Sitech GCS900 Field Reference Manuals

TRAINING CHECKLIST CUSTOMER COPY Training Acknowledgement: Customer Signature Date SITECH Representative Date System: GCS900 Scraper Version: 13.1 Training Checklist Page # □ CB460 Control Box Layout 3 □ Scraper Training Display Settings 4 □ Check Blade Wear 6 □ Load Design 7 □ Verify System Accuracy 8 □ Vertical Offset 9 □ Horizontal Offset 10 □ Vertical Guidance 12 □ Cut and Fill Site Map 13 □ Lane Guidance 14 □ Sensor Calibration 15 □ Connect to Wi-Fi 16 □ TCC Settings 17 □ Configure Remote Assistant 18 □ Wireless Data Sync 19 □ Start Remote Assistant 20 □ Connect to IBSS Base 21

TRAINING CHECKLIST SITECH COPY Training Acknowledgement: Customer Signature Date SITECH Representative Date System: GCS900 Scraper Version: 13.1 Training Checklist Page # □ CB460 Control Box Layout 3 □ Scraper Training Display Settings 4 □ Check Blade Wear 6 □ Load Design 7 □ Verify System Accuracy 8 □ Vertical Offset 9 □ Horizontal Offset 10 □ Vertical Guidance 12 □ Cut and Fill Site Map 13 □ Lane Guidance 14 □ Sensor Calibration 15 □ Connect to Wi-Fi 16 □ TCC Settings 17 □ Configure Remote Assistant 18 □ Wireless Data Sync 19 □ Start Remote Assistant 20 □ Connect to IBSS Base 21

SITECH TECHNOLOGY DEALER Table of Content GCS900 Scraper Version: 13.1 Field Reference Guide Page # CB460 Control Box Layout 3 Scraper Training Display Settings 4 Check Blade Wear 6 Load Design 7 Verify System Accuracy 8 Vertical Offset 9 Horizontal Offset 10 Vertical Guidance 12 Cut and Fill Site Map 13 Lane Guidance 14 Sensor Calibration 15 Connect to Wi-Fi 16 TCC Settings 17 Configure Remote Assistant 18 Wireless Data Sync 19 Start Remote Assistant 20 Connect to IBSS Base 21

SITECH TECHNOLOGY DEALER Power Menu USB Port Enter Next Key Escape / Go Back Cut / Fill Right Function Keys (F1-F6) Zoom In - Out Cut / Fill Left Horizontal Guidance Page 3

SITECH TECHNOLOGY DEALER GCS900 Scraper Training Display Settings Version: 13.1 The Control Box must be in Manager’s Mode 1. Press “Menu” 2. Select “GNSS Accuracy” and Press “OK” 3. Press and Hold “F6 ” and Press “F2” Medium Mode 4. Change “GPS Horizontal error limit:” to “0.30ft or 0.090m” and Press “Next” 5. Change “GPS Vertical error limit:” to “0.30ft or 0.090m” and Press “OK” Twice 6. Select “Guidance Method” and Press “OK” 7. Use Arrow to change Adjust cut to avoid overcut: to “NO” and Press “OK” 8. Select “Increment Switch Adjustment” and Press “OK” 9. Change Vertical offset increment: “0.00” and Press “OK” 10. Select “Text Items” and Press “OK” 11. Press “F1” and Uncheck each Item checked 12. Press “F1” to select “Cut/Fill Left”, “Offline (3D)” and “Cut/Fill Right” (select in order) 13. Press “F3” Cross-Section 14. Press “F1” and Uncheck each Item checked 15. Press “F1” to select “Cut/Fill Left”, “Offline (3D)” and “Cut/Fill Right” (select in order) 16. Press “F4” Profile View 17. Press “F1” and Uncheck each Item checked 18. Press “F1” to select “Cut/Fill Left”, “Offline (3D)” and “Cut/Fill Right” (select in order) 19. Press “F5” Text View 1 20. Press “F1” and Uncheck each Item checked Page 4

to select “Design Elev.(3D)”, “Design XSlope (3D)”, “Mainfall (3D)”, “Satellites (3D)” and ”V. GNSS Err (3D)” (select in order) 22. Press “F6” Text View 2 23. Press “F1” and Uncheck each Item checked 24. Press “F1” to select “Northing (3D)”, “Easting (3D)”, “Elevation (3D)”, “Mainfall” and “Offline (3D)” (select in order) 25. Press “OK” 26. Select “Save Settings” and Press “OK” 27. Select “Display Settings” and Press “OK” 28. Enter Operator’s Name such as “Joe G” and Press “OK” 29. Press “ESC” twice to return to operating screen Page 5

SITECH TECHNOLOGY DEALER GCS900 Check Blade Wear Version: 13.1 1. Press “Menu” 2. Select “Blade Wear” and Press “OK” 3. Measure from Center of Cutting Edge Bolts to Bottom of Blade 4. Do not use Bolt at Blade Tip 5. Enter Distance and Press “OK” 6. Press “ESC” to return to operating screen Page 6

SITECH TECHNOLOGY DEALER GCS900 Load Design Version: 13.1 1. Press “Menu” 2. Select “Select Design” and Press “OK” 3. Use Arrows to highlight Design and Press “OK” 4. Press “ESC” to return to the operating screen Page 7

SITECH TECHNOLOGY DEALER GCS900 Verify System Accuracy Version: 13.1 Verify the system accuracy at the start of each work day using a Permanent Bench Point 1. Move machine to Bench Point with the Blade low to the ground 2. Position Blade Tip over Bench Point 3. Press “Next” until Text Screen 2 is displayed 4. Verify correct Blade Tip is selected Press “F1” to change Blade Tip 5. Verify Northing, Easting and Elevation are correct (add distance above Bench Point) 6. See Supervisor if Northing and Easting do not match 7. See Supervisor if Elevation does not match and Press “Next” Page 8

SITECH TECHNOLOGY DEALER GCS900 Vertical Offset Version: 13.1 1. Press “F4” to enter Horizontal and Vertical Offset 2. Press “F6” until Vertical Offset is displayed at the top left of screen 3. Enter Vertical Offset and Press “F2” to select above or below Design 4. Press “OK” to return to operating screen 5. Vertical Offset is displayed at the bottom of the screen Page 9

SITECH TECHNOLOGY DEALER GCS900 Horizontal Offset Version: 13.1 1. Press “F4” to enter Horizontal and Vertical Offset 2. Press “F6” until Horizontal Offset is displayed at the top left of screen 3. Press “F1” Alignment: 4. Use Arrows to Select [Plan Line] if list is displayed and Press “OK” 5. Use Arrows to Select Line Offset and Press “F1” Select Page 10

7. Press “F2” Select Offset to be Left or Right of the line (-3.00 is Left) 8. Press “OK” to return to operating screen 9. Horizontal Offset is highlighted in red 10. Press “F1” to change Blade Left or Right Page 11

SITECH TECHNOLOGY DEALER GCS900 Vertical Guidance Version: 13.1 1. Press “Menu” 2. Press “Guidance Method” and Press “OK” 3. Change Adjust cut to avoid overcut: to “NO” 4. Press “F1” for Change Method 5. Select Method from list and Press “OK” 6. Press “OK” to accept change 7. Press “ESC” to return to operating screen 1) One Point Center is the default setting used for long or wide surfaces. It also allows for shaping crowns by holding the slope past the crown- point. One Point Focus is used for narrow surfaces such as shoulders or slopes. Page 12

SITECH TECHNOLOGY DEALER GCS900 Cut and Fill Site Map Version: 13.1 1. Press “Menu” and select “Mapping/Recording Settings” Press “OK” 2. Change “Mapping for the main screen views” to “Yes” scroll down list 3. Change “Blade tip mapping” to “Automatics on” and Press “OK” 4. Select “Main Screen views” and Press “OK” 5. Under Active views select Cut/Fill “Yes” 6. Under Main Screen Softkeys select Softkey 5 “Mapping On/Off/Auto” and Press “OK” 7. Press “Esc” to Main Screen 8. Press “F5” until Mapping only in Automatic is displayed 9. Press “Next” until Plan View with Cut/Fill Scale is displayed Page 13

SITECH TECHNOLOGY DEALER GCS900 Lane Guidance Version: 13.1 1. Move Blade Tip with Focus over Lane to be Extended 2. Press “F3” for Lane Guidance 3. “F3” turns Lane Guidance Off and ON Page 14

SITECH TECHNOLOGY DEALER GCS900 Dozer Sensor Calibration Version: 13.1 1. Press “Menu” 2. Select “Calibrate Sensors” and Press “OK” 3. Select “Blade slope sensor (turn around) and Press “OK” 4. Following instructions 5. Press “F6” Finish 6. Press “ESC” twice to return to operating screen Page 15

SITECH TECHNOLOGY DEALER 16 April 2015 Connect to WiFi GCS900 Version: 13.1 1. Press “Menu” 2. Press “F2” Installation 3. Select “Connectivity Settings” then press “OK” 4. Select “Wi-Fi Network” then press “OK” 5. Press “F1” New 6. Select the Wi-Fi you wish to connect to press “OK” 7. Enter “Pass Phrase” 8. Press “F6” 9. Press “F6” Finish 10. Select the Wi-Fi to connect to Press “OK” 11. Press 2 times to return to main menu Page 16

SITECH TECHNOLOGY DEALER TCC Settings GCS900 Version: 13.1 1. Press “Menu” 2. Press “F2” Installation 3. Select “Connectivity Settings” then press “OK” 4. Select “Connected Community Settings” then press “OK” 5. Enter “Device Password” then press “Next” 6. Enter “Organization” then press “Next” 7. “Filespace and Work Group Folder” should be left to default 8. Press “OK” 9. Press 2 times to return to them main screen Page 17

SITECH TECHNOLOGY DEALER Configure Remote Assistant GCS900 Version: 13.1 1. Press “Menu” 2. Press “F2” Installation 3. Select “Connectivity Settings” then press “OK” 4. Select “Remote Assistant Configuration” then press “OK” 5. Enter “Support Number” 6. Press “F1” Force Upgrade 7. Press “OK” 8. Press 2 times to return to main screen Page 18

SITECH TECHNOLOGY DEALER Wireless Data Sync GCS900 Version: 13.1 1. Press “Menu” 2. Press “F2” Installation 3. Select “Connectivity Settings” then press “OK” 4. Select “Wireless Data Sync” then press “OK” 5. Press “F1” Start 6. When synchronization is complete Press “ESC” 3 times to operating screen Page 19

SITECH TECHNOLOGY DEALER Start Remote Assistant GCS900 Version: 13.1 1. Press “Menu” 2. Select “Remote Assistant” then press “OK” 3. Press “F1” Start 4. Once icon appears at the bottom of the screen the machine is connected 5. Press “ESC” 2 times to return to them main screen Page 20

SITECH TECHNOLOGY DEALER Connect to IBSS Base Station GCS900 Version: 13.1 The Control Box must be in Manager’s Mode 1. Press “Menu” 2. Press “F2” Installation 3. Select “Connectivity Settings” then press “OK” 4. Select “GNSS Base Configuration” then press “OK” 5. Select “IBSS-Remote Base” 6. Press “F1” Create New 7. Device Password and Organization should be populated if not see (TCC Settings Sheet) 8. Press “F6” 9. Select the Base from list and Press “F6” 10. Review IBSS Base Name and Press “F6” Finish 11. Select “IBSS - Remote Base” 12. Use left or right arrow keys to select correct base name and Press “OK” 13. Press 2 times to return to operating screen Page 21

www.sitechrockymtn.com (866) 903-2335 Service Center Locations: SITECH Rocky Mountain 2420 Uravan Street Aurora Co 80011