Slinex SL-07M Operation & User’s Manual

DESIGN DIRECT SERIES SL-07M 7” video door phone Thank you for the choice of our equipment User manual

DESIGN DIRECT SERIES 1 Rev. 2.0 2 Attention! As a result of continuous upgrades and functionality improvements, technical characteristics of the device can be changed without any preliminary declaration. This manual can contain some inaccuracy or misprint. The owner reserves the right to make corrections to the information described in the user manual and device package. The last revision of this manual is available on www.slinex.com Safety instructions Read and keep that manual. The device installation process should be carried out by the qulifed specialists. Use the device from the –10 ˚C to +55 ˚C, always keep it within that temperature range. Installation surface should be free from vibration and impact infuence. Keep this device far from open sources of heat, such as radiators, heaters, and ovens. The device can be installed near other electronic equipment in case if the temperature of the environment does not exceed previously mentioned range. The device should be protected from the direct infuence of the natural phenomena, such as direct sunlight, rain or snow. Don’t use aggressive or abradant detergent for the device surface cleaning. Use soft wet cloth or tissue to remove strong dirt. Don’t overpower outlets. It can cause fre or electric shock. Nature protection Don’t throw away the device with other industrial or nutritive trash if you see that symbol. Some regions have separation and recycling systems for the electronic equipment. Connect with local authorities to receive information about recycling of electronic equipment for your region. Rights and limitation of liability All rights reserved. Any part of that document can not be published in any form, translated into other languages or reproduced in any way including electronic or mechanical. Document recording and copying is strictly denied without owner permission. Table of contents 1. Package.............................................................................................................................................................................................3 2. Specifcation....................................................................................................................................................................................3 3. Description......................................................................................................................................................................................4 4. Installation.......................................................................................................................................................................................5 4.1 Cable requirements.....................................................................................................................................................5 4.2 Schematic diagrams...................................................................................................................................................6 4.3 Unit mount.....................................................................................................................................................................8 5. Operation.........................................................................................................................................................................................9 5.1 Incoming call.................................................................................................................................................................9 5.2 Door panel and camera image view...................................................................................................................10 5.3 Incoming call redirection.......................................................................................................................................11 5.4 Intercom.......................................................................................................................................................................12 6. Monitor settings..........................................................................................................................................................................12 6.1 Main menu...................................................................................................................................................................12 6.2 System settings..........................................................................................................................................................13 6.3 Melody and volume settings................................................................................................................................15 6.4 Working mode settings...........................................................................................................................................16 6.5 Alarm settings.............................................................................................................................................................17 6.6 Display settings..........................................................................................................................................................20 6.7 Snapshots and records playback.........................................................................................................................21 7. Manual recording........................................................................................................................................................................23 8. External sensors motion detection recording..................................................................................................................23 9. Limited Warranty.........................................................................................................................................................................24 !

DESIGN DIRECT SERIES 3 4 Screen Resolution Video system Audio type Call time Internal memory Memory extension slot Standby mode power consumption Working mode power consumption Power supply Mounting type Size Working temperature 7”, color TFT 800×480 pixels PAL/NTSC Half duplex 120 seconds 100 snapshots microSD, up to 32 GB 3 W 7 W Built-in power supply, ~100–240 V Surface mount 230×165×22 mm −10...+55 ˚C 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Power LED. Active when the power is on. First door panel LED. Active when the frst door panel is on. Second door panel LED. Active when the second door panel is on. Display «Up» button – increase talking volume, system settings menu cursor movement, parameter increase inside settings menu «Down» button – decrease talking volume, system settings menu cursor movement, parameter decrease inside settings menu Speaker (on the back side of the monitor) «Settings/Record» button: • push this button in standby mode to enter system settings menu; • push this button on chosen parameter inside system settings menu to change its value. Then push it again to confirm the changes; • push this button in monitoring or talking mode, to record snapshot or video from the door panel or camera «Intercom» button – call another monitor or incoming call redirection «Monitor» button – door panel or camera image monitoring «Answer» button – incoming call answer and start talking with the visitor «Unlock» button – door unlocking MicroSD memory card slot (on the side of the monitor) «Hang Up» – stop conversation with the visitor / current system settings menu exit Microphone 1. Package SL-07M door monitor − 1 pc. Wall mounting bracket − 1 pc. Connection wires − 7 pcs. Mounting screws and nuts − 1 pkg. User manual − 1 pc. 2. Specifcation 5 1 2 3 4 6 7 8 9 10 11 12 13 14 15 3. Description 165 mm 230 mm 22 mm

DESIGN DIRECT SERIES 5 6 4.2 Schematic diagrams Diagram 1. SL-07M door panels, cameras, locks and TV connection. Power Audio GND Video Not used Signal GND Video Lock TV Door panel 1 Door panel 2 SL-07M (Master) Lock power supply Lock Lock power supply Video GND Door 1 Door 2 CCTV 1 CCTV 2 Input Output Power TV out GND +13,5 V * Camera power suppply Camera power suppply Motion sensor Motion sensor CCTV 2 Video GND GND +12 V CCTV 1 4. Installation 4.1 Cable requirements Disconnect all power cables before device installation. This device can be connected with such cable types depends on the distance between door monitor and door panel: а) Use 4-wire cable with such parameters: • distance up to 25 meters use a cable with 0,22 mm2 square of one wire; • distance 25 to 50 meters use a cable with 0,41 mm2 square of one wire; • distance 50 to 100 meters use a cable with 0,75 mm2 square of one wire. b) If the distance between door monitor and door panel is between 80 and 100 meters then use a 3-wire cable with 0,75 mm2 square of one wire and RG-59 or RG-6 coaxial cable for the video signal. c) Shielded or non-shielded twisted pair (not recommended): • distance up to 25 meters non-shielded twisted pair can be used; • distance 25 to 50 meters shielded twisted pair should be used. Power Audio Ground Video Power Audio Ground Video Power Audio Ground Video Power Audio Ground Video Power Audio Ground Video Power Audio Ground Video 0 - 50 m Shield Shield 50 - 80 m 80-100 m RG-59 or RG-6 Video GND GND +12 V Not used Signal GND Video Power Audio GND Video 0 - 25 m 25 - 50 m Power Audio Ground Video Power Audio Ground Video Power Audio Ground Video Power Audio Ground Video Shield Shield

DESIGN DIRECT SERIES 7 8 Diagram 2. SL-07M system connection. SL-07M (Master) Door 1 Door 2 CCTV 1 CCTV 2 Input Output Power TV out SL-07M (Slave) Notes: * Use «Power» plug on the monitor to connect external power supply +13,5 V. While use external power supply please keep main power cord ~100-240 V disconnected from the outlet, otherwise it can damage monitor circuits. ** Door panels, cameras, power supplys, locks and motion sensors described on the schemes are optional devices and aren’t included into monitors kit. Audio GND Data Video Audio GND Data Video Audio GND Data Video Audio GND Data Video Audio GND Data Video SL-07M (Slave) SL-07M (Slave) 4.3 Unit mount 1) Take the surface mount bracket from the kit and situate it 150-160 cm from the foor line. 2) Mark and drill four halls in the wall. 3) Take four nuts from the kit and hammer them into the drilled halls. 4) Fix surface mount bracket on the wall by four screws from the kit. 5) Connect all communication wires and fx the monitor on the surface mount bracket.

DESIGN DIRECT SERIES 9 10 5.2 Door panel and camera image view Standby mode Monitor will display the image from the frst door panel (monitoring time – 60 seconds) Monitor will display the image from the second door panel (monitoring time – 60 seconds) Press «Monitor» button on the monitor 5. Operation 5.1 Incoming call Standby mode Standby mode Melody is ringing on the monitor and door panel, image from the door panel appears on the monitor screen Visitor presses call button on the frst door panel Visitor presses call button on the second door panel Press «Answer» button to start conversation with the visitor Melody stops ringing and conversation starts, talking time is 120 seconds Press «Hang up» button to stop conversation or incoming call Press «Unlock» button to open lock connected to the current door panel, relay built into the panel will open the lock Notes: 1) Monitor will be automatically switched into standby mode if the user doesn’t answer incoming call during 60 seconds; 2) Image and sound from the door panel will be active during 20 seconds after the moment user presses button. It let the user know if the visitor passed through the door. 20 seconds 20 seconds Standby mode Press «Monitor» button on the monitor again Press «Monitor» button on the monitor again Press «Monitor» button on the monitor again Press «Monitor» button on the monitor again Monitor will display the image from the frst CCTV camera (monitoring time is unlimited) Monitor will display the image from the second CCTV camera (monitoring time is unlimited) Press «Hang up» button to stop monitoring or conversation Press «Answer» button to start conversation with the visitor Press «Unlock» button to open lock connected to the current door panel, relay built into the panel will open the lock

DESIGN DIRECT SERIES 11 12 5.4 Intercom Two monitors connected into one system are used. Melody starts ringing Standby mode 5.3 Incoming call redirection Two monitors connected into one system are used. Notes: 1) If only one door panel connected to the monitor then you can escape monitoring mode by pressing «Monitor» button one more time. (all other sources of video signal should be disabled in the monitor settings). 2) If several monitors connected into one system, the user can view the image from door panels and cameras on any monitor inside this system. The image will be transferred from the «Master» monitor door panels and cameras to the «Slave» monitors. 3) If someone press call button on the door panel while monitoring is active then the image from this door panel appears on the monitor screen and call melody starts. Press «Answer» button to start conversation. Note: If incoming call was successfully redirected to the other monitor and other user answered the call then current monitor will enter standby mode. Melody starts ringing on the other monitor inside the system and visitor image appears on the monitor screen Conversation with the visitor on the other monitor begins Incoming call from the door panel and the user starts conversation Press «Intercom» button to start call redirection 20 seconds Note: If someone press call button on the door panel while intercom is active then the image from this door panel appears on the monitor screen and call melody starts. Press «Answer» button to start conversation with the visitor. 6. Monitor settings 6.1 Main menu Press button in standby mode to enter main menu monitor settings. Use or buttons to move through the settings. Press button again to enter current setting sub menu. Then press or button to change current parameter value and approve the setting by pressing button. Press «Return» button on the screen or press button on the keyboard to exit from the current settings menu. Press «Answer» button on the other monitor to start conversation with the visitor Standby mode Press «Unlock» button to open lock connected to the current door panel, relay built into the panel will open the lock Press «Hang up» button to stop conversation or incoming call Standby mode Press «Intercom» button to start intercom conversation Conversation with the other monitor starts Press «Answer» button on the other monitor to start conversation Press «Hang up» button to stop conversation

DESIGN DIRECT SERIES 13 14 6.2 System settings Press «System» icon in the main menu to enter system settings of the monitor: Release date − date of software release. Format SD − micro SD card formatting. Please format microSD card before use it. Recommended to use microSD cards of the 6-th class and above. Format flash − internal memory formatting. Backup pictures− copy files from the internal memory to microSD card. Update −firmware updating of the monitor (place updating files in the root folder of microSD). Reboot − system reboot. Following parameters are available in the «System» menu: Language − the language of the settings menu. Time − date and time settings. Time display − date and time screensaver display in stndby mode (Off, 1, 3, 5, 10 min.). Information: Software version − current software version of the monitor. Information Return Time Language System Ring Alarm Color Files Mode Main menu Language System Main menu Time System Main menu System Main menu Return English DD-MM-YY 08-07-2016 16:17 Time display: 10 min Return Return

DESIGN DIRECT SERIES 15 16 6.3 Melody and volume settings Press «Ring» icon in the main menu to enter melody and volume settings. Following parameters are available in the «Ring» menu: Ring select − choose the melody for every door panel. Ring volume − choose volume level (from 00 to 09) depending on the time of a day and also ringing time of the melody (10-45 seconds). Silence mode − incoming call melody and keyboard muting, «On» or «Of». 6.4 Working mode settings Press «Mode» icon in the main menu to enter working mode settings. Following parameters are available in the «Mode» menu: Mode − choose «Master» if you use one monitor in the system or if it’s the monitor which all the door panels and CCTV cameras are connected to. Choose «Slave» if there is more than one monitor in the system and no door panels or CCTV cameras connected to this monitor. Door 2 status − «On» or «Of», include or exclude second door panel from the monitoring list. Software version: 1.1.3.2 Release date: 2016-07-08 Format SD Format flash Backup pictures Update Reboot Return Ring Volume Ring Select Return Door 1 01 Door 2 02 Return Ring vol 1 08 : 00 ~ 18 : 00 08 30 sec Ring vol 2 18 : 00 ~ 23 : 00 04 30 sec Ring vol 3 23 : 00 ~ 08 : 00 01 30 sec Silence mode: Off Return System Main menu Information Main menu Ring Ring select Main menu Ring Ring volume Main menu Ring

DESIGN DIRECT SERIES 17 18 6.5 Alarm settings Press «Alarm» icon in the main menu to enter alarm settings. Following parameters are available in the «Alarm» menu: CAM alarm – additional cameras alarm settings; Motion detect – software motion detection. CAM alarm includes next sub menu: CAM1 sensor type: «NO», motion sensor with normally disconnected contacts are used; «NC», motion sensor with normally connected contacts are used; «Of», motion sensor doesn’t used. CAM2 sensor type: «NO», motion sensor with normaly disconnected contacts are used; «NC», motion sensor with normaly connected contacts are used; «Of», motion sensor doesn’t used. CAM1 − «On» or «Of», include or exclude first CCTV camera from the monitoring list. CAM2 − «On» or «Of», include or exclude second CCTV camera from the monitoring list. CAM1 ring time − alarm melody ringing time activated by CAM1 motion sensor, from 00 to 30 seconds. CAM2 ring time − alarm melody ringing time activated by CAM2 motion sensor, from 00 to 30 seconds. Alarm record: «Snapshot» − save photo if motion detection has occurred; «Record» − save video if motion detection has occurred. Mode: Master Door 2 status: On Record mode: Snapshot Door 1 unlock time: 02 sec Door 2 unlock time: 03 sec Key backlight: On Keyboard sound: Off Return Record mode: «Snapshot» – take snapshot while incoming call or manually; «Record» – record video while incoming call or manually. Door 1 unlock time − Door 1 relay delay time, 2 –10 seconds. Door 2 unlock time − Door 2 relay delay time, 2 –10 seconds. Key backlight − «On» or «Of». Keyboard sound − «On» or «Of». Main menu Mode CAM1 sensor type: NO CAM2 sensor type: NO CAM1: On CAM2: On CAM1 ring time: 10 sec CAM2 ring time: 10 sec Alarm record: Record Return Main menu Alarm CAM alarm Main menu Alarm Motion detect Return CAM alarm

DESIGN DIRECT SERIES 19 20 6.6 Display settings Press «Color» icon in the main menu to enter display settings. Following parameters are available in the «Color» menu: Door1 − image settings for the frst door panel. Door2 − image settings for the second door panel. CAM1 − image settings for the frst CCTV camera. CAM2 − image settings for the second CCTV camera. Door1 Door2 CAM1 CAM2 Return Main menu Color Software motion detector can observe and detect motion without any external sensors using any camera image changes with the time. Camera power that is used for motion detection should be constantly on to let the monitor observe image changes and detect it. Motion detect includes next sub menu: Motion detect source: «Of» – software detector is of; «Door1» – motion detection on Door1; «Door2» – motion detection on Door2; «CAM1» – motion detection on CAM1; «CAM2» – motion detection on CAM2. Motion detect area − set image area which motion detection is performed. Store mode: «Snapshot» – save photo if software motion detection has occurred; «Record» – save video if software motion detection has occurred. Notifcation − «On» or «Of». Enable or disable sound alarm if software motion detection has occurred. Motion detect source: Door1 Motion detect area Store mode: Snapshot Notification: Off Return Main menu Alarm Motion detect Main menu Alarm Motion detect Motion detect area Return

DESIGN DIRECT SERIES 21 22 Every video source has its own image settings: Brightness – parameter range from 0 to 50, 25 used by default. Contrast – parameter range from 0 to 50, 25 used by default. Color – parameter range from 0 to 50, 25 used by default. Press «Record files» or «Snapshot files» icon to enter snapshots or records playback menu then choose the fle to play. Choose one of three operations: Play – current fle viewing; Delete current fle – current file deleting; Delete all fle – all fles deleting. Move the marker between fles by or button. While viewing press button to go back to the fles list. Door1 25 25 25 Return Main menu Color Door1 Door2 CAM1 CAM2 6.7 Snapshots and records playback Press «Files» icon in the main menu to enter snapshots and records playback. Following parameters are available in the «Files» menu: Record fles − records playback. Snapshot fles − snapshot fles playback Record files Snapshot files Record Files Main menu Files 0005 / 0005 12 : 10 : 35 31 - 08 - 2015 Record files Main menu Files Main menu Files 001 / 003 20150831 - 121033 0005 20150831 - 120548 0004 20150831 - 120234 0003 20150831 - 115828 0002 20150831 - 115630 0001 Play Delete current file Delete all file Return Return

DESIGN DIRECT SERIES 23 24 7. Manual recording User can take snapshots or record video during monitoring door panel or CCTV camera. Press button to start recording then press button again to stop recording. Depending from the setting «Record mode» (page 17) snapshots or video can be recorded. Note: Video can be recorded only if micro SD card installed into monitor slot. If microSD is absent then monitor will record snapshots using internal memory no metter what «Record mode» is set. 100 snapshots can be stored on internal memory. If the quantity exceeds 100 snapshots then older snapshots will be replaced by new one. 8. External sensors motion detection recording Camera 1 and Camera 2 has motion detection function by external motion sensor. When external sensor connects or disconnects its contacts (depending on «CAM1 sensor type» or «CAM2 sensor type» setting in «Alarm» → «CAM alarm» menu, page 17-18), recording starts on the door monitor. Video recording time is 120 seconds. Press button to stop recording manually. Use any external sensors that has normaly opened «NO» or normaly closed «NC» contacts. When the sensor is activated it connects (NO case) or disconnects (NC case) contacts which activates recording on the door monitor. +12 V Ground Ground Video Camera power supply Motion sensor CCTV camera Not used Signal Ground Video External motion sensor connection. 9. Limited warranty Manufacturer guarantees product normal functioning during the warranty period if the user keeps all safety instructions described in that manual. Warranty period is 12 months from the moment of the product purchasing (warranty period could be extended up to 24 months or more, depending on the local regulations). Warranty period allows user to make guarantee repair in cases when normal functioning of the product was violated by the fault of manufacturer and the user haven’t ofend transporting, installation and working conditions. This limited warranty does not cover any damage to the product that results from improper installation, accident, abuse, misuse, natural disaster, insufcient or excessive electrical supply, abnormal mechanical or environmental conditions, or any unauthorized disassembly, repair or modifcation. Warranty void in such cases: • the product was damaged by the fault of the customer; • the product wasn’t properly installed according reccomendations from the manual; • the sticker on the backside of the product was broken; • the product was not used for its intended function. This limited warranty covers only repair, replacement, refund or credit for defective products, as provided above. Manufacturer is not liable for, and does not cover under warranty, any damages or losses of any kind whatsoever resulting from loss of, damage to, or corruption of, content or data or any costs associated with determining the source of system problems or removing, servicing or installing products. This warranty excludes third party software, connected equipment or stored data. Manufacturer is therefore not liable for any losses or damage attributable to third party software, connected equipment or stored data. In the event a product has been discontinued, manufacturer shall either repair the product, ofer to replace it with a comparable product or provide a refund at the lesser of the purchase price or the product’s current value. Repaired or replacement products will continue to be covered by this limited warranty for the remainder of the original warranty term.