Atlona AT-PRO3HD66M Operation & User’s Manual

6 by 6 Matrix Switcher AT-PRO3HD66M atlona.com Toll free: 1-877-536-3976 Local: 1-408-962-0515

Local: 1-408-962-0515 1. Introduction ...................................................................................... 3 2. Package Contents ...................................................................................... 3 3. Features ...................................................................................... 3 4. Before You Start ...................................................................................... 3 5. Panel Descriptions • Front Panel ...................................................................................... 4 • IR ...................................................................................... 4 • Back Panel ...................................................................................... 5 6. Connection and Installation • 3rd Party Control ...................................................................................... 6 • IR Remote Control ...................................................................................... 7 • Matrix I/O Control ...................................................................................... 8 • I/O Route Memory ...................................................................................... 9 • EDID .................................................................................. 9-11 • Matrix Status ..................................................................................... 12 7. RS-232 • Connection ..................................................................................... 13 • Set Up ..................................................................................... 13 8. TCP/IP • RS-232 TCP/IP Set Up ..................................................................................... 14 • LAN TCP/IP Set Up .................................................................................14-15 • WebGUI .................................................................................15-22 9. TCP/IP and RS-232 Control • Commands ...................................................................................... 23 • TCP/IP Commands ..................................................................................23-24 • Baud Rate ..................................................................................24-25 10. Remote Control ..................................................................................... 25 11. Resetting and Updating ..................................................................................... 26 12. Specifications ..................................................................................... 27 13. Safety Information ..................................................................................... 28 14. Warranty ..................................................................................... 29 15. Atlona Product Registration ..................................................................................... 30 Table of Contents

Local: 1-408-962-0515 Introduction With the latest and more affordable HDBaseT® technology extend HDMI® sources up to 230ft over category cable. The Atlona HDMI 6 by 6 Matrix Switcher allows for effortless control of up to 12 devices through IR, RS-232, TCP/IP and the front panel. With built in S/PDIF ports send audio to an AVR or distribution amp. To ensure all audio passes through, the 6 by 6 Matrix Switcher supports all Lossy and Lossless formats of Dolby® and DTS™ over HDMI. Package Contents Features • 1 x AT-PRO3HD66M • 1 x 24V/6.25A DC adaptor • 1 x Power cord • 1 x IR Extender • 7 x IR Emitter • 1 x Remote control • 1 x Pair of dual purpose wall/rack mounts • 1 x User Manual • HDBaseT allows IR, RS-232, audio and visual signals to pass over a single category cable. • Latest feature of Power over Category cable (PoCc™) enables the matrix to power all compatible receivers. • IR ports for zone dedicated control through IR remote control and 3rd party control boxes. • Programmable I/O memories, save I/O routes for faster switching to the most commonly used configurations. • EDID™ learning function for up to 6 video display EDIDs. • Built in internal EDID mode provides 12 individual EDIDs to ensure compatibility when using DVI projectors or trying to route digital multi-channel audio through an S/PDIF port • Multiple control options such as RS-232, IR, TCP/IP, and the front panel. • Dolby® TrueHD and DTS-HD Master Audio™ pass through HDMI output interface. • Compatible with DVI/D (with DVI/D to HDMI adapter such as AT14050), allowing DVI/D to be passed to displays. • Mirrored HDMI outputs on zones 5 and 6 for in room displays or AVRs • Built in S/PDIF audio de-embedding for AVR or audio distribution amplifiers. Compatible with PCM 2Channel, Dolby 2.0, Dolby Digital 5.1, and DTS 5.1. • Optional redundant power supply (AT-PW24V6.25A) in case the main power supply fails. • HDCP compliant Before You Start • Make sure when connecting a category cable a 568B termination method is used. • Make sure the matrix is connected to a component surge suppressor with line conditioning. Note: Atlona’s warranty does not cover damage due to electrical disturbances. A component surge suppressor with line conditioning is highly suggested, especially in areas with electrical storms. • Be sure you’re using a mono to mono (2 conductor) 3.5mm IR cable when using IR output control from 3rd party control boxes, stereo (3 conductor) 3.5mm cables are not compatible.

Local: 1-408-962-0515 DC 24V BACKUP MAIN ZONE 1 ZONE 2 ZONE 3 ZONE 4 ZONE 5 ZONE 6 MATRIX OUT RS-232 FW LAN HDMI IN HDMI OUT HDMI OUT MATRIX IN IR IN IR OUT COAX OUT CAT5e/6/7 IR IN IR OUT COAX OUT CAT5e/6/7 IR IN IR OUT COAX OUT CAT5e/6/7 IR IN IR OUT COAX OUT CAT5e/6/7 IR IN IR OUT CAT5e/6/7 IR IN IR OUT CAT5e/6/7 1 2 3 4 5 6 AT-PRO3HD66M AT-PRO3HD66M 1 2 3 4 5 6 EDID IR INFO DEFAULT ALL MEMORY FCN CANCEL POWER ENTER B M Panel Description Front Panel 1. Power Button - Cycles the power between On (blue backlight) or Standby (red backlight) mode. 2. Enter Button - Use to view current status for inputs and outputs or to confirm a command. 3. IR Receiver Window - Receives the signal from the included IR Remote Control or a 3rd party control box. 4. Function Button - Select for command options. (blue backlight when selected) a. Default: Mirrors all inputs to corresponding outputs. (i.e. 1 to 1, 2 to 2, 3 to 3, etc.) b. All: Save a single input to all the outputs with this function c. Memory: Save/load the current input and output route to memory d. EDID: Save/Load EDIDs to individual inputs e. IR: Turn IR receiving on/off (see below) f. INFO: Displays the firmware version on the front display 5. Cancel Button - Within the functions menu use to go back one screen or to the home screen. Note: You cannot power off or change functions unless you return to the home screen. 6. Number buttons - Use these buttons to select input and output paths or use with the function button to change matrix settings. 3 4 2 a b c d e f 1 5 6 The IR receiver window can sometimes pick up stray reflected IR commands causing loss of functionality. To disable the front panel, see directions below: IR ---> ---> ---> AT-PRO3HD66M Select Input Number home screen Select Function Option -------------------- ---> Select IR 1:On 2: Off Current: On/Off Select IR 1: On 2: Off Current On Select IR 1: On 2: Off Current off ---> ---> ---> ---> ---> ---> Feedback= ”IR On Selected” Feedback= ”IR Off Selected”

Local: 1-408-962-0515 DC 24V BACKUP MAIN ZONE 1 ZONE 2 ZONE 3 ZONE 4 ZONE 5 ZONE 6 MATRIX OUT RS-232 FW LAN HDMI IN HDMI OUT HDMI OUT MATRIX IN IR IN IR OUT COAX OUT CAT5e/6/7 IR IN IR OUT COAX OUT CAT5e/6/7 IR IN IR OUT COAX OUT CAT5e/6/7 IR IN IR OUT COAX OUT CAT5e/6/7 IR IN IR OUT CAT5e/6/7 IR IN IR OUT CAT5e/6/7 1 2 3 4 5 6 AT-PRO3HD66M AT-PRO3HD66M 1 2 3 4 5 6 EDID IR INFO DEFAULT ALL MEMORY FCN CANCEL POWER ENTER B M Back Panel 1. Firmware Update - Type B USB Port used for updating matrix firmware 2. RS-232 - Connect to this port for control from a computer or 3rd party control box. 3. Matrix IR In - Used to control matrix I/O switching from a 3rd party IR control box. 4. Matrix IR Out - Global output, combines IR for all incoming zones. 5. Zone dedicated ports a. IR 3.5mm mono In ports: Used in conjunction with 3rd party IR control box to extend IR control commands to video displays over category cable. Note: Be sure you’re using a mono to mono 3.5mm IR cable for 3rd party control boxes, 3.5mm stereo cables are not compatible. b. IR Out ports: Sends IR signal to sources through a 3.5mm IR emitter c. Coax Out (S/PDIF): Audio de-embedding for distribution amplifiers and AVRs. Compatible with PCM 2Channel, Dolby 2.0, Dolby Digital 5.1, and DTS 5.1. d. CAT5e/6/7 Out (RJ45): Extends video and bidirectional RS-232, IR, and audio signals through a single category cable. e. HDMI Out: Mirrored HDMI output 6. Main Power Port - Use included locking DC adaptor to power the matrix switcher 7. LAN Port - For TCP/IP matrix control 8. HDMI Input Ports - Connect HDMI sources into these ports, such as DVD players, Blu-ray players, computers, etc. 9. Back Up Power Port - Redundant power supply (AT-PW24V6.25A available at atlona.com) 1 2 3 4 7 8 a b c e d 9 6 5

Local: 1-408-962-0515 NO NC COM NO NC COM NO NC COM NO NC COM GND SIG +12V GND SIG +12V GND SIG +12V GND SIG +12V 1 2 3 4 RELAYS WIFI 2 ZIGBEE 12V DC IR OUT ID FACTORY RESTORE SERIAL 1 SERIAL 2 HDMI COMPONENT VIDEO OUT ETHERNET CONTACTS AUDIO OUT AUDIO IN WIFI 1 eSATA USB DIGITAL COAX OUT 1 2 3 4 5 6 L R DC 24V BACKUP MAIN ZONE 1 ZONE 2 ZONE 3 ZONE 4 ZONE 5 ZONE 6 MATRIX OUT RS-232 FW LAN HDMI IN HDMI OUT HDMI OUT MATRIX IN IR IN IR OUT COAX OUT CAT5e/6/7 IR IN IR OUT COAX OUT CAT5e/6/7 IR IN IR OUT COAX OUT CAT5e/6/7 IR IN IR OUT COAX OUT CAT5e/6/7 IR IN IR OUT CAT5e/6/7 IR IN IR OUT CAT5e/6/7 1 2 3 4 5 6 AT-PRO3HD66M AT-PRO3HD66M 1 2 3 4 5 6 EDID IR INFO DEFAULT ALL MEMORY FCN CANCEL POWER ENTER B M RS232 OUT IR OUT HDMI OUT CAT5/6 IN LINK IR IN Connection and Installation 3rd Party Controller Video Display 3rd Party Control box Set Up IR Emitter Front Panel IR Receiver IR Emitter AT-PRO3HDREC Zone IR Control Matrix IR Control With the feature of the IR input zone ports the AT-PRO3HD66M has the ability to receive IR commands from a 3rd party controller and send it out through the CAT5e/6/7 port to control the displays in any zone. Blu-ray Player FCN CANCEL POWER ENTER B

Local: 1-408-962-0515 RS232 OUT IR OUT HDMI OUT CAT5/6 IN LINK IR IN Note: IR signal is routed through the HDBaseT zone. Only the IR out of the corresponding zone will pass control signal when using a 3rd party IR controller IR Remote Control Set Up DC 24V BACKUP MAIN ZONE 1 ZONE 2 ZONE 3 ZONE 4 ZONE 5 ZONE 6 MATRIX OUT RS-232 FW LAN HDMI IN HDMI OUT HDMI OUT MATRIX IN IR IN IR OUT COAX OUT CAT5e/6/7 IR IN IR OUT COAX OUT CAT5e/6/7 IR IN IR OUT COAX OUT CAT5e/6/7 IR IN IR OUT COAX OUT CAT5e/6/7 IR IN IR OUT CAT5e/6/7 IR IN IR OUT CAT5e/6/7 1 2 3 4 5 6 AT-PRO3HD66M AT-PRO3HD66M 1 2 3 4 5 6 EDID IR INFO DEFAULT ALL MEMORY FCN CANCEL POWER ENTER B M Video Display IR Remote IR Receiver Module Blu-ray Player IR Emitter AT-PRO3HDREC

Local: 1-408-962-0515 I/O Control The AT-PRO3HD66M’s front panel has 3 functions: I/O control, EDID, and matrix settings. The following sections go over step by step setup & control. (I.E. Input 1 to output 2) (I.E. Input 1 to output 1, input 2 to output 2, etc.) (I.E. Input 1 to output 1, 2, 3, 4, 5 and 6) To set an input to an output To mirror all inputs and outputs To route one input to all outputs Feedback =”Input # saved to Output #” Feedback =”Mirroring In and Out” Feedback = ”Input # saved to all” Matrix Front Panel Functions ---> ---> ---> ---> ---> ---> ---> ---> ---> ---> ---> ---> ---> ---> ---> ---> ---> ---> ---> ---> AT-PRO3HD66M Select Input Number AT-PRO3HD66M Select Input Number AT-PRO3HD66M Select Input Number Select Function Option Select Function Option Select input number to save to all outputs Input # to all outputs Press enter to confirm Mirror In to Out Press enter to confirm Select output number Press enter to confirm home screen input selection input selection output selection home screen home screen through through through

Local: 1-408-962-0515 To save an I/O route to memory To load a saved I/O route Feedback = ”Memory # saved” Feedback = ”Memory # loaded” ---> ---> ---> ---> ---> ---> ---> ---> ---> ---> ---> ---> ---> ---> ---> ---> ---> ---> AT-PRO3HD66M Select Input Number AT-PRO3HD66M Select Input Number Select Function Option Select Function Option 1 Save in/out route 2 Select memory route 1 Save in/out route 2 Select memory route Save to memory (1-6) # Press enter Select Memory route 1-6 Press enter to load home screen home screen memory selection memory selection Once inputs and outputs have been set they can be saved to memory and recalled later. Up to 6 individual input/output routes can be saved. The route will remain in memory until a new route has been saved to that memory number or the matrix has been factory reset. Once an input/output route has been saved, it can be loaded at any time. I/O Route Memory O: 1 2 3 4 5 6 I : 4 6 1 3 2 6 example route When the matrix is completely connected and turned on it will load the default EDID, which is the highest common native resolution of the devices. (i.e. In the diagram below the default would be 720p with 2ch audio. Multi-channel audio and 3D are not enabled on internal mode, unless all devices have these features.) EDID Set Up Output 2 Output 3 Input 2 1080p-Dolby TrueHD (3D) Input 1 Output 1 720p-2ch 720p-2ch 1080p (3D)-2ch 1080p-Dolby TrueHD (3D) DC 24V BACKUP MAIN ZONE 1 ZONE 2 ZONE 3 ZONE 4 ZONE 5 ZONE 6 MATRIX OUT RS-232 FW LAN HDMI IN HDMI OUT HDMI OUT MATRIX IN IR IN IR OUT COAX OUT CAT5e/6/7 IR IN IR OUT COAX OUT CAT5e/6/7 IR IN IR OUT COAX OUT CAT5e/6/7 IR IN IR OUT COAX OUT CAT5e/6/7 IR IN IR OUT CAT5e/6/7 IR IN IR OUT CAT5e/6/7 1 2 3 4 5 6 AT-PRO3HD66M AT-PRO3HD66M 1 2 3 4 5 6 EDID IR INFO DEFAULT ALL MEMORY FCN CANCEL POWER ENTER B M On default, all devices in the diagram will work at 720p. If a device is not syncing or a different resolution is required, internal EDID or EDID copy and load should resolve these issues. The PRO3HD66M can copy up to 6 EDIDs to memory. through through

Local: 1-408-962-0515 Step 1: copy an EDID ---> ---> ---> ---> AT-PRO3HD66M Select Input Number Select Function Option home screen 1 To copy up to 6 EDIDs 2 To choose input EDID ---> ---> Copy from output # Save to Memory (1-6) # Copy from output # Save to Memory (1-6) # Feedback= ”Saved port # EDID to Memory # [Failed/Passed]” ---> ---> ---> ---> ---> Before an EDID can be loaded to an input, it must first be copied to the matrix’s memory. Each display’s EDID can be saved individually to one of the matrix’s six preset EDID memories. memory selection output selection Step 2: load a copied EDID onto an input ---> ---> ---> ---> AT-PRO3HD66M Select Input Number Select Function Option home screen 1 To copy up to 6 EDIDs 2 To choose input EDID Input # Select an input port Input # Press Enter Current: Default Input: # Mode: 1.Default 2.Saved 3.Int Input: # Select saved EDID memory 1-6 (#) Use EDID memory # + enter _ _ _ ---> ---> Feedback = ”Save memory # EDID to input #” ---> ---> ---> ---> ---> ---> ---> ---> ---> ---> Atlona EDID - ATL Pioneer EDID - PIO Toshiba EDID - TSB EX. Once EDIDs have been copied to memory they can be loaded to a specific input. Note: (refer to the diagram on page 9) Using the EDID of output 3 with input 1 will enable 1080p, 3D, and Dolby TrueHD to pass. Output 2 will receive no audio or video and output 1 will receive no audio with these settings. memory selection input selection through through through through through

Local: 1-408-962-0515 Step 3: Load an internal EDID on an input ---> ---> ---> ---> AT-PRO3HD66M Select Input Number Select Function Option home screen Internal EDID options Front panel display readout 1 To copy up to 6 EDIDs 2 To choose input EDID Input # Select an input port Input # Press Enter Current: Default Input: # Mode: 1.Default 2.Saved 3.Int EDID Internal # + enter ATL _____ ____ ---> ---> Feedback = ”Saved Internal # To input #” 1 - Cycles through EDIDs in ascending order 2 - Cycles through EDIDs in descending order ---> ---> ---> ---> ---> ---> ---> ---> ---> If the first two steps don’t produce the correct resolution or audio configuration, the twelve internal EDIDs should resolve the issue. * Recommended EDID for use of an AVR ** Recommended EDID for use of the S/PDIF audio de-embedding *** Recommended EDID for use of DVI projectors EDID 1: 1080P 2CH audio ATL 1080P 2CH EDID 2: 1080P HD multi-channel audio 7.1* ATL 1080P Multi CH EDID 3: 1080P Dolby Digital 5.1** ATL 1080P DD EDID 4: 1080P 3D 2CH audio ATL 1080P 3D 2CH EDID 5: 1080P 3D HD multi-channel audio 7.1* ATL 1080P 3D Multi CH EDID 6: 1080P 3D Dolby Digital 5.1** ATL 1080P 3D DD EDID 7: 720P 2CH audio ATL 720P 2CH EDID 8: 720P Dolby Digital 5.1** ATL 720P DD EDID 9: 1280x800 RGB 2CH audio ATL 1280x800 RGB 2CH EDID 10: 1366x768 RGB 2CH audio ATL 1366x768 RGB 2CH EDID 11: 1080P DVI*** ATL 1080P DVI EDID 12: 1280x800 DVI*** ATL 1280x800 RGB DVI Internal EDID selection input selection RS-232 commands: To access the different EDIDs through RS-232 the following commands must be used. Command Feedback Description EDIDMSetX default EDIDMSetX default Sets the EDID of an input to the default EDID Ex. EDIDMset2 default - sets input 2 to default EDIDMSetX saveY EDIDMSetX saveY Sets the EDID of an input to the previously saved EDID memory Ex. EDIDMset1 save3 - sets input 1 to the EDID memory 3 EDIDMSetX intZ EDIDMSetX intZ Sets the EDID of an input to one of the internal EDIDs Ex. EDIDMset3 int6 - sets input 3 to the internal EDID - 1080p 3D Dolby Digital 5.1 through

Local: 1-408-962-0515 Matrix Status When installing or troubleshooting it’s important to verify settings, or be able to come back to a project and see how it was set up. The AT-PRO3HD66M matrix settings are viewable through the front panel display. View current I/O settings, firmware version, FPGA version, IP, and the baud rates of not just the matrix but extenders as well. ---> ---> ---> ---> ---> AT-PRO3HD66M Select Input Number AT-PRO3HD66M FW Ver: 0.X.XX AT-PRO3HD66M Select Input Number O 1 2 3 4 5 6 I x x x x x x Select Function Option home screen home screen View Firmware/Baud Rate/FPGA settings View current I/O settings AT-PRO3HD66M Console: X X X X AT-PRO3HD66M IP Addr: XXX.XXX.XXX.XXX AT-PRO3HD66M Port 1: X X X X AT-PRO3HD66M FPGA 1 Ver: 0.0.XX ---> ---> ---> ---> ---> ---> ---> Matrix Baud Rate IP Address Output Baud Rate FPGA Version ---> ---> ---> ---> ----------------------------------------------------------- 115200 8 None 1 OR 9600 8 ODD 0 Press 4 to cycle through the baud rates of each output port. Press 2 to cycle through IP, Netmask, Gateway, IP port, and MAC address EX.

Local: 1-408-962-0515 RS-232 Connection RS-232 is connected through a 9-pin female DB connector. Only pins 2, 3, and 5 are terminated. No. Pin Function 1 ---- Not used 2 Tx Transmit 3 Rx Receive 4 ---- Not used 5 Gnd Ground 6 ---- Not used 7 ---- Not used 8 ---- Not used 9 ---- Not used 1 2 3 4 5 9 8 7 6 Set Up To set up the RS-232 hyperterminal (if not using 3rd party software) use the following steps: 1. Connect the matrix to a PC using a 9pin to 9pin cable 2. Go to the Device manager folder (see picture A) 3. Find the Matrix COM port and right click with a mouse and select properties (see picture B) NOTE: If unsure which COM port is the matrix, unplug the 9pin cable and plug it back in. It will disappear and reappear on the COM port list. 4. Under the properties menu select the port settings tab and update the menu to the matrix default settings of: Bits Per Second: 115200, Data Bits: 8, Parity: None, Stop Bits: 1 and Flow Control: None. (see picture C) Set up is done and any hyperterminal program may be used to control the matrix now. A B C

Local: 1-408-962-0515 TCP/IP Warning!: Do not connect the matrix LAN port until the first steps have been followed. BEFORE YOU PLUG IN ANYTHING: Verify no other devices on the network have the IP of 192.168.1.10 (the matrix default is 192.168.1.10). (See page 12 to view the IP through the front panel) There are two ways to set TCP/IP control when any of the products on the network have the same IP address as the matrix: RS-232 or through LAN on a non networked computer. RS-232 TCP/IP Set up (Preferred) LAN TCP/IP Set up (If RS-232 is not available) Step 1: Follow RS-232 set up instructions on page 13 Step 2: Open Hyperterminal program Step 3: Verify DHCP is off Send command “IPDHCPsta” followed by a carriage return Feedback should be “DHCPoff” If DHCP is on use command “IPDHCPoff” to turn DHCP off Step 4: Change the current IP using the command “IPStatic 192.168.0.200 255.255.255.0 192.168.0.1” IP can be anything that system devices aren’t currently using. (200 is just an example) Step 5: (optional) Change the port using the command “IPPort 4400” followed by a carriage return 4400 is just an example. The port can be changed to what is needed/wanted The matrix is now ready to be used for TCP/IP control. The LAN cable may be connected now. Step 1: Connect LAN to a computer Step 2: Right click the network icon at the bottom right side of screen and open network and sharing center on PC (see picture A) Step 3: Select internet type connection/local area connection (see picture B) Step 4: Select properties (see picture C) Step 4: Select IP V.4 and press properties (see picture D) A B C D Router IP address

Local: 1-408-962-0515 Step 5: Change IP to 192.168.1.2 and Subnet: 255.255.255.0 (see picture E) Step 6: Press apply Step 7: Close internet type connection and launch WebGUI Type the default IP (192.168.1.10) a web browser Log in: Username: root Password: Atlona Step 8: If desired, change the network address information Step 9: Go back to your network settings and return the IP V.4 to the original settings (see below) Step 10: Continue with WebGUI E TCP/IP WebGUI Atlona has created an easy to use WebGUI for changing settings and controlling the matrix. To begin, type the IP address of the matrix into a web browser (as seen below) Important: If experiencing any stability issues, disable any anti-virus or firewall that may be interfering with network communication to the Matrix.

Local: 1-408-962-0515 A login screen will appear. For the first log in (and future admin changes) the username is “root” and password is “Atlona”. Note: The username cannot change, but the password can be changed (see page 19) The home screen will display the general software and firmware information. If the matrix is powered off the FPGA will not display (see above). Once the power is on it will display (see below). Note: When the matrix is turned off many fields within the WebGUI will not display information. Be sure the matrix is powered on for complete control.

Local: 1-408-962-0515 The network set up page will allow the IP information to be changed. When a change is made the screen will grey and the ability to save or cancel will display at the bottom (see below). Note: If DHCP is on, the IP cannot be configured. Note: Be sure to save all changes before moving to the next page

Local: 1-408-962-0515 The config page under status/setting will allow the zone output and matrix baud rates to be changed, as well as turning power and the IR receiving window on / off. A grey the screen will display the save and cancel options when making changes. Remember to save all settings before moving on to the next page. Note: All like fields can be changed during one edit.

Local: 1-408-962-0515 Adding, deleting, and updating users can also be done from the config page. User name changes can only be done by the admin. Admin user name is always “root” and default password is “Atlona”. Note: Only the admin password can be changed. The username will always remain “root” Note: Always remember to save settings before moving to the next page

Local: 1-408-962-0515 The I/O page allows input and output routes to be changed easily by drop down menu. Output All will route one selected input to all the outputs. Note: All routes can be changed while in the grey edit screen. Remember to save after all changes have been made.

Local: 1-408-962-0515 For compatibility, EDID configuration has been added. Each input has a drop down selection for internal, default, and saved EDIDs. Note: When saving an EDID to memory through the WebGUI, the output will save to the corresponding memory. Ex. Output 2 will only save to Memory 2 Internal EDIDs (see page 11) provide 12 options for video and audio to ensure compatibility and reliability. Auto default mode will choose the highest common video resolution and audio format. Each saved EDID will save to memory and be noted as MM and the number of its output. **Clicking on the Display’s EDID link will provide a breakdown of the selected output’s EDID Note: MM#s in the picture above are examples of saved EDIDs Note: Remember to save after all changes to ensure complete compatibility.

Local: 1-408-962-0515 The HDCP page will display the output’s ability to pass HDCP or not. Several messages will appear under different circumstances: Supported - HDCP is supported by the display Not Supported - The display is unable to support HDCP Non-HDCP Source - A source that does not support HDCP No connection - If no source is selected, HDCP status cannot be determined

Local: 1-408-962-0515 Command Feedback Description Statusx1 x7AVx1 Shows what input is connected to selected output Status x1AVx1,x2AVx2, x3AVx4, .... Displays which inputs are currently connected to which outputs SaveY (ex. Save2) SaveY (ex. Save2) Saves settings for future use, preset options 0 to 4 RecallY (ex. Recall2) RecallY (ex. Recall2) Recalls saved settings for the number you selected ClearY (ex. Clear2) ClearY (ex. Clear2) Erases the save for the number you selected Mreset Mreset Sets matrix back to the default settings RS232zoneX[command] ex: RS232zone1[PWON] RS232zoneX[command] ex: RS232zone1[PWON] Send commands to devices connected to the receiver RS-232 ports. Commands are the same as the ones stated in this table. X = zone number example: Turning the power on for the device connected in zone 1 Command Feedback Description IPCFG IP Addr : x.x.x.x Netmask : x.x.x.x Gateway : x.x.x.x IP Port: x.x.x Displays IP address configuration IPTimeout XX IPTimeout XX (Ex. IPTimout120) Determines amount of seconds of inactivity before TCP/IP disconnects IPQuit IPQuit Logs out of TCP/IP IPAddUser TCP/IP username & password list: - user password - user password - user password Will display a list of users IPAddUser [X] [Y] TCP/IP user was added Add a user for TCP/IP control. X=User Y=Password Ex. IPAddUser Atlona 1234 (User=Atlona 1234=Password) Each command or feedback is terminated with a carriage return. Note: If the command fails or is incorrect the feedback should be “Command FAILED” TCP/IP Commands RS-232 & TCP/IP Commands The command codes are case sensitive, do not change capitalization, spacing, or lettering. Command Feedback Description PWON PWON Power on PWOFF PWOFF Power off PWSTA PWx Will display the power status of the matrix (ex. Power is on = PWON) Version (Firmware #) Brings up the current firmware version Lock Lock Locks the front panel of the matrix so no buttons are active Unlock Unlock Unlocks the front panel of the matrix, enabling the buttons again All# x1AVx1,x2AVx2,... Resets all inputs to corresponding outputs (in3 to out3) x1$ x1$ Turns off output channel (to turn off output 3 = x3$) x1AVx2 x1AVx2 Switch input to output (input 3 to output 2 = x3AVx2) x1AVx2,x3,x4 x1AVx2,x3,x4 Switch input to multiple outputs (input 3 = x3AVx1,x2) IRON IRON Turns on the IR receiver IROFF IROFF Turns off the IR receiver

Local: 1-408-962-0515 RS-232 Command for the Output baud rate status RS232para The RS-232 status command will provide feedback for the current parameters for each output. Example: (See example of feedback below) RS232para Current RS232 parameter: - Port 1 :BaudRate 2400bps, DataBits 0, Parity None, StopBits 1. - Port 2 :BaudRate 9600bps, DataBits 0, Parity ODD, StopBits 1. - Port 3 :BaudRate 9600bps, DataBits 0, Parity None, StopBits 1. - Port 4 :BaudRate 9600bps, DataBits 0, Parity None, StopBits 1. Note: Default for the outputs is: Baud-9600bps, Data length-8bit, Parity-None, Stop Bit-1 Note: Default for the matrix is: Baud-115200bps, Data length-8bit, Parity-None, Stop Bit-1 The ability to check baud rate status on the outputs will help to identify control compatibility for in zone RS-232 devices. Baud Rate Default baud rates of the matrix and receivers have been set for the best compatiblity with other devices (i.e. projectors). Baud rates should not be changed unless an incompatibility occurs. To change the baud rate of the matrix or the receiver (AT-PRO3HDREC) an RS-232 hyperterminal will be needed. Once the RS-232 hyperterminal is set up changing the baud rate will be done with a command line. The baud rate for the matrix is for matrix control and the output baud rate is for control of the RS-232 device in the zone being controlled. Note: Baud rate options 2400, 4800, 9600, 19200, 38400, 57600, or 115200 Command for Matrix baud rate CSpara[baudrate,data-length,parity,stop-bit] (data, parity, and stop for matrix must be 8,0,1) For example if you wish to change the baud rate to 38400 the command would look like this: CSpara[38400,8,0,1] IPDelUser [X] TCP/IP user was deleted Delete a user from TCP/IP X=User (Ex. IPDelUser Atlona) IPDHCP sta IPDHCP sta Ex. IPDHCP on Displays the status of DHCP IPDHCP on IPDHCP on Turns DHCP on IPDHCP off IPDHCP off Turns DHCP off IPStatic [X] [Y] [Z] IPStatic address netmask gateway Sets a static IP address Ex. IPStatic 192.168.1.1 255.255.255.0 192.168.1.200 IPPort IPPort Y Set the TCP/IP port (ex. IPPort 230) IPLogin sta IPLogin sta Ex. IPLogin on Displays IPLogin status IPLogin on IPLogin on Enables IPLogin IPLogin off IPLogin off Disables IPLogin Broadcast sta Broadcast sta Displays broadcast mode status Broadcast on Broadcast on Enables broadcast mode Broadcast off Broadcast off Disables broadcast mode TCP/IP Commands Cont.

Local: 1-408-962-0515 Remote Control Output selection. Numbers correspond with the category cable outputs (1-6) on the matrix. Input selection. Numbers correspond with the HDMI inputs (1-6) on the matrix. Arrow buttons are not functional for this product. Command for Output (receiver) baud rate RS232paraX[baudrate,data-length,parity,stop-bit] X represents the zone# (output#), the data length must be 7 or 8, partity bit will be 0 for none, 1 for odd, 2 for even, and the stop-bit must be 1 or 2. For example if you wish to change the baud rate to 19200, data length 8, ODD parity, and 1 stop-bit on the receiver in zone 3 to 19200 the command would look like this: RS232para3[19200,8,1,1]

Local: 1-408-962-0515 Updating and Resetting Updating firmware Resetting to factory settings Atlona has made field firmware updating easy. Simply download firmware from Atlona.com and upload the file to the matrix. NOTE: Only use a Windows computer to update the matrix. Use of an Apple computer to update will cause the matrix to be unusable until the update is redone with a Windows computer. Atlona understands that settings can be troublesome and at times its just easier to set things back to factory settings. To make things easier a simple one step reset was created. To reset the matrix, hold down the buttons 1 and 4 while powering on. If successfull the matrix will be back to factory settings when it turns on. Needs: • Verify the current firmware version • RS-232 9 Pin to 9 Pin cable. • PC (not compatible with MAC) • OS that supports USB mass storage devices • USB A to USB B cable Preparing the Matrix: • Unplug the power cable. • Hold the Cancel button while plugging the power back in. • Connect the USB B to USB A cable into the Matrix and the Computer. Updating the Matrix: The computer should auto detect the connection, if it does not, open the USB device from “my computer”. • Click open in a new folder. (if auto run detects connection) • Delete the file in the folder. (there should be only one file, if more, delete all files) • Copy and Paste the new firmware file into the USB folder. • Unhook the Matrix from the computer. • Unplug the power cable from the AT-PRO3HD66M • Plug the power back in and start the matrix normally. Your update should be complete If you wish to verify the new firmware, use the RS-232 command “Version”. To view the current firmware use RS-232 command “Version”. AT-PRO3HD66M Select Input Number home screen ---> ---> ---> ---> Power LED should turn RED to indicate the Matrix is in standby mode/off. Unplugging then plugging back in can also set the Matrix into standby. --- --- --- --- Reset to Factory Settings Simultaneously

Local: 1-408-962-0515 Specifications Bandwidth 6.75Gbps Ports Video input Video output Audio output IR input IR output Control: RS-232 Control: TCP/IP Firmware update 6 x HDMI 6 x RJ45, 2 x HDMI 4 x S/PDIF 7 x 3.5mm 7 x 3.5 mm 1 x 9pin (RS-232) 1 x RJ45 1 x USB B Power Consumption 90W Audio Passes up to Dolby TrueHD or DTS-HD Master Audio Distance 230ft (70m) @ 1080p over CAT6a/7 197ft (60m) @ 1080p over CAT5e/6 Resolution Video: up to 1080p@60Hz VESA: up to 1920x1200 Dimensions 3.45 x 17.24 x 10.98 (inch) 87.5 x 438 x 279 (mm) Weight 9.55 lbs 4.32 kg Rack Size 2 U, 19 in. standard electronics rack Temperature Operating 32°F to 104°F 0°C to 40°C Storage -4°F to 140°F -20°C to 60°C Certifications CE, FCC, RoHS, cULus for power supplies

Local: 1-408-962-0515 Safety Information Safeguards Precautions FCC regulations state that any unauthorized changes or modifications to this equipment, not expressly approved by the manufacturer, could void the user’s authority to operate this equipment. Operate this product using only the included external power supply. Use of other power supplies could impair performance, damage the product, or cause fires. In the event of an electrostatic discharge this device may automatically turn off. If this occurs, unplug the device and plug it back in. Protect and route power cords so they will not be stepped on or pinched by anything placed on or against them. Be especially careful of plug-ins or cord exit points from this product. Avoid excessive humidity, sudden temperature changes or temperature extremes. Keep this product away from wet locations such as bathtubs, sinks, laundries, wet basements, fish tanks, and swimming pools. Use only accessories recommended by Atlona to avoid fire, shock, or other hazards. Unplug the product before cleaning. Use a damp cloth for cleaning and not cleaning fluid or aerosols. Such products could enter the unit and cause damage, fire, or electric shock. Some substances may also mar the finish of the product. Never open, remove unit panels, or make any adjustments not described in this manual. Attempting to do so could expose you to dangerous electrical shock or other hazards. It may also cause damage to your AT-PRO3HD66M. Opening the product will void the warranty. Do not attempt to service the unit. Disconnect the product and contact your authorized Atlona reseller or contact Atlona directly. To reduce the risk of electric shock, do not expose this product to rain or moisture If the wall plug does not fit into your local power socket, hire an electrician to replace your obsolete socket. Do not modify the wall plug. Doing so will void the warranty and safety features. This equipment should be installed near the socket outlet and the device should be easily accessible in the case it requires disconnection.

Local: 1-408-962-0515 Limited Warranty Atlona Technologies warrants that (a) its products (AT-PRO3HD66M) will perform substantially in accordance with the accompanying written materials for a period of 3 years from the date of receipt and (b) that the product will be free from defects in materials and workmanship under normal use and service for a period of 3 years. In the event applicable law imposes any implied warranties, the implied warranty period is limited to 3 years from the date of receipt. Some jurisdictions do not allow such limitations on duration of an implied warranty, so the above limitation may not apply to customers that fall within those areas. Customer Remedies Atlona Technologies’ and its suppliers’ entire liability and Customer’s exclusive remedy shall be, at Atlona Technologies’ decision, either return of the price paid for the product, repair, or replacement of the product that does not meet this Limited Warranty and which is returned to Atlona Technologies with a copy of the Customer’s receipt. This Limited Warranty is void if failure of the product has resulted from accident, abuse, misapplication, or natural occurrence. In example but not limited to: power surges (electrical storms, local power outage), dropping the product (or items on the product), contact with fluids, and physical misconduct (i.e. kicking or punching). Any replacement product will be warranted for the remainder of the original warranty period. No other warranties To the maximum extent permitted by applicable law, Atlona Technologies and its suppliers disclaim all other warranties, either expressed or implied, including, but not limited to, implied warranties of merchantability and fitness for a particular purpose, with regard to the product and any related written materials. This Limited Warranty gives customer specific legal rights. Customers may have other rights depending on the jurisdiction. No liability for damages To the maximum extent permitted by applicable law, in no event shall Atlona Technologies or its suppliers be liable for any damages arising out of the use of or inability to use this product, even if Atlona Technologies has been advised of the possibility of such damages. Such damages include but are not limited to: special, incidental, consequential, or indirect damages for personal injury, loss of business profits, business interruption, loss of business information, or any other pecuniary loss. Atlona Technologies’ and its suppliers’ entire liability under any provision of this agreement shall be limited to the amount actually paid by you for the product. Some Jurisdictions do not allow the exclusion or limitation of liability for consequential or incidental damage. The above limitations may not apply to you in such jurisdictional cases. Warranty

Local: 1-408-962-0515 Atlona Product Registration Thank you for purchasing this Atlona product. - We hope you enjoy it and will take an extra few moments to register your new purchase. Registration creates an ownership record if your product is lost or stolen and helps ensure you’ll receive notification of performance issues and firmware updates. At Atlona, we respect and protect your privacy, assuring you that your registration information is completely secure. Atlona product registration is completely voluntary and failure to register will not diminish your limited warranty rights. To register go to: http://www.atlona.com/registration