delay time demand of the
apparent power
REAL
0.0
I
x
T_AP_DEM_I_QC
Quality code of T_AP_DEM_I
BYTE
0
I
T_AP_DEM_I_OFF
DR 130: Delay time demand of the
apparent power OFF
BOOL
FALSE
I
x
T_AP_DEM_I_NA
DR 130: Delay time demand of the
apparent power not available
BOOL
FALSE
I
x
RAP_DEM_I
DR 130: Demand reactive power
REAL
0.0
I
x
RAP_DEM_I_QC
Quality code of RAP_DEM_I
BYTE
0
I
RAP_DEM_I_OFF
DR 130: Demand reactive power OFF
BOOL
FALSE
I
x
RAP_DEM_I_NA
DR 130: Demand reactive power not
Available
BOOL
FALSE
I
x
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
33
I/O (parameter)
Comment
Data type
Default
Type
OCM
RAP_NORM_I
DR 130: Reactive power in normal
direction
REAL
0.0
I
x
RAP_NORM_I_QC
Quality code of RAP_NORM_I
BYTE
0
I
RAP_NORM_I_OFF
DR 130: Reactive power in normal
direction OFF
BOOL
FALSE
I
x
RAP_NORM_I_NA
DR 130: Reactive power in normal
direction not available
BOOL
FALSE
I
x
T_RAP_DEM_I
DR 130: Delay time demand of the
reactive power
REAL
0.0
I
x
T_RAP_DEM_I_QC
Quality code of T_RAP_DEM_I
BYTE
0
I
T_RAP_DEM_I_OFF
DR 130: Delay time demand of the
reactive power OFF
BOOL
FALSE
I
x
T_RAP_DEM_I_NA
DR 130: Delay time demand of the
reactive power not available
BOOL
FALSE
I
x
T_RAP_NORM_I
DR 130: Delay time for reactive power in
normal direction
REAL
0.0
I
x
T_RAP_NORM_I_QC
Quality code of T_RAP_NORM_I
BYTE
0
I
T_RAP_NORM_I_OFF
DR 130: Delay time for reactive power in
normal direction OFF
BOOL
FALSE
I
x
T_RAP_NORM_I_NA
DR 130: Delay time for reactive power in
normal direction not available
BOOL
FALSE
I
x
RAP_REV_I
DR 130: Reactive power in reverse
direction
REAL
0.0
I
x
RAP_REV_I_QC
Quality code of RAP_REV_I
BYTE
0
I
RAP_REV_I_OFF
DR 130: Reactive power in reverse
direction OFF
BOOL
FALSE
I
x
RAP_REV_I_NA
DR 130: Reactive power in reverse
direction not available
BOOL
FALSE
I
x
AP_I
DR 130: Apparent power
REAL
0.0
I
x
AP_I_QC
Quality code of AP_I
BYTE
0
I
AP_I_OFF
DR 130: Apparent power OFF
BOOL
FALSE
I
x
AP_I_NA
DR 130: Apparent power not available
BOOL
FALSE
I
x
T_RAP_REV_I
DR 130: Delay time for reactive power in
reverse direction
REAL
0.0
I
x
T_RAP_REV_I_QC
Quality code of T_RAP_REV_I
BYTE
0
I
T_RAP_REV_I_OFF
DR 130: Delay time for reactive power in
reverse direction OFF
BOOL
FALSE
I
x
T_RAP_REV_I_NA
DR 130: Delay time for reactive power in
reverse direction not available
BOOL
FALSE
I
x
T_AP_I
DR 130: Delay time for apparent power
REAL
0.0
I
x
T_AP_I_QC
Quality code of T_AP_I
BYTE
0
I
T_AP_I_OFF
DR 130: Delay time for apparent power
OFF
BOOL
FALSE
I
x
T_AP_I_NA
DR 130: Delay time for apparent power not
available
BOOL
FALSE
I
x
CUR_OVER_I
DR 130: Over current
REAL
0.0
I
x
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
34
Function Manual, 11/2008, A5E02316914A-01
I/O (parameter)
Comment
Data type
Default
Type
OCM
CUR_OVER_I_QC
Quality code of CUR_OVER_I
BYTE
0
I
CUR_OVER_I_OFF
DR 130: Over current OFF
BOOL
FALSE
I
x
CUR_OVER_I_NA
DR 130: Over current not available
BOOL
FALSE
I
x
CUR_GRD_I
DR 130: Earth fault current
REAL
0.0
I
x
CUR_GRD_I_QC
Quality code of CUR_GRD_I
BYTE
0
I
CUR_GRD_I_OFF
DR 130: Earth fault current OFF
BOOL
FALSE
I
x
CUR_GRD_I_NA
DR 130: Earth fault current not available
BOOL
FALSE
I
x
CUR_N_I
DR 130: Over current N-phase
REAL
0.0
I
x
CUR_N_I_QC
Quality code of CUR_N_I
BYTE
0
I
CUR_N_I_OFF
DR 130: Over current N-phase OFF
BOOL
FALSE
I
x
CUR_N_I_NA
DR 130: Over current N-phase not
available
BOOL
FALSE
I
x
CUR_DEM_I
DR 130: Demand of the current
REAL
0.0
I
x
CUR_DEM_I_QC
Quality code of CUR_DEM_I
BYTE
0
I
CUR_DEM_I_OFF
DR 130: Demand of the current OFF
BOOL
FALSE
I
x
CUR_DEM_I_NA
DR 130: Demand of the current not
available
BOOL
FALSE
I
x
T_CUR_OVER_I
DR 130: Delay time for over current
REAL
0.0
I
x
T_CUR_OVER_I_QC
Quality code of T_CUR_OVER_I
BYTE
0
I
T_CUR_OVER_I_OFF
DR 130: Delay time for over current OFF
BOOL
FALSE
I
x
T_CUR_OVER_I_NA
DR 130: Delay time for over current not
available
BOOL
FALSE
I
x
T_CUR_GRD_I
DR 130: Delay time for over current
ground
REAL
0.0
I
x
T_CUR_GRD_I_QC
Quality code of T_CUR_GRD_I
BYTE
0
I
T_CUR_GRD_I_OFF
DR 130: Delay time for over current
ground OFF
BOOL
FALSE
I
x
T_CUR_GRD_I_NA
DR 130: Delay time for over current
ground not available
BOOL
FALSE
I
x
T_CUR_N_I
DR 130: Delay time for over current N-
phase
REAL
0.0
I
x
T_CUR_N_I_QC
Quality code of T_CUR_N_I
BYTE
0
I
T_CUR_N_I_OFF
DR 130: Delay time for over current N-
phase OFF
BOOL
FALSE
I
x
T_CUR_N_I_NA
DR 130: Delay time for over current N-
phase not available
BOOL
FALSE
I
x
UNBAL_CUR_I
DR 130: Phase unbalance current
REAL
0.0
I
x
UNBAL_CUR_I_QC
Quality code of UNBAL_CUR_I
BYTE
0
I
UNBAL_CUR_I_OFF
DR 130: Phase unbalance current OFF
BOOL
FALSE
I
x
UNBAL_CUR_I_NA
DR 130: Phase unbalance current not
available
BOOL
FALSE
I
x
T_UNBAL_CUR_I
DR 130: Delay time for phase unbalance
current
REAL
0.0
I
x
T_UNBAL_CUR_I_QC
Quality code of T_UNBAL_CUR_I
BYTE
0
I
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
35
I/O (parameter)
Comment
Data type
Default
Type
OCM
T_UNBAL_CUR_I_OFF
DR 130: Delay time for phase unbalance
current OFF
BOOL
FALSE
I
x
T_UNBAL_CUR_I_NA
DR 130: Delay time for phase unbalance
current not available
BOOL
FALSE
I
x
T_CUR_DEM_I
DR 130: Delay time for demand of the
current
REAL
0.0
I
x
T_CUR_DEM_I_QC
Quality code of T_CUR_DEM_I
BYTE
0
I
T_CUR_DEM_I_OFF
DR 130: Delay time for demand of the
current OFF
BOOL
FALSE
I
x
T_CUR_DEM_I_NA
DR 130: Delay time for demand of the
current not available
BOOL
FALSE
I
x
UNDER_VOLT_I
DR 130: Under voltage
REAL
0.0
I
x
UNDER_VOLT_I_QC
Quality code of UNDER_VOLT_I
BYTE
0
I
UNDER_VOLT_I_OFF
DR 130: Under voltage OFF
BOOL
FALSE
I
x
UNDER_VOLT_I_NA
DR 130: Under voltage not available
BOOL
FALSE
I
x
T_UNDER_VOLT_I
DR 130: Delay time for under voltage
REAL
0.0
I
x
T_UNDER_VOLT_I_QC
Quality code of T_UNDER_VOLT_I
BYTE
0
I
T_UNDER_VOLT_I_OFF
DR 130: Delay time for under voltage OFF
BOOL
FALSE
I
x
T_UNDER_VOLT_I_NA
DR 130: Delay time for under voltage not
available
BOOL
FALSE
I
x
UNBAL_VOLT_I
DR 130: Phase unbalance voltage
REAL
0.0
I
x
UNBAL_VOLT_I_QC
Quality code of UNBAL_VOLT_I
BYTE
0
I
UNBAL_VOLT_I_OFF
DR 130: Phase unbalance voltage OFF
BOOL
FALSE
I
x
UNBAL_VOLT_I_NA
DR 130: Phase unbalance voltage not
available
BOOL
FALSE
I
x
T_UNBAL_VOLT_I
DR 130: Delay time for phase unbalance
voltage
REAL
0.0
I
x
T_UNBAL_VOLT_I_QC
Quality code of T_UNBAL_VOLT_I
BYTE
0
I
T_UNBAL_VOLT_I_OFF
DR 130: Delay time for phase unbalance
voltage OFF
BOOL
FALSE
I
x
T_UNBAL_VOLT_I_NA
DR 130: Delay time for phase unbalance
voltage not available
BOOL
FALSE
I
x
OVER_VOLT_I
DR 130: Over voltage
REAL
0.0
I
x
OVER_VOLT_I_QC
Quality code of OVER_VOLT_I
BYTE
0
I
OVER_VOLT_I_OFF
DR 130: Over voltage OFF
BOOL
FALSE
I
x
OVER_VOLT_I_NA
DR 130: Over voltage not available
BOOL
FALSE
I
x
T_OVER_VOLT_I
DR 130: Delay time for over voltage
REAL
0.0
I
x
T_OVER_VOLT_I_QC
Quality code of T_OVER_VOLT_I
BYTE
0
I
T_OVER_VOLT_I_OFF
DR 130: Delay time for over voltage OFF
BOOL
FALSE
I
x
T_OVER_VOLT_I_NA
DR 130: Delay time for over voltage not
available
BOOL
FALSE
I
x
RD_DR69
Read data record 69 (status of the
modules)
BOOL
FALSE
IO
x
RD_DR91
Read data record 91 (statistic and
maintenance)
BOOL
FALSE
IO
x
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
36
Function Manual, 11/2008, A5E02316914A-01
I/O (parameter)
Comment
Data type
Default
Type
OCM
RD_DR92
Read data record 92 (diagnostics)
BOOL
FALSE
IO
x
RD_DR128
Read data record 128 (metering and ext.
protective function)
BOOL
FALSE
IO
x
RD_DR129
Read data record 129 (protective function)
BOOL
FALSE
IO
x
RD_DR130
Read data record 130 (setpoints)
BOOL
FALSE
IO
x
WR_DR130
Write data record 130 (setpoints)
BOOL
FALSE
IO
x
AUT_ON_OP
Operator input: Mode 1 = AUTO,
0 = MANUAL
BOOL
FALSE
IO
x
AUX_PR01
Auxiliary value 01
ANY
IO
AUX_PR02
Auxiliary value 02
ANY
IO
AUX_PR03
Auxiliary value 03
ANY
IO
AUX_PR04
Auxiliary value 04
ANY
IO
AUX_PR05
Auxiliary value 05
ANY
IO
AUX_PR06
Auxiliary value 06
ANY
IO
AUX_PR07
Auxiliary value 07
ANY
IO
AUX_PR08
Auxiliary value 08
ANY
IO
AUX_PR09
Auxiliary value 09
ANY
IO
AUX_PR10
Auxiliary value 10
ANY
IO
MAN_OFF
Operator input: Switch off (open the main
contacts)
BOOL
FALSE
IO
x
MAN_ON
Operator input: Switch on (close the main
contacts)
BOOL
FALSE
IO
x
RESET
Operator input trip reset
BOOL
FALSE
IO
x
RES_MONERR
Operator input reset monitoring error
BOOL
FALSE
IO
x
ACK_TRIP
A current trip is acknowledged and reset
BOOL
FALSE
IO
x
DEL_TRIP
Delete trip and event log
BOOL
FALSE
IO
x
R_VAL_MEM
Reset all min./max. value memories
(except temperatures)
BOOL
FALSE
IO
x
R_TEMP
Reset min./max. temperatures
BOOL
FALSE
IO
x
R_MAINT
Reset all resettable maintenance
information and counters
BOOL
FALSE
IO
x
MAINT
1 = Maintenance mode
BOOL
FALSE
IO
x
QERR
1 = Error
BOOL
FALSE
O
x
QMON_ERR
1 = Monitoring error
BOOL
FALSE
O
x
QBAD
1 = Bad process value
BOOL
FALSE
O
x
QMSG_SUP
1 = Message suppression active
BOOL
FALSE
O
x
QMSG_ERR
1 = Message error
BOOL
FALSE
O
QMANOP
1 = Operator enabled for MANUAL
BOOL
FALSE
O
x
QDIAG_REQ
1 = Read diagnostic information
BOOL
FALSE
O
QAUTOP
1 = Operator enabled for AUTO
BOOL
FALSE
O
x
QOFF_OP
1 = Operator enabled for "OFF"
BOOL
FALSE
O
x
QON_OP
1 = Operator enabled for "ON"
BOOL
FALSE
O
x
QRES_OP
1 = Operator enabled for "RESET"
BOOL
FALSE
O
x
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
37
I/O (parameter)
Comment
Data type
Default
Type
OCM
QDR_OP
1 = Operator enabled for data record
actions
BOOL
FALSE
O
x
QOP_ERR
1 = Operator error
BOOL
FALSE
O
QMAN_AUT
1 = AUTO, 0 = MANUAL mode
BOOL
FALSE
O
x
MSG_STAT1
Message block 1: STATUS output
WORD
0
O
MSG_STAT2
Message block 2: STATUS output
WORD
0
O
MSG_ACK1
Message block 1: ACK_STATE output
WORD
0
O
MSG_ACK2
Message block 2: ACK_STATE output
WORD
0
O
QERR_WR
1 = An error occurred during writing DRs
BOOL
FALSE
O
QERR_RD
1 = An error occurred during reading DRs
BOOL
FALSE
O
QWR_STAT
Status of DR writing
WORD
0
O
QRD_STAT
Status of DR reading
WORD
0
O
STATUS
Binary status information
WORD
0
O
STATUS_QC
Quality code of STATUS
BYTE
0
O
CUR_L1
Current in phase 1
REAL
0.0
O
x
CUR_L1_QC
Quality code of CUR_L1
BYTE
0
O
CUR_L2
Current in phase 2
REAL
0.0
O
x
CUR_L2_QC
Quality code of CUR_L2
BYTE
0
O
CUR_L3
Current in phase 3
REAL
0.0
O
x
CUR_L3_QC
Quality code of CUR_L3
BYTE
0
O
CUR_MAX
Current max. L1, L2, L3
REAL
0.0
O
x
CUR_MAX_QC
Quality code of CUR_MAX
BYTE
0
O
CUR_N
Current in phase N (trip unit)
REAL
0.0
O
x
CUR_N_QC
Quality code of CUR_N
BYTE
0
O
U_L1_L2
Voltage line-to-line L1-L2 (A-B)
REAL
0.0
O
x
U_L1_L2_QC
Quality code of U_L1_L2
BYTE
0
O
U_L2_L3
Voltage line-to-line L2-L3 (B-C)
REAL
0.0
O
x
U_L2_L3_QC
Quality code of U_L2_L3
BYTE
0
O
U_L3_L1
Voltage line-to-line L3-L1 (C-A)
REAL
0.0
O
x
U_L3_L1_QC
Quality code of U_L3_L1
BYTE
0
O
U_L1_N
Voltage star point L1-N (A-N)
REAL
0.0
O
x
U_L1_N_QC
Quality code of U_L1_N
BYTE
0
O
U_L2_N
Voltage star point L2-N (B-N)
REAL
0.0
O
x
U_L2_N_QC
Quality code of U_L2_N
BYTE
0
O
U_L3_N
Voltage star point L3-N (C-N)
REAL
0.0
O
x
U_L3_N_QC
Quality code of U_L3_N
BYTE
0
O
PF_AVG
Power factor average
REAL
0.0
O
x
PF_AVG_QC
Quality code of PF_AVG
BYTE
0
O
ACT_W
Active energy in normal direction
REAL
0.0
O
x
ACT_W_QC
Quality code of ACT_W
BYTE
0
O
KVA_TOT
Apparent power total
REAL
0.0
O
x
KVA_TOT_QC
Quality code of KVA_TOT
BYTE
0
O
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
38
Function Manual, 11/2008, A5E02316914A-01
I/O (parameter)
Comment
Data type
Default
Type
OCM
POS_CB
Position of circuit breaker
BYTE
0
O
x
QDISCON
1 = Disconnected
BOOL
FALSE
O
x
QOP_POS
1 = Operating position
BOOL
FALSE
O
QTEST_POS
1 = Test position
BOOL
FALSE
O
QNO_CB
1 = Circuit breaker not present
BOOL
FALSE
O
x
ST_CB
Status of circuit breaker
BYTE
0
O
x
QNOT_RDY
1 = Circuit breaker not ready
BOOL
FALSE
O
QOFF
1 = Main contacts disconnected
BOOL
FALSE
O
QON
1 = Main contacts closed
BOOL
FALSE
O
QTRIP
1 = Circuit breaker has tripped
BOOL
FALSE
O
QLOC_OFF
1 = Local turn off of circuit breaker
BOOL
FALSE
O
x
QRDY_ON
1 = Ready to switch on
BOOL
FALSE
O
QUNV_REL
1 = Voltage applied to undervoltage
release
BOOL
FALSE
O
QSPR_CHAR
1 = Storage spring is charged
BOOL
FALSE
O
QOVLD_WRN
1 = Overload warning present
BOOL
FALSE
O
QSP_EXCEED
1 = An activated setpoint value has been
exceeded
BOOL
FALSE
O
QWRN
1 = A warning signal is currently present
BOOL
FALSE
O
QWR_PROT
1 = Write operations are prohibited
BOOL
FALSE
O
QFREE_COM15
1 = Status of the free user input on the
COM15 module
BOOL
FALSE
O
LST_TRIP
Reason for last trip
BYTE
0
O
QTR_OVLD
1 = Overload tripping (L)
BOOL
FALSE
O
QTR_ISC
1 = Instantaneous short-circuit (I)
BOOL
FALSE
O
QTR_STD_C
1 = Short-time-delay short-circuit (S)
BOOL
FALSE
O
QTR_GF
1 = Ground fault (G)
BOOL
FALSE
O
QTR_EXT_F
1 = Trip as a result of extended protection
function
BOOL
FALSE
O
QTR_OVLD_N
1 = Overload in neutral conductor
BOOL
FALSE
O
QLD_SHED
1 = Load shedding warning
BOOL
FALSE
O
E_TIME_SYC
1 = Error time synchronization
BOOL
FALSE
O
STON_GFNA
Short time on / Ground fault off
BOOL
FALSE
O
x
STON_GFOFF_QC
Quality code of STON_GFOFF
BYTE
0
O
STON_GFOFF_NA
Short time on / Ground fault off not
available
BOOL
FALSE
O
x
STON_GFOFF_STOFF_GFON
Short time off / Ground fault off
BOOL
FALSE
O
x
STOFF_GFON_QC
Quality code of STOFF_GFON
BYTE
0
O
STOFF_GFON_NA
Short time off / Ground fault on not
available
BOOL
FALSE
O
x
N_ACT_LD
DR 91: Number of switch actions under
load
WORD
0
O
x
N_ACT_LD_QC
Quality code of N_ACT_LD
BYTE
0
O
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
39
I/O (parameter)
Comment
Data type
Default
Type
OCM
N_ACT_LD_NA
DR 91: Number of switch actions under
load not available
BOOL
FALSE
O
x
N_ACT_TRP
DR 91: Number of switch actions caused
by a trip
WORD
0
O
x
N_ACT_TRP_QC
Quality code of N_ACT_TRP
BYTE
0
O
N_ACT_TRP_NA
DR 91: Number of switch actions caused
by a trip not available
BOOL
FALSE
O
x
N_ACT_CC
DR 91: Number of switch actions
(complete cycle on/off)
WORD
0
O
x
N_ACT_CC_QC
Quality code of N_ACT_CC
BYTE
0
O
N_ACT_CC_NA
DR 91: Number of switch actions
(complete cycle on/off) not available
BOOL
FALSE
O
x
OP_HOURS
DR 91: Operating hours (breaker on and
current > 0)
DWORD
0
O
x
OP_HOURS_QC
Quality code of OP_HOURS
BYTE
0
O
OP_HOURS_NA
DR 91: Operating hours (breaker on and
current > 0) not available
BOOL
FALSE
O
x
LAST_CHG
DR 91: Date of the last parameter change
DATE_AND_
TIME
DT#1990-
01-01-
0:0:0.0
O
LAST_CHG_QC
Quality code of LAST_CHG
BYTE
0
O
LAST_CHG_NA
DR 91: Date of the last parameter change
not available
BOOL
FALSE
O
N_SC_TRP
DR 91: Number of short circuit trips (SI)
WORD
0
O
x
N_SC_TRP_QC
Quality code of N_SC_TRP
BYTE
0
O
N_SC_TRP_NA
DR 91: Number of short circuit trips (SI)
not available
BOOL
FALSE
O
x
N_OVL_TRP
DR 91: Number of overload trips (L)
WORD
0
O
x
N_OVL_TRP_QC
Quality code of N_OVL_TRP
BYTE
0
O
N_OVL_TRP_OFF
DR 91: Number of overload trips (L) OFF
BOOL
FALSE
O
x
N_OVL_TRP_NA
DR 91: Number of overload trips (L) not
available
BOOL
FALSE
O
x
N_EF_TRP
DR 91: Number of earth fault trips (G)
WORD
0
O
x
N_EF_TRP_QC
Quality code of N_EF_TRP
BYTE
0
O
N_EF_TRP_NA
DR 91: Number of earth fault trips (G) not
available
BOOL
FALSE
O
x
S_I2T_L1
DR 91: Sum of I2T-values L1
REAL
0.0
O
x
S_I2T_L1_QC
Quality code of S_I2T_L1
BYTE
0
O
S_I2T_L1_NA
DR 91: Sum of I2T-values L1 not available
BOOL
FALSE
O
x
S_I2T_L2
DR 91: Sum of I2T-values L2
REAL
0.0
O
x
S_I2T_L2_QC
Quality code of S_I2T_L2
BYTE
0
O
S_I2T_L2_NA
DR 91: Sum of I2T-values L2 not available
BOOL
FALSE
O
x
S_I2T_L3
DR 91: Sum of I2T-values L3
REAL
0.0
O
x
S_I2T_L3_QC
Quality code of S_I2T_L3
BYTE
0
O
S_I2T_L3_NA
DR 91: Sum of I2T-values L3 not available
BOOL
FALSE
O
x
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
40
Function Manual, 11/2008, A5E02316914A-01
I/O (parameter)
Comment
Data type
Default
Type
OCM
S_I2T_N
DR 91: Sum of I2T-values N
REAL
0.0
O
x
S_I2T_N_QC
Quality code of S_I2T_N
BYTE
0
O
S_I2T_N_NA
DR 91: Sum of I2T-values N not available
BOOL
FALSE
O
x
MAINT_MC
DR 91: Maintenance information for the
main contacts
BYTE
0
O
x
MAINT_MC_QC
Quality code of MAINT_MC
BYTE
0
O
MAINT_MC_NA
DR 91: Maintenance information for the
main contacts not available
BOOL
FALSE
O
x
CON_MOD
DR 91: Connected CubicleBus modules
DWORD
0
O
x
CON_MOD_QC
Quality code of CON_MOD
BYTE
0
O
CON_MOD_NA
DR 91: Connected CubicleBus modules
Not Available
BOOL
FALSE
O
x
DIAG_WRN
DR 92: Active warnings
WORD
0
O
DIAG_WRN_QC
Quality code of DIAG_WRN
BYTE
0
O
DIAG_TRIP
DR 92: Trips of the extended protective
function
WORD
0
O
DIAG_TRIP_QC
Quality code of DIAG_TRIP
BYTE
0
O
DIAG_SP
DR 92: Setpoints warnings
DWORD
0
O
DIAG_SP_QC
Quality code of DIAG_SP
BYTE
0
O
WRN_NO1
Warning number 1
INT
0
O
x
WRN_NO2
Warning number 2
INT
0
O
x
WRN_NO3
Warning number 3
INT
0
O
x
WRN_NO4
Warning number 4
INT
0
O
x
WRN_NO5
Warning number 5
INT
0
O
x
WRN_NO6
Warning number 6
INT
0
O
x
WRN_NO7
Warning number 7
INT
0
O
x
WRN_NO8
Warning number 8
INT
0
O
x
TRIP_NO1
Trip number 1
INT
0
O
x
TRIP_NO2
Trip number 2
INT
0
O
x
TRIP_NO3
Trip number 3
INT
0
O
x
TRIP_NO4
Trip number 4
INT
0
O
x
TRIP_NO5
Trip number 5
INT
0
O
x
TRIP_NO6
Trip number 6
INT
0
O
x
TRIP_NO7
Trip number 7
INT
0
O
x
TRIP_NO8
Trip number 8
INT
0
O
x
SP_NO1
Setpoint warning number 1
INT
0
O
x
SP_NO2
Setpoint warning number 2
INT
0
O
x
SP_NO3
Setpoint warning number 3
INT
0
O
x
SP_NO4
Setpoint warning number 4
INT
0
O
x
SP_NO5
Setpoint warning number 5
INT
0
O
x
SP_NO6
Setpoint warning number 6
INT
0
O
x
SP_NO7
Setpoint warning number 7
INT
0
O
x
SP_NO8
Setpoint warning number 8
INT
0
O
x
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
41
I/O (parameter)
Comment
Data type
Default
Type
OCM
CUR_UNBAL
DR 94: Phase unbalanced current (in %)
REAL
0.0
O
x
CUR_UNBAL_QC
Quality code of CUR_UNBAL
BYTE
0
O
CUR_UNBAL_NA
DR 94: Phase unbalanced current (in %)
not available
BOOL
FALSE
O
x
CUR_DEM3
DR 94: Demand current 3-phases
REAL
0.0
O
x
CUR_DEM3_QC
Quality code of CUR_DEM3
BYTE
0
O
CUR_DEM3_NA
DR 94: Demand current 3-phases not
available
BOOL
FALSE
O
x
CUR_DEM_L1
DR 94: Demand current L1
REAL
0.0
O
x
CUR_DEM_L1_QC
Quality code of CUR_DEM_L1
BYTE
0
O
CUR_DEM_L1_NA
DR 94: Demand current L1 not available
BOOL
FALSE
O
x
CUR_DEM_L2
DR 94: Demand current L2
REAL
0.0
O
x
CUR_DEM_L2_QC
Quality code of CUR_DEM_L2
BYTE
0
O
CUR_DEM_L2_NA
DR 94: Demand current L2 not available
BOOL
FALSE
O
x
CUR_DEM_L3
DR 94: Demand current L3
REAL
0.0
O
x
CUR_DEM_L3_QC
Quality code of CUR_DEM_L3
BYTE
0
O
CUR_DEM_L3_NA
DR 94: Demand current L3 not available
BOOL
FALSE
O
x
CUR_L1_DR94
DR 94: Current in phase 1
REAL
0.0
O
x
CUR_L1_DR94_QC
Quality code of CUR_L1_DR94
BYTE
0
O
CUR_L1_DR94_NA
DR 94: Current in phase 1 not available
BOOL
FALSE
O
x
CUR_L2_DR94
DR 94: Current in phase 2
REAL
0.0
O
x
CUR_L2_DR94_QC
Quality code of CUR_L2_DR94
BYTE
0
O
CUR_L2_DR94_NA
DR 94: Current in phase 2 not available
BOOL
FALSE
O
x
CUR_L3_DR94
DR 94: Current in phase 3
REAL
0.0
O
x
CUR_L3_DR94_QC
Quality code of CUR_L3_DR94
BYTE
0
O
CUR_L3_DR94_NA
DR 94: Current in phase 3 not available
BOOL
FALSE
O
x
CUR_DEM3PH
DR 94: Current demand over three phases REAL
0.0
O
x
CUR_DEM3PH_QC
Quality code of CUR_DEM3PH
BYTE
0
O
CUR_DEM3PH_NA
DR 94: Current demand over three phases
not available
BOOL
FALSE
O
x
CUR_N_DR94
DR 94: Current N-phase
REAL
0.0
O
x
CUR_N_DR94_QC
Quality code of CUR_N_DR94
BYTE
0
O
CUR_N_DR94_NA
DR 94: Current N-phase not available
BOOL
FALSE
O
x
CUR_EARTH_F
DR 94: Earth fault current
REAL
0.0
O
x
CUR_EARTH_F_QC
Quality code of CUR_EARTH_F
BYTE
0
O
CUR_EARTH_F_NA
DR 94: Earth fault current not available
BOOL
FALSE
O
x
VOLT_UNBAL
DR 94: Phase unbalanced voltage (in %)
REAL
0.0
O
x
VOLT_UNBAL_QC
Quality code of VOLT_UNBAL
BYTE
0
O
VOLT_UNBAL_NA
DR 94: Phase unbalanced voltage (in %)
not available
BOOL
FALSE
O
x
VOLT_L1L2
DR 94: Delta voltage between phase L1
and L2
REAL
0.0
O
x
VOLT_L1L2_QC
Quality code of VOLT_L1L2
BYTE
0
O
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
42
Function Manual, 11/2008, A5E02316914A-01
I/O (parameter)
Comment
Data type
Default
Type
OCM
VOLT_L1L2_NA
DR 94: Delta voltage between phase L1
and L2 not available
BOOL
FALSE
O
x
VOLT_L2L3
DR 94: Delta voltage between phase L2
and L3
REAL
0.0
O
x
VOLT_L2L3_QC
Quality code of VOLT_L2L3
BYTE
0
O
VOLT_L2L3_NA
DR 94: Delta voltage between phase L2
and L3 not available
BOOL
FALSE
O
x
VOLT_L3L1
DR 94: Delta voltage between phase L3
and L1
REAL
0.0
O
x
VOLT_L3L1_QC
Quality code of VOLT_L3L1
BYTE
0
O
VOLT_L3L1_NA
DR 94: Delta voltage between phase L3
and L1 not available
BOOL
FALSE
O
x
VOLT_L1N
DR 94: Star voltage phase L1
REAL
0.0
O
x
VOLT_L1N_QC
Quality code of VOLT_L1N
BYTE
0
O
VOLT_L1N_NA
DR 94: Star voltage phase L1 not available
BOOL
FALSE
O
x
VOLT_L2N
DR 94: Star voltage phase L2
REAL
0.0
O
x
VOLT_L2N_QC
Quality code of VOLT_L2N
BYTE
0
O
VOLT_L2N_NA
DR 94: Star voltage phase L2 not available
BOOL
FALSE
O
x
VOLT_L3N
DR 94: Star voltage phase L3
REAL
0.0
O
x
VOLT_L3N_QC
Quality code of VOLT_L3N
BYTE
0
O
VOLT_L3N_NA
DR 94: Star voltage phase L3 not available
BOOL
FALSE
O
x
VOLT_DEM_D
DR 94: Demand of the delta voltage
REAL
0.0
O
x
VOLT_DEM_D_QC
Quality code of VOLT_DEM_D
BYTE
0
O
VOLT_DEM_D_NA
DR 94: Demand of the delta voltage not
available
BOOL
FALSE
O
x
VOLT_DEM_S
DR 94: Demand of the star voltage
REAL
0.0
O
x
VOLT_DEM_S_QC
Quality code of VOLT_DEM_S
BYTE
0
O
VOLT_DEM_S_NA
DR 94: Demand of the star voltage not
available
BOOL
FALSE
O
x
SUM_AP
DR 94: Sum of apparent power
REAL
0.0
O
x
SUM_AP_QC
Quality code of SUM_AP
BYTE
0
O
SUM_AP_NA
DR 94: Sum of apparent power not
available
BOOL
FALSE
O
x
SUM_RP
DR 94: Sum of real power
REAL
0.0
O
x
SUM_RP_QC
Quality code of SUM_RP
BYTE
0
O
SUM_RP_NA
DR 94: Sum of real power not available
BOOL
FALSE
O
x
RP_L1
DR 94: Real power in phase L1
REAL
0.0
O
x
RP_L1_QC
Quality code of RP_L1
BYTE
0
O
RP_L1_NA
DR 94: Real power in phase L1 not
available
BOOL
FALSE
O
x
RP_L2
DR 94: Real power in phase L2
REAL
0.0
O
x
RP_L2_QC
Quality code of RP_L2
BYTE
0
O
RP_L2_NA
DR 94: Real power in phase L2 not
available
BOOL
FALSE
O
x
RP_L3
DR 94: Real power in phase L3
REAL
0.0
O
x
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
43
I/O (parameter)
Comment
Data type
Default
Type
OCM
RP_L3_QC
Quality code of RP_L3
BYTE
0
O
RP_L3_NA
DR 94: Real power in phase L3 not
available
BOOL
FALSE
O
x
SUM_RAP
DR 94: Sum of reactive power
REAL
0.0
O
x
SUM_RAP_QC
Quality code of SUM_RAP
BYTE
0
O
SUM_RAP_NA
DR 94: Sum of reactive power not
available
BOOL
FALSE
O
x
DEM_RP3
DR 94: Demand of the real power 3-
phases
REAL
0.0
O
x
DEM_RP3_QC
Quality code of DEM_RP3
BYTE
0
O
DEM_RP3_NA
DR 94: Demand of the real power 3-
phases not available
BOOL
FALSE
O
x
DEM_RP_L1
DR 94: Demand of the real power in phase
L1
REAL
0.0
O
x
DEM_RP_L1_QC
Quality code of DEM_RP_L1
BYTE
0
O
DEM_RP_L1_NA
DR 94: Demand of the real power in phase
L1 not available
BOOL
FALSE
O
x
DEM_RP_L2
DR 94: Demand of the real power in phase
L2
REAL
0.0
O
x
DEM_RP_L2_QC
Quality code of DEM_RP_L2
BYTE
0
O
DEM_RP_L2_NA
DR 94: Demand of the real power in phase
L2 not available
BOOL
FALSE
O
x
DEM_RP_L3
DR 94: Demand of the real power in phase
L3
REAL
0.0
O
x
DEM_RP_L3_QC
Quality code of DEM_RP_L3
BYTE
0
O
DEM_RP_L3_NA
DR 94: Demand of the real power in phase
L3 not available
BOOL
FALSE
O
x
DEM_AP3
DR 94: Demand of the apparent power 3-
phases
REAL
0.0
O
x
DEM_AP3_QC
Quality code of DEM_AP3
BYTE
0
O
DEM_AP3_NA
DR 94: Demand of the apparent power 3-
phases not available
BOOL
FALSE
O
x
AP_L1
DR 94: Apparent power in phase L1
REAL
0.0
O
x
AP_L1_QC
Quality code of AP_L1
BYTE
0
O
AP_L1_NA
DR 94: Apparent power in phase L1 not
available
BOOL
FALSE
O
x
AP_L2
DR 94: Apparent power in phase L2
REAL
0.0
O
x
AP_L2_QC
Quality code of AP_L2
BYTE
0
O
AP_L2_NA
DR 94: Apparent power in phase L2 not
available
BOOL
FALSE
O
x
AP_L3
DR 94: Apparent power in phase L3
REAL
0.0
O
x
AP_L3_QC
Quality code of AP_L3
BYTE
0
O
AP_L3_NA
DR 94: Apparent power in phase L3 not
available
BOOL
FALSE
O
x
DEM_AP_L1
DR 94: Demand of the apparent power in
phase L1
REAL
0.0
O
x
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
44
Function Manual, 11/2008, A5E02316914A-01
I/O (parameter)
Comment
Data type
Default
Type
OCM
DEM_AP_L1_QC
Quality code of DEM_AP_L1
BYTE
0
O
DEM_AP_L1_NA
DR 94: Demand of the apparent power in
phase L1 not available
BOOL
FALSE
O
x
DEM_AP_L2
DR 94: Demand of the apparent power in
phase L2
REAL
0.0
O
x
DEM_AP_L2_QC
Quality code of DEM_AP_L2
BYTE
0
O
DEM_AP_L2_NA
DR 94: Demand of the apparent power in
phase L2 not available
BOOL
FALSE
O
x
DEM_AP_L3
DR 94: Demand of the apparent power in
phase L3
REAL
0.0
O
x
DEM_AP_L3_QC
Quality code of DEM_AP_L3
BYTE
0
O
DEM_AP_L3_NA
DR 94: Demand of the apparent power in
phase L3 not available
BOOL
FALSE
O
x
DEM_RAP3
DR 94: Demand of the reactive power 3-
phases
REAL
0.0
O
x
DEM_RAP3_QC
Quality code of DEM_RAP3
BYTE
0
O
DEM_RAP3_NA
DR 94: Demand of the reactive power 3-
phases not available
BOOL
FALSE
O
x
RAP_L1
DR 94: Reactive power in phase L1
REAL
0.0
O
x
RAP_L1_QC
Quality code of RAP_L1
BYTE
0
O
RAP_L1_NA
DR 94: Reactive power in phase L1 not
available
BOOL
FALSE
O
x
RAP_L2
DR 94: Reactive power in phase L2
REAL
0.0
O
x
RAP_L2_QC
Quality code of RAP_L2
BYTE
0
O
RAP_L2_NA
DR 94: Reactive power in phase L2 not
available
BOOL
FALSE
O
x
RAP_L3
DR 94: Reactive power in phase L3
REAL
0.0
O
x
RAP_L3_QC
Quality code of RAP_L3
BYTE
0
O
RAP_L3_NA
DR 94: Reactive power in phase L3 not
available
BOOL
FALSE
O
x
RE_NORM
DR 94: Real energy in normal direction
[MWh]
REAL
0.0
O
x
RE_NORM_QC
Quality code of RE_NORM
BYTE
0
O
RE_NORM_NA
DR 94: Real energy in normal direction
[MWh] not available
BOOL
FALSE
O
x
RE_REV
DR 94: Real energy in reverse direction
[MWh]
REAL
0.0
O
x
RE_REV_QC
Quality code of RE_REV
BYTE
0
O
RE_REV_NA
DR 94: Real energy in reverse direction
[MWh] not available
BOOL
FALSE
O
x
REC_E_NORM
DR 94: Reactive energy in normal direction
[MVarh]
REAL
0.0
O
x
REC_E_NORM_QC
Quality code of REC_E_NORM
BYTE
0
O
REC_E_NORM_NA
DR 94: Reactive energy in normal direction
[MVarh] not available
BOOL
FALSE
O
x
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
45
I/O (parameter)
Comment
Data type
Default
Type
OCM
REC_E_REV
DR 94: Reactive energy in reverse
direction [MVarh]
REAL
0.0
O
x
REC_E_REV_QC
Quality code of REC_E_REV
BYTE
0
O
REC_E_REV_NA
DR 94: Reactive energy in reverse
direction [MVarh] not available
BOOL
FALSE
O
x
PF_DEM
DR 94: Demand of the power factor
REAL
0.0
O
x
PF_DEM_QC
Quality code of PF_DEM
BYTE
0
O
PF_DEM_NA
DR 94: Demand of the power factor not
available
BOOL
FALSE
O
x
PF_L1
DR 94: Power factor in phase L1
REAL
0.0
O
x
PF_L1_QC
Quality code of PF_L1
BYTE
0
O
PF_L1_NA
DR 94: Power factor in phase L1 not
available
BOOL
FALSE
O
x
PF_L2
DR 94: Power factor in phase L2
REAL
0.0
O
x
PF_L2_QC
Quality code of PF_L2
BYTE
0
O
PF_L2_NA
DR 94: Power factor in phase L2 not
available
BOOL
FALSE
O
x
PF_L3
DR 94: Power factor in phase L3
REAL
0.0
O
x
PF_L3_QC
Quality code of PF_L3
BYTE
0
O
PF_L3_NA
DR 94: Power factor in phase L3 not
available
BOOL
FALSE
O
x
FRQ
DR 94: Frequency
REAL
0.0
O
x
FRQ_QC
Quality code of FRQ
BYTE
0
O
FRQ_NA
DR 94: Frequency not available
BOOL
FALSE
O
x
THD_CUR94
DR 94: THD of the current
REAL
0.0
O
x
THD_CUR94_QC
Quality code of THD_CUR94
BYTE
0
O
THD_CUR94_NA
DR 94: THD of the current not available
BOOL
FALSE
O
x
THD_VOLT
DR 94: THD of the voltage
REAL
0.0
O
x
THD_VOLT_QC
Quality code of THD_VOLT
BYTE
0
O
THD_VOLT_NA
DR 94: THD of the voltage not available
BOOL
FALSE
O
x
FORM_F
DR 94: Form factor
REAL
0.0
O
x
FORM_F_QC
Quality code of FORM_F
BYTE
0
O
FORM_F_NA
DR 94: Form factor not available
BOOL
FALSE
O
x
CREST_F
DR 94: Crest factor
REAL
0.0
O
x
CREST_F_QC
Quality code of CREST_F
BYTE
0
O
CREST_F_NA
DR 94: Crest factor not available
BOOL
FALSE
O
x
TMP_CUB
DR 94: Temperature in the cubicle (det. in
the COM15)
REAL
0.0
O
x
TMP_CUB_QC
Quality code of TMP_CUB
BYTE
0
O
TMP_CUB_NA
DR 94: Temperature in the cubicle (det. in
the COM15) not available
BOOL
FALSE
O
x
TMP_MSAE
DR 94: Temperature in the circuit breaker
(det. in BSS)
REAL
0.0
O
x
TMP_MSAE_QC
Quality code of TMP_MSAE
BYTE
0
O
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
46
Function Manual, 11/2008, A5E02316914A-01
I/O (parameter)
Comment
Data type
Default
Type
OCM
TMP_MSAE_NA
DR 94: Temperature in the circuit breaker
(det. in BSS) not available
BOOL
FALSE
O
x
C_VT_YD
DR128: Primary connection of the voltage
transformer Ypsilon or Delta
BOOL
FALSE
O
x
C_VT_YD_QC
Quality code of C_VT_YD
BYTE
0
O
C_VT_YD_OFF
DR 128: Primary connection of the voltage
transformer Ypsilon or Delta OFF
BOOL
FALSE
O
x
C_VT_YD_NA
DR 128: Primary connection of the voltage
transformer Ypsilon or Delta not available
BOOL
FALSE
O
x
T_VOLT_T
DR 128: Typ voltage transformer
BYTE
0
O
x
T_VOLT_T_QC
Quality code of T_VOLT_T
BYTE
0
O
T_VOLT_T_OFF
DR 128: Typ voltage transformer OFF
BOOL
FALSE
O
x
T_VOLT_T_NA
DR 128: Typ voltage transformer not
available
BOOL
FALSE
O
x
ROV_PH_PH
DR 128: Rated operational voltage
(Phase2Phase)
REAL
0.0
O
x
ROV_PH_PH_QC
Quality code of ROV_PH_PH
BYTE
0
O
ROV_PH_PH_OFF
DR 128: Rated operational voltage
(Phase2Phase) OFF
BOOL
FALSE
O
x
ROV_PH_PH_NA
DR 128: Rated operational voltage
(Phase2Phase) not available
BOOL
FALSE
O
x
SEC_VOLT
DR 128: Secondary voltage of the voltage
transformer
REAL
0.0
O
x
SEC_VOLT_QC
Quality code of SEC_VOLT
BYTE
0
O
SEC_VOLT_OFF
DR 128: Secondary voltage of the voltage
transformer OFF
BOOL
FALSE
O
x
SEC_VOLT_NA
DR 128: Secondary voltage of the voltage
transformer not available
BOOL
FALSE
O
x
PER_DEM
DR 128: Length of period for demand
calculating
REAL
0.0
O
x
PER_DEM_QC
Quality code of PER_DEM
BYTE
0
O
PER_DEM_OFF
DR 128: Length of period for demand
calculating OFF
BOOL
FALSE
O
x
PER_DEM_NA
DR 128: Length of period for demand
calculating not available
BOOL
FALSE
O
x
SUB_PER
DR 128: No. of sub periods for calculating
demands
REAL
0.0
O
x
SUB_PER_QC
Quality code of SUB_PER
BYTE
0
O
SUB_PER_OFF
DR 128: No. of sub periods for calculating
demands OFF
BOOL
FALSE
O
x
SUB_PER_NA
DR 128: No. of sub periods for calculating
demands not available
BOOL
FALSE
O
x
CUR_TRNS_LIM
DR 128: Current transmission limit; below
this all currents will be set to 0
REAL
0.0
O
x
CUR_TRNS_LIM_QC
Quality code of CUR_TRNS_LIM
BYTE
0
O
CUR_TRNS_LIM_OFF
DR 128: Current transmission limit; below
this all currents will be set to 0 OFF
BOOL
FALSE
O
x
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
47
I/O (parameter)
Comment
Data type
Default
Type
OCM
CUR_TRNS_LIM_NA
DR 128: Current transmission limit; below
this all currents will be set to 0 not
available
BOOL
FALSE
O
x
RP_NORM
DR 128: Real power in normal direction
REAL
0.0
O
x
RP_NORM_QC
Quality code of RP_NORM
BYTE
0
O
RP_NORM_OFF
DR 128: Real power in normal direction
OFF
BOOL
FALSE
O
x
RP_NORM_NA
DR 128: Real power in normal direction
not available
BOOL
FALSE
O
x
RP_REV
DR 128: Real power in reverse direction
REAL
0.0
O
x
RP_REV_QC
Quality code of RP_REV
BYTE
0
O
RP_REV_OFF
DR 128: Real power in reverse direction
OFF
BOOL
FALSE
O
x
RP_REV_NA
DR 128: Real power in reverse direction
not available
BOOL
FALSE
O
x
T_RP_NORM
DR 128: Delay time for real power in
normal direction
REAL
0.0
O
x
T_RP_NORM_QC
Quality code of T_RP_NORM
BYTE
0
O
T_RP_NORM_OFF
DR 128: Delay time for real power in
normal direction OFF
BOOL
FALSE
O
x
T_RP_NORM_NA
DR 128: Delay time for real power in
normal direction not available
BOOL
FALSE
O
x
T_RP_REV
DR 128: Delay time for real power in
reverse direction
REAL
0.0
O
x
T_RP_REV_QC
Quality code of T_RP_REV
BYTE
0
O
T_RP_REV_OFF
DR 128: Delay time for real power in
reverse direction OFF
BOOL
FALSE
O
x
T_RP_REV_NA
DR 128: Delay time for real power in
reverse direction not available
BOOL
FALSE
O
x
NORM_DIR
DR 128: Definition of the normal energy
direction
BOOL
FALSE
O
x
NORM_DIR_QC
Quality code of NORM_DIR
BYTE
0
O
NORM_DIR_OFF
DR 128: Definition of the normal energy
direction OFF
BOOL
FALSE
O
x
NORM_DIR_NA
DR 128: Definition of the normal energy
direction not available
BOOL
FALSE
O
x
PH_ROT
DR 128: Phase rotation
BOOL
FALSE
O
x
PH_ROT_QC
Quality code of PH_ROT
BYTE
0
O
PH_ROT_OFF
DR 128: Phase rotation OFF
BOOL
FALSE
O
x
PH_ROT_NA
DR 128: Phase rotation not available
BOOL
FALSE
O
x
UNDER_FRQ
DR 128: Under frequency
REAL
0.0
O
x
UNDER_FRQ_QC
Quality code of UNDER_FRQ
BYTE
0
O
UNDER_FRQ_OFF
DR 128: Under frequency OFF
BOOL
FALSE
O
x
UNDER_FRQ_NA
DR 128: Under frequency not available
BOOL
FALSE
O
x
T_OV_FRQ
DR 128: Delay time for over frequency
REAL
0.0
O
x
T_OV_FRQ_QC
Quality code of T_OV_FRQ
BYTE
0
O
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
48
Function Manual, 11/2008, A5E02316914A-01
I/O (parameter)
Comment
Data type
Default
Type
OCM
T_OV_FRQ_OFF
DR 128: Delay time for over frequency
OFF
BOOL
FALSE
O
x
T_OV_FRQ_NA
DR 128: Delay time for over frequency not
available
BOOL
FALSE
O
x
T_UN_FRQ
DR 128: Delay time for under frequency
REAL
0.0
O
x
T_UN_FRQ_QC
Quality code of T_UN_FRQ
BYTE
0
O
T_UN_FRQ_OFF
DR 128: Delay time for under frequency
OFF
BOOL
FALSE
O
x
T_UN_FRQ_NA
DR 128: Delay time for under frequency
not available
BOOL
FALSE
O
x
OV_FRQ
DR 128: Over frequency
REAL
0.0
O
x
OV_FRQ_QC
Quality code of OV_FRQ
BYTE
0
O
OV_FRQ_OFF
DR 128: Over frequency OFF
BOOL
FALSE
O
x
OV_FRQ_NA
DR 128: Over frequency not available
BOOL
FALSE
O
x
THD_CUR
DR 128: THD of the current
REAL
0.0
O
x
THD_CUR_QC
Quality code of THD_CUR
BYTE
0
O
THD_CUR_OFF
DR 128: THD of the current OFF
BOOL
FALSE
O
x
THD_CUR_NA
DR 128: THD of the current not available
BOOL
FALSE
O
x
T_THD_CUR
DR 128: Delay time for THD of the current
REAL
0.0
O
x
T_THD_CUR_QC
Quality code of T_THD_CUR
BYTE
0
O
T_THD_CUR_OFF
DR 128: Delay time for THD of the current
OFF
BOOL
FALSE
O
x
T_THD_CUR_NA
DR 128: Delay time for THD of the current
not available
BOOL
FALSE
O
x
PU_THD_VOLT
DR 128: Pickup THD voltage
REAL
0.0
O
x
PU_THD_VOLT_QC
Quality code of PU_THD_VOLT
BYTE
0
O
PU_THD_VOLT_OFF
DR 128: Pickup THD voltage OFF
BOOL
FALSE
O
x
PU_THD_VOLT_NA
DR 128: Pickup THD voltage not available
BOOL
FALSE
O
x
T_THD_VOLT
DR 128: Delay time for THD of the voltage
REAL
0.0
O
x
T_THD_VOLT_QC
Quality code of T_THD_VOLT
BYTE
0
O
T_THD_VOLT_OFF
DR 128: Delay time for THD of the voltage
OFF
BOOL
FALSE
O
x
T_THD_VOLT_NA
DR 128: Delay time for THD of the voltage
not available
BOOL
FALSE
O
x
PH_UNBAL_VOLT
DR 128: Phase unbalanced voltage
REAL
0.0
O
x
PH_UNBAL_VOLT_QC
Quality code of PH_UNBAL_VOLT
BYTE
0
O
PH_UNBAL_VOLT_OFF
DR 128: Phase unbalanced voltage OFF
BOOL
FALSE
O
x
PH_UNBAL_VOLT_NA
DR 128: Phase unbalanced voltage not
available
BOOL
FALSE
O
x
T_PH_U_V
DR 128: Delay time for phase unbalanced
voltage
REAL
0.0
O
x
T_PH_U_V_QC
Quality code of T_PH_U_V
BYTE
0
O
T_PH_U_V_OFF
DR 128: Delay time for phase unbalanced
voltage OFF
BOOL
FALSE
O
x
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
49
I/O (parameter)
Comment
Data type
Default
Type
OCM
T_PH_U_V_NA
DR 128: Delay time for phase unbalanced
voltage not available
BOOL
FALSE
O
x
UNDER_VOLT
DR 128: Under voltage
REAL
0.0
O
x
UNDER_VOLT_QC
Quality code of UNDER_VOLT
BYTE
0
O
UNDER_VOLT_OFF
DR 128: Under voltage OFF
BOOL
FALSE
O
x
UNDER_VOLT_NA
DR 128: Under voltage not available
BOOL
FALSE
O
x
OVER_VOLT
DR 128: Over voltage
REAL
0.0
O
x
OVER_VOLT_QC
Quality code of OVER_VOLT
BYTE
0
O
OVER_VOLT_OFF
DR 128: Over voltage OFF
BOOL
FALSE
O
x
OVER_VOLT_NA
DR 128: Over voltage not available
BOOL
FALSE
O
x
T_UN_VOLT
DR 128: Delay time for under voltage
REAL
0.0
O
x
T_UN_VOLT_QC
Quality code of T_UN_VOLT
BYTE
0
O
T_UN_VOLT_OFF
DR 128: Delay time for under voltage OFF
BOOL
FALSE
O
x
T_UN_VOLT_NA
DR 128: Delay time for under voltage not
available
BOOL
FALSE
O
x
T_OV_VOLT
DR 128: Delay time for over voltage
REAL
0.0
O
x
T_OV_VOLT_QC
Quality code of T_OV_VOLT
BYTE
0
O
T_OV_VOLT_OFF
DR 128: Delay time for over voltage OFF
BOOL
FALSE
O
x
T_OV_VOLT_NA
DR 128: Delay time for over voltage not
available
BOOL
FALSE
O
x
PH_UNBL_CUR
DR 128: Phase unbalanced current
REAL
0.0
O
x
PH_UNBL_CUR_QC
Quality code of PH_UNBL_CUR
BYTE
0
O
PH_UNBL_CUR_OFF
DR 128: Phase unbalanced current OFF
BOOL
FALSE
O
x
PH_UNBL_CUR_NA
DR 128: Phase unbalanced current not
available
BOOL
FALSE
O
x
T_PH_U_CUR
DR 128: Delay time for phase unbalanced
current
REAL
0.0
O
x
T_PH_U_CUR_QC
Quality code of T_PH_U_CUR
BYTE
0
O
T_PH_U_CUR_OFF
DR 128: Delay time for phase unbalanced
current OFF
BOOL
FALSE
O
x
T_PH_U_CUR_NA
DR 128: Delay time for phase unbalanced
current not available
BOOL
FALSE
O
x
EV1_OUT1
DR 128: 1. event for the 1st output
BYTE
0
O
x
EV1_OUT1_QC
Quality code of EV1_OUT1
BYTE
0
O
EV1_OUT1_OFF
DR 128: 1. event for the 1st output OFF
BOOL
FALSE
O
x
EV1_OUT1_NA
DR 128: 1. event for the 1st output not
available
BOOL
FALSE
O
x
EV2_OUT1
DR 128: 2. event for the 1st output
BYTE
0
O
x
EV2_OUT1_QC
Quality code of EV2_OUT1
BYTE
0
O
EV2_OUT1_OFF
DR 128: 2. event for the 1st output OFF
BOOL
FALSE
O
x
EV2_OUT1_NA
DR 128: 2. event for the 1st output not
available
BOOL
FALSE
O
x
EV3_OUT1
DR 128: 3. event for the 1st output
BYTE
0
O
x
EV3_OUT1_QC
Quality code of EV3_OUT1
BYTE
0
O
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
50
Function Manual, 11/2008, A5E02316914A-01
I/O (parameter)
Comment
Data type
Default
Type
OCM
EV3_OUT1_OFF
DR 128: 3. event for the 1st output OFF
BOOL
FALSE
O
x
EV3_OUT1_NA
DR 128: 3. event for the 1st output not
available
BOOL
FALSE
O
x
EV4_OUT1
DR 128: 4. event for the 1st output
BYTE
0
O
x
EV4_OUT1_QC
Quality code of EV4_OUT1
BYTE
0
O
EV4_OUT1_OFF
DR 128: 4. event for the 1st output OFF
BOOL
FALSE
O
x
EV4_OUT1_NA
DR 128: 4. event for the 1st output not
available
BOOL
FALSE
O
x
EV5_OUT1
DR 128: 5. event for the 1st output
BYTE
0
O
x
EV5_OUT1_QC
Quality code of EV5_OUT1
BYTE
0
O
EV5_OUT1_OFF
DR 128: 5. event for the 1st output OFF
BOOL
FALSE
O
x
EV5_OUT1_NA
DR 128: 5. event for the 1st output not
available
BOOL
FALSE
O
x
EV6_OUT1
DR 128: 6. event for the 1st output
BYTE
0
O
x
EV6_OUT1_QC
Quality code of EV6_OUT1
BYTE
0
O
EV6_OUT1_OFF
DR 128: 6. event for the 1st output OFF
BOOL
FALSE
O
x
EV6_OUT1_NA
DR 128: 6. event for the 1st output not
available
BOOL
FALSE
O
x
EV1_OUT2
DR 128: 1. event for the 2nd output
BYTE
0
O
x
EV1_OUT2_QC
Quality code of EV1_OUT2
BYTE
0
O
EV1_OUT2_OFF
DR 128: 1. event for the 2nd output OFF
BOOL
FALSE
O
x
EV1_OUT2_NA
DR 128: 1. event for the 2nd output not
available
BOOL
FALSE
O
x
EV2_OUT2
DR 128: 2. event for the 2nd output
BYTE
0
O
x
EV2_OUT2_QC
Quality code of EV2_OUT2
BYTE
0
O
EV2_OUT2_OFF
DR 128: 2. event for the 2nd output OFF
BOOL
FALSE
O
x
EV2_OUT2_NA
DR 128: 2. event for the 2nd output not
available
BOOL
FALSE
O
x
EV3_OUT2
DR 128: 3. event for the 2nd output
BYTE
0
O
x
EV3_OUT2_QC
Quality code of EV3_OUT2
BYTE
0
O
EV3_OUT2_OFF
DR 128: 3. event for the 2nd output OFF
BOOL
FALSE
O
x
EV3_OUT2_NA
DR 128: 3. event for the 2nd output not
available
BOOL
FALSE
O
x
EV4_OUT2
DR 128: 4. event for the 2nd output
BYTE
0
O
x
EV4_OUT2_QC
Quality code of EV4_OUT2
BYTE
0
O
EV4_OUT2_OFF
DR 128: 4. event for the 2nd output OFF
BOOL
FALSE
O
x
EV4_OUT2_NA
DR 128: 4. event for the 2nd output not
available
BOOL
FALSE
O
x
EV5_OUT2
DR 128: 5. event for the 2nd output
BYTE
0
O
x
EV5_OUT2_QC
Quality code of EV5_OUT2
BYTE
0
O
EV5_OUT2_OFF
DR 128: 5. event for the 2nd output OFF
BOOL
FALSE
O
x
EV5_OUT2_NA
DR 128: 5. event for the 2nd output not
available
BOOL
FALSE
O
x
EV6_OUT2
DR 128: 6. event for the 2nd output
BYTE
0
O
x
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
51
I/O (parameter)
Comment
Data type
Default
Type
OCM
EV6_OUT2_QC
Quality code of EV6_OUT2
BYTE
0
O
EV6_OUT2_OFF
DR 128: 6. event for the 2nd output OFF
BOOL
FALSE
O
x
EV6_OUT2_NA
DR 128: 6. event for the 2nd output not
available
BOOL
FALSE
O
x
EV1_OUT3
DR 128: 1. event for the 3rd output
BYTE
0
O
x
EV1_OUT3_QC
Quality code of EV1_OUT3
BYTE
0
O
EV1_OUT3_OFF
DR 128: 1. event for the 3rd output OFF
BOOL
FALSE
O
x
EV1_OUT3_NA
DR 128: 1. event for the 3rd output not
available
BOOL
FALSE
O
x
EV2_OUT3
DR 128: 2. event for the 3rd output
BYTE
0
O
x
EV2_OUT3_QC
Quality code of EV2_OUT3
BYTE
0
O
EV2_OUT3_OFF
DR 128: 2. event for the 3rd output OFF
BOOL
FALSE
O
x
EV2_OUT3_NA
DR 128: 2. event for the 3rd output not
available
BOOL
FALSE
O
x
EV3_OUT3
DR 128: 3. event for the 3rd output
BYTE
0
O
x
EV3_OUT3_QC
Quality code of EV3_OUT3
BYTE
0
O
EV3_OUT3_OFF
DR 128: 3. event for the 3rd output OFF
BOOL
FALSE
O
x
EV3_OUT3_NA
DR 128: 3. event for the 3rd output not
available
BOOL
FALSE
O
x
EV4_OUT3
DR 128: 4. event for the 3rd output
BYTE
0
O
x
EV4_OUT3_QC
Quality code of EV4_OUT3
BYTE
0
O
EV4_OUT3_OFF
DR 128: 4. event for the 3rd output OFF
BOOL
FALSE
O
x
EV4_OUT3_NA
DR 128: 4. event for the 3rd output not
available
BOOL
FALSE
O
x
EV5_OUT3
DR 128: 5. event for the 3rd output
BYTE
0
O
x
EV5_OUT3_QC
Quality code of EV5_OUT3
BYTE
0
O
EV5_OUT3_OFF
DR 128: 5. event for the 3rd output OFF
BOOL
FALSE
O
x
EV5_OUT3_NA
DR 128: 5. event for the 3rd output not
available
BOOL
FALSE
O
x
EV6_OUT3
DR 128: 6. event for the 3rd output
BYTE
0
O
x
EV6_OUT3_QC
Quality code of EV6_OUT3
BYTE
0
O
EV6_OUT3_OFF
DR 128: 6. event for the 3rd output OFF
BOOL
FALSE
O
x
EV6_OUT3_NA
DR 128: 6. event for the 3rd output not
available
BOOL
FALSE
O
x
EV_OUT4
DR 128: Event for the 4th output
BYTE
0
O
x
EV_OUT4_QC
Quality code of EV_OUT4
BYTE
0
O
EV_OUT4_OFF
DR 128: Event for the 4th output OFF
BOOL
FALSE
O
x
EV_OUT4_NA
DR 128: Event for the 4th output not
available
BOOL
FALSE
O
x
EV_OUT5
DR 128: Event for the 5th output
BYTE
0
O
x
EV_OUT5_QC
Quality code of EV_OUT5
BYTE
0
O
EV_OUT5_OFF
DR 128: Event for the 5th output OFF
BOOL
FALSE
O
x
EV_OUT5_NA
DR 128: Event for the 5th output not
available
BOOL
FALSE
O
x
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
52
Function Manual, 11/2008, A5E02316914A-01
I/O (parameter)
Comment
Data type
Default
Type
OCM
EV_OUT6
DR 128: Event for the 6th output
BYTE
0
O
x
EV_OUT6_QC
Quality code of EV_OUT6
BYTE
0
O
EV_OUT6_OFF
DR 128: Event for the 6th output OFF
BOOL
FALSE
O
x
EV_OUT6_NA
DR 128: Event for the 6th output not
available
BOOL
FALSE
O
x
OV_LD_A
DR 129: Overload parameter IR parameter
set A (PS A)
REAL
0.0
O
x
OV_LD_A_QC
Quality code of OV_LD_A
BYTE
0
O
OV_LD_A_OFF
DR 129: Overload parameter IR parameter
set A (PS A) OFF
BOOL
FALSE
O
x
OV_LD_A_NA
DR 129: Overload parameter IR parameter
set A (PS A) not available
BOOL
FALSE
O
x
OV_LD_N_A
DR 129: Overload N-phase IN PS A (WL)
REAL
0.0
O
x
OV_LD_N_A_QC
Quality code of OV_LD_N_A
BYTE
0
O
OV_LD_N_A_OFF
DR 129: Overload N-phase IN PS A (WL)
OFF
BOOL
FALSE
O
x
OV_LD_N_A_NA
DR 129: Overload N-phase IN PS A (WL)
not available
BOOL
FALSE
O
x
TL_CL_A
DR 129: Time lag class tR PS A
REAL
0.0
O
x
TL_CL_A_QC
Quality code of TL_CL_A
BYTE
0
O
TL_CL_A_OFF
DR 129: Time lag class tR PS A OFF
BOOL
FALSE
O
x
TL_CL_A_NA
DR 129: Time lag class tR PS A not
available
BOOL
FALSE
O
x
IN_PRO_PARA_A
DR 129: Instantaneous protection
parameter li PS A
REAL
0.0
O
x
IN_PRO_PARA_A_QC
Quality code of IN_PRO_PARA_A
BYTE
0
O
IN_PRO_PARA_A_OFF
DR 129: Instantaneous protection
parameter li PS A OFF
BOOL
FALSE
O
x
IN_PRO_PARA_A_NA
DR 129: Instantaneous protection
parameter li PS A not available
BOOL
FALSE
O
x
SHORT_D_PROT_A
DR 129: Short time delayed prot.
parameter lsd PS A
REAL
0.0
O
x
SHORT_D_PROT_A_QC
Quality code of SHORT_D_PROT_A
BYTE
0
O
SHORT_D_PROT_A_OFF
DR 129: Short time delayed prot.
parameter lsd PS A OFF
BOOL
FALSE
O
x
SHORT_D_PROT_A_NA
DR 129: Short time delayed prot.
parameter lsd PS A not available
BOOL
FALSE
O
x
T_STRIP_A
DR 129: Delay time for S-trip tsd PS A
REAL
0.0
O
x
T_STRIP_A_QC
Quality code of T_STRIP_A
BYTE
0
O
T_STRIP_A_OFF
DR 129: Delay time for S-trip tsd PS A
OFF
BOOL
FALSE
O
x
T_STRIP_A_NA
DR 129: Delay time for S-trip tsd PS A not
available
BOOL
FALSE
O
x
E_FLT_PROT_A
DR 129: Earth fault protection parameter
lg1 PS A
REAL
0.0
O
x
E_FLT_PROT_A_QC
Quality code of E_FLT_PROT_A
BYTE
0
O
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
53
I/O (parameter)
Comment
Data type
Default
Type
OCM
E_FLT_PROT_A_OFF
DR 129: Earth fault protection parameter
lg1 PS A OFF
BOOL
FALSE
O
x
E_FLT_PROT_A_NA
DR 129: Earth fault protection parameter
lg1 PS A not available
BOOL
FALSE
O
x
T_EFLT_A
DR 129: Delay time earth fault protection
tg1 PS A
REAL
0.0
O
x
T_EFLT_A_QC
Quality code of T_EFLT_A
BYTE
0
O
T_EFLT_A_OFF
DR 129: Delay time earth fault protection
tg1 PS A OFF
BOOL
FALSE
O
x
T_EFLT_A_NA
DR 129: Delay time earth fault protection
tg1 PS A not available
BOOL
FALSE
O
x
E_FLT_PROT2_A
DR 129: Earth fault protection parameter
lg2 PS A
REAL
0.0
O
x
E_FLT_PROT2_A_QC
Quality code of E_FLT_PROT2_A
BYTE
0
O
E_FLT_PROT2_A_OFF
DR 129: Earth fault protection parameter
lg2 PS A OFF
BOOL
FALSE
O
x
E_FLT_PROT2_A_NA
DR 129: Earth fault protection parameter
lg2 PS A not available
BOOL
FALSE
O
x
T_EFLT2_A
DR 129: Delay time earth fault protection
tg2 PS A
REAL
0.0
O
x
T_EFLT2_A_QC
Quality code of T_EFLT2_A
BYTE
0
O
T_EFLT2_A_OFF
DR 129: Delay time earth fault protection
tg2 PS A OFF
BOOL
FALSE
O
x
T_EFLT2_A_NA
DR 129: Delay time earth fault protection
tg2 PS A not available
BOOL
FALSE
O
x
I2T_D_STRIP_A
DR 129: I2t curve for delayed S-trip PS A
BOOL
FALSE
O
x
I2T_D_STRIP_A_QC
Quality code of I2T_D_STRIP_A
BYTE
0
O
I2T_D_STRIP_A_OFF
DR 129: I2t curve for delayed S-trip PS A
OFF
BOOL
FALSE
O
x
I2T_D_STRIP_A_NA
DR 129: I2t curve for delayed S-trip PS A
not available
BOOL
FALSE
O
x
I2T_EFLT_PROT_A
DR 129: I2t curve for earth fault protection
PS A
BOOL
FALSE
O
x
I2T_EFLT_PROT_A_QC
Quality code of I2T_EFLT_PROT_A
BYTE
0
O
I2T_EFLT_PROT_A_OFF
DR 129: I2t curve for earth fault protection
PS A OFF
BOOL
FALSE
O
x
I2T_EFLT_PROT_A_NA
DR 129: I2t curve for earth fault protection
PS A not available
BOOL
FALSE
O
x
I4T_OVLD_PROT_A
DR 129: I4t curve for overload protection
PS A
BOOL
FALSE
O
x
I4T_OVLD_PROT_A_QC
Quality code of I4T_OVLD_PROT_A
BYTE
0
O
I4T_OVLD_PROT_A_OFF
DR 129: I4t curve for overload protection
PS A OFF
BOOL
FALSE
O
x
I4T_OVLD_PROT_A_NA
DR 129: I4t curve for overload protection
PS A not available
BOOL
FALSE
O
x
THERM_MEM_A
DR 129: Thermal memory PS A
BOOL
FALSE
O
x
THERM_MEM_A_QC
Quality code of THERM_MEM_A
BYTE
0
O
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
54
Function Manual, 11/2008, A5E02316914A-01
I/O (parameter)
Comment
Data type
Default
Type
OCM
THERM_MEM_A_OFF
DR 129: Thermal memory PS A OFF
BOOL
FALSE
O
x
THERM_MEM_A_NA
DR 129: Thermal memory PS A not
available
BOOL
FALSE
O
x
PH_L_SEN_A
DR 129: Phase loss sensitivity PS A
BOOL
FALSE
O
x
PH_L_SEN_A_QC
Quality code of PH_L_SEN_A
BYTE
0
O
PH_L_SEN_A_OFF
DR 129: Phase loss sensitivity PS A OFF
BOOL
FALSE
O
x
PH_L_SEN_A_NA
DR 129: Phase loss sensitivity PS A not
available
BOOL
FALSE
O
x
THERM_T_A
DR 129: Thermal time constant PS A
REAL
0.0
O
x
THERM_T_A_QC
Quality code of THERM_T_A
BYTE
0
O
THERM_T_A_OFF
DR 129: Thermal time constant PS A OFF
BOOL
FALSE
O
x
THERM_T_A_NA
DR 129: Thermal time constant PS A not
available
BOOL
FALSE
O
x
OV_LD_B
DR 129: Overload parameter IR parameter
(PS B)
REAL
0.0
O
x
OV_LD_B_QC
Quality code of OV_LD_B
BYTE
0
O
OV_LD_B_OFF
DR 129: Overload parameter IR parameter
(PS B) OFF
BOOL
FALSE
O
x
OV_LD_B_NA
DR 129: Overload parameter IR parameter
(PS B) not available
BOOL
FALSE
O
x
OV_LD_N_B
DR 129: Overload N-phase IN PS B (WL)
REAL
0.0
O
x
OV_LD_N_B_QC
Quality code of OV_LD_N_B
BYTE
0
O
OV_LD_N_B_OFF
DR 129: Overload N-phase IN PS B (WL)
OFF
BOOL
FALSE
O
x
OV_LD_N_B_NA
DR 129: Overload N-phase IN PS B (WL)
not available
BOOL
FALSE
O
x
TL_CL_B
DR 129: Time lag class tR PS B
REAL
0.0
O
x
TL_CL_B_QC
Quality code of TL_CL_B
BYTE
0
O
TL_CL_B_OFF
DR 129: Time lag class tR PS B OFF
BOOL
FALSE
O
x
TL_CL_B_NA
DR 129: Time lag class tR PS B not
available
BOOL
FALSE
O
x
IN_PRO_PARA_B
DR 129: Instantaneous protection
parameter li PS B
REAL
0.0
O
x
IN_PRO_PARA_B_QC
Quality code of IN_PRO_PARA_B
BYTE
0
O
IN_PRO_PARA_B_OFF
DR 129: Instantaneous protection
parameter li PS B
BOOL
FALSE
O
x
IN_PRO_PARA_B_NA
DR 129: Instantaneous protection
parameter li PS B not available
BOOL
FALSE
O
x
SHORT_D_PROT_B
DR 129: Short time delayed prot.
parameter lsd PS B
REAL
0.0
O
x
SHORT_D_PROT_B_QC
Quality code of SHORT_D_PROT_B
BYTE
0
O
SHORT_D_PROT_B_OFF
DR 129: Short time delayed prot.
parameter lsd PS B OFF
BOOL
FALSE
O
x
SHORT_D_PROT_B_NA
DR 129: Short time delayed prot.
parameter lsd PS B not available
BOOL
FALSE
O
x
T_STRIP_B
DR 129: Delay time for S-trip tsd PS B
REAL
0.0
O
x
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
55
I/O (parameter)
Comment
Data type
Default
Type
OCM
T_STRIP_B_QC
Quality code of T_STRIP_B
BYTE
0
O
T_STRIP_B_OFF
DR 129: Delay time for S-trip tsd PS B
OFF
BOOL
FALSE
O
x
T_STRIP_B_NA
DR 129: Delay time for S-trip tsd PS B not
available
BOOL
FALSE
O
x
E_FLT_PROT_B
DR 129: Earth fault protection parameter
lg1 PS B
REAL
0.0
O
x
E_FLT_PROT_B_QC
Quality code of E_FLT_PROT_B
BYTE
0
O
E_FLT_PROT_B_OFF
DR 129: Earth fault protection parameter
lg1 PS B OFF
BOOL
FALSE
O
x
E_FLT_PROT_B_NA
DR 129: Earth fault protection parameter
lg1 PS B not available
BOOL
FALSE
O
x
T_EFLT_B
DR 129: Delay time earth fault protection
tg1 PS B
REAL
0.0
O
x
T_EFLT_B_QC
Quality code of T_EFLT_B
BYTE
0
O
T_EFLT_B_OFF
DR 129: Delay time earth fault protection
tg1 PS B OFF
BOOL
FALSE
O
x
T_EFLT_B_NA
DR 129: Delay time earth fault protection
tg1 PS B not available
BOOL
FALSE
O
x
E_FLT_PROT2_B
DR 129: Earth fault protection parameter
lg2 PS B
REAL
0.0
O
x
E_FLT_PROT2_B_QC
Quality code of E_FLT_PROT2_B
BYTE
0
O
E_FLT_PROT2_B_OFF
DR 129: Earth fault protection parameter
lg2 PS B OFF
BOOL
FALSE
O
x
E_FLT_PROT2_B_NA
DR 129: Earth fault protection parameter
lg2 PS B not available
BOOL
FALSE
O
x
T_EFLT2_B
DR 129: Delay time earth fault protection
tg2 PS B
REAL
0.0
O
x
T_EFLT2_B_QC
Quality code of T_EFLT2_B
BYTE
0
O
T_EFLT2_B_OFF
DR 129: Delay time earth fault protection
tg2 PS B OFF
BOOL
FALSE
O
x
T_EFLT2_B_NA
DR 129: Delay time earth fault protection
tg2 PS B not available
BOOL
FALSE
O
x
I2T_D_STRIP_B
DR 129: I2t curve for delayed S-trip PS B
BOOL
FALSE
O
x
I2T_D_STRIP_B_QC
Quality code of I2T_D_STRIP_B
BYTE
0
O
I2T_D_STRIP_B_OFF
DR 129: I2t curve for delayed S-trip PS B
OFF
BOOL
FALSE
O
x
I2T_D_STRIP_B_NA
DR 129: I2t curve for delayed S-trip PS B
not available
BOOL
FALSE
O
x
I2T_EFLT_PROT_B
DR 129: I2t curve for earth fault protection
PS B
BOOL
FALSE
O
x
I2T_EFLT_PROT_B_QC
Quality code of I2T_EFLT_PROT_B
BYTE
0
O
I2T_EFLT_PROT_B_OFF
DR 129: I2t curve for earth fault protection
PS B OFF
BOOL
FALSE
O
x
I2T_EFLT_PROT_B_NA
DR 129: I2t curve for earth fault protection
PS B not available
BOOL
FALSE
O
x
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
56
Function Manual, 11/2008, A5E02316914A-01
I/O (parameter)
Comment
Data type
Default
Type
OCM
I4T_OVLD_PROT_B
DR 129: I4t curve for overload protection
PS B
BOOL
FALSE
O
x
I4T_OVLD_PROT_B_QC
Quality code of I4T_OVLD_PROT_B
BYTE
0
O
I4T_OVLD_PROT_B_OFF
DR 129: I4t curve for overload protection
PS B OFF
BOOL
FALSE
O
x
I4T_OVLD_PROT_B_NA
DR 129: I4t curve for overload protection
PS B not available
BOOL
FALSE
O
x
THERM_MEM_B
DR 129: Thermal memory PS B
BOOL
FALSE
O
x
THERM_MEM_B_QC
Quality code of THERM_MEM_B
BYTE
0
O
THERM_MEM_B_OFF
DR 129: Thermal memory PS B OFF
BOOL
FALSE
O
x
THERM_MEM_B_NA
DR 129: Thermal memory PS B not
available
BOOL
FALSE
O
x
PH_L_SEN_B
DR 129: Phase loss sensitivity PS B
BOOL
FALSE
O
x
PH_L_SEN_B_QC
Quality code of PH_L_SEN_B
BYTE
0
O
PH_L_SEN_B_OFF
DR 129: Phase loss sensitivity PS B OFF
BOOL
FALSE
O
x
PH_L_SEN_B_NA
DR 129: Phase loss sensitivity PS B not
available
BOOL
FALSE
O
x
THERM_T_B
DR 129: Thermal time constant PS B
REAL
0.0
O
x
THERM_T_B_QC
Quality code of THERM_T_B
BYTE
0
O
THERM_T_B_OFF
DR 129: Thermal time constant PS B OFF
BOOL
FALSE
O
x
THERM_T_B_NA
DR 129: Thermal time constant PS B not
available
BOOL
FALSE
O
x
LD_SHED
DR 129: Load shedding
REAL
0.0
O
x
LD_SHED_QC
Quality code of LD_SHED
BYTE
0
O
LD_SHED_OFF
DR 129: Load shedding OFF
BOOL
FALSE
O
x
LD_SHED_NA
DR 129: Load shedding not available
BOOL
FALSE
O
x
LD_REST
DR 129: Load restorage
REAL
0.0
O
x
LD_REST_QC
Quality code of LD_REST
BYTE
0
O
LD_REST_OFF
DR 129: Load restorage OFF
BOOL
FALSE
O
x
LD_REST_NA
DR 129: Load restorage not available
BOOL
FALSE
O
x
T_SHED_REST
DR 129: Delay time load shedd./restorage
REAL
0.0
O
x
T_SHED_REST_QC
Quality code of T_SHED_REST
BYTE
0
O
T_SHED_REST_OFF
DR 129: Delay time load shedd./restorage
OFF
BOOL
FALSE
O
x
T_SHED_REST_NA
DR 129: Delay time load shedd./restorage
not available
BOOL
FALSE
O
x
ACT_PARA
DR 129: Active parameter set
BOOL
FALSE
O
x
ACT_PARA_QC
Quality code of ACT_PARA
BYTE
0
O
ACT_PARA_OFF
DR 129: Active parameter set OFF
BOOL
FALSE
O
x
ACT_PARA_NA
DR 129: Active parameter set not available
BOOL
FALSE
O
x
EARTH_FLT_CUR
DR 129: Determination of earth fault
current
REAL
0.0
O
x
EARTH_FLT_CUR_QC
Quality code of EARTH_FLT_CUR
BYTE
0
O
EARTH_FLT_CUR_OFF
DR 129: Determination of earth fault
current OFF
BOOL
FALSE
O
x
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
57
I/O (parameter)
Comment
Data type
Default
Type
OCM
EARTH_FLT_CUR_NA
DR 129: Determination of earth fault
current not available
BOOL
FALSE
O
x
R_CUR_GRD_FLT
DR 129: Rated current ground fault
transformer
REAL
0.0
O
x
R_CUR_GRD_FLT_QC
Quality code of R_CUR_GRD_FL
BYTE
0
O
R_CUR_GRD_FLT_OFF
DR 129: Rated current ground fault
transformer OFF
BOOL
FALSE
O
x
R_CUR_GRD_FLT_NA
DR 129: Rated current ground fault
transformer not available
BOOL
FALSE
O
x
MLFB
DR 129: Catalog number CB as upgraded
or changed by cust. or service (text)
STRING[18]
O
x
MLFB_QC
Quality code of MLFB
BYTE
0
O
MLFB_OFF
DR 129: Catalog number CB as upgraded
or changed by cust. or service (text) OFF
BOOL
FALSE
O
x
MLFB_NA
DR 129: Catalog number CB as upgraded
or changed by cust. or service (text) not
available
BOOL
FALSE
O
x
RP_NORM_O
DR 130: Real power in normal direction
REAL
0.0
O
RP_NORM_O_QC
Quality code of RP_NORM_O
BYTE
0
O
RP_REV_O
DR 130: Real power in reverse direction
REAL
0.0
O
RP_REV_O_QC
Quality code of RP_REV_O
BYTE
0
O
PF_CAP_O
DR 130: Power factor capacitive
REAL
0.0
O
PF_CAP_O_QC
Quality code of PF_CAP_O
BYTE
0
O
PF_IND_O
DR 130: Power factor inductive
REAL
0.0
O
PF_IND_O_QC
Quality code of PF_IND_O
BYTE
0
O
T_RP_NORM_O
DR 130: Delay time for real power in
normal direction
REAL
0.0
O
T_RP_NORM_O_QC
Quality code of T_RP_NORM_O
BYTE
0
O
T_RP_REV_O
DR 130: Delay time for real power in
reverse direction
REAL
0.0
O
T_RP_REV_O_QC
Quality code of T_RP_REV_O
BYTE
0
O
T_PF_CAP_O
DR 130: Delay time for power factor
capacitive
REAL
0.0
O
T_PF_CAP_O_QC
Quality code of T_PF_CAP_O
BYTE
0
O
T_PF_IND_O
DR 130: Delay time for power factor
inductive
REAL
0.0
O
T_PF_IND_O_QC
Quality code of T_PF_IND_O
BYTE
0
O
OVER_FRQ_O
DR 130: Over frequency
REAL
0.0
O
OVER_FRQ_O_QC
Quality code of OVER_FRQ_O
BYTE
0
O
T_OVER_FRQ_O
DR 130: Delay time for over frequency
REAL
0.0
O
T_OVER_FRQ_O_QC
Quality code of T_OVER_FRQ_O
BYTE
0
O
UNDER_FRQ_O
DR 130: Under frequency
REAL
0.0
O
UNDER_FRQ_O_QC
Quality code of UNDER_FRQ_O
BYTE
0
O
T_UNDER_FRQ_O
DR 130: Delay time for under frequency
REAL
0.0
O
T_UNDER_FRQ_O_QC
Quality code of T_UNDER_FRQ_O
BYTE
0
O
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
58
Function Manual, 11/2008, A5E02316914A-01
I/O (parameter)
Comment
Data type
Default
Type
OCM
CUR_THD_O
DR 130: THD current
REAL
0.0
O
CUR_THD_O_QC
Quality code of CUR_THD_O
BYTE
0
O
T_CUR_THD_O
DR 130: Delay time for THD current
REAL
0.0
O
T_CUR_THD_O_QC
Quality code of T_CUR_THD_O
BYTE
0
O
VOLT_THD_O
DR 130: THD voltage
REAL
0.0
O
VOLT_THD_O_QC
Quality code of VOLT_THD_O
BYTE
0
O
T_VOLT_THD_O
DR 130: Delay time for THD voltage
REAL
0.0
O
T_VOLT_THD_O_QC
Quality code of T_VOLT_THD_O
BYTE
0
O
CREST_F_O
DR 130: Crest factor
REAL
0.0
O
CREST_F_O_QC
Quality code of CREST_F_O
BYTE
0
O
FORM_F_O
DR 130: Form factor
REAL
0.0
O
FORM_F_O_QC
Quality code of FORM_F_O
BYTE
0
O
T_CREST_F_O
DR 130: Delay time for crest factor
REAL
0.0
O
T_CREST_F_O_QC
Quality code of T_CREST_F_O
BYTE
0
O
T_FORM_F_O
DR 130: Delay time for form factor
REAL
0.0
O
T_FORM_F_O_QC
Quality code of T_FORM_F_O
BYTE
0
O
RP_DEM_O
DR 130: Demand real power
REAL
0.0
O
RP_DEM_O_QC
Quality code of PR_DEM_O
BYTE
0
O
AP_DEM_O
DR 130: Demand apparent power
REAL
0.0
O
AP_DEM_O_QC
Quality code of AP_DEM_O
BYTE
0
O
T_RP_DEM_O
DR 130: Delay time demand of the real
power
REAL
0.0
O
T_RP_DEM_O_QC
Quality code of T_RP_DEM_O
BYTE
0
O
T_AP_DEM_O
DR 130: Delay time demand of the
apparent power
REAL
0.0
O
T_AP_DEM_O_QC
Quality code of T_AP_DEM_O
BYTE
0
O
RAP_DEM_O
DR 130: Demand reactive power
REAL
0.0
O
RAP_DEM_O_QC
Quality code of RAP_DEM_O
BYTE
0
O
RAP_NORM_O
DR 130: Reactive power in normal
direction
REAL
0.0
O
RAP_NORM_O_QC
Quality code of RAP_NORM_O
BYTE
0
O
T_RAP_DEM_O
DR 130: Delay time demand of the
reactive power
REAL
0.0
O
T_RAP_DEM_O_QC
Quality code of T_RAP_DEM_O
BYTE
0
O
T_RAP_NORM_O
DR 130: Delay time for reactive power in
normal direction
REAL
0.0
O
T_RAP_NORM_O_QC
Quality code of T_RAP_NORM_O
BYTE
0
O
RAP_REV_O
DR 130: Reactive power in reverse
direction
REAL
0.0
O
RAP_REV_O_QC
Quality code of RAP_REV_O
BYTE
0
O
AP_O
DR 130: Apparent power
REAL
0.0
O
AP_O_QC
Quality code of AP_O
BYTE
0
O
T_RAP_REV_O
DR 130: Delay time for reactive power in
reverse direction
REAL
0.0
O
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
59
I/O (parameter)
Comment
Data type
Default
Type
OCM
T_RAP_REV_O_QC
Quality code of T_RAP_REV_O
BYTE
0
O
T_AP_O
DR 130: Delay time for apparent power
REAL
0.0
O
T_AP_O_QC
Quality code of T_AP_O
BYTE
0
O
CUR_OVER_O
DR 130: Over current
REAL
0.0
O
CUR_OVER_O_QC
Quality code of CUR_OVER_O
BYTE
0
O
CUR_GRD_O
DR 130: Earth fault current
REAL
0.0
O
CUR_GRD_O_QC
Quality code of CUR_GRD_O
BYTE
0
O
CUR_N_O
DR 130: Over current N-phase
REAL
0.0
O
CUR_N_O_QC
Quality code of CUR_N_O
BYTE
0
O
CUR_DEM_O
DR 130: Demand of the current
REAL
0.0
O
CUR_DEM_O_QC
Quality code of CUR_DEM_O
BYTE
0
O
T_CUR_OVER_O
DR 130: Delay time for over current
REAL
0.0
O
T_CUR_OVER_O_QC
Quality code of T_CUR_OVER_O
BYTE
0
O
T_CUR_GRD_O
DR 130: Delay time for over current
ground
REAL
0.0
O
T_CUR_GRD_O_QC
Quality code of T_CUR_GRD_O
BYTE
0
O
T_CUR_N_O
DR 130: Delay time for over current N-
phase
REAL
0.0
O
T_CUR_N_O_QC
Quality code of T_CUR_N_O
BYTE
0
O
UNBAL_CUR_O
DR 130: Phase unbalance current
REAL
0.0
O
UNBAL_CUR_O_QC
Quality code of UNBAL_CUR_O
BYTE
0
O
T_UNBAL_CUR_O
DR 130: Delay time for phase unbalance
current
REAL
0.0
O
T_UNBAL_CUR_O_QC
Quality code of T_UNBAL_CUR_O
BYTE
0
O
T_CUR_DEM_O
DR 130: Delay time for demand of the
current
REAL
0.0
O
T_CUR_DEM_O_QC
Quality code of T_CUR_DEM_O
BYTE
0
O
UNDER_VOLT_O
DR 130: Under voltage
REAL
0.0
O
UNDER_VOLT_O_QC
Quality code of UNDER_VOLT_O
BYTE
0
O
T_UNDER_VOLT_O
DR 130: Delay time for under voltage
REAL
0.0
O
T_UNDER_VOLT_O_QC
Quality code of T_UNDER_VOLT_O
BYTE
0
O
UNBAL_VOLT_O
DR 130: Phase unbalance voltage
REAL
0.0
O
UNBAL_VOLT_O_QC
Quality code of UNBAL_VOLT_O
BYTE
0
O
T_UNBAL_VOLT_O
DR 130: Delay time for phase unbalance
voltage
REAL
0.0
O
T_UNBAL_VOLT_O_QC
Quality code of T_UNBAL_VOLT_O
BYTE
0
O
OVER_VOLT_O
DR 130: Over voltage
REAL
0.0
O
OVER_VOLT_O_QC
Quality code of OVER_VOLT_O
BYTE
0
O
T_OVER_VOLT_O
DR 130: Delay time for over voltage
REAL
0.0
O
T_OVER_VOLT_O_QC
Quality code of T_OVER_VOLT_O
BYTE
0
O
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
60
Function Manual, 11/2008, A5E02316914A-01
3.2.10
Description of symbols and faceplates
Description of symbols and faceplates:
● Symbol with 1 measurement
● Faceplate
● Standard view
● Measurements view, current tab
● Measurements view, voltage tab
● Measurements view, active power/energy tab
● Measurements view, reactive power/energy tab
● Measurements view, apparent power tab
● Measurements view, miscellaneous tab
● Diagnosis view, warnings tab
● Diagnosis view, trip reason tab
● Diagnosis view, setpoints tab
● Maintenance view, maintenance 1 tab
● Maintenance view, maintenance 2 tab
● Maintenance view, operation tab
● Protect. para view, parameter set A
● Protect. para view, parameter set B
● Protect. para view, additional tab
● Ext. protect. para view, current tab
● Ext. protect. para view, voltage tab
● Ext. protect. para view, reactive power tab
● Ext. protect. para view, frequency tab
● Setpoints view, current tab
● Setpoints view, voltage tab
● Setpoints view, frequency tab
● Setpoints view, active power tab
● Setpoints view, apparent/reactive power tab
● Message suppression view
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
61
Block icon with 1 measurement
(1)
MAX_CUR
Figure 3-1
Symbol with 1 measurement
Meaning of measurements
Element (parameters)
Meaning
MAX_CUR
Maximum phase current
Faceplate
The faceplate available is described in this chapter.
The following views are available:
Standard
Measurements with the tabs
Current
MEASUREMENT_CUR
Voltage
MEASUREMENT_VOLT
Active power/energy MEASUREMENT_ACT_POW
Reactive
power/energy
MEASUREMENT_REACT_POW
Apparent power
MEASUREMENT_APP_POW
Miscellaneous
MEASUREMENT_MISC
Diagnosis with the tabs
Warnings
DIAG_WARN
Trip reason
DIAG_TRIP
Setpoints
DIAG_SETPOINTS
Maintenance with the tabs
Maintenance 1
MAINTENANCE_1
Maintenance 2
MAINTENANCE_2
Operation
MAINTENANCE_OP
Protect. para with the tabs
Parameter Set A
PARA_SET_A
Parameter Set B
PARA_SET_B
Additional
PROTPARA_ADD
Ext. Prot. Para with the tabs
Current
EXTPROTPARA_CUR
Voltage
EXTPROTPARA_VOLT
Active power
EXTPROTPARA_ACT_POW
Frequency
EXTPROTPARA_FREQ
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
62
Function Manual, 11/2008, A5E02316914A-01
Setpoints with the tabs
Current
SETPOINTS_CUR
Voltage
SETPOINTS_VOLT
Active power
SETPOINTS_ACT_POW
Apparent/Reactive
power
SETPOINTS_APP_REACT_PO
W
Frequency
SETPOINTS_FREQ
Msg. suppr.
Messages
Trend
The file name is composed as follows: @PG_DRV_3WL_"View".pdl
The PCS 7 standard displays @PCS7_alarm.pdl and @PCS7_trend.pdl are used for the
alarm and trend views.
The structure of the individual views of faceplates is described below.
The appearance of the faceplates differ depending on whether the 3WL is connected directly
to the DP master system or whether it is connected following a Y-link.
When the 3WL is connected following a Y-link, no data records can be read because the
device following a Y-link switches to DPV0 mode. This explains why faceplate views which
only contain values from data records are hidden. Values which are displayed despite this
and come from data records are cross-faced with "---". These measured values are therefore
not indicated in the faceplates.
The faceplates in the figures below are shown for direct connection of 3WL to the DP master
system.
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
63
Standard
(1)
QMAN_AUT / AUT_ON_OP
(2)
MAN_OFF
(3)
MAN_ON
(4)
RESET
(5)
CUR_L1
(6)
CUR_L2
(7)
CUR_L3
(8)
RES_MONERR
(9)
QMON_ERR
(10)
MAINT
(11)
POS_CB
(12)
QLOC_OFF / ST_CB
(13)
CUR_MAX
(14)
ST_CB
Figure 3-2
Faceplate for standard view
not ready
OFF
ON
tripped
Symbol for status
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
64
Function Manual, 11/2008, A5E02316914A-01
Element (parameters)
Meaning
Display when 3WL is
connected following Y-link
ST_CB
Status of circuit breaker (Not ready
/ OFF / ON / Tripped)
Yes
QLOC_OFF
Local turn off of circuit breaker / tripped
Yes
CUR_MAX
Current of phase with maximum load
Yes
POS_CB
Position of circuit breaker
Yes
MAINT
Maintenance mode active / inactive
Yes
QMON_ERR
Monitoring error active / inactive
Yes
QMAN_AUT / AUT_ON_OP
Manual / automatic changeover
Yes
MAN_OFF
Switch off circuit breaker operating command
Yes
MAN_ON
Switch on circuit breaker operating command
Yes
RESET
Reset "Tripped" or "Local turn off" status
Yes
CUR_L1
Current in phase L1
Yes
CUR_L2
Current in phase L2
Yes
CUR_L3
Current in phase L3
Yes
RES_MONERR
Reset monitoring error
Yes
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
65
Measurements – current tab (MEASUREMENT_CUR)
(1)
CUR_L2
(2)
CUR_N
(3)
CUR_DEM_L2
(4)
CUR_DEM3
(5)
CUR_UNBAL
(6)
CUR_DEM3PH
(7)
CUR_EARTH_F
(8)
THD_CUR94
(9)
CUR_DEM_L3
(10)
CUR_DEM_L1
(11)
CUR_L3
(12)
CUR_L1
Figure 3-3
Faceplate for measurements view, current tab
Element (parameters)
Meaning
Display when 3WL is
connected following Y-link
CUR_L1
Current in phase L1
Yes
CUR_L2
Current in phase L2
Yes
CUR_L3
Current in phase L3
Yes
CUR_N
Current in neutral conductor
Yes
CUR_DEM_L1
Demand for current L1
No
CUR_DEM_L2
Demand for current L2
No
CUR_DEM_L3
Demand for current L3
No
CUR_DEM3
Demand for 3-phase current
No
CUR_UNBAL
Phase unbalance current (as %)
No
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
66
Function Manual, 11/2008, A5E02316914A-01
Element (parameters)
Meaning
Display when 3WL is
connected following Y-link
CUR_DEM3PH
Mean current value over the three phases
No
CUR_EARTH_F
Current which flows to earth
No
THD_CUR94
THD of current
No
Measurements – voltage tab (MEASUREMENT_VOLT)
(1)
U_L1_N
(2)
U_L2_N
(3)
U_L3_N
(4)
VOLT_DEM_D
(5)
VOLT_DEM_S
(6)
VOLT_UNBAL
(7)
THD_VOLT
(8)
U_L3_L1
(9)
U_L2_L3
(10)
U_L1_L2
Figure 3-4
Faceplate for measurements view, voltage tab
Element (parameters)
Meaning
Display when 3WL is
connected following Y-link
U_L1_L2
Voltage Va-b
Yes
U_L2_L3
Voltage Vb-c
Yes
U_L3_L1
Voltage Vc-a
Yes
U_L1_N
Voltage Va-n
Yes
U_L2_N
Voltage Vb-n
Yes
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
67
Element (parameters)
Meaning
Display when 3WL is
connected following Y-link
U_L3_N
Voltage Vc-n
Yes
VOLT_DEM_D
Mean value of phase-to-phase voltage
No
VOLT_DEM_S
Mean value of neutral-point star voltage
No
VOLT_UNBAL
Phase unbalance voltage (as %)
No
THD_VOLT
THD of voltage
No
Measurements – active power/energy tab (MEASUREMENT_ACT_POW)
(1)
DEM_RP_L1
(2)
DEM_RP_L2
(3)
DEM_RP_L3
(4)
DEM_RP3
(5)
SUM_RP
(6)
ACT_W
(7)
RE_REV
(8)
RP_L3
(9)
RP_L2
(10)
RP_L1
Figure 3-5
Faceplate for measurements view, active power/energy tab
Element (parameters)
Meaning
Display when 3WL is connected
following Y-link
RP_L1
Active power in phase L1
No
RP_L2
Active power in phase L2
No
RP_L3
Active power in phase L3
No
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
68
Function Manual, 11/2008, A5E02316914A-01
Element (parameters)
Meaning
Display when 3WL is connected
following Y-link
DEM_RP_L1
Demand of active power in phase L1
No
DEM_RP_L2
Demand of active power in phase L2
No
DEM_RP_L3
Demand of active power in phase L3
No
DEM_RP3
Demand of 3-phase active power
No
SUM_RP
Total active power
No
ACT_W
Active energy in normal direction
Yes
RE_REV
Active energy in reverse direction
No
Measurements – reactive power/energy tab (MEASUREMENT_REACT_POW)
(1)
RAP_L1
(2)
RAP_L2
(3)
RAP_L3
(4)
SUM_RAP
(5)
DEM_RAP3
(6)
REC_E_NORM
(7)
REC_E_REV
Figure 3-6
Faceplate for measurements view, reactive power/energy tab
Element (parameters)
Meaning
Display when 3WL is
connected following Y-link
RAP_L1
Reactive power in phase L1
No
RAP_L2
Reactive power in phase L2
No
RAP_L3
Reactive power in phase L3
No
SUM_RAP
Total reactive power
No
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
69
Element (parameters)
Meaning
Display when 3WL is
connected following Y-link
DEM_RAP3
Demand of 3-phase active power
No
REC_E_NORM
Reactive energy in normal direction
No
REC_E_REV
Reactive energy in reverse direction
No
Measurements – apparent power tab (MEASUREMENT_APP_POW)
(1)
AP_L1
(2)
AP_L2
(3)
AP_L3
(4)
DEM_AP_L1
(5)
DEM_AP_L2
(6)
DEM_AP_L3
(7)
DEM_AP3
(8)
KVA_TOT
Figure 3-7
Faceplate for measurements view, apparent power tab
Element (parameters)
Meaning
Display when 3WL is
connected following Y-link
AP_L1
Apparent power in phase L1
No
AP_L2
Apparent power in phase L2
No
AP_L3
Apparent power in phase L3
No
DEM_AP_L1
Demand of apparent power in phase L1
No
DEM_AP_L2
Demand of apparent power in phase L2
No
DEM_AP_L3
Demand of apparent power in phase L3
No
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
70
Function Manual, 11/2008, A5E02316914A-01
Element (parameters)
Meaning
Display when 3WL is
connected following Y-link
DEM_AP3
Demand of 3-phase apparent power
No
KVA_TOT
Total apparent power
Yes
Measurements – miscellaneous tab (MEASUREMENT_MISC)
(1)
TMP_CUB
(2)
TMP_MSAE
(3)
PF_AVG
(4)
FRQ
(5)
FORM_F
(6)
CREST_F
(7)
PF_L3
(8)
PF_L2
(9)
PF_L1
Figure 3-8
Faceplate for measurements view, miscellaneous tab
Element (parameters)
Meaning
Display when 3WL is connected
following Y-link
PF_L1
Power factor in phase L1
No
PF_L2
Power factor in phase L2
No
PF_L3
Power factor in phase L3
No
TMP_CUB
Temperature in the control cabinet (acc. to in COM15)
No
TMP_MSAE
Temperature in circuit-breaker (acc. to in BSS)
No
PF_AVG
Mean power factor value
Yes
FRQ
Frequency
No
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
71
Element (parameters)
Meaning
Display when 3WL is connected
following Y-link
FORM_F
Form factor
No
CREST_F
Crest factor
No
Diagnosis – warnings tab (DIAG_WARN)
(1)
WRN_NO1
(2)
WRN_NO2
(3)
WRN_NO3
(4)
WRN_NO4
(5)
WRN_NO5
(6)
WRN_NO6
(7)
WRN_NO7
(8)
WRN_NO8
Figure 3-9
Faceplate for diagnosis view, warnings tab
Element (parameters)
Meaning
Display when 3WL is connected
following Y-link
WRN_NO1
1st warning currently active
No
WRN_NO2
2nd warning currently active
No
WRN_NO3
3rd warning currently active
No
WRN_NO4
4th warning currently active
No
WRN_NO5
5th warning currently active
No
WRN_NO6
6th warning currently active
No
WRN_NO7
7th warning currently active
No
WRN_NO8
8th warning currently active
No
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
72
Function Manual, 11/2008, A5E02316914A-01
Possible warnings
Pretrip for L
Overload
Overload N-phase
Load shedding warning
Load restorage
Phase unbalance current
µP-Error
Earth fault warning
Over temperature
Diagnosis – trip reason tab (DIAG_TRIP)
(1)
LST_TRIP
(2)
TRIP_NO
Figure 3-10
Faceplate for diagnosis view, trip reason tab
Element (parameters)
Meaning
Display when 3WL is connected
following Y-link
LST_TRIP
Trip reason
No
TRIP_NO
Accurate trip reason
in event of trip by extended protective function
No
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
73
Possible trip reasons (LST_TRIP)
Overload tripping (L)
Instantaneous short-circuit (I)
Short-time-delay short-circuit (S)
Ground fault (G)
Trip as a result of extended protection function
Overload in neutral conductor
Accurate trip reason in event of trip by extended protective function
Phase unbalance current
Phase unbalance voltage
Real power in normal direction
Real power in reverse direction
Over voltage
Under voltage
Over frequency
Under frequency
THD current
THD voltage
Change of phase rotation
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
74
Function Manual, 11/2008, A5E02316914A-01
Diagnosis – setpoints tab (DIAG_SETPOINTS)
(1)
SP_NO1
(2)
SP_NO2
(3)
SP_NO3
(4)
SP_NO4
(5)
SP_NO5
(6)
SP_NO6
(7)
SP_NO7
(8)
SP_NO8
Figure 3-11
Faceplate for diagnosis view, setpoints tab
Element (parameters)
Meaning
Display when 3WL is
connected following Y-link
SP_NO1
1st current case of setpoint being exceeded
No
SP_NO2
2nd current case of setpoint being exceeded
No
SP_NO3
3rd current case of setpoint being exceeded
No
SP_NO4
4th current case of setpoint being exceeded
No
SP_NO5
5th current case of setpoint being exceeded
No
SP_NO6
6th current case of setpoint being exceeded
No
SP_NO7
7th current case of setpoint being exceeded
No
SP_NO8
8th current case of setpoint being exceeded
No
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
75
Possible messages
Power factor capacitive
Power factor inductive
THD current
THD voltage
Crest factor
Form factor
Real power in normal direction
Real power in reverse direction
Demand real power
Demand apparent power
Demand reactive power
Reactive power in normal direction
Reactive power in reverse direction
Apparent power
Over frequency
Under frequency
Over current
Over current earth fault
Over current N-phase
Phase unbalance current
Demand current
Under voltage
Phase unbalance voltage
Over voltage
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
76
Function Manual, 11/2008, A5E02316914A-01
Maintenance – maintenance 1 tab (MAINTENANCE_1)
(1)
N_SC_TRP
(2)
N_OVL_TRP
(3)
N_EF_TRP
(4)
S_I2T_L2
(5)
S_I2T_N
(6)
RD_DR91
(7)
OP_HOURS
(8)
N_ACT_CC
(9)
S_I2T_L3
(10)
S_I2T_L1
(11)
N_ACT_TRP
(12)
N_ACT_LD
(13)
MAINT_MC
Figure 3-12
Faceplate for maintenance view, maintenance 1 tab
Element (parameters)
Meaning
Display when 3WL is connected
following Y-link
MAINT_MC
Maintenance information on the main contacts
No
N_ACT_LD
Number of switches under load
No
N_ACT_TRP
Number of switches caused by trips
No
N_SC_TRP
Number of short-circuit releases (SI)
No
N_OVL_TRP
Number of overload trips (L)
No
N_EF_TRP
Number of ground-fault trips (G)
No
S_I2T_L1
Total of deactivated I2t values L1
No
S_I2T_L2
Total of deactivated I2t values L2
No
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
77
Element (parameters)
Meaning
Display when 3WL is connected
following Y-link
S_I2T_L3
Total of deactivated I2t values L3
No
S_I2T_N
Total of deactivated I2t values N
No
N_ACT_CC
Switching cycle counter (for On / Off switching cycle)
No
OP_HOURS
Operating hours counter (when On + current > 0)
No
RD_DR91
Read maintenance information (data record 91)
No
Maintenance – maintenance 2 tab ((MAINTENANCE_2)
(1)
RD_DR91
(2)
CON_MOD
Figure 3-13
Faceplate for maintenance view, maintenance 2 tab
Element (parameters)
Meaning
Display when 3WL is
connected following Y-link
CON_MOD
Modules which are connected to the cubicle bus
No
RD_DR91
Read maintenance information (data record 91)
No
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
78
Function Manual, 11/2008, A5E02316914A-01
Possible modules
COM15
Trip unit ETU
ZSI Module
Config. dig. output module
Dig. output module #2
Dig. input module #2
Breaker Status Sensor BSS
Dig. output module #1
Dig. input module #1
BDA or BDA Plus
Grafic display ETU76B
Analog output module #2
Analog output module #1
Metering or Metering Plus
When the relevant bit is set, the corresponding text is displayed in the faceplate. Otherwise
the field remains empty.
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
79
Maintenance – operation tab (MAINTENANCE_OP)
(1)
MAINT
(2)
R_MAINT
(3)
ACK_TRIP
(4)
DEL_TRIP
(5)
R_VAL_MEM
(6)
R_TEMP
Figure 3-14
Faceplate for maintenance view, operation tab
Element (parameters)
Meaning
Display when 3WL is
connected following Y-link
MAINT
Maintenance mode active / inactive
No
R_MAINT
Reset all maintenance information and counters which can be
reset
No
ACK_TRIP
A tripping operation currently active is acknowledged and
reset
No
DEL_TRIP
Delete tripping and event log
No
R_VAL_MEM
Reset all min./max. value memories
(apart from temperature)
No
R_TEMP
Reset minimum / maximum temperatures
No
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
80
Function Manual, 11/2008, A5E02316914A-01
Protect. para – parameter set A tab (PARA_SET_A)
(1)
I4T_OVLD_PROT_A
(2)
PH_L_SEN_A
(3)
THERM_MEM_A
(4)
I2T_D_STRIP_A
(5)
OV_LD_N_A
(6)
T_EFLT_A
(7)
T_EFLT2_A
(8)
RD_DR129
(9)
I2T_EFLT_PROT_A
(10)
E_FLT_PROT2_A
(11)
E_FLT_PROT_A
(12)
IN_PRO_PARA_A
(13)
T_STRIP_A
(14)
SHORT_D_PROT_A
(15)
TL_CL_A
(16)
THERM_T_A
(17)
OV_LD_A
Figure 3-15
Faceplate for protect. para view, parameter set A
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
81
Element (parameters)
Meaning
Display when 3WL is
connected following Y-link
OC_LD_A
Overload parameter IR parameter set A (PS A)
No
THERM_T_A
Cooling time constant PS A
No
TL_CL_A
Time-lag class tR PS A
No
SHORT_D_PROT_A
Short-circuit protection delayed Isd PS A
No
T_STRIP_A
Delay time for short-circuit protection tsd PS A
No
IN_PRO_PARA_A
Short-circuit protection instantaneous Isd PS A
No
E_FLT_PROT_A
Ground-fault protection Ig1 PS A
No
E_FLT_PROT2_A
Ground-fault protection Ig2 PS A
No
I2T_EFLT_PROT_A
I2t characteristic for ground-fault protection PS A
No
I4T_OVLD_PROT_A
I4t characteristic for overload protection PS A
No
PH_L_SEN_A
Phase loss sensitivity PS A
No
THERM_MEM_A
Thermal memory PS A
No
I2T_D_STRIP_A
I2t characteristic for delayed ground-fault protection PS A No
OV_LD_N_A
Overload protection neutral conductor IN PS A (WL)
No
T_EFLT_A
Delay time for ground fault tg1 PS A
No
T_EFLT2_A
Delay time for ground fault tg2 PS A
No
RD_DR129
Read protect. para (data record 129)
No
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
82
Function Manual, 11/2008, A5E02316914A-01
Protect. para – parameter set B tab (PARA_SET_B)
(1)
I4T_OVLD_PROT_B
(2)
PH_L_SEN_B
(3)
THERM_MEM_B
(4)
I2T_D_STRIP_B
(5)
OV_LD_N_B
(6)
T_EFLT_B
(7)
T_EFLT2_B
(8)
RD_DR129
(9)
I2T_EFLT_PROT_B
(10)
E_FLT_PROT2_B
(11)
E_FLT_PROT_B
(12)
IN_PRO_PARA_B
(13)
T_STRIP_B
(14)
SHORT_D_PROT_B
(15)
TL_CL_B
(16)
THERM_T_B
(17)
OV_LD_B
Figure 3-16
Faceplate for protect. para view, parameter set B
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
83
Element (parameters)
Meaning
Display when 3WL is
connected following Y-link
OC_LD_B
Overload parameter IR parameter set B (PS B)
No
THERM_T_B
Cooling time constant PS B
No
TL_CL_B
Time-lag class tR PS B
No
SHORT_D_PROT_B
Short-circuit protection delayed Isd PS B
No
T_STRIP_B
Delay time for short-circuit protection tsd PS B
No
IN_PRO_PARA_B
Short-circuit protection instantaneous Isd PS B
No
E_FLT_PROT_B
Ground-fault protection Ig1 PS B
No
E_FLT_PROT2_B
Ground-fault protection Ig2 PS B
No
I2T_EFLT_PROT_B
I2t characteristic for ground-fault protection PS B
No
I4T_OVLD_PROT_B
I4t characteristic for overload protection PS B
No
PH_L_SEN_B
Phase loss sensitivity PS B
No
THERM_MEM_B
Thermal memory PS B
No
I2T_D_STRIP_B
I2t characteristic for delayed ground-fault protection PS B No
OV_LD_N_B
Overload protection neutral conductor IN PS B (WL)
No
T_EFLT_B
Delay time for ground fault tg1 PS B
No
T_EFLT2_B
Delay time for ground fault tg2 PS B
No
RD_DR129
Read protect. para (data record 129)
No
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
84
Function Manual, 11/2008, A5E02316914A-01
Protect. para – additional tab (PROTPARA_ADD)
(1)
ACT_PARA
(2)
EARTH_FLT_CUR
(3)
LD_SHED
(4)
LD_REST
(5)
T_SHED_REST
(6)
RD_DR129
(7)
RD_DR69
(8)
STOFF_GFON
(9)
STON_GFOFF
Figure 3-17
Faceplate for protect. para view, additional tab
Element (parameters)
Meaning
Display when 3WL is
connected following Y-link
ACT_PARA
Active parameter set
No
LD_SHED
Load shedding warning
No
LD_REST
Load restorage
No
T_SHED_REST
Delay time for load shedding / restorage
No
EARTH_FLT_CUR
Type of ground fault detection
No
STON_GFOFF
ZSI short-circuit
No
STOFF_GFON
ZSI ground fault
No
RD_DR69
Read ZSI parameter (data record 69)
No
RD_DR129
Read protect. para (data record 129)
No
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
85
Ext. protect. para – current tab (EXTPROTPARA_CUR)
(1)
T_PH_U_CUR
(2)
T_THD_CUR
(3)
CUR_TRNS_LIM
(4)
RD_DR128
(5)
THD_CUR
(6)
PH_UNBL_CUR
Figure 3-18
Faceplate for ext. protect. para view, current tab
Element (parameters)
Meaning
Display when 3WL is
connected following Y-link
PH_UNBL_CUR
Current unbalance
No
THD_CUR
THD of current
No
T_PH_U_CUR
Delay time for current unbalance
No
T_THD_CUR
Delay time of THD of current
No
RD_DR128
Read ext. protect. para (data record 128)
No
CUR_TRNS_LIM
Lower limit of current transfer
No
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
86
Function Manual, 11/2008, A5E02316914A-01
Ext. protect. para – voltage tab (EXTPROTPARA_VOLT)
(1)
T_PH_U_V
(2)
T_UN_VOLT
(3)
T_OV_VOLT
(4)
RD_DR128
(5)
PH_ROT
(6)
OVER_VOLT
(7)
UNDER_VOLT
(8)
PH_UNBAL_VOLT
Figure 3-19
Faceplate for ext. protect. para view, voltage tab
Element (parameters)
Meaning
Display when 3WL is
connected following Y-link
PH_UNBAL_VOLT
Voltage unbalance
No
UNDER_VOLT
Under voltage
No
OVER_VOLT
Over voltage
No
PH_ROT
Phase direction of rotation
No
T_PH_U_V
Delay time for voltage unbalance
No
T_UN_VOLT
Delay time for under voltage
No
T_OV_VOLT
Delay time for over voltage
No
RD_DR128
Read ext. protect. para (data record 128)
No
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
87
Ext. protect. para – active power tab (EXTPROTPARA_ACT_POW)
(1)
T_RP_NORM
(2)
T_RP_REV
(3)
RD_DR128
(4)
RP_REV
(5)
RP_NORM
Figure 3-20
Faceplate for ext. protect. para view, reactive power tab
Element (parameters)
Meaning
Display when 3WL is connected
following Y-link
RP_NORM
Real power in normal direction
No
RP_REV
Real power in reverse direction
No
T_RP_NORM
Delay time for active power in normal direction
No
T_RP_REV
Delay time for active power in reverse direction
No
RD_DR128
Read ext. protect. para (data record 128)
No
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
88
Function Manual, 11/2008, A5E02316914A-01
Ext. protect. para – frequency tab (EXTPROTPARA_FREQ)
(1)
T_UN_FRQ
(2)
T_OV_FRQ
(3)
RD_DR128
(4)
OV_FRQ
(5)
UNDER_FRQ
Figure 3-21
Faceplate for ext. protect. para view, frequency tab
Element (parameters)
Meaning
Display when 3WL is connected
following Y-link
UNDER_FRQ
Under frequency
No
OV_FRQ
Over frequency
No
T_UN_FRQ
Delay time for under frequency
No
T_OV_FRQ
Delay time for over frequency
No
RD_DR128
Read ext. protect. para (data record 128)
No
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
89
Setpoints – current tab (SETPOINTS_CUR)
(1)
T_CUR_OVER_I
(2)
T_CUR_GRD_I
(3)
T_CUR_N_I
(4)
T_UNBAL_CUR_I
(5)
T_CUR_DEM_I
(6)
T_CUR_THD_I
(7)
WR_DR130
(8)
RD_DR130
(9)
CUR_THD_I
(10)
CUR_DEM_I
(11)
UNBAL_CUR_I
(12)
CUR_N_I
(13)
CUR_GRD_I
(14)
CUR_OVER_I
Figure 3-22
Faceplate for setpoints view, current tab
Element (parameters)
Meaning
Display when 3WL is
connected following Y-link
CUR_OVER_I
Over current
No
CUR_GRD_I
Current which flows to earth
No
CUR_N_I
Over current in neutral conductor
No
UNBAL_CUR_I
Phase unbalance current
No
CUR_DEM_I
Demand of current
No
CUR_THD_I
THD current
No
T_CUR_OVER_I
Delay time for over current
No
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
90
Function Manual, 11/2008, A5E02316914A-01
Element (parameters)
Meaning
Display when 3WL is
connected following Y-link
T_CUR_GRD_I
Delay time of current which flows to earth
No
T_CUR_N_I
Delay time for over current in neutral conductor
No
T_UNBAL_CUR_I
Delay time for phase imbalance Current
No
T_CUR_DEM_I
Delay time for demand of current
No
T_CUR_THD_I
Delay time for THD current
No
RD_DR128
Read setpoints (data record 130)
No
WR_DR128
Write setpoints (data record 130)
No
Setpoints – voltage tab (SETPOINTS_VOLT)
(1)
T_UNDER_VOLT_I
(2)
T_OVER_VOLT_I
(3)
T_UNBAL_VOLT_I
(4)
T_VOLT_THD_I
(5)
T_CREST_F_I
(6)
T_FORM_F_I
(7)
WR_DR130
(8)
RD_DR130
(9)
FORM_F_I
(10)
CREST_F_I
(11)
VOLT_THD_I
(12)
UNBAL_VOLT_I
(13)
OVER_VOLT_I
(14)
UNDER_VOLT_I
Figure 3-23
Faceplate for setpoints view, voltage tab
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
91
Element (parameters)
Meaning
Display when 3WL is
connected following Y-link
UNDER_VOLT_I
Under voltage
No
OVER_VOLT_I
Over voltage
No
UNBAL_VOLT_I
Phase unbalance voltage
No
VOLT_THD_I
THD voltage
No
CREST_F_I
Crest factor
No
FORM_F_I
Form factor
No
T_UNDER_VOLT_I
Delay time for under voltage
No
T_OVER_VOLT_I
Delay time for over voltage
No
T_UNBAL_VOLT_I
Delay time for phase imbalance Voltage
No
T_VOLT_THD_I
Delay time for THD voltage
No
T_CREST_F_I
Delay time for crest factor
No
T_FORM_F_I
Delay time for the form factor
No
RD_DR128
Read setpoints (data record 130)
No
WR_DR128
Write setpoints (data record 130)
No
Setpoints – frequency tab (SETPOINTS_FREQ)
(1)
T_UNDER_FRQ_I
(2)
T_OVER_FRQ_I
(3)
WR_DR130
(4)
RD_DR130
(5)
OVER_FRQ_I
(6)
UNDER_FRQ_I
Figure 3-24
Faceplate for setpoints view, frequency tab
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
92
Function Manual, 11/2008, A5E02316914A-01
Element (parameters)
Meaning
Display when 3WL is
connected following Y-link
UNDER_FRQ_I
Under frequency
No
OVER_FRQ_I
Over frequency
No
T_UNDER_FRQ_I
Delay time for under frequency
No
T_OVER_FRQ_I
Delay time for over frequency
No
RD_DR128
Read setpoints (data record 130)
No
WR_DR128
Write setpoints (data record 130)
No
Setpoints – active power tab (SETPOINTS_ACT_POW)
(1)
T_RP_NORM_I
(2)
T_RP_REV_I
(3)
T_PF_CAP_I
(4)
T_PF_IND_I
(5)
T_RP_DEM_I
(6)
WR_DR130
(7)
RD_DR130
(8)
RP_DEM_I
(9)
PF_IND_I
(10)
PF_CAP_I
(11)
RP_REV_I
(12)
RP_NORM_I
Figure 3-25
Faceplate for setpoints view, active power tab
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
93
Element (parameters)
Meaning
Display when 3WL is connected
following Y-link
RP_NORM_I
Real power in normal direction
No
RP_REV_I
Real power in reverse direction
No
PF_CAP_I
Power factor, capacitive
No
PF_IND_I
Power factor, inductive
No
RP_DEM_I
Demand real power
No
T_RP_NORM_I
Delay time for active power in normal direction
No
T_RP_REV_I
Delay time for active power in reverse direction
No
T_PF_CAP_I
Delay time for power factor, capacitive
No
T_PF_IND_I
Delay time for power factor, inductive
No
T_RP_DEM_I
Delay time for demand of active power
No
RD_DR128
Read setpoints (data record 130)
No
WR_DR128
Write setpoints (data record 130)
No
Description of blocks
3.2 Driver module DRV_3WL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
94
Function Manual, 11/2008, A5E02316914A-01
Setpoints – apparent/reactive power tab (SETPOINTS_APP_REACT_POW)
(1)
T_AP_I
(2)
T_RAP_NORM_I
(3)
T_RAP_REV_I
(4)
T_AP_DEM_I
(5)
T_RAP_DEM_I
(6)
WR_DR130
(7)
RD_DR130
(8)
RAP_DEM_I
(9)
AP_DEM_I
(10)
RAP_REV_I
(11)
RAP_NORM_I
(12)
AP_I
Figure 3-26
Faceplate for setpoints view, apparent/reactive power tab
Element (parameters)
Meaning
Display when 3WL is
connected following Y-link
AP_I
Apparent power
No
RAP_NORM_I
Reactive power in normal direction
No
RAP_REV_I
Reactive power in reverse direction
No
AP_DEM_I
Demand apparent power
No
RAP_DEM_I
Demand reactive power
No
T_AP_I
Delay time for apparent power
No
T_RAP_NORM_I
Delay time for reactive power in normal direction
No
T_RAP_REV_I
Delay time for reactive power in reverse direction
No
T_AP_DEM_I
Delay time for demand of apparent power
No
Description of blocks
3.3 Driver module DRV_3VL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
95
Element (parameters)
Meaning
Display when 3WL is
connected following Y-link
T_RAP_DEM_I
Delay time for demand of reactive power
No
RD_DR128
Read setpoints (data record 130)
No
WR_DR128
Write setpoints (data record 130)
No
Message suppression
(1)
SUP_LD_SHED
(2)
SUP_WRN
(3)
SUP_SP_EXCEED
(4)
SUP_OVLD_WRN
Figure 3-27
Faceplate for message suppression view
Element (parameters)
Meaning
Display when 3WL is
connected following Y-link
SUP_OVLD_WRN
Message ("Overload warning present") is not output
Yes
SUP_SP_EXCEED
Message ("An active setpoint has been exceeded") is not
output
Yes
SUP_WRN
Message ("There is currently a warning message present")
is not output
Yes
SUP_LD_SHED
Message ("Load shedding warning") is not output
Yes
3.3
Driver module DRV_3VL
FB1740
Description of blocks
3.3 Driver module DRV_3VL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
96
Function Manual, 11/2008, A5E02316914A-01
Description of block:
● Calling OBs (Page 96)
● Called blocks (Page 96)
● Function (Page 96)
● Message behavior (Page 99)
● Assignment of the cyclic process image (Page 100)
● Addressing and module driver (Page 101)
● Processing the diagnostics data of the 3VL device (Page 102)
● Start-up characteristics (Page 102)
● Block parameters (Page 102)
● Description of symbols and faceplates (Page 111)
See also
Diagnostics block DIA_WLVL (Page 17)
Driver module DRV_3WL (Page 22)
3.3.1
Calling OBs
The OB watchdog interrupt in which the block is installed (e.g. OB32). Also in OB100
(performed automatically in CFC, see start-up characteristics).
3.3.2
Called blocks
The block calls the following blocks:
SFB35
ALARM_8P
SFB52
RDREC
SFB53
WRREC
SFC1
READ_CLK
SFC6
RD_SINFO
SFC20
BLKMOV
SFC21
FILL
3.3.3
Function
The DRV_3VL block is used for measurement acquisition and control and it forms the
interface to the OS.
Description of blocks
3.3 Driver module DRV_3VL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01
97
Automatic / manual mode switch over
Automatic and manual mode are available for operating the driver block. When in manual
mode, the user can control the circuit breaker position (ON / OFF) of the faceplate in WinCC.
When in automatic mode, the corresponding buttons are locked (cannot be operated) in the
faceplate and the circuit breaker is controlled by input parameters which can be connected in
the CFC (AUTO_ON / AUTO_OFF) and therefore by the AS program.
NOTICE
If an error occurs (monitoring error, Local turn off, Tripped) the block changes to Forced
manual. If the pending error state is acknowledged with one of the RESET buttons, the
block goes into the specified mode again.
If Automatic mode is specified by the AS program (LIOP_SEL = 1, AUT_L = 1) the
commands present at AUTO_ON or AUTO_OFF are always output.
Under certain circumstances this means that resetting error states may cause a switching
operation of the circuit breaker. If this is not desired the user must configure the AS
program accordingly.
Switching the circuit breaker on/off
The user can use the driver block to switch the circuit breaker.
It is important to note here that the ON state means "main contacts closed" and the OFF
state means "main contacts open".
The circuit breaker cannot be switched on or off in certain states:
It must not be switched on when:
• there is a monitoring error
(QMON_ERR = 1)
• the block is in maintenance mode
(MAINT = 1)
• write protection applies
(QWR_PROT = 1)
• the circuit breaker is already on
(QON = 1)
• the circuit breaker has tripped
(QTRIP = 1)
• the circuit breaker has been switched off locally
(QLOC_OFF = 1)
It must not be switched off when:
• there is a monitoring error
(QMON_ERR = 1)
• the block is in maintenance mode
(MAINT = 1)
• write protection applies
(QWR_PROT = 1)
• the circuit breaker is already off
(QOFF = 1)
• the circuit breaker has tripped
(QTRIP = 1)
• the circuit breaker has been switched off locally
(QLOC_OFF = 1)
Description of blocks
3.3 Driver module DRV_3VL
Library SENTRON 3WL / 3VL for SIMATIC PCS 7
98
Function Manual, 11/2008, A5E02316914A-01
Resetting Tripped and Local turn off states
If the block is in one of the two states, it has to be reset before an On command can be
output again. The faceplate features a corresponding button for the user for this RESET.
CAUTION
Before the circuit breaker is switched back on, the reason for tripping/switching off must be
established and possible error causes must be rectified.
NOTICE
If such a state is reset the response of the mode must be observed as it may cause a
switching operation of the circuit breaker under certain circumstances.
See Automatic / Manual mode switchover
Feedback monitoring
When monitoring is activated (MONITOR = On), switching commands (ON / OFF) and the
resetting of trips are time monitored. If the expected state is not reached after an operation
and within the monitoring time (TIME_MON), the block outputs a message and goes into a
resetting state (QMON_ERR).
The faceplate features an appropriate RESET button for resetting this state again.
NOTICE
If the monitoring error is reset the response of the mode must be observed as it may cause
a switching operation of the circuit breaker under certain circumstances.
See Automatic / Manual mode switchover
Measured value acquisition
The block reads measured values from the cyclic process image.
When operating 3VL on the DP master system directly, the block also reads data record 94
with the system function block RDREC (SFB52).
The data record is read in a defined cycle. The interval at which the data record can be read
can be set in seconds using the input parameter CYCLE_T. The default setting is 60
seconds. A cycle of 0 seconds or less means that this data record is not read.
Time synchronization
Data record 68 writes the current time in cycles in order to transfer the current time to the
circuit breaker. This cycle can be set in seconds using the TIME_SYNC_T parameter.
