progressive automations TY-01 Operation & User’s Manual

Specifications Tools Required Hardware Assembly Instructions Page 3 Contents Page 4-6

2 Control box Wireless remote 28.98 Retracted: 31.89” extended: 70.89” 27. 17 11.81 16.69 7.09 2.95 2.95 1.18 1.97 1.26 32 5.67 5.55 7.09 0.39 m6 Specifications Dynamic Load Retracted Length Speed at Full Load: Output Voltage: Weight: Overload Protection: Duty Cycle: IP Grade: Operational Temperature: Certification: Tube Material: 120V~ 60Hz, 86W Yes 10% (2 minutes on, 18 minutes off) IP20 CE and UL Powder painted steel tube -5ºC~+20C (23ºF~104ºF) 130 lbs 0.98"/sec 31.89" Input Voltage: Stroke Length: 39" 24VDC 2A 42 lbs Static Load 150 lbs Color: Black Control Options: RF remote/ Wired remote

8 Washers M6 3 Tools Required allen Wrenches M6 M8 philips head screw Hardware 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 1 1 8 8 8 2 1 4 1 4 4 2 1 1 1 mounting base column Washers m6 spring washers m6 Hex Bolts m6x14 screws m5x50 tV mounting bracket nuts m8 mounting bracket screws m6x16 screws m8X16 connection cable and power cable Remote Handset control box no. type Qty

Bases to the bottom of the column. tighten the 4 screws (2 per side). 1 use 4 Hex Bolts m6x16, each with spring washer and Washer, to attach mounting bracket to the top of the column. tighten the 4 screws. 2 use 4 screws m6x16, to assemble the tV mounting bracket as following. 3 use 4 Hex Bolts m8x16, each with spring washer and Washer, to attach tV mounting bracket on to the mounting bracket. tighten the 4 screws. 4

the backside of the tV set with 4 screws included with tV set. and then hang the tV set onto the tV mounting bracket as following. use 2 m5x50 screws to tighten on the bottom. 5 connect the Wires as per the diagram below. now your tV lift is ready for use. (press the buttons of the handset and column will move up/down) 6 operating: You can use the remote or handset operate the tV lift. (1) Remote: Press S1+S3, TV lift move up, press S2+S3, TV lift move down. (2) Handset: Press UP button, TV lift move up, press DOWN button, TV lift move down. (3) During the movement, you can press any button on remote or handset (not the RESET button on handset), TV lift stop at once. 7 s1 s3 s2 Setting the UPPER and LOWER limits: • Press and hold the UP button (red) on the control box while simultaneously pressing the UP button on the handset. Raise the TV lift to the desired height. Release both UP buttons to set the UPPER limit. • Press and hold the DOWN button (black) on the control box while simultaneously pressing the DOWN button on the handset. Lower the TV lift to the desired height. Release both DOWN buttons to set the LOWER limit. Both UPPER and LOWER limits have now been set.

the TOP position higher than the original TOP position and BOTTOM position lower than the original BOTTOM position. To reset the UPPER and LOWER limits, please follow step 8. Some other information: (1) Frequency study: If you lose the wireless remote and buy a new remote from your local distributor, the frequency of the new remote may not match with your control box. You should STUDY the frequency between the remote and control box with the following procedure: 1. Press any button S1 (or S2 and S3) and the STUDY button on the handset at the same time and hold them. Several seconds later, the LED on handset will blink and you finish the frequency study. You can now use the new remote to operate this TV lift. 2. Time protection: In order to prevent from “playing” with the TV lift, there is a time limit protection implemented. You can only operate the TV lift for 3-minutes within a 20 minute time period. If the operation time exceeds 3 minutes, the system will stop moving and the LED on the control box will blink. You should wait for 20 minutes or remove power from the control box. Afterwards you can operate the TV lift again. 3. RESET the system: If a problem occurs when operating the system, for example, a cable connection problem or the TV lift won't move when you press the UP/DOWN buttons, you should try to RESET the system by the following procedure: warning: the tv lift will move to the zero position when reset. Be sure there is no obstruction under the tv set. Disconnect and reconnect the cables. turn off the power of the control box and turn on the power again. Be sure the green leD on the control box is light on. Press the Reset button on handset and hold it. after 5 seconds, tV lift will move down slowly and then to the zero position and then move up 7 mm and stop. The Reset procedure is complete. During the Reset procedure, you should hold the Reset button and the leD light on the handset will blink during the Reset procedure. the leD on the handset will turn off after finishing the Reset. You can operate the system now. 10 10 Cont.