Visolux VB34 Instruction Manual

Terms of Delivery for Products and Services of the Electrical Industry, published by the Central Association of the Electrical Industry (Zentralverband Elektrotechnik und Elektroindus- trie (ZVEI) e.V.) in its most recent version as well as the supplementary clause: "Expanded reservation of proprietorship" We at Pepperl+Fuchs/VISOLUX recognize a duty to make a contribution to the future. For this reason, this printed matter is produced on paper bleached without the use of chlorine.

Table of contents and general information Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany (06 21) 7 76-0 • USA (330) 4 25 35 55 • Singapore 7 79 90 91 • Internet http://www.pepperl-fuchs.com Date of issue 06/13/2005 1 1 REFERENCE INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 1.1 ADDITIONAL DOCUMENTATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.2 Maintenance, support and warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.2.1 Maintenance and support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2 Safety regulations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 2.1 Electrical safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.2 Laser safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.2.1 Standard regulations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.3 Voltage supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3 Device views . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 4 Installation overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 4.1 Point-to-point installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 4.2 Lonworks master/slave installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 5 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 5.1 Product description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 5.2 Available models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 5.3 Displays. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 5.4 Oscillating mirror models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 5.5 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 6 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 6.1 Contents of the package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 6.2 Mechanical installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 6.2.1 Installation of the reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 6.2.2 Installation of the reader with accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 6.3 Electrical connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 6.3.1 Primary/secondary interface and I/O connections . . . . . . . . . . . . . . . . . . . . . . . . 23 6.3.2 Lonworks connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 6.3.3 Ethernet connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 6.3.4 DeviceNet connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 6.3.5 Profibus connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 6.3.6 Voltage supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 6.4 Operator interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 6.5 Adjusting the reader. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 6.6 Typical installations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 6.6.1 Standard installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 6.6.2 Installation with an angle of rotation of 45°. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 6.7 Typical hardware configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 6.7.1 Point-to-point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 6.7.2 Loops . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 6.7.3 RS232 master/slave . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 6.7.4 Multiplexer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 6.7.5 Local Lonworks network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 6.7.6 Fieldbus network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 6.8 FLASH™ dynamic focusing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 6.8.1 Fixed adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Table of contents and general information Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany (06 21) 7 76-0 • USA (330) 4 25 35 55 • Singapore 7 79 90 91 • Internet http://www.pepperl-fuchs.com Date of issue 06/13/2005 2 6.8.2 Continuous adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 6.8.3 Trigger operating mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 6.8.4 D-Flash™ operating mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 6.9 Key field and display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 6.9.1 Internal Net . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 6.9.2 Test mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 7 Software configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 7.1 Software installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 7.2 Hints on quick configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 7.2.1 Assistant for quickly setting up the reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 7.2.2 Network Assistant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 7.3 Enhanced configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 7.4 Basic settings for parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 8 Optical properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63 8.1 ACR technology (ACR™ 3 reconstruction) . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 8.1.1 Tilt angle for the ACR reconstruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 8.2 PackTrack™. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 8.2.1 PackTrack™ calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 8.3 Read diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 8.3.1 VB34 standard model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 8.3.2 VB34 model with reflex mirror . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 9 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 9.1 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 10 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89 11 Technical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 12 Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 13 Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99 General information This symbol warns the user of possible danger. Failure to heed this warning can lead to personal injury or death and/or damage to equipment. This symbol warns the user of the possibility of device failure. Failure to observe this warning can lead to the complete failure of the device or any device connected to it. This symbol advises the user of important tips. Warning Attention Note

Table of contents and general information Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany (06 21) 7 76-0 • USA (330) 4 25 35 55 • Singapore 7 79 90 91 • Internet http://www.pepperl-fuchs.com Date of issue 06/13/2005 3 Declaration of conformity We, Pepperl+Fuchs GmbH, declare herewith at our sole responsibility that the Barcode Scanner VB34 and all models of this product to which this declaration pertains, are compliant with the following standards and other regulating documents EN 55022, August 1994: RADIO INTERFERENCE OF INFORMATION TECHNOLOGY EQUIPMENT (ITE), MEASURING METHODS AND LIMITS EN 50082-2, March 1995: ELECTROMAGNETIC COMPATIBILITY, GENERIC IMMUNITY STANDARD PART 2: INDUSTRIAL AREA and the guidelines of the following directive(s): 89/336 CEE AND SUBSEQUENT CHANGES MADE, 92/31 CEE; 93/68 CEE Pepperl+Fuchs GmbH, in D-68301 Mannheim, has a certified quality assurance program in accordance with ISO 9001. A corresponding declaration of conformity may be requested from the manufacturer. Note ISO9001

REFERENCE INFORMATION Date of issue 06/13/2005 4 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com 1 REFERENCE INFORMATION 1.1 ADDITIONAL DOCUMENTATION The following additional documentation on the VB34 system is available: • C-BOX100 manual • GFC-60 90° deflecting mirror • GFC-600 90° near range deflecting mirror • Documentation on Profibus communication 1.2 Maintenance, support and warranty 1.2.1 Maintenance and support Pepperl+Fuchs offers a range of services as well as technical support via its website. For further information, visit our website at www.pepperl-fuchs.com. 2 Safety regulations 2.1 Electrical safety This product meets the applicable requirements stipulated by the European standard EN 60950 on electrical safety in the version valid at the time of production. 2.2 Laser safety The following information is listed for compliance with the rules defined by the international authorities and refers to the proper use of the VB34 reader. 2.2.1 Standard regulations This reader is provided with a low-energy laser diode. Even though, according to the current state of knowledge, directly looking into the laser beam does not cause any biological damage, you should avoid doing this as for all strong light sources such as the sun. Do not direct the laser beam, neither directly nor indirectly, e.g. via mirrors, into the eyes of other people. This product meets the applicable requirements of the European standard EN 60825- 1 and the standard CDRH 21 CFR1040 in the version valid at the time of production. The reader is classified as a class 2 laser product according to EN 60825-1 and as a class II laser product according to the CDRH regulations. Before opening the device for maintenance or installation purposes, switch off the voltage supply in order to avoid exposure to dangerous laser radiation. The device is equipped with a safety device, which only switches on the laser if the motor has reached the minimum rotational speed for read mode.

Safety regulations Date of issue 06/13/2005 5 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Laser radiation is visible to the human eye and is emitted through the window in the head of the reader (Figure 3.1 and Figure 3.2). Warning labels that draw attention to the dangers of laser radiation and to the device classification are located on the head of the reader (Figure 3.1 and Figure 3.2): Figure 2.1 Laser safety labels for oscillating mirror and standard models Figure 2.2 Warning and device classification labels The name plate is located on the lower part of the reader (Figure 3.1): Figure 2.3 Name plate The laser diode used by this device is classified as a class 3B laser product according to EN 60825-1 and as a class IIIb laser product according to the CDRH regulations. As it is not possible to attach a label to the laser diode used by this device, the following label is alternatively shown here: The use of different controls or settings as well as carrying out operations other than those described here may cause exposure to dangerous, visible laser radiation. Warning

Device views Date of issue 06/13/2005 6 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Figure 2.4 Classification label of the laser diode Opening the optical components may cause radiation to be emitted with the maximum power of the laser diode (35 mW at 630~680 nm). 2.3 Voltage supply This product may be installed by qualified personnel only. All VB34 models: This device is designed for supply by a UL-listed power pack with the classification “Class 2” or by a low-voltage power pack, which connects the supply voltage directly via the 25/26-pin connector to the reader. 3 Device views Figure 3.1 Device view VB34 Laser exit window Laser safety label Name plate Warning and device classifi- cation label Service connection Connector cover Display and key pad

Device views Date of issue 06/13/2005 7 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Figure 3.2 Device view VB34 reflex mirror version Figure 3.3 Partial view of display and key pad Laser exit window Laser safety label Program key pad TXD data LED Phase on LED Power on LED LCD display

Device views Date of issue 06/13/2005 8 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Figure 3.4 View of connector cover for master/slave models Figure 3.5 View of connector cover for Ethernet models Figure 3.6 View of connector cover for DeviceNet models Figure 3.7 View of connector cover for Profibus models 25-pin Sub-D con- nector for primary/ secondary interface 9-pin Lonworks socket 9-pin Lonworks connector 26-pin Sub-D con- nector for primary/ secondary interface 9-pin Lonworks socket RJ45 connector for Ethernet interface 26-pin Sub-D con- nector for primary/ secondary interface 9-pin Lonworks socket 5-pin DeviceNet connector 26-pin Sub-D con- nector for primary/ secondary interface 9-pin Lonworks socket 9-pin Profibus socket

Installation overview Date of issue 06/13/2005 9 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com 4 Installation overview 4.1 Point-to-point installation The following overview can also be used as a check list. It lists all the steps that are required for a complete installation of the VB34 reader. 1. Read all the information in section "Safety instructions" at the beginning of this manual. 2. Install the reader using the supplied mounting material (Chapter 6.2.2). 3. Adjust the reader to the correct reading distance for your model (Chapter 6.5). 4. Wire the VB34 reader according to the following steps: a) Connect the VB34 reader to a C-BOX 100 (Chapter 5.5) using one of the accessory cables. b) Wire the C-BOX 100 with all system signals and voltages required by your application (trigger, inputs, outputs). • Layout: Point-to-point, RS232 master/slave, Lonworks or fieldbus. For fur- ther information, please refer to the sections in Chapter 6.7. • Cabling: supply, primary serial interface – RS232, RS485 half duplex, RS485 full duplex, 20 mA current loop, secondary interface, inputs, outputs etc. For further information, please refer to the sections in Chapter 6.3. 5. Configure the VB34 reader by installing and executing the configuration software from the enclosed CD-ROM. The most important steps are: • Select the codes to be read • Configure the communication parameters • Define the data format parameters • In the test mode, adjust your VB34 reader to the application as described in the configuration software. 6. Complete the configuration program and start your application. The installation is now complete. 4.2 Lonworks master/slave installation The following overview can also be used as a check list. It lists all the steps that are required for a complete installation of the VB34 reader. 1. Perform steps 1 to 3 of the point-to-point installation. 2. Wire the VB34 reader according to the following steps: a) Connect the VB34 master reader to a C-BOX 100 (Chapter 5.5) using one of the accessory cables. b) Connect the BTK-6000 termination network to the VB34 master reader as described under “Local Lonworks network” (Chapter 6.3.2). c) Install and wire all slave readers required for your system configuration (Chapter 6.7). d) Connect the BTK-6000 termination network to the last VB34 slave reader as described under “Local Lonworks network” (Chapter 6.3.2).

Installation overview Date of issue 06/13/2005 10 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Configure the VB34 slave readers using one of the following methods: a) Define the addresses of all VB34 slave readers via the key pad on the reader (Chapter 6.9). b) Configure all VB34 slave readers by installing and executing the configuration software from the enclosed CD-ROM (Chapter 7.2.2). Configure the VB34 master readers using one of the following methods: c) Configure the VB34 reader as the master using the key pad of the reader (Chapter 6.9). d) Configure the VB34 reader as the master using configuration software (Chapter 7.2.2). 3. Establish a connection to the VB34 master reader in order to configure the network layout using the configuration software. 4. Configure all VB34 slave readers using the configuration software. The most important steps are: • Select the codes to be read • Configure the communication parameters • Define the data format parameters 5. In the test mode, adjust your VB34 reader to the application as described in the configuration software™. The installation is now complete. All slave readers can also be configured externally using the configuration software and the master reader. Note

Introduction Date of issue 06/13/2005 11 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com 5 Introduction 5.1 Product description The VB34 is the high-performance laser scanner in the VISOLUX family of barcode readers for industrial applications. With its completely new hardware and software platform, it offers innovative and modular solutions regarding performance, communication and maintenance. Easy installation and operation as well as high flexibility were the most important features during the development of the VB34. Together with the Step-a-Head™ technology, for which a patent has been applied, the innovative mechanics makes it possible to turn the read head and the decoder base assembly independently of each other. Step-a-Head™ makes it possible to always install the VB34 in the ideal position by changing the position of the base assembly while the read head with the laser maintains its optimum position. This minimises the space requirements and simplifies the installation. Another innovation of the VB34 is the linear motor, which can be used to control the reading position of the scanner via software. This dynamic system with the name Flash™ is able to assume any reading position from the minimum position to the maximum position in less than 10 ms. In typical applications with a reading distance of less than 1 m, the reading position is reached in 4 ms. Thanks to a new generation of decoders with StrongARM CPU and ACR technology (ACR™ 3 reconstruction), the VB34 reads all current barcodes, even under demanding ambient conditions. The reader is also available in a version with an integrated, software-programmable oscillating mirror. Another focus in the system design was the communication capacity of the readers. As interfaces, Lonworks, Profibus, DeviceNet and Ethernet were each integrated into a separate version of the decoder base assembly. Some of the significant features of the VB34 are: • Read rate of up to 1200 read processes/second • 2 serial interfaces • Reading all current codes • Operating voltage of 15 to 30 V DC • All electrical connections pluggable • Fast Lonworks interface for master/slave configurations • Supports Profibus, DeviceNet and Ethernet • 5 operating modes for an optimum adjustment to different application requirements • Light source: laser diode with a wave length of 630 to 680 nm • IP64-protected housing (for Ethernet models not yet available) Auto-ID applications are traditionally used in the area of production. With increasing marketability, standard solutions and a dynamic competition develop. The VB3x family with the model VB33 also has its roots in production applications. The VB34 opens up new areas of application such as, for example, transport and logistics applications, in which the practical advantages of the new technologies come to the fore.

Introduction Date of issue 06/13/2005 12 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Feature Practical use Modular solution with separate head and base assembly as well as Step- A-Head™ function • Combination of the ideal head and base assemblies for a given application • Scaleable solution • Reduced tool life, as the decoder base remains functional even when the head has been removed. • Simple maintenance: All configuration parameters remain saved in the base assembly. When the read head is replaced, the scanner is configured auto- matically. • Simple installation with minimum space requirement Reading pallets or large objects over greater distances and with a large field of view • VB34 with dynamic focussing system Flash™. Reading objects on conveyor belts • VB34 implements Packtrack™ function- ality in order to increase the production of the plant by a higher system through- put. Master is used as multiplexer in fast Lonworks environments • Economically, a very attractive offer as there are no costs for the external multi- plexer. • High data throughput of 1.2 Mbit/s on a sturdy, industry-proof bus. Configuration software • Short learning time thanks to integrated wizard • Multi-language platform • All configuration parameters are saved in the reader. • Independent of the installed hardware interface

Introduction Date of issue 06/13/2005 13 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com 5.2 Available models The VB34 scanner is available in various versions, which differ in the following features: • Optical system (head) • Decoder (base assembly) The following models are available: 5.3 Displays The VB34 decoder base assembly has an LCD display for system messages and menus of the configuration software. The three keys on the side of the display are used for navigating in the menus of the configuration software (Figure 3.3). The three status LEDs have the following functions: Power ON (Red) indicates that the reader is switched on (Figure 3.3) Phase ON (Yellow)indicates that the presence sensor is activated (Figure 3.3). TX Data (Green)indicates that the primary serial interface transmits data without errors (Figure 3.3). 5.4 Oscillating mirror models Oscillating mirror models are used when large reading areas must be covered, mainly in the case of horizontal barcodes (picket fence barcodes). The VB34 contains a special optical head with an integrated oscillating mirror, which is driven by a linear motor. Speed, precision, repeatability and reliability of this drive technology guarantee a high performance. The new oscillating mirror is completely software-controlled and programmable. The configuration™ software makes it possible to adjust the speed of the linear motor (and thus the oscillation frequency) as well as the upper and lower end position for the oscillation process as an angle. If the oscillating mirror is programmed to read barcodes at a very small angle, position the reader in such a way that the visual angle is at least 10° (Chapter 6.4). This angle mirrors the smallest deflection or the scanning line that is closest to the horizontal. All other scanning lines have a visual angle of more than 10°. This prevents a direct reflection of the laser beam emitted by the reader. VB34 - xxxx - OM - y Max. distance Decoder model (base assembly) __ = master/slave Optical model (head) P = Profibus _ = Standard B12 = Ethernet OM = Oscillating mirror B7 = DeviceNet

Introduction Date of issue 06/13/2005 14 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Figure 5.1 Visual angle for oscillating mirror models Otherwise, the scanner can be installed with a tilt angle of 17.5° in order to achieve a horizontally symmetric deflection range. Figure 5.2 Reading position of the oscillating mirror In the above example, the zone in which the scanning lines meet the reflecting surface vertically corresponds to a neutral area in the middle of the reading field. The mirror can be deflected by up to 40°. In relation to the central axle of the exit window, the deflection angle is asymmetric. Figure 5.3 Maximum deflection and asymmetry of the oscillating mirror

Introduction Date of issue 06/13/2005 15 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com By configuring the oscillating mirror speed to 19 Hz, a raster for recording and reading quickly moving objects can be reproduced. The oscillating angles are selected in the software. The minimum and maximum values are –2.5° and +37.5° respectively. The scanner can be tilted so that the software setting of 17.5° lies on the horizontal as a 0° reference. Figure 5.4 End angle position for the oscillating mirror These models have a higher read rate (1200 read processes/second) than the standard models, which is not influenced by the oscillating mirror. The following example shows a setting of +10° for the lower line and an angle of +20° for the upper line (see figure below). Figure 5.5 Oscillating mirror operation For details on mounting oscillating mirror model, please refer to Chapter 6.2.1. Hz Max. deflection 0 ... 5 40° 6 ... 10 30° 11 ... 15 20° 16 ... 19 10° The number of scans on a given reading area can be increased by limiting the raster width to the required minimum. Note

Installation Date of issue 06/13/2005 16 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com 5.5 Accessories For the VB34, the following accessories can be ordered: 6 Installation To install the system, proceed as follows • Select the installation location for the VB34. • Install the VB34 reader. • Establish all electrical connections to the system. • Direct the reader to the barcodes. • Install the configuration software on the PC. • Configure the dynamic Flash™ focussing using the configuration software. 6.1 Contents of the package When opening the packaging, make sure that the VB34 reader is undamaged and that all parts of the following packing list are contained in the packaging. This packing list contains: • VB34 reader • Instruction manual • CD-ROM with the configuration software • Mounting angle and screws Accessories Description CAB-6002 SH3339 Cable on C-BOX 100, 2 m length CAB-6005 SH3339 Cable on C-BOX 100, 5 m length CAB-6012 SH3339 Cable on C-BOX 100, 2 m length (VB34 fieldbus version) CAB-6015 SH3339 Cable on C-BOX 100, 5 m length (VB34 fieldbus version) CAB-6102 Master/slave cable, 2 m length CAB-6105 Master/slave cable, 5 m length CAB-6112 Master/slave cable, without supply, 2 m CAB-6115 Master/slave cable, without supply, 5 m INT-60 20 mA interface card GFC-600 90° near range deflecting mirror C-BOX 100 Passive connection box C-BOX 300 Profibus DP connection box BTK-6000 Termination networks set (5 units) FBK-6000 Quick mounting bracket (2 parts) GFC-60 90° deflecting mirror US-60 Mounting angle set (5 units) for multiple-side stations If in your system the VB34 reader is connected to a C-BOX100, please refer to the details in section "Additional documentation". Note

Installation Date of issue 06/13/2005 17 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Figure 6.1 VB34 - contents of the package 6.2 Mechanical installation 6.2.1 Installation of the reader Thanks to Step-a-Head™, the VB34 reader can be adjusted and installed in the ideal reading position. By separating the head and the base assembly, you can change the adjustment of the decoder base assembly and thus of the display, key pad and connectors, while the head with the optical reading system maintains its optimum position. The head and the base assembly can be turned independently of each other, thus making a successful installation possible even in critical environments . Figure 6.2 Step-a-Head™ function To turn the head of the reader, perform the following steps: 1. Remove the head from the base by the unscrewing the four fixing screws. 2. Turn the head into the desired position. 3. Unscrew the two screws on the head. 4. Fix the head on the base assembly by tightening the four fixing screws again. 5. Tighten the two screws on the head. The following figures show the total dimensions of the standard model, the oscillating mirror model and the mounting angles for installation. For a description of the alignment of the reader in relation to the read zone, please refer to Chapter 6.5. Head screws Fixing screws

Installation Date of issue 06/13/2005 18 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Figure 6.3 Dimensions VB34 Figure 6.4 Dimensions of mounting angle ST-237

Installation Date of issue 06/13/2005 19 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Figure 6.5 Dimensions of VB34 oscillating mirror model Figure 6.6 Dimensions of mounting angle ST-210

Installation Date of issue 06/13/2005 20 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com 6.2.2 Installation of the reader with accessories The following accessories make it possible to install the VB34 reader in the ideal position for network layout: • ST-237 mounting angle • ST-210 mounting angle • FBK-6000 quick mounting bracket ST-237 is a mounting angle with 105° for mounting the reader as shown in the following figure: Figure 6.7 Fixing the ST-237 mounting angle ST-210 is a mounting angle with 90° for mounting the reader as shown in the following figure: Figure 6.8 Fixing the ST-210 mounting angle FBK-6000 is a quick mounting bracket set for easily and quickly mounting the reader in ST-210 or ST-237 mounting angles. First, the FBK-6000 mounting bracket must be fixed to the VB34 reader by means of the screws: Figure 6.9 Fixing the FBK-6000 mounting bracket to the reader

Installation Date of issue 06/13/2005 21 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Afterwards, fix the assembly to the mounting angle by hanging the hook into the recess of the mounting angle. Fix the assembly by means of 2 screws: Figure 6.10 Fixing the assembly to the mounting angle 6.3 Electrical connections The individual reader models have the following connectors: Reader model Connector Master/slave 25-pin connector for interface and input/output connections 9-pin connector, Lonworks 9-pin socket, Lonworks EtherNet 26-pin connector for interface and input/output connections 9-pin socket, Lonworks RJ45 connector DeviceNet 26-pin connector for interface and input/output connections 9-pin socket, Lonworks 5-pin connector Profibus 26-pin connector for interface and input/output connections 9-pin socket, Lonworks 9-pin socket, Profibus

Installation Date of issue 06/13/2005 22 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com The following table shows the assignment of the connectors on the terminal block of the C-BOX 100. Use this connection layout if the VB34 reader is connected to a net- work via the C-BOX 100: Connectors on the terminal block of the C-BOX 100 Power supply 1, 3, 5 VS 2, 4, 6 GND 7, 8 Grounding 20, 40 Reserved Inputs 27 EXT TRIG A (polarity exchangeable) 28 EXT TRIG B (polarity exchangeable) 29 IN 2A (polarity exchangeable) 30 IN 2B (polarity exchangeable) 31, 33 IN 3A (polarity exchangeable) 32, 34 IN 4A (polarity exchangeable) 36 IN 3B/IN 4B reference earth (polarity exchangeable) Outputs 21 Out 1+ 22 Out 1- 23 Out 2+ 24 Out 2- 25 Out 3A (polarity exchangeable) 26 Out 3B (polarity exchangeable) Secondary interface 35 TX AUX 37 RX AUX 38, 39 GND Primary interface RS232 RS485 full duplex RS485 half duplex 20 mA (only INT-60) 11, 15 TX232 TX485+ RTX485+ CLOUT+ 12, 16 RTS232 TX485- RTX485- CLOUT- 17 RX232 RX485+ CLIN+ 18 CTS232 RX485- CLIN- 10, 14, 19 SGND Signal ground SGND Signal ground SGND Signal ground 9, 13 RS485 Shielding RS485 Shielding

Installation Date of issue 06/13/2005 23 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com 6.3.1 Primary/secondary interface and I/O connections The VB34 reader has a 25-pin Sub-D connector for connection to computer, voltage supply and input/output signals. The fieldbus models (Ethernet, DeviceNet and Profibus) of the VB34 are equipped with a 26-pin connector instead of the 25-pin connector. The connection layout of this connector is shown in the following table: Figure 6.11 26-pin connector 25-pin connector * Pin 26 is only present on fieldbus models (Ethernet, DeviceNet or Profibus). VB34 connection layout of the 25/26-pin Sub-D connector Pin Description Function 1 Shield The shielding is internally connected with chassis ground via a capacitor. 20 RXAUX Received data of the RS232 interface (ground-related) 21 TXAUX Transmitted data of the RS232 interface (ground- related) 8 Out 1+ Plus lead of the digital output 1 22 Out 1- Minus lead of the digital output 1 11 Out 2+ Plus lead of the digital output 2 12 Out 2- Minus lead of the digital output 2 16 Out 3A Digital output 3 - polarity exchangeable 17 Out 3B Digital output 3 - polarity exchangeable 18 EXT_TRIG A External trigger (polarity exchangeable) 19 EXT_TRIG B External trigger (polarity exchangeable) 6 IN 2A Input signal 2 (polarity exchangeable) 10 IN 2B Input signal 2 (polarity exchangeable) 14 IN 3A Input signal 3 (polarity exchangeable) 15 IN 4A Input signal 4 (polarity exchangeable) 24 IN_REF Common reference earth for IN3 and IN4 (polarity exchangeable) 9, 13 VS Supply voltage - plus 23, 25, 26* GND Supply voltage - minus (ground)

Installation Date of issue 06/13/2005 24 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com ** For 20 mA current loop, GND lies on the ground potential of the reader voltage supply. Primary interface The primary serial interface supports the following interface standards: • RS232 • RS485 full duplex • RS485 half duplex • 20 mA current loop The 20 mA interface is only available if the INT-60 accessory option is installed. This accessory interface replaces the RS232/RS485 interface. For details on the connection and mode of operation of the primary interface, please refer to the following sections. RS232 interface In conjunction with a computer, the data of read codes and the configuration of the reader are transmitted via this interface. Depending on the model, the following pins the 25 or 26-pin connector are used for the RS232 interface: The RTS and CTS signals control the data transmission and ensure the synchronisation of the two communication partners. Connection layout of the connector for the primary interface Pin RS232 RS485 full duplex RS485 half duplex 20 mA (only INT-60) 2 TX TX485+ RTX485+ CLOUT+ 3 RX RX485+ CLIN+ 4 RTS TX485- RTX485- CLOUT- 5 CTS RX485- CLIN- 7 GND_ISO GND_ISO GND_ISO GND** Interface type and transmission parameters (baud rate, data bits etc.) are configured using the configuration software. For further information, please refer to section "Main Serial Port" in the online help. Pin Description Function 2 TX Send 3 RX Receive 4 RTS RTS (request to send) 5 CTS CTS (clear to send) 7 GND_ISO Signal ground Note

Installation Date of issue 06/13/2005 25 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com If the RTS/CTS handshake protocol is active, the VB34 reader sets the RTS output in order to indicate that it wants to transmit a message. The receiver activates the CTS to start the transmission. Figure 6.12 Connection layout of the RS232 interface RS485 interface (full duplex) The RS485 full-duplex interface is suited for continuous (not running in dialog operation) communication protocols in point-to-point configuration. In this case, greater distances and a higher tolerance towards electrical interfering signals compared with the RS232 interface can be realised. In full-duplex operation, the RS485 interface uses the following pins of the 25-pin or 26-pin connector: Figure 6.13 Connection layout of the RS485 interface (full duplex) RS485 interface (half duplex) The RS485 interface in half-duplex operation is suited for Multidrop connections with a VISOLUX Multiplexer or for master/slave configurations. In half-duplex operation, the RS485 interface uses the following pins of the 25-pin or 26-pin connector: Pin Description Function 2 TX485+ RS485 output (+) 3 RX485+ RS485 input (+) 4 TX485- RS485 output (-) 5 RX485- RS485 input (-) 7 GND_ISO Signal ground

Installation Date of issue 06/13/2005 26 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Figure 6.14 Connection layout of the RS485 interface (half duplex) 20 mA current loop (only with INT-60 accessory option) If the INT-60 accessory card is installed, the VB34 has a 20 mA current loop as the interface. The INT-60 card supports the operation as passive or as active current loop, i.e. as sink or source. Wiring as source In the case of an operation as source, the 26-pin connector is wired as follows: ** For 20 mA current loop, GND lies on the ground potential of the reader voltage supply. Figure 6.15 20 mA current loop, wiring as source (active) If the VB34 reader is connected to a C-BOX 100 via a CAB-61X0, the signals are connected to the following terminals of the C-BOX 100: Pin Description Function 2 RTX485+ RS485 input/output (+) 4 RTX485- RS485 input/output (-) 7 GND_ISO Signal ground Pin Description Function 4 CLOUT- Current loop output (-) 5 CLIN- Current loop input (-) 7 GND Grounding* Pin Description Function 12, 16 CLOUT- Current loop output (-) 5 CLIN- Current loop input (-) 10, 14, 19 GND Grounding*

Installation Date of issue 06/13/2005 27 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Wiring as sink In the case of an operation as sink, the 26-pin connector is wired as follows: Figure 6.16 20 mA current loop, wiring as sink (passive) If the VB34 reader is connected to a C-BOX 100 via a CAB-61X0, the signals are connected to the following terminals of the C-BOX 100: Secondary interface The secondary serial interface is designed as a fixed RS232 full-duplex interface. The interface is configured using the configuration software. In full-duplex operation, the RS232 interface uses the following pins of the 25-pin or 26-pin connector: Pin Description Function 2 CLOUT+ Current loop output (+) 4 CLOUT- Current loop output (-) 3 CLIN+ Current loop input (+) 5 CLIN- Current loop input (-) Pin Description Function 11, 15 CLOUT+ Current loop output (+) 12, 16 CLOUT- Current loop output (-) 17 CLIN+ Current loop input (+) 18 CLIN- Current loop input (-) Pin Description Function 20 RXAUX Received data 21 TXAUX Transmitted data 23 SGND AUX Signal ground 5

Installation Date of issue 06/13/2005 28 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Figure 6.17 Connection layout of the RS232 interface Inputs The inputs of the reader are lead through on the 25-pin or 26-pin connector (Figure 6.11) of the VB34. The inputs are labelled EXT_TRIG, IN2, IN3 and IN4. IN2 is normally used as encoder input. In the PackTrack™ operating mode, this input is used to measure the speed of the band. EXT_TRIG is the primary presence sensor. An active signal at this input informs the reader that a code is to be read and decoded. A (yellow) LED indicates that the EXT_TRIG signal is active. IN3 and IN4 can be used as stop signal for the read cycle. All inputs are galvanically isolated by means of optocouplers, independent of polarity and are supplied via a constant current generator. The control signal is lead via a debounce filter with a delay of 5 ms or 500 ms. EXT_TRIG, IN3 and IN4 work with the same filter constant, which is usually set to 5 ms for photo cells, whereas IN2 is operated with a filter constant of 500 ms if an encoder is connected. Figure 6.18 Input wiring with control via PNP signal Pin Description Function 18 EXT_TRIG A External trigger (polarity exchangeable) 19 EXT_TRIG B External trigger (polarity exchangeable) 6 IN2A Input signal 2 (polarity exchangeable) 10 IN2B Input signal 2 (polarity exchangeable) 14 IN3A Input signal 3 (polarity exchangeable) 15 IN4A Input signal 4 (polarity exchangeable) 24 IN_REF Common reference earth for IN3 and IN4 (polarity exchangeable)

Installation Date of issue 06/13/2005 29 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Figure 6.19 Input wiring with control via PNP signal Figure 6.20 Input wiring with control via NPN signal Figure 6.21 Input wiring with control via NPN signal Figure 6.22 Input wiring with control via PNP signals

Installation Date of issue 06/13/2005 30 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Figure 6.23 Input wiring with control via NPN signals The inputs can be powered via the VS signal of the reader (pin 9). For a galvanic isolation of control and reader, however, a supply with external voltage (Vext) instead of the voltage connected to pin 9 of the 25/26-pin connector is required. For reasons of simplicity, the control logic for the input signals can be powered via the supply voltage of the reader, which is connected to the pins A (VS) and B (GND) of the connector. In this case, however, there is no galvanic isolation. The voltage on pins A and B of the input connector is identical to the supply voltage of the scanner. The characteristic values of these inputs are: Maximum voltage 30 V Maximum current 10 mA Outputs Three outputs are available: The function of the three outputs OUT1+, OUT2+ and OUT3+ can be defined by the user. Please refer to the online help for further information. In the default setting, OUT1+ is connected with the COMPLETE READ event, which activates the output after a code has been read correctly. If the reader was programmed to read multiple codes in a read cycle, the event is triggered and the output is activated after all codes have been read. Pin Description Function 8 Out 1+ Plus lead of the digital output 1 22 Out 1- Minus lead of the digital output 1 11 Out 2+ Plus lead of the digital output 2 12 Out 2- Minus lead of the digital output 2 16 Out 3A Digital output 3 - polarity exchangeable 17 Out 3B Digital output 3 - polarity exchangeable

Installation Date of issue 06/13/2005 31 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com OUT2+ is linked with the NO READ event, which indicates that no code has been read. OUT3+ is linked with the NONE event, i.e. no event. This means that the output always maintains its status. The characteristic electrical values of the outputs OUT1+ and OUT2+ are: Maximum collector-emitter voltage 30 V Maximum collector current 130 mA Saturation voltage(VCE) 1 V at 10 mA max. Maximum power loss 90 mW at TU = 50 °C The limit defined by the maximum power loss is more important than the limit defined by the maximum collector current: if one of these outputs is continuously deactivated, the maximum current must not exceed 40 mA, even if up to 130 mA is permissible for pulsed operation. Figure 6.24 Connection layout of output 1 and output 2 OUT3+ is designed as a bidirectionally semiconductor relay with integrated current limit and has thus different characteristic electrical values. At an ambient temperature of 25°C, the maximum current through this output in continuous operation must not exceed 200 mA, in pulsed operating, up to 300 mA is permissible. At a maximum ambient temperature of 50°C, the maximum current is reduced to 160 mA (continuous) and 240 mA (pulse). The characteristic electrical values of OUT3+ are as follows: Maximum voltage 100 V Maximum collector current (pulse) 240 mA Ron 6 – 15 Ohm Roff > 500 Ohm Leakage current in Off status < 1 µA Maximum power loss 550 mW in TU = 50 °C Figure 6.25 Connection layout of output 3 The control signal runs through a filter with a delay of 50 µs for OUT1+ and OUT2+

Installation Date of issue 06/13/2005 32 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com as well as for 1 ms for OUT3+. If the load is powered by an external voltage supply, the voltage must be less than 30 V. 6.3.2 Lonworks connector The network used by VB34 is based upon a Lonworks communication system, for which only two leads (with exchangeable polarity) are required for a connection. Furthermore, the supply voltage is lead through to the connectors. In this way, all the slave readers can be supplied via the VISOLUX standard cable by the master. For applications, in which an increased range of functions is required for synchronization, the VB34 master issues two system signals with the descriptions Sys_I/O and Sys_Enc_I/O to the slave devices. If, for example, an application works with an encoder, the signal is received by the master and transmitted via the cable directly to all slave devices. The internal circuits, which generate the system signals, are powered externally via the pins VS_I/O and REF_I/O and are galvanically isolated from the voltage supply of the reader. These system circuits do not have to be used in all operating modes (see section 1.7 for additional information). To ensure that the system works without errors, only original cables and accessories should be used. The wiring must be in accordance with the example configurations (see section 1.7 for details). Figure 6.26 9-pin local Lonworks connectors VB34 electrical connections of the 9-pin Lonworks connectors Pin Description Function 1 Shield Shielding of the cable 9 VS Supply voltage - plus 2 GND Supply voltage - minus (ground) 6 VS_I/O Supply voltage of the I/O circuit 3 Ref_I/O Reference voltage of the I/O circuit 4 SYS_ENC_I/O System signal 5 SYS_I/O System signal 7 LON A Lonworks lead (polarity exchangeable) 8 LON B Lonworks lead (polarity exchangeable)

Installation Date of issue 06/13/2005 33 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Network termination When constructing a Lonworks system, it is important to terminate the network correctly. For this, a BTK-6000 termination network is connected to the VB34 master reader as well as to the last VB34 slave reader. This termination network is equipped with two connectors and can be connected to the 9-pin connector of the master or to the 9-pin socket of the last slave reader. Figure 6.27 BTK-6000 termination network Lonworks Interface The Lonworks network consists of readers with input and output, which can be connected to a multiple side or station-wide system. Generally, the VB34 master uses the 9-pin socket as the output to the first slave reader, while the 9-pin connector is completed with a BTK6000 termination network (see Chapter 6.7.2 for details). With a T network configuration, both connector plugs of the master are used for the two lead branches to the slave readers. Both connections are always used to connect slave readers. For this purpose, the 9- pin socket is used as the output and the 9-pin connector is used as the input. The socket on the last reader is terminated to complete the network. The following figure shows the connection of a VB34 as the master with a VB34 as the slave reader. For fieldbus models no external termination is required for the reader as this is already integrated. Note

Installation Date of issue 06/13/2005 34 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Figure 6.28 VB34 master/slave Lonworks connection The following figure shows the two network connections of the BTK-6000. In the figures, the termination is shown as T. The following figure shows the switching of the termination network. Figure 6.29 Circuit diagram of the BTK-6000 termination network The following figure shows the termination of a VB34 operated as the master with a BTK-6000 termination network. Figure 6.30 Termination of a VB34 master The following figure shows the termination of a VB34 operated as the slave with a BTK-6000 termination network. The maximum current consumption of a slave reader via the master is 2 A. Therefore, it makes sense to supply at the most 3 readers (master + 2 slave devices) with a 24 V power pack. Socket Connector Attention

Installation Date of issue 06/13/2005 35 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Figure 6.31 Termination of a VB34 slave The following figure shows the connection of a VB34 fieldbus model, which always acts as the master, with a VB34 reader operated as the slave. Figure 6.32 VB34 master/slave Lonworks connection 6.3.3 Ethernet connector This connector is only available with VB34 Ethernet models and allows for an Ethernet connection between the host and the reader. Figure 6.33 RJ45 cable connector Figure 6.34 VB34 RJ45 socket Connector and electrical connections (see the following table) correspond to IEEE 802.3 10 BaseT and IEEE 802.3U 100 BaseTx.

Installation Date of issue 06/13/2005 36 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Ethernet interface The Ethernet interface (NIC) can be used for the TCP/IP-based communication with external or local computers in a network or for the direct connection of a PC to the reader. The following example shows the network connection via a hub with an uncrossed cable (standard network cable) : Figure 6.35 Uncrossed cable The following example shows the direct connection of the reader to a PC with a crossover cable: Figure 6.36 Crossover cable For additional information, refer to document “Ethernet.pdf”, which is available as additional documentation. VB34 electrical connections of the RJ45 socket Pin Description Function 1 TX + Transmitted data (+) 2 TX - Transmitted data (-) 3 RX + Received data (+) 6 RX - Received data (-) 4, 5, 7, 8 N.C. unoccupied

Installation Date of issue 06/13/2005 37 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com 6.3.4 DeviceNet connector The 5-pin connector is only available with the DeviceNet model of the VB34 and allows for a connection between the reader and a higher-level system: Figure 6.37 5-pin DeviceNet connector 6.3.5 Profibus connector The 9-pin Profibus socket is only available with the Profibus model of the VB34 and allows for a connection between the reader and a higher-level system: Figure 6.38 9-pin Profibus socket When the DeviceNet is used, the primary serial interface is deactivated and must not be interfaced with another device. VB34 electrical connections of the 5-pin DeviceNet connector Pin Description Function 2 V + Supply voltage - plus 5 CAN_L CAN bus data lead – L 1 Shield Shield 4 CAN_H CAN bus data lead – H 3 V - Supply voltage - minus The supply voltage to the pins V+ and V- is only used to supply the part of the DeviceNet card, which is directly connected to the bus. It is galvanically isolated from the supply of the VB34, which has to be connected to the pins 9 and 13 as well as 23 and 25 of the 26-pin connector. Note Note

Installation Date of issue 06/13/2005 38 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com * optional ** optional, RS485 level Profibus interface The Profibus interface is used for communication with a higher-level system and allows for an extended network and remote diagnosis functionality of the reader. For additional information, refer to the document “Profibus_Fam6k.pdf”, which is available as additional documentation. 6.3.6 Voltage supply The supply voltage of an individual reader must lie between 15 and 30 V DC. In master/slave configurations, VISOLUX recommends a voltage supply with at least 24 V DC. The power consumption of the different VB34 models is slightly different. When several VB34 readers are connected in a master/slave configuration, the maximum power consumption per reader is 15 W. Starting the motor results in a peak demand of approx. 20 W for 5 to 10 seconds. Figure 6.39 Voltage supply via the 25-/26-pin connector VB34 electrical connections of the 9-pin Profibus socket Pin Description Function 1 Shield* Shield or protective earth 2 - unoccupied 3 B-LINE (RXD/TXD-P) Received / transmitted data P 4 CNTR-P** Repeater control signal 5 DGND Signal ground (M5V) 6 +5 V 5 V voltage plus (P5V) 7 - unoccupied 8 A-LINE (RXD/TXD-N) Received / transmitted data 9 CNTR-N** Repeater control signal

Installation Date of issue 06/13/2005 39 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com 6.4 Operator interface How to set up a simple test cable: The following figure shows a simple test cable with supply, an external trigger (push button) and the connection of the RS232 interface to a PC. Figure 6.40 VB34 test cable 6.5 Adjusting the reader The VB34 reader is able to read labels at most angles, however, a strong distortion can have an unfavourable effect on reading performance. When assembling the VB34, note the following three ideal angles for the label position: Tilt angle 0°, angle of rotation 10° to 30° and rotation 0°. Follow the proposals in the next paragraph how best to position the reader: The tilt angle is represented by the value P, see figure 41. Adjust the reader in such a way that the tilt angle is held as low as possible. RS232 connection assignment to the PC 9-pin connector 25-pin connector Pin Description Pin Description 2 RX 3 RX 3 TX 2 TX 5 GND 7 GND 7 RTS 4 RTS 8 CTS 5 CTS

Installation Date of issue 06/13/2005 40 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Figure 6.41 Tilt angle The angle of rotation is represented by the value S, see figure 42. Adjust the reader in such a way that the angle of rotation is at least 10°. This prevents a direct reflection of the laser beam emitted by the reader. With oscillating mirror models, this angle mirrors the smallest deflection or the scanning line that is closest to the horizontal. All other scanning lines have an angle of rotation of more than 10°. Figure 6.42 Angle of rotation The tilt angle is represented by the value T, see Figure 6.43. Figure 6.43 Tilt angle

Installation Date of issue 06/13/2005 41 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com 6.6 Typical installations 6.6.1 Standard installation The VB34 reader is fitted on a ST-237 mounting angle with 105° (see figure 4), which ensures an angle of rotation (S in the following figure) of 15° to the level of the image. (Generally, the angle of rotation should lie between 10° and 20°.) This prevents a direct reflection of the laser beam emitted by the reader. Furthermore, the mounting angle allows for an adjustment of the tilt angle (T in the following figure, generally 0°) for an optimum alignment of the reader: Figure 6.44 Standard installation 6.6.2 Installation with an angle of rotation of 45° The VB34 reader is fixed with a ST-210 90° mounting angle (Figure 6.6). Adjust the guides of the mounting angle in such a way that an angle of rotation (S in the following figure) 45° is achieved in order to avoid a direct reflection from the laser beam emanated from the reader. Figure 6.45 Installation with an angle of rotation of 45°

Installation Date of issue 06/13/2005 42 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com 6.7 Typical hardware configurations The following sections show typical examples for the system hardware configurations, for which a corresponding software configuration is required. For more detailed information, please refer to Chapter 7.2. For other hardware configurations, a VB34 reader with a special decoder base assembly may be required. The illustrated cable and accessories are original products. To ensure the functional capability and smooth operability of the system, it is recommended that you only use these products. 6.7.1 Point-to-point In a point-to-point arrangement, the data is transmitted both via the primary and secondary interface. The primary interface can be adjusted to the full-duplex communication in accordance with the RS232 or RS485 standard. Depending on the VB34 model, various hardware configurations are possible. Master/slave models During online operation, the reader is activated by an external trigger (light barrier) when an object enters the reading zone. In the following example, the signal is created via a C-BOX 100 to the VB34 reader, which also supplies the system. *) Presence sensor connected to the external trigger input. Figure 6.46 Point-to-point arrangement for master/slave models With the installation with an angle of rotation of 45° it is not ensured that the reader will achieve the same efficiency (see reading fields in Figure 8.3.1) as in the standard installation with angles of rotation between 10° and 20°. The mounting angle ST-210 is contained as an accessory for the VB34 standard model in the US-60 set. Attention Note

Installation Date of issue 06/13/2005 43 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Fieldbus models In this case, no external trigger is used. The C-BOX 100 is used only to supply the reader. The VB34 reader (as an Ethernet, DeviceNet or Profibus model) is connected to an external fieldbus host. It can be activated by a signal from the external host or always be active in automatic operation mode. *) Light barrier (presence sensor) connected to the external trigger input . Figure 6.47 Point-to-point arrangement for fieldbus models 6.7.2 Loops With the loop arrangement via the secondary interface, all VB34 models can be integrated into a network with different readers, without the need for a Lonworks interface. In this loop arrangement, two or more readers can be connected to a single external serial interface. Each VB34 reader also provides the messages, which it received on the secondary (RS232) interface, via the primary interface (also RS232). In this arrangement, several readers can be switched in series. The message passes through all the stations in the chain up to the host. The read cycles of the individual readers are independent of those of the other readers. In loop configurations, each reader has an own external trigger (several light barriers). For this purpose, a portable reader can also be included via the secondary serial interface in order to read codes manually. The maximum cable length for RS232 connections is 15 m. The following figure shows several VB34 readers in a loop arrangement.

Installation Date of issue 06/13/2005 44 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com *) Light barrier (presence sensor) connected to the external trigger input . Figure 6.48 Loop arrangement for VB34 master/slave models *) Light barrier (presence sensor) connected to the external trigger input . (1) Primary serial interface (2) Secondary serial interface Figure 6.49 Loop arrangement for fieldbus models

Installation Date of issue 06/13/2005 45 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com 6.7.3 RS232 master/slave In the RS232 master/slave arrangement, all VB34 models can be integrated into a network with different readers, without the need for a Lonworks interface. The readers operated as the slave only communicate via the primary and secondary RS232 interfaces. Each slave device also provides the messages, which it received on the secondary interface, via the primary interface. All messages are transmitted to the master. The master reader is connected via the primary RS232 interface and a C-BOX 100 to a computer. If the INT-60 accessory option is installed, a 20 mA current loop can be used. For the RS232 master/slave arrangement, a central external trigger signal is used (a light barrier). *) Light barrier (presence sensor) connected to the external trigger input . (1) Primary serial interface (2) Secondary serial interface Figure 6.50 RS232 master/slave for VB34 master/slave models The VB34 reader (master/slave variant only), which is used as the master in a RS232 network, can simultaneously be connected to a Lonworks network with VB34 slave readers. When assigning slave addresses, note that the number of the first Lonworks slave must follow on seamlessly to the number of the last slave reader in the RS232 network. If, for example, the RS232 network consists of the devices slave 1 and slave 2 , the first slave device in the Lonworks network is slave 3 (not slave 1). Note

Installation Date of issue 06/13/2005 46 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com *) Light barrier (presence sensor) connected to the external trigger input . (1) Primary serial interface (2) Secondary serial interface Figure 6.51 RS232 master/slave for VB34 master/slave fieldbus models 6.7.4 Multiplexer The Multiplexer layout serves to integrate VB34 slave readers into a Multidrop network, which consists of different readers without a Lonworks interface . All the readers are connected via the primary interface to a Multiplexer. In this instance, the primary interface is configured as the RS485 half duplex interface.

Installation Date of issue 06/13/2005 47 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com *) Light barrier (presence sensor) connected to the external trigger input . (1) Primary serial interface Figure 6.52 Multiplexer for VB34 master/slave models The secondary serial interface of the slave readers can be used to visualize the entered data or to configure via the configuration software. During online operation, the reader is activated by an external trigger (light barrier) when an object enters the reading zone. 6.7.5 Local Lonworks network In a local Lonworks network, up to 31 VB34 slave devices can be connected to a VB34 master reader. In real terms, the number of readers that can be used in the network depends on the system operating conditions, especially on the operating mode and the volume of data. The online operating mode (for additional information, see the configuration software online help) supports, for example, a maximum of 8 slave readers. With regard to the design of your network, always consider the following points: • from an electrical point of view, the network supports up to 31 VB34 readers with a network length of 130 m. • the maximum number of supported VB34 readers depends on how the system components are supplied. (For additional information, refer to Chapter 6.3.6.) Contact VISOLUX if you have to integrate a large number of readers into your network or if the data throughput in the application is extremely high. When you construct the network, the VB34 master reader must be connected via the 25-pin Sub-D connector to a local computer or to C-BOX 100. The first slave reader of the system is connected to the 9-pin Lonworks socket of the master, while the 9-pin Lonworks connector must be completed with a BTK-6000 termination network.

Installation Date of issue 06/13/2005 48 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com The slave readers are connected together via the Lonworks connector plug. The network must be completed with a BTK-6000 termination network on the 9-pin socket of the last slave reader. Central light barrier The presence sensor is connected to the C-BOX 100 and is used as the sole, central trigger source in the system. There is only one read cycle with a message from the master reader to the local host. The online operating mode is used in this layout. *) Presence sensor connected to the external trigger input. Figure 6.53 Central light barrier with 2 readers The following figure shows a system with four readers, which are supplied via two power packs. The master reader receives the external signals (triggers, serial host signals, etc.) and is supplied together with slave 1 by the first power pack via a C-BOX 100, while slave 2 and slave 3 are connected via a C-BOX 100 and the CAB610X cable to a second power pack. Each power pack supplies up to 2 readers. The CAB611X cable connects two separate groups: master and slave 1 as well as slave 2 and slave 3. In this instance, the voltage supply is not continued, only the network and synchronization signals are continued.

Installation Date of issue 06/13/2005 49 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com *) Light barrier (presence sensor) connected to the external trigger input . **) The power pack can be connected directly via a separate cable to slave 2 (2 wires with at least 0,5 mm² for VS + GND). Figure 6.54 Central light barrier with more than 2 readers and several power packs The following figure shows a system with five readers, in which the master reader receives the external signals (triggers, serial host signals, etc.) and is supplied together with slave 1 and slave 2 via a C-BOX 100, while slave 3 and slave 4 are connected via a CAB610X cable to a second power pack. This is necessary because the C-BOX 100 can supply a maximum of 3 readers. The CAB611X cable connects two separate groups: master, slave 1 and slave 2 as well as slave 3 and slave 4. In this instance, the voltage supply is not continued, only the network and synchronization signals are continued. Slave 3 is connected via a customer-specific, 2-wire cable (0,5 mm²) to the power pack (VS + GND). *) Light barrier (presence sensor) connected to the external trigger input . Figure 6.55 Central light barrier with more than 2 readers and central voltage supply

Installation Date of issue 06/13/2005 50 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Multiple light barrier (configuration available shortly). In this layout, up to 7 VB34 slave readers each have a separate light barrier and thus several read cycles. The light barrier, which controls the master reader, is connected via the C-BOX 100. The master transmits all the messages received via the Multidrop lead as well as its own messages to the C-BOX 100, which forwards them to the local host. The following figure shows a system with four readers, in which the fourth reader is supplied via a separate C-BOX 100 because a C-BOX 100 can supply a maximum of 3 readers. Therefore, the cable connecting the two separate groups does not carry over the supply. In this example, this is cable CAB611X between slave 2 and slave 3. *) Light barrier (presence sensor) connected to the external trigger input . Figure 6.56 Multiple light barrier with more than 3 readers 6.7.6 Fieldbus network Fieldbus models (Ethernet, Profibus and DeviceNet) enable communication in fieldbus environments without a converter or adapter. The VB34 fieldbus master communicates with the external host via a cable, which is connected to the fieldbus connector (Ethernet, Profibus or DeviceNet). This host can, for example, be an external PC with an IP address. The 9-pin Lonworks socket is used to connect the first slave device to the master, while the 26 Sub-D connector is used to supply the master via a C-BOX 100. The slave readers (VB34 master/slave models) are connected together via the Lonworks connector plug. The network must be completed with a BTK-6000 termination network on the 9-pin socket of the last slave reader. No termination network is required for the fieldbus master because the termination is already integrated.

Installation Date of issue 06/13/2005 51 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Central light barrier The VB34 master reader (as an Ethernet, DeviceNet or Profibus model) is connected to an external fieldbus host. It can be activated by a signal from the external host or always be active in automatic operation mode. *) Light barrier (presence sensor) connected to the external trigger input . Figure 6.57 Fieldbus layout with a central light barrier As already described, a C-BOX 100 can supply a maximum of 3 readers. If more than 3 readers are used, connect the different groups with a CAB611X cable, which does not loop in the supply lines, and supply the individual groups separately. 6.8 FLASH™ dynamic focusing An innovation of the VB34 is the linear motor, which can be used to control the reading position of the scanner via software. This dynamic system with the name Flash™ is able to assume any reading position from the minimum position to the maximum position. The Flash™ function is programmed via the configuration software (see the online help for details) and has the following operating modes: • Fixed adjustment • Continuous adjustment • Trigger operating mode • D-Flash™ operating mode

Installation Date of issue 06/13/2005 52 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com 6.8.1 Fixed adjustment With fixed adjustment, the read distance (in cm/inch) is adjusted as fixed to the desired position per software. This is the most simple Flash™ function, during which the focus position is adjusted per software before use in the application and stored in the decoder of the reader. This function is similar to the focus adjustment of the VB33 reader, however, with the major difference that in terms of software the adjustment is made using the configuration program and not manually via an adjustment screw. Figure 6.58 Flash™ fixed adjustment 6.8.2 Continuous adjustment With continuous adjustment, the focus position is continuously adjusted with a defined frequency (f1 in the following figure) between minimum and maximum. This Flash™ function makes it possible to use the entire read range of the VB34 if the objects to be recognized are large and move slowly. Typical areas of application for continuous adjustment are reading the front of large pallets or objects on a fork lift truck. Figure 6.59 Flash™ continuous adjustment 6.8.3 Trigger operating mode In the trigger operating mode, the focus position is adjusted depending on an external input signal (light barrier, message via the serial interface…). This is the traditional Flash™ function, for which light barriers or a separate interface to the host (PC or PLC) are required. The excellent capability of the VB34 optical system platform makes it possible to cover an area of 800 mm x 800 mm with a code resolution of 38 mm using only one light barrier.

Installation Date of issue 06/13/2005 53 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Figure 6.60 Flash™ trigger operating mode 6.8.4 D-Flash™ operating mode In the D-Flash™ operating mode, the focus position is changed depending on the measured distance (Dn in the following figure) between the reader and the object to be read. This innovative and highly flexible function presents the software with extensive possibilities. The D-Flash™ development is based upon the measured minimum distance. This makes it suitable for a variety of applications. If necessary, D-Flash™ can be tailored to meet the requirements of a specific application and developed further. Figure 6.61 Flash™ D-Flash™ operating mode 6.9 Key field and display The VB34 key field makes it possible to call a menu using the following functions: • Internal Net • Test mode These adjustments can also be made via the configuration software. (For additional information, refer to Chapter 7.) 6.9.1 Internal Net This sub menu is used to configure the VB34 reader in a master/slave network. Here, the function of the reader (slave/master) in the network as well as, if configured as a slave, the address are defined. To call the Internal Net sub menu and configure the reader, carry out the following steps: 1. Keep the keys ▲ (arrow up) and ▼ (arrow down) depressed for 2 seconds at the same time to call the main menu. 2. Press the key ▲ (arrow up) or ▼ (arrow down) to select the “Internal Net ” menu option and press ENT (Enter) to call the option. 3. Press the keys ▲ (arrow up) or ▼ (arrow down) to select the “LonWAddrSel” menu option and press ENT (Enter) to call the option. 4. Select the reader function using the keys ▲ (arrow up) and ▼ (arrow down):

Software configuration Date of issue 06/13/2005 54 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com “MASTER” for master, “Slave n” for slave or “Disabled” for deactivated. Press the key ENT (Enter) to call the option. 5. Press the key ▲ (arrow up) or ▼ (arrow down) to select the “Exit” menu option and press ENT (Enter) to call the option. Repeat this step to exit the main menu and to return to the originally active operating mode of the reader. 6.9.2 Test mode The test mode is very useful during the installation phase because the reader is activated to check the optical adjustments as well as the reading position of the barcodes. To call the Test Mode sub menu and configure the reader, carry out the following steps: 1. Keep the keys ▲ (arrow up) and ▼ (arrow down) depressed for 2 seconds at the same time to call the main menu. 2. Press the key ▲ (arrow up) or ▼ (arrow down) to select the “Test Mode” menu option and press ENT (Enter) to call the option. The reader switches to test mode. 3. Press the key ▲ (arrow up) to exit the test mode. 4. Press the key ▲ (arrow up) or ▼ (arrow down) to select the “Exit” menu option and press ENT (Enter) to call the option. The reader exits the main menu and returns to the previous operating mode. 7 Software configuration 7.1 Software installation The new configuration software offers a number of important special features: • Assistant-based approach for less experienced users • Multi-lingual version • Defined configuration is stored directly in the reader. • A communication protocol independent of the used interface allows for the hard- ware-independent treatment of the reader as an external object, which is config- ured and monitored. To install the software, carry out the following steps: 1. Switch on the PC, on which the configuration software is to be used, and start Windows. 2. Insert the CD-ROM into the drive. 3. Wait until the installation program from the CD has started and then follow the installation procedure.

Software configuration Date of issue 06/13/2005 55 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com 7.2 Hints on quick configuration 7.2.1 Assistant for quickly setting up the reader After installing the configuration software (Chapter 7.1) the system displays the following window in which the user can select the desired configuration type: Figure 7.1 Start window for configuration program Less experienced users should select the option "Wizard", where an Assistant will guide you step by step through the configuration of the reader. The following parameters must be defined: • Selection and definition of the barcodes • Selection and definition of the operating mode (for more information, see the follow- ing sections) • Configuration of the digital inputs/outputs • Selection of the hardware interface • Configuration of the data output format After the parameters have been defined, the system displays the following window for completing the configuration of the reader with the following options: • Save configuration on disk • Change to enhanced configuration • Send configuration to the reader

Software configuration Date of issue 06/13/2005 56 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Figure 7.2 Completion window of the Configuration Assistant Test operating mode Figure 7.3 Selecting the test operating mode In the test mode, the reader is continuously activated in order to check the optical adjustments as well as the reading position of the barcodes. This operating mode should be used during the installation phase of the reader. After 100 read processes, the read data and an internal counter are displayed and output via the serial interface. The counter contains the percentage of the successful read processes.

Software configuration Date of issue 06/13/2005 57 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Online operating mode Figure 7.4 Selecting the online operating mode This operating mode instructs the reader to evaluate the external presence sensor at the input EXT TRIG+ and EXT TRIG. If the presence sensor is active, the VB34 reader attempts to enter and decode the code. If the decoding cycle is completed successfully, the barcode data is transmitted via the serial interface. Otherwise, a message stating that no data was read is transmitted. Automatic operating mode Figure 7.5 Selecting the automatic mode No connection to an external presence sensor is required for this operating mode. In this operating mode, the reader scans automatically and activates the read cycle when a barcode enters the read zone of the reader. The reader stops after an adjustable number of empty scans. The barcode data is transmitted via the serial Interface. If a read cycle is completed without a result, no message is transmitted to the computer.

Software configuration Date of issue 06/13/2005 58 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com 7.2.2 Network Assistant The Network Assistant allows you to define the models and number of slave readers in the Lonworks network. The configuration software identifies the device type by means of a code number. The code number is displayed in the relevant device window. The following code numbers are assigned to the device types: Since this tool is only available for a VB34 master, your reader must first be configured as the master as shown in the following figure: Figure 7.6 Network setting of the local device After that, the network settings can be defined by starting the Network Assistant: 1. If the Assistant cannot be started, activate the cluster configuration by clicking the symbol in the toolbar. After that, the “Devices” device window will ap- pear next to the Explorer window parameter. Figure 7.7 Cluster configuration Device type Code number VB33-2000-XX DS6300-100-XXX VB33-2000-OM-XX DS6300-105-XXX VB34-2500-XX DS6400-100-XXX VB34-2500-OM-XX DS6400-105-XXX

Software configuration Date of issue 06/13/2005 59 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com 2. Click the push button in the “Devices” device window in order to open the dialog field of the Network Assistant: Figure 7.8 Network Assistant a) If the slave readers are already configured and wired with the network, click the autodetect button in order to start the network query. All the devices that were found are listed in the “Current Devices” area. From the “Current Devices” area, select the desired slave reader and click the symbol in order to transfer the reader to the “Requested Devices” area in which you configure the network. You can also drag and store the device into this area by keeping the mouse button depressed. b) If the slave readers have not yet been configured and connected to the network, click the symbol in order to add a new device to the configuration. During this process, you also have to enter the model and device address. The slave reader you added will then appear in the “Current Devices” area. 3. If you want, select the transferred/added slave readers in the “Requested Devices” area and click the symbol in order to edit the description of the reader. 4. After your network has been configured, close the Network Assistant. Before closure, the program shows a dialog field containing the query whether you would like transmit the new configuration to the master. Select the option “Yes” in order to start this operation. 7.3 Enhanced configuration The ADVANCED option at the start of the configuration program is directed at experienced users, who would like to configure the reader in all details without the Assistant. After selecting this option, you can create a new reader configuration or open or change an existing one. The parameters are defined in the following window, which contains an Explorer-like organization structure:

Software configuration Date of issue 06/13/2005 60 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Figure 9 - Parameters in the Explorer window If required, to help you make the setting, an Online help is available, which is represented in an HTML browser. It is called via the configuration help option in the help menu. Furthermore, after selecting the desired parameter, a context-sensitive help is available via the key. 7.4 Basic settings for parameters The following table describes the default settings for VB34. The configuration software also allows the current parameter settings to be compared with the default settings. In the Tools menu. select the "Compare parameters" option in order to compare the current configuration with the default setting.

Software configuration Date of issue 06/13/2005 61 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Parameters Basic setting Code definition Code combination Message if read process without result String if read process without result Label code settings no. 1 Code symbology Length of label Minimum of code position Maximum of code position Check digit Decoding complexity Comparison string Label code settings no. 2 Code symbology Length of label Minimum for label length Maximum for label length Minimum of code position Maximum of code position Check digit Decoding complexity Comparison string Single label Global message if read process without result Interleaved 2 from 5 8 0 255 Deactivated 3 Empty Code 39 Variable 1 48 0 255 Deactivated 3 Empty Operating modes Operating mode selection Online options Start input number Active level for start input Timeout for read cycle Statistical data Online Online input 1 1 Active when closed Deactivated Deactivated Read system layout Device assignment Independent Read parameters Beam lock Overflow relationship Read operating mode Deactivated 7 Reconstruction Reconstruction parameters Max. scan gaps Max. stack codes 5 1 Scan lines amplitude Release of amplitude setting Deactivated

Software configuration Date of issue 06/13/2005 62 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Flash Flash operating mode Deactivated Data communication settings Host application protocol type Standard Data format Send start section Termination string after message with reading without results Trigger selection for sending the message Parameters Opening text Code direction ID Code ID Termination string Separators for data packets Setting for code field length With data Activated After decoding Deactivated Deactivated Variable length Primary serial interface Transmitted data Parameters Communication type of primary interface Interface standard of primary interface Handshake Baud rate Parity Data bits Stop bits Activated Standard RS232 off 9600 none 8 1 Secondary serial interface Transmitted data Loop Parameters Baud rate Parity Data bits Stop bits Activated Deactivated 115200 off 8 1 Parameters Basic setting

Optical properties Date of issue 06/13/2005 63 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com 8 Optical properties 8.1 ACR technology (ACR™ 3 reconstruction) The traditional method of reading barcodes can be described as “linear reading”. Under this method, the laser beam passes across the barcode symbol from the start to the end, as shown in the following figure: Settings for digital inputs/outputs Filter settings of digital inputs Anti-disturbance hardware for inputs 1, 3 and 4 Anti-disturbance hardware for input 2 Operating mode has priority before active input 1 Operating mode has priority before active input 2 Operating mode has priority before active input 3 Operating mode has priority before active input 4 5 ms 500 µs Active when closed Active when closed Active when closed Active when closed Output 1 Lead status Activating event Alternative activating event Deactivating event Alternative deactivating event Deactivating timeout (ms) NC Reading completed Repeated reading Timeout off 50 Output 2 Lead status Activating event Alternative activating event Deactivating event Alternative deactivating event Deactivating timeout (ms) NC Reading without result Partial reading Timeout off 50 Output 3 Lead status Activating event Alternative activating event Deactivating event Alternative deactivating event NC off off off off Parameters Basic setting

Optical properties Date of issue 06/13/2005 64 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Figure 8.1 Linear reading With the ACR technology it is no longer necessary for the laser beam to pass across the entire barcode in one go. The VB34 is able to reconstruct the barcode from a series of partial scans, which are possible if the label itself is moving. The following figure shows a typical example of a series of partial scans: Figure 8.2 Partial scans None of the partial scans contains the complete barcode. The decoder aligns the individual partial scans correctly to each other and combines them in the correct sequence thereby creating the complete code. The partial scans are aligned using the time difference between the partial scans, which is calculated via reference elements in the code. 8.1.1 Tilt angle for the ACR reconstruction The most important parameter in the detection with ACR technology is the maximum tilt angle (a max), under which a code can still be reconstructed. Figure 8.3 Rotation angle The calculation of the maximum angle for a is affected by different parameters, such as: height of label, number of read processes per second, code motion speed, etc. To determine the maximum value for a in your application, get in touch with your Pepperl+Fuchs contact person. Note that the decoder can read the label under a rotation angle between +αmax and

Optical properties Date of issue 06/13/2005 65 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com -αmax as shown in the following figure: Figure 8.4 Read zone with α max 8.2 PackTrack™ PackTrack™ is a patented operating mode for position-independent read stations. It makes it possible to read and correctly assign codes on different objects, which exist in the reading zone of the reader at the same time. For the PackTrack™ operating mode, an encoder and a presence sensor are required for tracking the moving targets. The entire PackTrack™ functionality is programmed via the configuration software. (Please refer to the online help for further information.) In the following example, the codes of two or more consecutive packets effectively lie in the reading zone at the same time. This results in a situation, in which the code of the second packet is read first, even before the code of the first packet. A system without PackTrack™ would assign the code of the second packet to the first packet and vice versa, thus causing a major sorting error. Figure 8.5 PackTrack™ system arrangement To ensure the function works correctly, the PackTrack™ operating mode needs to be calibrated after the readers have been installed. This step is absolutely necessary for

Optical properties Date of issue 06/13/2005 66 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com the reader to be able to recognize its own spacial position. This makes a fixed reference system necessary. The following figure shows this using a reference system which can be represented using the right hand (thumb = X axis, index finger = Y axis and middle finger = Z axis), where the Y axis corresponds with the direction of travel of the packets and the Z axis runs vertically to the conveyor belt upwards (see the following figure). Three barcodes are positioned in the scan line. Three coordinates are displayed for each of these barcodes. (The X axis corresponds with the light barrier line). Figure 8.6 PackTrack™ reference system 8.2.1 PackTrack™ calibration The reader can be calibrated via the configuration™ software. Select the “SPY” option from the Tools menu or click on the corresponding symbol in the configuration™ toolbar to show the following dialog field: Figure 8.7 Opening the digitizer window Absolute reference system All the readers receive 5 pieces of infor- mation via each barcode position: x, Y and Z (entered by the user) as well as the position in the scan line and distance (measured from the reader)

Optical properties Date of issue 06/13/2005 67 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Click the “GO” push button in the digitizer field to show the following window: Figure 8.8 Selecting the PackTrack™ calibration After selecting the “PackTrack Calibration” option in the Tools menu, another dialog field in which the calibration can be started will appear: Figure 8.9 Executing the PackTrack™ calibration After the code has been positioned to the desired position (position 1), enter the X, Y and Z code coordinates in the corresponding fields of the dialog field. Click the “Calibrate” push button to start the calibration. Repeat this process for position 2 and position 3. The “Focus position” field in the Flash™ command area makes it possible to adjust the focus position, while the “Run Test” push button makes it possible to test the calibration results and the efficiency. Before closing the dialog field, click the “Validate Calibration” push button to adopt the calibration adjustments.

Optical properties Date of issue 06/13/2005 68 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com 8.3 Read diagrams The read diagrams in the following figures clarify the conventions, which are used in the calculation of the minimum and maximum distances for reading barcodes. This procedure makes it possible to calculate the reading distance for your reader when using another focus adjustment than that specified in the read diagrams in Chapter 8.3.1 and Chapter 8.3.2 . Mark the minimum focus position with a straight vertical line. The points of intersection between this line and the global reading zone give the minimum reading distance. Figure 8.10 Calculating the reading zone Mark the external outline of the global reading zone with the origin (0,0) and a radial distance, which is equal to the maximum work distance of the reader. The points of intersection between this outline and the global reading zone give the maximum reading distance. 8.3.1 VB34 standard model VB34-2500 (standard), resolution: 0,20 mm (8 mils) The diagram shows a global reading zone, which is practically the sum of all the possible focus positions, and the reading zone, which results for the VB34 from a focus position of 650 mm and a barcode density of 0,20 mm (8 mils). The values for the maximum and the minimum distances are found in the radial distance curves in Figure 8.12.

Optical properties Date of issue 06/13/2005 69 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Figure 8.11 Read diagram of the standard model with 0,20 mm/8 mils Remark: (0,0) is the central position of the laser exit window. Conditions Code = interleaved 2 from 5 or code 39 PC = 0,90 Tilt angle = 0° Angle of rotation = 10° - 20° Tilt = 0°

Optical properties Date of issue 06/13/2005 70 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com The curves show the minimum and maximum radial distances. Figure 8.12 Radial distances for standard model with 0,20 mm/8 mils

Optical properties Date of issue 06/13/2005 71 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com VB34-2500 (standard), resolution: 0,25 mm (10 mils) The diagram shows a global reading zone, which is practically the sum of all the possible focus positions, and the reading zone, which results for the VB34 from a focus position of 900 mm and a barcode density of 0,25 mm (10 mils). The values for the maximum and the minimum distances are found in the radial distance curves in Figure 8.14. Figure 8.13 Read diagram of the standard model with 0,25 mm/10 mils Remark: (0,0) is the central position of the laser release window.

Optical properties Date of issue 06/13/2005 72 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Conditions Code = interleaved 2 from 5 or code 39 PC = 0,90 Tilt angle = 0° Angle of rotation = 10° - 20° Tilt = 0° The curves show the minimum and maximum radial distances. Figure 8.14 Radial distances for standard model with 0,25 mm/10 mils

Optical properties Date of issue 06/13/2005 73 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com VB34-2500 (standard), resolution: 0,30 mm (12 mils) The diagram shows a global reading zone, which is practically the sum of all the possible focus positions, and the reading zone, which results for the VB34 from a focus position of 1100 mm and a barcode density of 0,30 mm (12 mils). The values for the maximum and the minimum distances are found in the radial distance curves in Figure 8.16. Figure 8.15 Read diagram of the standard model with 0,30 mm/12 mils Remark: (0,0) is the central position of the laser release window.

Optical properties Date of issue 06/13/2005 74 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Conditions Code = interleaved 2 from 5 or code 39 PC = 0,90 Tilt angle = 0° Angle of rotation = 10° - 20° Tilt = 0° The curves show the minimum and maximum radial distances. Figure 8.16 Radial distances for standard model with 0,30 mm/12 mils

Optical properties Date of issue 06/13/2005 75 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com VB34-2500 (standard), resolution: 0,375 mm (15 mils) The diagram shows a global reading zone, which is practically the sum of all the possible focus positions, and the reading zone, which results for the VB34 from a focus position of 1400 mm and a barcode density of 0,375 mm (15 mils). The values for the maximum and the minimum distances are found in the radial distance curves in Figure 8.18. Figure 8.17 Read diagram of the standard model with 0,375 mm/15 mils Remark: (0,0) is the central position of the laser release window.

Optical properties Date of issue 06/13/2005 76 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Conditions Code = interleaved 2 from 5 or code 39 PC = 0,90 Tilt angle = 0° Angle of rotation = 10° - 20° Tilt = 0° The curves show the minimum and maximum radial distances. Figure 8.18 Radial distances for standard model with 0,375 mm/15 mils

Optical properties Date of issue 06/13/2005 77 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com VB34-2500 (standard), resolution: 0,5 mm (20 mils) The diagram shows a global reading zone, which is practically the sum of all the possible focus positions, and the reading zone, which results for the VB34 from a focus position of 1200 mm and a barcode density of 0,5 mm (20 mils). The values for the maximum and the minimum distances are found in the radial distance curves in Figure 8.20. Figure 8.19 Read diagram of the standard model with 0,50 mm/20 mils Remark: (0,0) is the central position of the laser release window.

Optical properties Date of issue 06/13/2005 78 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Conditions Code = interleaved 2 from 5 or code 39 PC = 0,90 Tilt angle = 0° Angle of rotation = 10° - 20° Tilt = 0° The curves show the minimum and maximum radial distances. Figure 8.20 Radial distances for standard model with 0,50 mm/20 mils

Optical properties Date of issue 06/13/2005 79 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com 8.3.2 VB34 model with reflex mirror VB34-2500-OM, resolution: 0,20 mm (8 mils) The diagram shows a global reading zone, which is practically the sum of all the possible focus positions, and the reading zone, which results for the VB34-2500-OM from a focus position of 600 mm and a barcode density of 0,20 mm (8 mils). The values for the maximum and the minimum distances are found in the radial distance curves in Figure 8.22. Figure 8.21 Read diagram of the oscillating mirror model with 0,20 mm/8 mils Remark: (0,0) is the central position of the laser release window.

Optical properties Date of issue 06/13/2005 80 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Conditions Code = interleaved 2 from 5 or code 39 PC = 0,90 Tilt angle = 0° Angle of rotation = 10° - 20° Tilt = 0° The curves show the minimum and maximum radial distances. Figure 8.22 Radial distances for oscillating mirror model with 0,20 mm/8 mils

Optical properties Date of issue 06/13/2005 81 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com VB34-2500-OM, resolution: 0,25 mm/10 mils The diagram shows a global reading zone, which is practically the sum of all the possible focus positions, and the reading zone, which results for the VB34–2500-OM from a focus position of 950 mm and a barcode density of 0,25 mm (10 mils). The values for the maximum and the minimum distances are found in the radial distance curves in Figure 8.24. Figure 8.23 Read diagram of the oscillating mirror model with 0,25 mm/10 mils Remark: (0,0) is the central position of the laser release window.

Optical properties Date of issue 06/13/2005 82 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Conditions Code = interleaved 2 from 5 or code 39 PC = 0,90 Tilt angle = 0° Angle of rotation = 10° - 20° Tilt = 0° The curves show the minimum and maximum radial distances. Figure 8.24 Radial distances for oscillating mirror model with 0,25 mm/10 mils

Optical properties Date of issue 06/13/2005 83 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com VB34-2500-OM, resolution: 0,30 mm/12 mils The diagram shows a global reading zone, which is practically the sum of all the possible focus positions, and the reading zone, which results for the VB34-2500-OM from a focus position of 1100 mm and a barcode density of 0,30 mm (12 mils). The values for the maximum and the minimum distances are found in the radial distance curves in Figure 8.26. Figure 8.25 Read diagram of the oscillating mirror model with 0,30 mm/12 mils Remark: (0,0) is the central position of the laser release window.

Optical properties Date of issue 06/13/2005 84 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Conditions Code = interleaved 2 from 5 or code 39 PC = 0,90 Tilt angle = 0° Angle of rotation = 10° - 20° Tilt = 0° The curves show the minimum and maximum radial distances. Figure 8.26 Radial distances for oscillating mirror model with 0,30 mm/12 mils

Optical properties Date of issue 06/13/2005 85 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com VB34-2500-OM, resolution: 0,375 mm/15 mils The diagram shows a global reading zone, which is practically the sum of all the possible focus positions, and the reading zone, which results for the VB34-2500-OM from a focus position of 1150 mm and a barcode density of 0,375 mm (15 mils). The values for the maximum and the minimum distances are found in the radial distance curves in Figure 8.28. Figure 8.27 Read diagram of the oscillating mirror model with 0,375 mm/15 mils Remark: (0,0) is the central position of the laser release window.

Optical properties Date of issue 06/13/2005 86 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Conditions Code = interleaved 2 from 5 or code 39 PC = 0,90 Tilt angle = 0° Angle of rotation = 10° - 20° Tilt = 0° The curves show the minimum and maximum radial distances. Figure 8.28 Radial distances for oscillating mirror model with 0,375 mm/15 mils

Optical properties Date of issue 06/13/2005 87 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com VB34-2500-OM - resolution: 0,50 mm/20 mils The diagram shows a global reading zone, which is practically the sum of all the possible focus positions, and the reading zone, which results for the VB34-2500-OM from a focus position of 1150 mm and a barcode density of 0,50 mm (20 mils). The values for the maximum and the minimum distances are found in the radial distance curves in Figure 8.30. Figure 8.29 Read diagram of the oscillating mirror model with 0,50 mm/20 mils Remark: (0,0) is the central position of the laser release window.

Optical properties Date of issue 06/13/2005 88 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Conditions Code = interleaved 2 from 5 or code 39 PC = 0,90 Tilt angle = 0° Angle of rotation = 10° - 20° Tilt = 0° The curves show the minimum and maximum radial distances. Figure 8.30 Radial distances for oscillating mirror model with 0,50 mm/20 mils

Maintenance Date of issue 06/13/2005 89 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com 9 Maintenance 9.1 Cleaning Clean the laser exit window (Figure 3.1/Figure 3.2) regularly to ensure the reader operates fault free. Dust, impurities etc. on the window can have a negative affect on the reading performance. Carry out cleaning in very dirty surroundings more frequently as required. Clean the window using a soft cloth moistened with alcohol. Do not use any abrasive cleaning agents. 10 Troubleshooting Guide on troubleshooting Clean the window of the VB34 when the reader is switched off or, at least, when the laser beam is not active. Before you contact your local Pepperl+Fuchs distributors, save the device configuration using the configuration program in a *.ddc file and make a note of the exact model and serial number of the device. Description of error Diagnostics/remedy Switch on The LED “voltage supply” does not light. • Is the voltage connected correctly? • If using a power pack, is this plugged in? • If using a supply connector, is this live? • If using a C-BOX 100, is the supply volt- age connected (check selector switch and LED)? Check whether you are working on a 25/ 26-pin connector or the spring-loaded terminals of a C-BOX 100. • Measure the voltage on pin 13 and pin 25 (for 25-/26-pin connectors) or on the con- tacts 1 and 2 (spring-loaded terminals C- BOX 100). Warning Note

Troubleshooting Date of issue 06/13/2005 90 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Online operating mode: The LED “Phase On” of the master does not light (when the external trig- ger is activated). • Check whether you are working on a 25/ 26-pin connector or the spring-loaded terminals of a C-BOX 100. • Is the sensor connected to the external trigger input EXT TRIG? • Is the light barrier supplied with electrical power? • Is one of the two EXT TRIG terminals (NPN output) supplied? • Is one of the two EXT TRIG terminals connected to ground (PNP output)? • Do the LEDs (if available) of the light bar- riers work trouble-free? • Is the sensor/reflector system (if availa- ble) aligned correctly? Online operating mode: The LED “Phase On” of the master fol- lows the trigger, but the read system remains functionless (no read proc- ess). • Does the software configuration match the application conditions (operating mode, etc.)? Check the corresponding parameters in the operating modes folder of the config- uration software. Serial online operating mode: The reader is not triggered (no read process). • Check whether "serial online" is activat- ed as the “online options” in the operat- ing modes folder of the configuration software. • Are the start and stop strings assigned correctly? • Is the serial trigger source connected correctly? Online operating mode and serial online operating mode: The reader does not respond correctly to the signal end. • Check the setting of parameter “Timeout for read cycle” in the operating modes folder of the configuration software. Description of error Diagnostics/remedy

Troubleshooting Date of issue 06/13/2005 91 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Reading: Target code cannot be read (no result is ever output) • Check the synchronization between the read impulse and the object to be read. • Is the scan line aligned correctly?·Place a barcode in the center of the scan line and start the test mode (can be selected as the operating mode in Genius™). If the problem persists: • Does the reading distance lie in the permissible limits (see reading fields)? • Is the tilt angle too large? • Is the angle of rotation under 10° (di- rect reflection)? • Select the CODE properties tab and activate various code types (except for pharmacode). Length = variable. • Is the code quality sufficient? • If the problem persists, carry out a test with the test sheet from Datalogic, en- closed with the product. Communication: The device does not transmit any data to the host. • Is the cable for the serial interface con- nected? • Is the wiring correct? • If using the primary RS232 or RS485 in- terface, is the earth reference connected with the correct signal ground SGND (al- so referred to as GND_ISO)? Bear in mind that this ground does not have any connection to the ground of the supply (GND). • If using a C-BOX 100, make sure that the RS485 termination switch is set to OFF. • Are the serial communication parame- ters set in the same way for the host and the device? Communication: No data appears on the terminal. • In the configuration software, activate parameter "Transmitted data" in the data communication settings for the primary/ secondary interface. Description of error Diagnostics/remedy

Troubleshooting Date of issue 06/13/2005 92 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Communication: The data transmitted to the host is faulty, incorrect or incomplete. • In the configuration program, select the folder DATA COMMUNICATION SET- TINGS/DATA FORMAT and check the entries for HEADER, TERMINATOR, SEPARATOR and FILL CHAR. • Also check the field CODE FIELD LENGTH for the code length. • Are the interface parameters set correct- ly? How do I find out the serial number of my device? • The serial number is located on a label above the connector of the reader. • The serial number can also be called via the configuration software. • The serial number is made up of 9 char- acters: 1 letter, 2 numbers, another letter and finally 5 numbers. Description of error Diagnostics/remedy

Technical data Date of issue 06/13/2005 93 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com 11 Technical data Remark 1: If not otherwise indicated, all specifications refer to an ambient temperature of 25 °C. Electrical features (see remark 1) Operating voltage Power consumption 15 to 30 V DC 15 W typically 20 W max. (including starting current) Communication interfaces Primary (galv. sepa- rate) Baud rate RS232 RS485 full-duplex RS485 half duplex 20 mA current loop (with INT-60 accesso- ries) 1200 to 115200 1200 to 115200 1200 to 115200 19200 Secondary RS232 1200 to 115200 Miscellaneous Lonworks Ethernet DeviceNet Profibus 1,25 Mb/s 10 or 100 Mb/s 125 or 250 Kb/s 12 Mb/s Inputs (NPN or PNP, with optocouplers External trigger 1 3 additional digital inputs Outputs (with optocouplers) 3 digit outputs programmable by software Figure system (see remark 1) Light receiver Wave length Safety class Laser control APD (avalanche photodiode) 630 to 680 nm Class 2 - EN60825-1; Class II - CDRH Safety system switches off laser when motor becomes slower Optical properties: Scan rate Maximum resolution Max. reading distance Max. reading width Max. depth of the field Deflection angle 600-1200 read processes/sec (see reading fields) (see reading fields) (see reading fields) (see reading fields) (see reading fields) Operator interface LCD display Key field Status LEDs 2 lines each with 16 characters 3 keys Power ON (red) Phase ON (yellow) TX Data (green)

Technical data Date of issue 06/13/2005 94 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com * Protection class IP50 for Ethernet conventional versions Software features Readable code families • Interleaved 2/5 • Code 39 standard • Codabar • EAN/UPC • Code 128 • EAN128 • Code 93 (standard and full ASCII set) Code selection Section and termination Operating modes Configuration types Parameter memory Up to 10 codes in a read cycle The transmitted messages can be adjusted via a section and a termination each with a length of 128 bytes. Online Automatic Test Software Non volatile internal Flash memory Ambient conditions Operating temperature Storage temperature Humidity Vibration exposure Shock exposure Protection class 0° to +40 °C (+32° to +104 °F) -20° to +70 °C (-4° to +158 °F) 90%, non-condensing IEC 68-2-6 test FC 1,5 mm; 10 to 55 Hz; 2 hrs in each axis IEC 68-2-27 test EA 30 G; 11 ms; 3 shocks in each axis IP64* Mechanical features Standard models Oscillating mirror models Dimensions in mm (inches) Mass 110 x 113 x 99 (4.33 x 4.45 x 3.9) 1,5 kg (3,3 lb) 113 x 180 x 104,5 (4.45 x 7.08 x 4.11) 2,0 kg (4,4 lb)

Glossary Date of issue 06/13/2005 95 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com 12 Glossary ACR™ 3 All the versions of the base assembly are equipped with the high-capacity ACR technology for the reconstruction of codes (ACR™ 3). The new, third generation of ACR™ improves the read and reconstruction capability in the case of damaged or heavily slanted barcodes significantly. Resolution The smallest sub-division of an element, which can be distinguished by a given reader or represented by an output device. Deflection The angular range across which the mirror can be adjusted in order to scan a surface to be read. Barcode A series of lines of varying width, which are separated by empty spaces and represent numeric or alphanumeric data in a machine readable form. Basically, a barcode symbol consists of a quiet area zone at the start, a start character, data or contents characters, check digit (if used), stop character and a subsequent quiet area zone. Within this basic structure, all the readable symbologies use their own format. Barcode label A label containing a barcode which can be attached to an article. Baud rate A unit for measuring the data transmission rate or the speed during the data exchange. CDRH (Center for Devices and Radiological Health) The Center for Devices and Radiological Health (an agency belonging to the American health authority FDA) is responsible for safety guidelines and radiation limit values of laser devices. VISOLUX devices meet the requirements stipulated by CDRH. CD SQUARE™ CD SQUARE™ provides useful information pertaining to the label position and the form of the object, which were determined in the read phase of the barcode. This innovative technology indicates the area which contains the code and measures the distance of the code to the reader.

Glossary Date of issue 06/13/2005 96 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Code alignment Different spacial arrangements of the code, which have an effect on the ability of the reader to read the code. The terms tilt angle, angle of rotation and tilt describe the angle variations of the code alignment in the X, Y and Z axes (Chapter 6.5). Changes to the code alignment have an effect on the impulse width and thus on the decoding of the code. The impulse width is defined as the change of the leading edge of a bar or spacing to the falling edge of a bar or spacing over time. The impulse width is also referred to as the transition. The rotation, tilt and visual angle have an effect on the impulse width of the code. Angle of rotation A rotation around the Y axis. This deviation from the horizontal and vertical can refer to individual characters, lines or whole coded objects (Chapter 6.5). EEPROM This is short for Electrically Erasable Programmable Read-Only Memory. A non volatile memory. Flash™ Flash™ is the new, dynamic focussing system, which is implemented in VB34. Flash™ is able to assume any reading position from the minimum position to the maximum position in less than 10 milliseconds. In typical applications with a reading distance of less than 1 meter, the reading position is reached in 4 milliseconds. The Flash™ technology makes it possible for the VB34 to cover a reading zone of more than 2 meters. Half duplex Transmission of data in only one transmission direction at a given point in time. Host A computer, which operates terminals in a network and provides services such as network management, database access, special programs, control programs and programming languages. Tilt angle A rotation around the Z axis. Serves to describe the position of a barcode in relation to the laser scanning line (Chapter 6.5). Laser diode with visible wave length A light source used in readers to illuminate the barcode symbol. It produces a red light in an area visible to the human eye between 630 and 680 nm.

Glossary Date of issue 06/13/2005 97 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com LED (light emitting diode, also referred to as luminescence diode) A semiconductor-based light source with a low energy requirement, which emits light in the visible or in the infrared area continuously or in impulse form to show whether voltage exists. It is frequently used for display purposes. Its power consumption is less than that of an electric light bulb, but above that of liquid crystal displays (LCD). If the service conditions are adhered to, the LEDs have an extremely long life. Reader A device which reads printed patterns (barcodes) and which either transmits the data in an unevaluated state to a decoder or decodes the data and transmits this data to a host system. Multidrop lead A communication path to which several partners can be connected. Also refer to RS485. Tilt angle The rotation of the code in the X axis. S. Section (Chapter 6.5). PackTrack™ PackTrack™ is a patented packet tracking system, which improves the read functionality in omnidirectional stations. PackTrack™ manages 6-page read systems, where it is not possible to recognize the actual position of the code on the packet. External accessories which are indispensable in traditional tracking systems are thus unnecessary. Parameters A value for specific attributes, which you specify in a program. Generally, parameters are set in order to configure the device to a certain operating behavior. Position The position of the reader or the light source relative to the target of a receiver element. Protocol A collection of formal conventions pertaining to the formatting and time-specific course of messages and their exchange between two communication partners. RS232 An interface standard for the serial, binary data exchange between a DTE (data terminal equipment) and a DCE (data communications equipment), that is, between two partners. RS485 An interface standard for the serial data exchange between several transmitters and receivers via a symmetrical transmission system with several partners, such as via a Multidrop lead.

Glossary Date of issue 06/13/2005 98 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com Interface A device connection that can be used externally with standardized electrical characteristic values, signal characteristics and meanings of the exchanged signals. Serial interface An I/O interface for connecting the reader to a computer, often can be recognized by a 9 or 25-pin connector. Signal An impulse or a variable electrical size (e.g. a voltage or a current), whose changes express a piece of information. Step-a-Head™ Step-a-Head™ makes it possible to turn the head of the reader and decoder base assembly independently from one another. A result of the Step-a-Head™ technology is that the VB34 can always be installed in the ideal position. In this instance, it is possible to change the alignment of the connector plugs, while the laser window retains its original position. Symbol A combination of characters including start and stop as well as check sum digits according to requirement, which together form a machine readable barcode. Trigger signal A signal, which generally comes from a light barrier or a proximity switch, informing the reader that there is an object in its reading field. UPC An abbreviation for Universal Product Code, the standard barcode type for retail packaging in the USA. Full-duplex Simultaneous and independent exchange of data in both transmission directions.