SOARNEX EWC-100 Quick Installation Manual

無線控制器 EWC-100 & EWC-100-62W EWC-100 & EWC-100-62W 系列 Quick Installation Guide 快速安裝指南 Rev. 1.0 Aug. 2017

Open the shipping carton and carefully unpack its contents. The carton should contain the following items. 1. EWC-100 series device x 1 2. DC Power adapter (w/ AC power cord): Power adapter (AC input:100-240v/0.5A, 50/60Hz, DC output: 12V/1A) for EWC-100 Power adapter (AC input: 100-240v/1.2A, 50/60Hz, DC output: 54V/1.67A) for EWC-100-62W 3. Rack mount kit x 1 4. Rubber Footpads x 4 5. Quick Installation Guide QR cod card x 1 ♦ Install the EWC device in a suitable temperature / humidity environment. ♦ The power outlet should be within 1.82 meters (6 feet) of the EWC device. ♦ Make sure that there is proper heat dissipation and adequate ventilation around the EWC device. ♦ Do not place any heavy objects above the EWC device. ♦ Users can check more technical specifications from http://www.soarnex.com if necessary. ! NOTE:

Power on Blinking System boot up Off Light off Power off USB Green Solid light When USB flash disk plug in Off Light off No USB flash disk plug in LAN (EWC-100) Green Solid light The port is transmitting or receiving data Off Light off No link Upper LED 1-5 (LAN) (EWC-100-62W) Green Blinking The port is transmitting or receiving data Off Light off No link The LEDs of the switch are located on the front panel. POWER / SYSTEM LAN EWC-100 1 2 3 4 5 POE MAX EWC-100-62W

The PoE port has supplied power normally Off Light off There is no PoE power device (PD) connection PoE Max (EWC-100-62W) Amber Solid light When the total PoE output power achieve Guard Band Off Light off System still have power for new PD Please check the detailed specification from http://www.soarnex.com if necessary.

rized appropriation. For firmware upgrade, backup/ restore configurati- on functions. EWC-100DC power socket accepts unput power 12V/1A. EWC-100-62W DC power socket accepts unput power 54/1.67A. On/ Off Power switch (for EWC-100)- Push the controller On/ Off push button to turn your controller “On” (Inner position) or “Off” (Outer position). Reset button- Press and hold this button for 15 seconds and release to reset the controller to factory defaults. The ports LEDs will trun off to indicate that the reset was initiated. USB DC IN DC IN RESET 1 2 3 4 5 RESET USB DC IN 1 2 3 4 5 RESET USB DC IN

to dissipate heat. • Do not block these openings, and leave at least 10cm to make sure that the environment is well ventilated.

the bottom of the EWC device. 2. Place the EWC device on a flat desk or shelf. 5. Plug the power cord into the power socket of the EWC device. 3. Attach the mounting brackets on the both sides of the EWC device and secure them with the screws. 4. Then, mount the EWC device to a rack with the screws. 1 2 3 4 5 POWER MAX EP100-05-31 POWER / SYSTEM LAN EWC-100 1 2 3 4 5 POWER MAX EP100-05-31 POWER / SYSTEM LAN EWC-100 1 2 3 4 5 POWER MAX EP100-05-31 POWER / SYSTEM LAN EWC-100

device and the surrounding objects. 7. Connect your wireless access points. RADIUS DHCP WAN EWC-100-62W EWC-100 PoE Switch Access Point Access Point LAN w/ DHCP Server w/ DHCP Server LAN

shown as below: • Please make sure the computer MUST be set on the same IP Subnet (same as the IP address of tyhe EWC device) • For example, the default IP address of the EWC device is 192.168.1.100 with subnet mask 255.255.255.0, then the computer should be set 192.168.1x (where x is a number between 1-254, expect 100)with subnet mask 255.255.255.0.

Open your web browser and enter http://192.168.1.100 (the factory-default IP address) to access the WEB platform. Default User Name and Password of the EWC device are “admin”. Note,You can configure the EWC device by entering the User Name/Password and IP Address via WEB platform. 2. Recovering Back to Factory Default Configuration If you’ve forgotten the User Name or Password or IP Address which has been changed, and then you can reset it to factory default settings through console port. After the EWC device has rebooted, you can login the EWC device via web browser and enter IP Address http://192.168.1.100 with the default User Name/Pass- word (the factory-default is “admin”).

FCC Warning CE Mark Warning Declaration This is a Class A product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures. This product is here with confirmed to comply with Directive of 2004/108/EC and 2006/95/EC. I here by declare that the products and devices mentioned above are consistent with the standards and provisions of the guidelines. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this user’s guide, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interfence at his own expense. Change or modifications not expressly approved by the party responsible for compliance could void the user‘s authoruty to operate the equirments. 1. EP100-05-31 and EP100-08-31: Up to 31 Watts for port1~port4 and the maximum total PoE power budget of 31 Watts. 2. EP100-08-62: Up to 62 Watts for port1-port4 and the maximum total PoE power budget of 62 Watts. 3. EP100-08-31: 4 x Gigabit PoE RJ-45 ports(port1~4, provides up to 15.4 watts) and 4 x Gigabit RJ-45 ports. 4.EP100-08-31: 4 x Gigabit PoE/PoE+ RJ-45 ports(up to 30 watts) and 4 x Gigabit RJ-45 ports. CAUTION