TriMark e-ASK Instruction Manual

Discrete e Discrete e--PAD PAD Instruction Manual (UM10 ~ 21067-01)

Introduction ............................................................................... 1 e-PAD Operation and Features ................................................ 1 Locking Doors With Keypad ................................................... 2 Secure Operations .................................................................. 2 Dome Light Activation ............................................................. 2 Protective Deactivating Security Feature ............................... 2 Buzzer Operation .................................................................... 3 Keypad Backlight Operation ................................................... 3 Teaching Keypad New Authority / Access Codes ................. 3 Changing Authority Code ....................................................... 3 Change / Add Access Codes ................................................. 4 Appendix A: Mounting Information .......................................... I Appendix B: Wiring Information .............................................. II Wire Identification ................................................................... II Wiring Diagram ....................................................................... III

installation and use of TriMark’s discrete e-PAD system. Note: Some features discussed in this manual may not be available on your system. e-PAD keypad 1 Note: Horizontal or vertical e-PADs are available. e-FOB Operation and Features The e-PAD is shipped with default authority and access codes. Unless the OEM or dealer has changed the default codes, the authority and access codes are as follows: Access code: Authority code: Digit 1 Digit 2 Digit 3 Digit 4 Digit 5 1 / 2 3 / 4 5 / 6 7 / 8 9 / 0 Digit 1 Digit 2 Digit 3 Digit 4 Digit 5 7 / 8 7 / 8 7 / 8 7 / 8 7 / 8

only used to assign access codes (see page 3 for information on setting authority and access codes). • If an unassigned button or no button is pressed while the system is enabled, the keypad reverts back to disabled state. • The secure keypad operations are set depending on the system configuration. Dome Light Activation The dome light is activated for 30 seconds whenever a secured operation occurs. Protective Deactivating Security Feature After repeated entering of incorrect codes (20 button presses without enabling), the keypad is deactivated for 1 minute. This helps prevent unauthorized access by entering random codes. No beep will sound with button press while the system is disabled. 2 Locking Doors With Keypad Press and hold down the (1 / 2) button for 1-2 seconds. An access code is not needed to lock the doors. Secure Operations Entering a valid 5-digit access code enables secure operations. After entering an access code, the keypad is enabled for 5 seconds and a 6th button press initiates a secure operation, such as unlocking the doors. The table below shows the default button assignments: 1 / 2 Button Unlocks entry doors 3 / 4 Button 5 / 6 Button Unlocks Bank Two (may be set to left side of vehicle) 7 / 8 Button Unlocks entry doors, Bank One and Bank Two with staggered actuation 9 / 0 Button Activates light for 5 minutes. Repeating sequence while light is on turns light off. Unlocks Bank One (may be set to right side of vehicle)

for each key press during regular use. When an authorized access code is entered, the system chirps twice to indicate readiness for a secure operation (6th button press). The system chirps twice for each button press while in Learn Mode. When a new access code is defined, the system chirps 3 times. Keypad Backlight Operation When the e-PAD is in the normal state, the backlighting is at a low level. When a button is pressed, the keypad backlight flashes bright. The keypad backlight also has a power saving mode if voltage is below 11 volts, the continuous backlighting is shutoff until the battery is fully charged. When continuous backlighting is off, the keypad still “wakes up” when a button is pressed. In this case, the backlighting is activated for only one minute. If the battery voltage is increased to 12.5V for 5 minutes, then the keypad back lighting will return to low brightness level. Teaching Keypad New Authority / Access Codes Change Authority Code The following procedure resets the default authority and access codes. It then assigns a new authority code. The authority code is only used to teach access codes. Notes: • The memory for authority and access codes is NON-VOLATILE and will not be erased if power is removed. • Changing the authority code is the only activity that requires access to the learn mode wire in the wiring harness.