GE PSA2201RSS Installation Instructions Manual

CÓMO PREPARAR LA PARED POSTERIOR PARA EL ESCAPE POSTERIOR EXTERIOR B1 PERSPECTIVA GENERAL DE LA INSTALACIÓN B1. Prepare la pared posterior B2. Pegue el plato de montaje a la pared B3. Prepare el gabinete superior B4. Ajuste el calefactor B5. Monte el horno Instrucciones de instalación B 39 CÓMO ADHERIR EL PLATO DE MONTAJE A LA PARED B2 Pegue el plato a la pared usando los tornillos basculantes. Por lo menos un tornillo de madera debe ser usado para pegar el plato al poste de viga de la pared. Remueva las mariposas de los tornillos. Inserte los ...

el fondo del gabinete. 1 CÓMO MONTAR EL HORNO A4 ENSAMBLAJE E INSTALACIÓN DEL ADAPTADOR A3 USE LA PLANTILLA DEL GABINETE SUPERIOR PARA LA PREPARACIÓN DEL GABINETE SUPERIOR Deberá perforar agujeros para los tornillos de apoyo superiores, un agujero suficientemente grande para que el cable eléctrico quepa, y un recorte lo suficientemente grande como para que el adaptador de escape pueda ser introducido. A2 PARA OBTENER UNA INSTALACIÓN MÁS FÁCIL Y EN POS DE LA SEGURIDAD PERSONAL, SE RECOMIENDA QUE DOS PERSONAS INSTALEN ESTE HORNO. IMPORTANTE: No agarre ...

42 Instrucciones de instalación 3 2 Gire el frente del horno contra el fondo del gabinete. 1 CÓMO MONTAR EL HORNO B5 PARA UNA INSTALACIÓN MÁS FÁCIL Y EN POS DE LA SEGURIDAD PERSONAL, SE RECOMIENDA QUE DOS PERSONAS INSTALEN ESTE HORNO. IMPORTANTE: No agarre ni use la manija de la puerta durante la instalación. NOTA: Si su gabinete es de metal, use la arandela de nilón alrededor del cable eléctrico para evitar que el mismo sea cortado. NOTA: Recomendamos el uso de bloques de relleno si el frente del gabinete cuelga por debajo del estante d ...

# 1 and #2 Phillips screwdriver Pencil Ruler or tape measure and straight edge Carpenter square (optional) Tin snips (for cutting damper, if required) Electric drill with 3⁄16″, 7⁄16″, 1⁄2″ and 5⁄8″ drill bits Hammer (optional) Stud finder or Filler blocks or scrap wood pieces, if needed for top cabinet spacing (used on recessed bottom cabinet installations only) Gloves Saw (saber, hole or keyhole) Level Duct and masking tape MOUNTING SPACE NOTES: • The space between the cabinets must be 30″ wide and free of obstructions. • If the space between the c ...

FOR PREPARATION OF TOP CABINET C2 19 RECIRCULATING (Non-Vented Ductless) INSTALLATION OVERVIEW C1. Attach Mounting Plate to Wall C2. Prepare Top Cabinet C3. Adjust Blower C4. Mount the Oven C5. Install Charcoal Filter (not supplied) • Read the instructions on the TOP CABINET TEMPLATE. • Tape it underneath the top cabinet. • Drill the holes, following the instructions on the TOP CABINET TEMPLATE. CAUTION: Wear safety goggles when drilling holes in the cabinet bottom. Installation Instructions You need to drill holes for the top support screws and a hole large enou ...

PREPARING THE REAR WALL FOR OUTSIDE BACK EXHAUST B1 INSTALLATION OVERVIEW B1. Prepare Rear Wall B2. Attach Mounting Plate to Wall B3. Prepare Top Cabinet B4. Adjust Blower B5. Mount the Oven Installation Instructions B 15 ATTACH THE MOUNTING PLATE TO THE WALL B2 Attach the plate to the wall using toggle bolts. At least one wood screw must be used to attach the plate to a wall stud. Remove the toggle wings from the bolts. Insert the bolts into the mounting plate through the holes designated to go into drywall and reattach the toggle wings to 3⁄ 4″ onto ...

on each knockout panel and remove the metal knockouts for rear airflow. Locate the two “knockout” plates, on the rear oven panel, near the top of the oven. Using tin snips, carefully cut the web area from the two holes side-by-side (that secure the knockouts to the oven). Cut all four webs on both rear knockouts; this will allow the ventilation fan airflow to exhaust out the rear of the oven. CAUTION: Be sure to trim the sharp edges from the openings after removing the knockout plates. AFTER: Fan Blade Openings Facing Back 7 Place the blower unit back into the opening. 9 In ...

the toggle wings into the holes in the wall to mount the plate. NOTE: Before tightening toggle bolts and wood screw, make sure the tabs on the mounting plate touch the bottom of the cabinet when pushed flush against the wall and that the plate is properly centered under the cabinet. CAUTION: Be careful to avoid pinching fingers between the back of the mounting plate and the wall. Tighten all bolts. Pull the plate away from the wall to help tighten the bolts. 3 A 4 ATTACH THE MOUNTING PLATE TO THE WALL A1 12 OUTSIDE TOP EXHAUST (Vertical Duct ...