Von Duprin 6212WF Installation Instructions
Text of the manual
6212WF/6212WFDS Electric Strike
®
Figure 1
DC input is
nonpolarized.
NOTE
!
J1
J2
P2
Switches shown with tripper
depressed, strike lip closed and locked
(switches and tripper on 6212WFDS only)
Use crimp connectors to
splice field wiring to P2
leads; insulate unused leads
P1
P1 J1A
P1A
SO-12 or SO-24
12 VDC
or
24 VDC
12 VAC SO-12 12 VDC
or
24 VAC SO-24 24 VDC
{
{
J2
Fail safe (FS)
J2
Fail secure (FSE)
S1
S2
1
2
3
4
5
6
S1
S2
1
2
3
4
5
6
Wiring
for DC
supply
Wiring
for AC
supply
4.
Test strike: Apply solenoid power. Fail secure (FSE) lip unlocks.
Fail safe (FS) lip locks. Figure 1 shows status of switches.
5.
Install strike with two #12-24 screws. Make sure clearance
between latch bolt and strike lip is 1/32” (Figure 2). If not,
uninstall strike, adjust (Figure 3), and reinstall.
6. If latch bolt does not extend far enough to actuate tripper,
install extension (Figure 4). (Tripper on 6212WFDS only.)
7. Test door: With strike unlocked, door opens with latch bolt
extended. When door closes, latch bolt rides over strike lip.
931222_00(6) Copyright © 2004 Ingersoll-Rand. All rights reserved.
Solenoid
89/336/EEC
Standard: 5 A, 30 VDC
Gold: 0.25 A, 30 VDC
SWITCH RATINGS
}
P2
Red (C)
Blue
Yellow
White (C)
Gray
Violet }
S1
(monitors
tripper)
S2
(monitors
strike lip)
Use crimp
connectors to
splice field wiring
to P1 leads
Tripper
Figure 4
Extension
Figure 2
Top view;
faceplate not
shown for clarity
1/32”
Latch bolt
Strike lip
Yellow solenoid wires = 12 VDC, 0.57 A
Black solenoid wires = 24 VDC, 0.29 A
(also shown on strike label)
SOLENOID POWER REQUIREMENTS
Figure 3
To adjust strike,
loosen screws A, B,
and C and move
backbox sideways
as necessary
A
B
C
Notes:
Deadbolt will not function with this strike.
Check with factory for retrofit applications.
1. For lock or device preparation, see their directions.
2. Prepare frame for strike (see other side).
3. Wire strike (Figure 1). (Switches on 6212WFDS only.)
Single Door Wood Frame Mortise or Cylindrical Application
931222-00
Strike Dimensions and Required Clearances
Door Preparation for Strike
931222_00(6)
Pilot drill for
#12 wood screws
LHR shown
RHR opposite
1-7/16” minimum
clearance
6” long lead wires; 1/2” dia.
minimum wiring access
5/8”
1-11/16”
Minimum
clearance
2-3/8” minimum
clearance
3-3/8”
6-3/8”
1-1/4”
1-1/8”
1/8”
C strike
L
L
C lock and strike
L
5-5/8”
C strike
3/4”
3-3/8”
1-1/4”
5/8”
1-15/32”
1” dia. minimum
clearance
6-3/8”
3-3/16”
2-13/16”
5-5/8”
1-13/32”
3-9/16”
3-11/16”
1-15/32”
2-3/8” minimum
clearance
