WAGNER GM 5000EAC F Operating Manual

10.3.2 ACR 5000 ROUND JET NOZZLE CAP SPARE PARTS LIST ACR 5000 round jet nozzle cap spare parts list Item K Quantity Part No. Description 1 1 2309883 ACR 5000 round jet nozzle cap 2 1 2307220 Nozzle nut 3 ◆ 1 2315310 O-ring 4 ◆ 1 132351 Nozzle screw connection holder 5 1 2307219 Nozzle body 6 ◆ 1 2319526 Round electrode set 9 ◆ 1 132516 Nozzle screwed connection compl. 10 ◆ 1 2307216 Sealing nipple 11 ◆ 1 2311217 O-ring 12 1 128901 Nozzle spanner compl. ◆ = Wear part ...

5.4 WORKING 5.4.1 FILLING WITH WORKING MATERIAL 1. Provide an empty container for return (18). See image B_03158. 2. Place suction hose (7) in the container with working material (19). Note: If the pump is equipped with a rigid suction system, it should only be diped in into the working material in maximum to the middle of the inlet housing! 3. Adjust approx. 0.05 MPa; 0.5 bar; 7.25 psi on the pressure ...

2.2.4 CLEANING 2.2.5 HANDLING HAZARDOUS LIQUIDS, VARNISHES AND PAINTS ���When preparing or working with paint and when cleaning the unit, follow the working instructions of the manufacturer of the paints, solvents and cleaning agents being used. ���Take the specified protective measures, in particular wear safety goggles, protective clothing and gloves, as well as hand protection cream if necessary. ���Use a mask or breathing apparatus if necessary. ���For sufficient health and environmental safety ...

4.4.2 FUNCTIONS OF THE SPRAY GUN Distance Description 1 AirCoat air opens. 2 AirCoat air opened and electrostatic (HV) activated. -> Display (2) for „spray current“ on the spray gun ●❍❍❍❍ to ●●●●● activated. 3 AirCoat air opened and electrostatic (HV) activated and material valve opened. 4 Max way of trigger. • An increase in the tension needed to pull the trigger back will be felt at the position where the material valve opens. • For sprayi ...

5.3 START-UP 5.3.1 GENERAL RULES FOR MAKING ADJUSTMENTS TO THE SPRAY GUN ➞ Observe safety instructions in Chapter 2. 5.3.2 PREPARATION FOR STARTING UP The following points should be noted before commissioning: ➞ For earthing see paragraph 5.1.5; make sure that all other conductive parts within the work area are earthed. ➞ Connect the material hose to spray gun and material pump.. ➞ Check that all material-conveying connections are correctly connected. ➞ Connect air hose to spray gun and to oil-free, dry air, appr ...

4.1 FIELDS OF APPLICATION, USING IN ACCORDANCE WITH THE INSTRUCTIONS The electrostatic spray gun can only be used with the VM 5000 or VM 500 control units. 4 DESCRIPTION 4.1.1 PROCESSABLE MATERIALS ➞ With the GM 5000EAC gun, paints can be applied which contain solvent of explosion class II A. ➞ The spray gun basic version is suitable for processing of sprayed substances with an electrical resistance of > 150 k (according to the WAGNER scale). Equipped with a special material hose for low impedance sprayed substanc ...

4.1 FIELDS OF APPLICATION, USING IN ACCORDANCE WITH THE INSTRUCTIONS The electrostatic spray gun can only be used with the VM 5000 or VM 500 control units. 4 DESCRIPTION 4.1.1 PROCESSABLE MATERIALS ➞ With the GM 5000EAC gun, paints can be applied which contain solvent of explosion class II A. ➞ The spray gun basic version is suitable for processing of sprayed substances with an electrical resistance of > 150 k (according to the WAGNER scale). Equipped with a special material hose for low impedance sprayed substanc ...