Remocon HCD900 Operation Manual

Operation manual HCD-900 Accessories HCD-900 Console 6Micro USD Duplicating & Updating Cable (Attached) AC/DC Power Adaptor(attached) 6P connector Duplicating Cable (Optional) Frequency Tuning Bar (Optional)

Caution: Do not put the duplicator on the metal surface while operating, and keep interference(mobile phone, router....) away while operating. 2. LCD screen displays Main Menu.(Fig. 2) Fig. 1 Fig.2 Remark: Press & to move highlight to desired mode and press Confirm. If you would like to return to MAIN MENU after entering, press Cancel . 3. Function instruction 3-1. Frequency Meter (Fig. 3) 3-1-1. Func.: Read transmitting frequency from remote controls. 3-1-2. Hold the remote control one hand near the Test Area of HCD900, and press any button of the remote control. The “Measuring” keeps flashing and "signal strength bar" changes while reading the frequency; Slightly move the position of the remote control until you get the longest signal bar to ensure you can get most correct frequency.(Fig. 4) Fig. 3 Fig. 4 REMOCON Version 3001.13 MAIN MENU Frequency Meter FixedCode Duplicate HoppingCode Duplicate REMOCON Read Back Code Checking Make Hopping Setting Frequency Meter 0.0Mhz MAIN MENU Frequency Meter FixedCode Duplicate HoppingCode Duplicate REMOCON Read Back Code Checking Make Hopping Setting Fn Confirm Cancel Test Area Frequency Meter Measuring 433.7Mhz 11111111111111111111 Power swith

frequency, you can change your Meter to low frequency Mode(LCD displays "LF" on screen, Fig.5) by pressing "Fn" and "Confirm" at the same time. Under Low frequency mode, it will only detect frequency under 600MHz. Fig. 5 3-2. Fixed Code Duplicate: No.1 to No. 5 are for frequency band 1, and No. 6 to No.10 are for frequency band 2(for dual frequency remotes). 3-2-1. Func.: Read and duplicate fixed code from original remote control into REMOCON remote control. It provides 10 channels for programming. (Fig. 6) 3-2-2. Places original transmitter near the Test Area of HCD900. Fig. 6 3-2-3. Press and holding 1st button of original remote control, LCD screen displays “Processing”. Release the button when you hear a beep. Now the frequency and type of remote of original remote is shown above the channels, and the code of the 1st button of original remote has been read successfully.(Fig. 7) 3-2-4. Repeat step 3-2-3. until all buttons of original remote control have been read by HCD900.(Fig. 8) [Note: for dual frequency remotes RMC-552, RMC-556 & RMC-558: channel 1 to 5 are for buttons 1 to 5 when the switch position is “Up”, and channels 6 to 10 are for buttons 1 to 5 when the switch position is “Down”; for RMC-558C: opposite to above] FixedCode Duplicate 1 2 3 4 5 6 7 8 9 10 10 key spaces remain Ready FixedCode Duplicate 433.9 B10 Type 1 2 3 4 5 6 7 8 9 10 1 9 key spaces remain Processing Ready FixedCode Duplicate 433.9 1 2 3 4 5 6 7 8 9 10 1 1 1 1 6 key spaces remain Ready Frequency Meter LF 0.0Mhz Fig. 7 Fig. 8

After all keys of 2 remotes with different frequencies has been read by HCD-900, press & to move highlight to channel 1 ~ 5 and channel 6 ~ 10 and to choose the right frequency bands on REMOCON remote by pressing & (Fig. 9) Fig. 9 3-2-6. Press Confirm to enter duplicating mode, the LCD displays as Fig. 10 3-2-7. Connects B or C type REMOCON remote control to HCD900 by using attached duplicating cable. Fig. 10 3-2-8. Press Confirm to program the code into REMOCON remote control. LCD displays duplication result as Programming Success or Programming Failure.(Fig. 11) Notice: if the original remote belongs to C type but you connect a B type REMOCON remote, the LCD screen will display "Please Use C Remote" and please connect a C type REMOCON remote and retry. Fig.11 3-3. Hopping Code Duplicate:(Fig. 12) 3-3-1. Func.: Read and duplicate hopping code from original remote controls into REMOCON remote controls. Fig. 12 Attention: Some brands of hopping code remote controls were required to input “seed code” before going to next step. To input “seed code”, please follow FixedCode Duplicate 433.9 1 2 3 4 5 6 7 8 9 10 1 1 1 1 6 key spaces remain Please Connect Remote FixedCode Duplicate 1 2 3 4 5 6 7 8 9 10 1 1 1 1 6 key spaces remain Programming success HoppingCode Duplicate 1 2 3 4 5 6 7 8 9 10 10 key spaces remain Please enter 1st code FixedCode Duplicate 433.9 1 2 3 4 5 6 7 8 9 10 1 1 1 1 2 2 2 2 6 key spaces remain Ready

a. Touch Fn & simultaneously. b. LCD displays “Receiving seed code”.(Fig. 13) c. You can probably find the seed code button on the rear of original remote control. It might be hidden in an eyelet. If so, you need a acicular object to poke it for transmitting the seed code. d. The LCD displays (Fig. 14) when the “seed code” was received. Fig. 13 Fig. 14 3-3-2. Place the original remote control near the Test Area of HCD900. 3-3-3. Press and holding 1st button of original remote control, LCD displays a serial number(Fig. 15). (Each remote control has its own series number). Fig. 15 3-3-4 Press and holding 1st button of original remote control again. The LCD displays as Fig. 16. It will create a new serial number automatically for the REMOCON remotes and you can also change it to whatever number you need. The number on the bottom right corner is the serial number of the original remote. Notice: Don't set up the same serial number with the original remote; Otherwise, you will have problem using 2 remotes at the same time. 3-3-5. Press Confirm , the LCD displays as Fig. 17. Now the 1st button has been stored successfully HoppingCode Duplicate 1 2 3 4 5 6 7 8 9 10 10 key spaces remain Receiving seed code HoppingCode Duplicate 1 2 3 4 5 6 7 8 9 10 10 key spaces remain HCS 10x 20x 30x Please enter 1st code HoppingCode Duplicate 433.9 1 2 3 4 5 6 7 8 9 10 10 key spaces remain HCS 10x 20x 30x 02 00024E68 7606A080 Please enter 2nd code HoppingCode Duplicate 433.9 1 2 3 4 5 6 7 8 9 10 10 key spaces remain Serial Number Setting 00242D3 BFT 00024E68 HoppingCode Duplicate 433.9 1 2 3 4 5 6 7 8 9 10 1 9 key spaces remain Please enter 1st code Fig. 16

remote control, LCD displays as (Fig. 18) 3-3-7. Repeat step 3-3-6. to store other buttons of original remote control. Fig. 18 3-3-8. If the frequency that HCD-900 detects(LCD displays on the upper left corner) is not correct, you can revise the frequency for one button or all buttons as below: 3-3-8-1. Move the highlight to the channel that you would like to revise the frequency, and then press Fn and at same time. (Fig. 19) Fig.19 3-3-8-2. Press and to move the "！" to different position above the frequency and press and to adjust the value of the frequency.(Fig. 20) Fig. 20 3-3-8-3. Move "！" to the last position and you can select to revise frequency for only one button(the channel where the highlight is) or all buttons.(Fig. 21) Fig. 21 3-3-8-4. Press Confirm then the revision of frequency is done. Attention: You can also revise the frequency by the same way in FixedCode Duplicate Mode. 3-3-9. Connect the H series or BHS/CHM/CHML new series REMOCON remote control to HCD900 by using attached duplicating cable. Notice: if the original rolling code remote uses new IC format that H3/BHS/CHM does not support, the LCD screen will display "Please Use CHMLRemote" and please connect a H4 HoppingCode Duplicate 433.9 1 2 3 4 5 6 7 8 9 10 1 1 8 key spaces remain Please enter 1st code HoppingCode Duplicate 433.9 1 2 3 4 5 6 7 8 9 10 1 1 8 key spaces remain ！ ALL 433.9 MHz HoppingCode Duplicate 433.9 1 2 3 4 5 6 7 8 9 10 1 1 8 key spaces remain ！ ALL 432.9 MHz HoppingCode Duplicate 433.9 1 2 3 4 5 6 7 8 9 10 1 1 8 key spaces remain ！ One 432.9 MHz

3-3-10. Press Confirm to program the code into REMOCON remote control. 3-3-11. LCD displays duplicating result as Programming Success or Programming Failure. (Fig. 22) 3-4. REMOCON Read Back (For Fixed Code remote) 3-4-1 Func.: To read the code from REMOCON remote control, and reduplicate the code into other REMOCON remote controls. 3-4-2. Be sure to connect REMOCON remote control(existing code) to HCD900 by using attached duplicating cable before entering “REMOCON Read Back” mode. (Fig. 23) 3-4-3. Move highlight to “REMOCON Read Back” mode, press Confirm to start reading. The LCD displays as Fig. 24. Fig. 24 3-4-4. Replace the remote control by a new REMOCON remote control and touch Confirm. LCD displays duplication result as Programming Success or Programming Failure. 3-5. Code Checking(Fig. 25) 3-5-1. Func.: There are 2 functions in this mode: First is to verify whether the fixed code duplication has been done successfully or not; Second is to identify your existing remote control is fixed code or hopping code. HoppingCode Duplicate 1 2 3 4 5 6 7 8 9 10 1 1 8 key spaces remain Programming success Please enter 1st code MAIN MENU Frequency Meter FixedCode Duplicate HoppingCode Duplicate REMOCON Read Back Code Checking Remote Report FixedCode Duplicate 1 2 3 4 5 6 7 8 9 10 1 1 1 1 6 key spaces remain Ready Code Checking Please Enter 1st Code Press cancel To Exit Fig. 23 Fig. 25 Fig. 22

been done successfully, press 1st button of original fixed code remote control till you hear a beep. 3-5-3 The LCD appears “Processing” and goes to Fig. 26. 3-5-4. Press 1st button of the duplicated remote, HCD900 starts to check the contrast, and then shows the similarity percentage.(Fig. 27) Fig. 27 3-5-5. Follow steps 3-5-2, 3-5-3 &3-5-4 to verify other buttons. Attention: The qualified duplication requires at least 90% similarity. 3-5-6. To identify whether the remote control is fixed code or hopping code, press 1st button of the remote control. (Fig. 25) 3-5-7. The LCD appears “Processing” and goes to Fig. 26. 3-5-8. Press the same button again. HCD900 starts to check the contrast, and then shows the similarity percentage.(Fig. 27) 3-5-9. Hopping code remote control will show 0.0 percent matched. 3-6. Make Hopping(for Hopping Code remote) 3-6-1. Func.: Create a duplicate remote without the existing of original rolling code remote control. (This function can only be used to create original remotes with HCSxxx IC format and original remotes without seed code, if you would like to create these 2 kinds of remotes, please use HCD-900line) 3-6-2. Press and to choose PAGE or 1 so that you can select brand "Page by page" or" brand by brand". (Fig. 28) 3-6-3. Press to enter the Reference Number Setting. Press and to set up the distributor code. (Only need to set up for certain brands) (Fig. 29) Code Checking Please Enter 2nd Code Press cancel To Exit Code Checking Please Enter 1st Code 99.2 Percent Matched Press cancel To Exit Make Hopping PAGE 1 NiceSmile Neo GiBiDi FADIN 00 Make Hopping FADIN 01 Fig. 26 Fig. 28 Fig. 29

Serial Number Setting. Press and to set up the serial number. (Fig. 30) Fig. 30 3-6-5. Press Confirm to ready to copy. (Fig. 31) Notice: If you would like copy to a CHM or CHML remote, please ensure to set up the frequency first by pressing Fn and simultaneously. Connect H series or BHS/CHM /CHML REMOCON remote control to HCD-900 by using attached duplicating cable. 3-6-6. Press Confirm to program the code into REMOCON remote control. LCD displays duplication result as Programming Success or Programming Failure.(Fig. 32) Fig. 32 3-7. Setting 3-7-1. Func.: See relative information or change the setting. 3-7-2. You can see the version number and production serial number of your HCD-900 after entering setting mode.(Fig. 33) . Fig. 33 3-7-3. Press and you will enter the setting page as Fig. 34. Press and to select the project and press to change the parameter Fig. 34 Make Hopping Serial Number Setting 0000001 FADIN 01 HoppingCode Duplicate 1 2 3 4 5 6 7 8 9 10 2 4 9 D D 6 B F D D 0 key spaces remain Press Confirm To Copy HoppingCode Duplicate 1 2 3 4 5 6 7 8 9 10 2 4 9 D D 6 B F D D 0 key spaces remain Programming Success Press Confirm To Copy Setting Version 300113 Boot V 0101 Z point 300113 HCD900 SN 100042 Setting >HOPP new SN Random3 display mode Button Language ENG Auto read Freq ON Fig. 31

battery, please connect it to our HCD-900 by duplicating cable in advance before you enter FixedCode Duplicate mode or HoppingCode Duplicate mode. 2. How to transmitting Seed Code from a REMOCON remote after duplication: 1) If there is only one Seed code for this remote: Press any 3 buttons at the same time. 2) If there are respective Seed codes for each button: Press the rest 3 buttons. Example: If you would like to transmit the Seed code for button 1, press button 2, 3 and 4 at the same time; If you would like to transmit the Seed code for button 2, press button 1, 3 and 4 at the same time. 3. Special rule for RMC-255CHM & RMC-255CHML: if you would like to copy both fixed code remotes & rolling code remotes into RMC-255CHM or RMC-255CHML by HCD-900, please ensure to copy fixed code remotes first(in FixedCode Duplicate mode) and then copy rolling code remotes(in HoppingCode Duplicate mode). If you do it reversely, the rolling code programmed will be covered by fixed code you copy later. Updated at Apr. 18, 2017