TreeGreen energyEGG Manual 

The energyEGG® is a wireless appliance controller. It makes switching of appliances in a room - or around the home - simple. It automatically switches of electrical equipment after you leave the room - saving energy, time and reducing electric bills. It has 3 main functions : ROOM ON/OFF Pressing the Power Button (see Figure 1) switches ON appliances. Pressing and holding the Power Button for 2 seconds switches OFF appliances connected to the Control Adaptor(s) (see Figure 3) in a room. Auto Room OFF When a room is empty for a preset time the energyEGG® (Figure 2) automatically switches OFF connected appliances. HOME OFF Pressing and holding the Power Button for 5 seconds, while appliances are ON, switches OFF all connected appliances around a home. Please note that the maximum range of the energyEGG® may vary depending on the building it is being used in .

Power Button LED Indicator Battery Compartment Smart Motion Sensor Adjustable Timer on Base Figure 1 The energyEGG® Figure 2 Timer Dial Timer OFF Setting Dial energyEGG® Figure 4: Positioning your energyEGG® 100º 2.5m 3.5m

STEP 1 Plug the Control Adaptor into a mains socket, making sure that the wall socket is switched on. The LED on the Control STEP 2 Insert the battery into the energyEGG®. Press the Power Button to signal the Control Adaptor. The LED on the successfully linked with the energyEGG®. Test the Control Adaptor by switching it ON and OFF using the energyEGG® Power Button. STEP 3 When the energyEGG® it detects movement. Place your energyEGG® (See Figure 4) up to 2.5m from where you usually sit, around 1m from the Figure 1) facing you. Test the energyEGG® position by waving your hand and checking that the energyEGG® energyEGG® works best when it is not placed in direct sunlight. STEP 4 Plug in an appliance or power strip to the Control Adaptor. Switch OFF appliances by pressing and holding the button for 2 seconds - the energyEGG® will beep twice to indicate that you can release the button. The 2 second button delay helps prevent accidental switch OFF. STEP 5 To connect an additional Control Adaptor to the energyEGG®, simply repeat these steps. Experiment with the best position for the energyEGG® to signal all Control Adaptors. Note : To connect an extra energyEGG® to a control adaptor, press and hold the button on the Control Adaptor until the light Now press the button on the energyEGG® to connect it.

STEP 6 Set the timer on the base of the energyEGG®. Remember to give yourself enough time to leave the room, make a cup of tea, and return. This will ensure your appliances are not inconveniently switched OFF. If you do not want the energyEGG® to automatically switch of your appliances set the Timer Dial to the ‘TIMER OFF’ setting (See Figure 2). TreeGreen recommends using a power strip instead of severalControl Adaptors when connecting multiple appliances Note : If you connect your computer to the energyEGG® ensure that the computer is set to go into sleep mode 5 minutes before the energyEGG® timer setting. So if your computer is set to go into sleep mode after 10mins, set the energyEGG® dial to 15mins. TreeGreen takes no responsibility for wrong setup or lost data. TreeGreen recommends that you regularly save and back up your data. ADDITIONAL FEATURES Auto Your energyEGG® automatically turns OFF appliances OFF when you forget. It detects when a room is empty and sends a switch of signal to the Control Adaptor(s) after a preset time (between 5 and 30 mins). Turn the dial to your preferred time delay using the intervals on the base as a reference.

AUTO OFF The energyEGG® will alert you 1 minute before it switches Alert anything OFF by beeping and fashing the green light. This gives you an opportunity to prevent the AUTO OFF by moving or coming back into the room. Feedback When the energyEGG® automatically switches appliances OFF it lets you know by beeping the next time you enter the room and then fashing the LED green for 1 minute. HOME OFF Switch of Control Adaptors in diferent rooms using a single energyEGG® - by pressing the energyEGG® button for 5s. To set up the HOME OFF function frst ensure that the energyEGG® is in ON mode (fashes when it detects movement). Then put each control adaptor you want to respond to HOME OFF into ‘learn mode’. Now press and hold the Power button on the energyEGG® for 5 seconds and release. Timer OFF If you wish to deactivate the Auto Room OFF of the energyEGG® and have manual button control only, simply rotate the dial to the OFF’ setting (see Figure 2). Battery If your energyEGG® begins to run out of battery power, it Replacement will beep intermittently for around 5 minutes when Alert you switch it on. If it starts to beep during operation and a detected movement does not stop the beeping then you need to replace the battery. Reset Control To disconnect a Control Adaptor from all energyEGGs®, Adaptor press and hold the button on the Adaptor until it fashes slowly, then fashes quickly.

Solution: Should the energyEGG® go into power of mode while you are in the room, reposition the energyEGG® and ensure there are no obstructions to the feld of view. If you use several energyEGGs®, this may be a result of setting up the HOME OFF function incorrectly - if so, repeat the HOME OFF set up instructions. Problem: ‘My energyEGG® does not switch of appliances’ Solution: Should the energyEGG® fail to switch on/of appliances: repeat SET UP INSTRUCTIONS. Should the problem persist, replace the battery. Also Check that the range is within 20m. Problem: ‘My energyEGG® switches my appliances of when I leave the room to make a cup of tea or go to the bathroom’ Solution: Should the energyEGG® switch of appliances when a room is vacated for a short period then increase the delay setting on the timer dial. Problem: ‘I have energyEGGs® in several rooms switching of the same Control Adaptor when I use the ROOM ON/OFF function.’ Solution: Reset the Control Adaptor. To do this press and hold the button on the Control Adaptor - continue holding the button until the LED on the Control Adaptor fashes slowly and then begins to fash quickly. This disconnects the Control Adaptor and puts it into Learn Mode. For Solutions to any other Problems, please contact [email protected]

. Do not allow children or people unfamiliar with these instructions to use your energyEGG®. . Place your energyEGG® away from sources of heat, liquid and out of the reach of children. The following safety recommendations should be followed when using energyEGG®: . The energyEGG® should not be used to control appliances that need to be left on at all times. . To protect against fre, electric shock and personal injury do not immerse the energyEGG® unit or Control Adaptor in water or any other liquid. . Do not use your energyEGG® outdoors or in the bathroom. . Do not connect your energyEGG® to any appliance with a damaged lead or mains plug, or to damaged or faulty appliances. . Do not disassemble or modify your energyEGG® unit. . Using the energyEGG® to control a computer or hard drive may result in loss of data. Care and maintenance . Disconnect components from the power supply before cleaning. . To clean, use a dry cloth - do not use solvent, abrasive cleaners or water. . Do not immerse the energyEGG® or Control Adaptor in water or any other liquid.

Power Rating (Socket) 13A, 230V Socket Power Consumption (in OFF mode) <0.25W Maximum Load (Socket) 3000W Transmission Frequency 433.92MHz Operating Temperature 1ºC - 40ºC Dimensions EGG : 109 x 65 x 56mm Control Adaptor : 109 x 55 x 70mm Weight EGG: 0.101kg, Control Adaptor: 0.138kg Battery Type PP3 (6F22) Carbon Zinc 9V Battery Disposal This product should be handed over to a designated collection point, such as an authorised collection site for recycling waste electrical and electronic equipment. For more information about where you can dispose of waste electrical and electronic equipment, please consult your local council, waste authority or approved WEEE scheme. Disposal Your energyEGG®® comes with a 12 month manufacturer's warranty as standard. In the event of a physical defect due to material or workmanship, please contact us, stating where and when you purchased the device. If you discover a defect covered by this warranty we will repair or replace the product at our discretion using new or refurbished components. Technical Specifcations Warranty

correct use of the device. It is limited to defects in materials or workmanship and does not cover damage caused by abuse, misuse, unauthorised modifcation, power surge damage or extreme heat or cold or corrosive environments. TreeGreen is not accountable for loss of software, frmware, data or information resulting from the use of the energyEGG®. The warranty also does not cover the normal wear and tear on covers, cases, housings, connectors and accessories. The warranty does not apply to any product with missing, altered or defaced serial numbers. Limits of Liability If this product fails or does not perform as warranted,please contact TreeGreen. TreeGreen will not be liable to you or anyone else for any damages that result from the failure of this product. These damages include, but are not limited to, the following: lost profts, lost savings, lost data, damage to other equipment and incidental or consequent damages arising from the use or inability to use this product. In no event will TreeGreen be liable for any amount in excess of your purchase price, not to exceed the current list price of the product. Nothing in this warranty limits liability for death or personal injury caused by negligence or fraud. TreeGreen specifcally disclaims any other warranties, expressed or implied.

Simply register your new energyEGG® at www.treegreen.net and TreeGreen will extend your standard 12 month warranty to a total of 3 years from the original date of purchase. To obtain service under the 3 year warranty contact TreeGreen at [email protected]. Once TreeGreen verifes that you have a valid hardware problem, you will be given guidance on returning the defective unit. You must return the defective unit to TreeGreen in order to receive full service. Manufacturer Details Your energyEGG® was developed and manufactured by TreeGreen. If you have any questions which have not been answered in this user manual, please contact us by calling 08458675838 or emailing [email protected] . TreeGreen Ltd. is a limited company registered in Scotland.

energyEGG®, or to purchase additional EGGs® or Control Adaptors, visit www.treegreen.net ENERGY EGG, EnergyEgg and Energy-EGG have been registered as a series of four marks under No.2504839 as of 16th December 2008.